Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
提交 dbef807e 编写于 作者: Y Yuval Mintz 提交者： David S. Miller
浏览文件
操作

bnx2x: 1G sfp+ module handling 

Automatically lower requested link speed to 1G in case 1G SFP+
module is detected.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NYaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 a351d497
隐藏空白更改
内联 并排
Showing with 151 addition and 84 deletion
drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c
浏览文件 @ dbef807e
......@@ -187,7 +187,8 @@ static int bnx2x_get_port_type(struct bnx2x *bp)
int port_type;
u32 phy_idx = bnx2x_get_cur_phy_idx(bp);
switch (bp->link_params.phy[phy_idx].media_type) {
case ETH_PHY_SFP_FIBER:
case ETH_PHY_SFPP_10G_FIBER:
case ETH_PHY_SFP_1G_FIBER:
case ETH_PHY_XFP_FIBER:
case ETH_PHY_KR:
case ETH_PHY_CX4:
......@@ -220,6 +221,11 @@ static int bnx2x_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
(bp->port.supported[cfg_idx ^ 1] &
(SUPPORTED_TP | SUPPORTED_FIBRE));
cmd->advertising = bp->port.advertising[cfg_idx];
if (bp->link_params.phy[bnx2x_get_cur_phy_idx(bp)].media_type ==
ETH_PHY_SFP_1G_FIBER) {
cmd->supported &= ~(SUPPORTED_10000baseT_Full);
cmd->advertising &= ~(ADVERTISED_10000baseT_Full);
}
if ((bp->state == BNX2X_STATE_OPEN) && (bp->link_vars.link_up)) {
if (!(bp->flags & MF_FUNC_DIS)) {
......@@ -295,7 +301,7 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
{
struct bnx2x *bp = netdev_priv(dev);
u32 advertising, cfg_idx, old_multi_phy_config, new_multi_phy_config;
u32 speed;
u32 speed, phy_idx;
if (IS_MF_SD(bp))
return 0;
......@@ -550,9 +556,11 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
"10G half not supported\n");
return -EINVAL;
}
phy_idx = bnx2x_get_cur_phy_idx(bp);
if (!(bp->port.supported[cfg_idx]
& SUPPORTED_10000baseT_Full)) {
& SUPPORTED_10000baseT_Full) ||
(bp->link_params.phy[phy_idx].media_type ==
ETH_PHY_SFP_1G_FIBER)) {
DP(BNX2X_MSG_ETHTOOL,
"10G full not supported\n");
return -EINVAL;
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c
浏览文件 @ dbef807e
......@@ -4373,6 +4373,23 @@ static void bnx2x_warpcore_config_runtime(struct bnx2x_phy *phy,
} /*params->rx_tx_asic_rst*/
}
static void bnx2x_warpcore_config_sfi(struct bnx2x_phy *phy,
struct link_params *params)
{
u16 lane = bnx2x_get_warpcore_lane(phy, params);
struct bnx2x *bp = params->bp;
bnx2x_warpcore_clear_regs(phy, params, lane);
if ((params->req_line_speed[LINK_CONFIG_IDX(INT_PHY)] ==
SPEED_10000) &&
(phy->media_type != ETH_PHY_SFP_1G_FIBER)) {
DP(NETIF_MSG_LINK, "Setting 10G SFI\n");
bnx2x_warpcore_set_10G_XFI(phy, params, 0);
} else {
DP(NETIF_MSG_LINK, "Setting 1G Fiber\n");
bnx2x_warpcore_set_sgmii_speed(phy, params, 1, 0);
}
}
static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy,
struct link_params *params,
struct link_vars *vars)
......@@ -4433,19 +4450,11 @@ static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy,
break;
case PORT_HW_CFG_NET_SERDES_IF_SFI:
bnx2x_warpcore_clear_regs(phy, params, lane);
if (vars->line_speed == SPEED_10000) {
DP(NETIF_MSG_LINK, "Setting 10G SFI\n");
bnx2x_warpcore_set_10G_XFI(phy, params, 0);
} else if (vars->line_speed == SPEED_1000) {
DP(NETIF_MSG_LINK, "Setting 1G Fiber\n");
bnx2x_warpcore_set_sgmii_speed(
phy, params, 1, 0);
}
/* Issue Module detection */
if (bnx2x_is_sfp_module_plugged(phy, params))
bnx2x_sfp_module_detection(phy, params);
bnx2x_warpcore_config_sfi(phy, params);
break;
case PORT_HW_CFG_NET_SERDES_IF_DXGXS:
......@@ -6354,7 +6363,9 @@ int bnx2x_test_link(struct link_params *params, struct link_vars *vars,
for (phy_index = EXT_PHY1; phy_index < params->num_phys;
phy_index++) {
serdes_phy_type = ((params->phy[phy_index].media_type ==
ETH_PHY_SFP_FIBER) ||
ETH_PHY_SFPP_10G_FIBER) ||
(params->phy[phy_index].media_type ==
ETH_PHY_SFP_1G_FIBER) ||
(params->phy[phy_index].media_type ==
ETH_PHY_XFP_FIBER) ||
(params->phy[phy_index].media_type ==
......@@ -7891,7 +7902,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
{
struct bnx2x *bp = params->bp;
u32 sync_offset = 0, phy_idx, media_types;
u8 val, check_limiting_mode = 0;
u8 val[2], check_limiting_mode = 0;
*edc_mode = EDC_MODE_LIMITING;
phy->media_type = ETH_PHY_UNSPECIFIED;
......@@ -7899,13 +7910,13 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
if (bnx2x_read_sfp_module_eeprom(phy,
params,
SFP_EEPROM_CON_TYPE_ADDR,
1,
&val) != 0) {
2,
(u8 *)val) != 0) {
DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n");
return -EINVAL;
}
switch (val) {
switch (val[0]) {
case SFP_EEPROM_CON_TYPE_VAL_COPPER:
{
u8 copper_module_type;
......@@ -7943,13 +7954,29 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy,
break;
}
case SFP_EEPROM_CON_TYPE_VAL_LC:
phy->media_type = ETH_PHY_SFP_FIBER;
DP(NETIF_MSG_LINK, "Optic module detected\n");
check_limiting_mode = 1;
if ((val[1] & (SFP_EEPROM_COMP_CODE_SR_MASK |
SFP_EEPROM_COMP_CODE_LR_MASK |
SFP_EEPROM_COMP_CODE_LRM_MASK)) == 0) {
DP(NETIF_MSG_LINK, "1G Optic module detected\n");
phy->media_type = ETH_PHY_SFP_1G_FIBER;
phy->req_line_speed = SPEED_1000;
} else {
int idx, cfg_idx = 0;
DP(NETIF_MSG_LINK, "10G Optic module detected\n");
for (idx = INT_PHY; idx < MAX_PHYS; idx++) {
if (params->phy[idx].type == phy->type) {
cfg_idx = LINK_CONFIG_IDX(idx);
break;
}
}
phy->media_type = ETH_PHY_SFPP_10G_FIBER;
phy->req_line_speed = params->req_line_speed[cfg_idx];
}
break;
default:
DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n",
val);
val[0]);
return -EINVAL;
}
sync_offset = params->shmem_base +
......@@ -8479,14 +8506,34 @@ void bnx2x_handle_module_detect_int(struct link_params *params)
/* Call the handling function in case module is detected */
if (gpio_val == 0) {
bnx2x_set_mdio_clk(bp, params->chip_id, params->port);
bnx2x_set_aer_mmd(params, phy);
bnx2x_power_sfp_module(params, phy, 1);
bnx2x_set_gpio_int(bp, gpio_num,
MISC_REGISTERS_GPIO_INT_OUTPUT_CLR,
gpio_port);
if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0)
if (bnx2x_wait_for_sfp_module_initialized(phy, params) == 0) {
bnx2x_sfp_module_detection(phy, params);
else
if (CHIP_IS_E3(bp)) {
u16 rx_tx_in_reset;
/* In case WC is out of reset, reconfigure the
* link speed while taking into account 1G
* module limitation.
*/
bnx2x_cl45_read(bp, phy,
MDIO_WC_DEVAD,
MDIO_WC_REG_DIGITAL5_MISC6,
&rx_tx_in_reset);
if (!rx_tx_in_reset) {
bnx2x_warpcore_reset_lane(bp, phy, 1);
bnx2x_warpcore_config_sfi(phy, params);
bnx2x_warpcore_reset_lane(bp, phy, 0);
}
}
} else {
DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
}
} else {
u32 val = REG_RD(bp, params->shmem_base +
offsetof(struct shmem_region, dev_info.
......@@ -8938,6 +8985,63 @@ static void bnx2x_8727_hw_reset(struct bnx2x_phy *phy,
MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
}
static void bnx2x_8727_config_speed(struct bnx2x_phy *phy,
struct link_params *params)
{
struct bnx2x *bp = params->bp;
u16 tmp1, val;
/* Set option 1G speed */
if ((phy->req_line_speed == SPEED_1000) ||
(phy->media_type == ETH_PHY_SFP_1G_FIBER)) {
DP(NETIF_MSG_LINK, "Setting 1G force\n");
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD);
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1);
DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1);
/* Power down the XAUI until link is up in case of dual-media
* and 1G
*/
if (DUAL_MEDIA(params)) {
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8727_PCS_GP, &val);
val |= (3<<10);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8727_PCS_GP, val);
}
} else if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
((phy->speed_cap_mask &
PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) &&
((phy->speed_cap_mask &
PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) !=
PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0);
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300);
} else {
/* Since the 8727 has only single reset pin, need to set the 10G
* registers although it is default
*/
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL,
0x0020);
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2,
0x0008);
}
}
static int bnx2x_8727_config_init(struct bnx2x_phy *phy,
struct link_params *params,
struct link_vars *vars)
......@@ -9007,56 +9111,7 @@ static int bnx2x_8727_config_init(struct bnx2x_phy *phy,
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_LASI_RXSTAT, &tmp1);
/* Set option 1G speed */
if (phy->req_line_speed == SPEED_1000) {
DP(NETIF_MSG_LINK, "Setting 1G force\n");
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x40);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, 0xD);
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2, &tmp1);
DP(NETIF_MSG_LINK, "1.7 = 0x%x\n", tmp1);
/* Power down the XAUI until link is up in case of dual-media
* and 1G
*/
if (DUAL_MEDIA(params)) {
bnx2x_cl45_read(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8727_PCS_GP, &val);
val |= (3<<10);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_8727_PCS_GP, val);
}
} else if ((phy->req_line_speed == SPEED_AUTO_NEG) &&
((phy->speed_cap_mask &
PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) &&
((phy->speed_cap_mask &
PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) !=
PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) {
DP(NETIF_MSG_LINK, "Setting 1G clause37\n");
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL, 0);
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1300);
} else {
/* Since the 8727 has only single reset pin, need to set the 10G
* registers although it is default
*/
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_8727_MISC_CTRL,
0x0020);
bnx2x_cl45_write(bp, phy,
MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x0100);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, 0x2040);
bnx2x_cl45_write(bp, phy,
MDIO_PMA_DEVAD, MDIO_PMA_REG_10G_CTRL2,
0x0008);
}
bnx2x_8727_config_speed(phy, params);
/* Set 2-wire transfer rate of SFP+ module EEPROM
* to 100Khz since some DACs(direct attached cables) do
* not work at 400Khz.
......@@ -9183,6 +9238,9 @@ static void bnx2x_8727_handle_mod_abs(struct bnx2x_phy *phy,
bnx2x_sfp_module_detection(phy, params);
else
DP(NETIF_MSG_LINK, "SFP+ module is not initialized\n");
/* Reconfigure link speed based on module type limitations */
bnx2x_8727_config_speed(phy, params);
}
DP(NETIF_MSG_LINK, "8727 RX_ALARM_STATUS 0x%x\n",
......@@ -11327,7 +11385,7 @@ static struct bnx2x_phy phy_8706 = {
SUPPORTED_FIBRE |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
.media_type = ETH_PHY_SFP_FIBER,
.media_type = ETH_PHY_SFPP_10G_FIBER,
.ver_addr = 0,
.req_flow_ctrl = 0,
.req_line_speed = 0,
......@@ -11666,7 +11724,7 @@ static int bnx2x_populate_int_phy(struct bnx2x *bp, u32 shmem_base, u8 port,
SUPPORTED_FIBRE |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause);
phy->media_type = ETH_PHY_SFP_FIBER;
phy->media_type = ETH_PHY_SFPP_10G_FIBER;
break;
case PORT_HW_CFG_NET_SERDES_IF_KR:
phy->media_type = ETH_PHY_KR;
......
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h
浏览文件 @ dbef807e
......@@ -168,14 +168,15 @@ struct bnx2x_phy {
u32 supported;
u32 media_type;
#define ETH_PHY_UNSPECIFIED 0x0
#define ETH_PHY_SFP_FIBER 0x1
#define ETH_PHY_XFP_FIBER 0x2
#define ETH_PHY_DA_TWINAX 0x3
#define ETH_PHY_BASE_T 0x4
#define ETH_PHY_KR 0xf0
#define ETH_PHY_CX4 0xf1
#define ETH_PHY_NOT_PRESENT 0xff
#define ETH_PHY_UNSPECIFIED 0x0
#define ETH_PHY_SFPP_10G_FIBER 0x1
#define ETH_PHY_XFP_FIBER 0x2
#define ETH_PHY_DA_TWINAX 0x3
#define ETH_PHY_BASE_T 0x4
#define ETH_PHY_SFP_1G_FIBER 0x5
#define ETH_PHY_KR 0xf0
#define ETH_PHY_CX4 0xf1
#define ETH_PHY_NOT_PRESENT 0xff
/* The address in which version is located*/
u32 ver_addr;
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或