V4L/DVB (4797): Marvell 88ALP01 "cafe" driver

A driver for the Marvell M88ALP01 "CAFE" CMOS integrated camera
controller.  This driver has been renamed "cafe_ccic" since my previous
patch set.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Documentation/video4linux/cafe_ccic

+"cafe_ccic" is a driver for the Marvell 88ALP01 "cafe" CMOS camera
+controller.  This is the controller found in first-generation OLPC systems,
+and this driver was written with support from the OLPC project.
+
+Current status: the core driver works.  It can generate data in YUV422,
+RGB565, and RGB444 formats.  (Anybody looking at the code will see RGB32 as
+well, but that is a debugging aid which will be removed shortly).  VGA and
+QVGA modes work; CIF is there but the colors remain funky.  Only the OV7670
+sensor is known to work with this controller at this time.
+
+To try it out: either of these commands will work:
+
+     mplayer tv:// -tv driver=v4l2:width=640:height=480 -nosound
+     mplayer tv:// -tv driver=v4l2:width=640:height=480:outfmt=bgr16 -nosound
+
+The "xawtv" utility also works; gqcam does not, for unknown reasons.
+
+There are a few load-time options, most of which can be changed after
+loading via sysfs as well:
+
+ - alloc_bufs_at_load:  Normally, the driver will not allocate any DMA
+   buffers until the time comes to transfer data.  If this option is set,
+   then worst-case-sized buffers will be allocated at module load time.
+   This option nails down the memory for the life of the module, but
+   perhaps decreases the chances of an allocation failure later on.
+
+ - dma_buf_size: The size of DMA buffers to allocate.  Note that this
+   option is only consulted for load-time allocation; when buffers are
+   allocated at run time, they will be sized appropriately for the current
+   camera settings.
+
+ - n_dma_bufs: The controller can cycle through either two or three DMA
+   buffers.  Normally, the driver tries to use three buffers; on faster
+   systems, however, it will work well with only two.
+
+ - min_buffers: The minimum number of streaming I/O buffers that the driver
+   will consent to work with.  Default is one, but, on slower systems,
+   better behavior with mplayer can be achieved by setting to a higher
+   value (like six).
+
+ - max_buffers: The maximum number of streaming I/O buffers; default is
+   ten.  That number was carefully picked out of a hat and should not be
+   assumed to actually mean much of anything.
+
+ - flip: If this boolean parameter is set, the sensor will be instructed to
+   invert the video image.  Whether it makes sense is determined by how
+   your particular camera is mounted.
+
+Work is ongoing with this driver, stay tuned.
+
+jon
+
+Jonathan Corbet
+corbet@lwn.net

drivers/media/video/Kconfig

@@ -670,6 +670,15 @@ config VIDEO_M32R_AR_M64278
 	  To compile this driver as a module, choose M here: the
 	  module will be called arv.
 
+config VIDEO_CAFE_CCIC
+	tristate "Marvell 88ALP01 (Cafe) CMOS Camera Controller support"
+	depends on I2C && VIDEO_V4L2
+	select VIDEO_OV7670
+	---help---
+	  This is a video4linux2 driver for the Marvell 88ALP01 integrated
+	  CMOS camera controller.  This is the controller found on first-
+	  generation OLPC systems.
+
 #
 # USB Multimedia device configuration
 #

drivers/media/video/Makefile

@@ -92,6 +92,8 @@ obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
 obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
 obj-$(CONFIG_VIDEO_CX2341X) += cx2341x.o
 
+obj-$(CONFIG_VIDEO_CAFE_CCIC) += cafe_ccic.o
+
 obj-$(CONFIG_USB_DABUSB)        += dabusb.o
 obj-$(CONFIG_USB_OV511)         += ov511.o
 obj-$(CONFIG_USB_SE401)         += se401.o

drivers/media/video/cafe_ccic-regs.h

+/*
+ * Register definitions for the m88alp01 camera interface.  Offsets in bytes
+ * as given in the spec.
+ *
+ * Copyright 2006 One Laptop Per Child Association, Inc.
+ *
+ * Written by Jonathan Corbet, corbet@lwn.net.
+ *
+ * This file may be distributed under the terms of the GNU General
+ * Public License, version 2.
+ */
+#define REG_Y0BAR	0x00
+#define REG_Y1BAR	0x04
+#define REG_Y2BAR	0x08
+/* ... */
+
+#define REG_IMGPITCH	0x24	/* Image pitch register */
+#define   IMGP_YP_SHFT	  2		/* Y pitch params */
+#define   IMGP_YP_MASK	  0x00003ffc	/* Y pitch field */
+#define	  IMGP_UVP_SHFT	  18		/* UV pitch (planar) */
+#define   IMGP_UVP_MASK   0x3ffc0000
+#define REG_IRQSTATRAW	0x28	/* RAW IRQ Status */
+#define   IRQ_EOF0	  0x00000001	/* End of frame 0 */
+#define   IRQ_EOF1	  0x00000002	/* End of frame 1 */
+#define   IRQ_EOF2	  0x00000004	/* End of frame 2 */
+#define   IRQ_SOF0	  0x00000008	/* Start of frame 0 */
+#define   IRQ_SOF1	  0x00000010	/* Start of frame 1 */
+#define   IRQ_SOF2	  0x00000020	/* Start of frame 2 */
+#define   IRQ_OVERFLOW	  0x00000040	/* FIFO overflow */
+#define   IRQ_TWSIW	  0x00010000	/* TWSI (smbus) write */
+#define   IRQ_TWSIR	  0x00020000	/* TWSI read */
+#define   IRQ_TWSIE	  0x00040000	/* TWSI error */
+#define   TWSIIRQS (IRQ_TWSIW|IRQ_TWSIR|IRQ_TWSIE)
+#define   FRAMEIRQS (IRQ_EOF0|IRQ_EOF1|IRQ_EOF2|IRQ_SOF0|IRQ_SOF1|IRQ_SOF2)
+#define   ALLIRQS (TWSIIRQS|FRAMEIRQS|IRQ_OVERFLOW)
+#define REG_IRQMASK	0x2c	/* IRQ mask - same bits as IRQSTAT */
+#define REG_IRQSTAT	0x30	/* IRQ status / clear */
+
+#define REG_IMGSIZE	0x34	/* Image size */
+#define  IMGSZ_V_MASK	  0x1fff0000
+#define  IMGSZ_V_SHIFT	  16
+#define	 IMGSZ_H_MASK	  0x00003fff
+#define REG_IMGOFFSET	0x38	/* IMage offset */
+
+#define REG_CTRL0	0x3c	/* Control 0 */
+#define   C0_ENABLE	  0x00000001	/* Makes the whole thing go */
+
+/* Mask for all the format bits */
+#define   C0_DF_MASK	  0x00fffffc    /* Bits 2-23 */
+
+/* RGB ordering */
+#define   C0_RGB4_RGBX	  0x00000000
+#define	  C0_RGB4_XRGB	  0x00000004
+#define	  C0_RGB4_BGRX	  0x00000008
+#define   C0_RGB4_XBGR	  0x0000000c
+#define   C0_RGB5_RGGB	  0x00000000
+#define	  C0_RGB5_GRBG	  0x00000004
+#define	  C0_RGB5_GBRG	  0x00000008
+#define   C0_RGB5_BGGR	  0x0000000c
+
+/* Spec has two fields for DIN and DOUT, but they must match, so
+   combine them here. */
+#define   C0_DF_YUV	  0x00000000    /* Data is YUV	    */
+#define   C0_DF_RGB	  0x000000a0	/* ... RGB		    */
+#define   C0_DF_BAYER     0x00000140	/* ... Bayer                */
+/* 8-8-8 must be missing from the below - ask */
+#define   C0_RGBF_565	  0x00000000
+#define   C0_RGBF_444	  0x00000800
+#define   C0_RGB_BGR	  0x00001000	/* Blue comes first */
+#define   C0_YUV_PLANAR	  0x00000000	/* YUV 422 planar format */
+#define   C0_YUV_PACKED	  0x00008000	/* YUV 422 packed	*/
+#define   C0_YUV_420PL	  0x0000a000	/* YUV 420 planar	*/
+/* Think that 420 packed must be 111 - ask */
+#define	  C0_YUVE_YUYV	  0x00000000	/* Y1CbY0Cr 		*/
+#define	  C0_YUVE_YVYU	  0x00010000	/* Y1CrY0Cb 		*/
+#define	  C0_YUVE_VYUY	  0x00020000	/* CrY1CbY0 		*/
+#define	  C0_YUVE_UYVY	  0x00030000	/* CbY1CrY0 		*/
+#define   C0_YUVE_XYUV	  0x00000000    /* 420: .YUV		*/
+#define	  C0_YUVE_XYVU	  0x00010000	/* 420: .YVU 		*/
+#define	  C0_YUVE_XUVY	  0x00020000	/* 420: .UVY 		*/
+#define	  C0_YUVE_XVUY	  0x00030000	/* 420: .VUY 		*/
+/* Bayer bits 18,19 if needed */
+#define   C0_HPOL_LOW	  0x01000000	/* HSYNC polarity active low */
+#define   C0_VPOL_LOW	  0x02000000	/* VSYNC polarity active low */
+#define   C0_VCLK_LOW	  0x04000000	/* VCLK on falling edge */
+#define   C0_DOWNSCALE	  0x08000000	/* Enable downscaler */
+#define	  C0_SIFM_MASK	  0xc0000000	/* SIF mode bits */
+#define   C0_SIF_HVSYNC	  0x00000000	/* Use H/VSYNC */
+#define   CO_SOF_NOSYNC	  0x40000000	/* Use inband active signaling */
+
+
+#define REG_CTRL1	0x40	/* Control 1 */
+#define   C1_444ALPHA	  0x00f00000	/* Alpha field in RGB444 */
+#define   C1_ALPHA_SHFT	  20
+#define   C1_DMAB32	  0x00000000	/* 32-byte DMA burst */
+#define   C1_DMAB16	  0x02000000	/* 16-byte DMA burst */
+#define	  C1_DMAB64	  0x04000000	/* 64-byte DMA burst */
+#define	  C1_DMAB_MASK	  0x06000000
+#define   C1_TWOBUFS	  0x08000000	/* Use only two DMA buffers */
+#define   C1_PWRDWN	  0x10000000	/* Power down */
+
+#define REG_CLKCTRL	0x88	/* Clock control */
+#define   CLK_DIV_MASK	  0x0000ffff	/* Upper bits RW "reserved" */
+
+#define REG_GPR		0xb4	/* General purpose register.  This
+				   controls inputs to the power and reset
+				   pins on the OV7670 used with OLPC;
+				   other deployments could differ.  */
+#define   GPR_C1EN	  0x00000020	/* Pad 1 (power down) enable */
+#define   GPR_C0EN	  0x00000010	/* Pad 0 (reset) enable */
+#define	  GPR_C1	  0x00000002	/* Control 1 value */
+/*
+ * Control 0 is wired to reset on OLPC machines.  For ov7x sensors,
+ * it is active low, for 0v6x, instead, it's active high.  What
+ * fun.
+ */
+#define   GPR_C0	  0x00000001	/* Control 0 value */
+
+#define REG_TWSIC0	0xb8	/* TWSI (smbus) control 0 */
+#define   TWSIC0_EN       0x00000001	/* TWSI enable */
+#define   TWSIC0_MODE	  0x00000002	/* 1 = 16-bit, 0 = 8-bit */
+#define   TWSIC0_SID	  0x000003fc	/* Slave ID */
+#define   TWSIC0_SID_SHIFT 2
+#define   TWSIC0_CLKDIV   0x0007fc00	/* Clock divider */
+#define   TWSIC0_MASKACK  0x00400000	/* Mask ack from sensor */
+#define   TWSIC0_OVMAGIC  0x00800000	/* Make it work on OV sensors */
+
+#define REG_TWSIC1	0xbc	/* TWSI control 1 */
+#define   TWSIC1_DATA	  0x0000ffff	/* Data to/from camchip */
+#define   TWSIC1_ADDR	  0x00ff0000	/* Address (register) */
+#define   TWSIC1_ADDR_SHIFT 16
+#define   TWSIC1_READ	  0x01000000	/* Set for read op */
+#define   TWSIC1_WSTAT	  0x02000000	/* Write status */
+#define   TWSIC1_RVALID	  0x04000000	/* Read data valid */
+#define   TWSIC1_ERROR	  0x08000000	/* Something screwed up */
+
+
+#define REG_UBAR	0xc4	/* Upper base address register */
+
+/*
+ * Here's the weird global control registers which are said to live
+ * way up here.
+ */
+#define REG_GL_CSR     0x3004  /* Control/status register */
+#define   GCSR_SRS	 0x00000001	/* SW Reset set */
+#define   GCSR_SRC  	 0x00000002	/* SW Reset clear */
+#define	  GCSR_MRS	 0x00000004	/* Master reset set */
+#define	  GCSR_MRC	 0x00000008	/* HW Reset clear */
+#define   GCSR_CCIC_EN   0x00004000    /* CCIC Clock enable */
+#define REG_GL_IMASK   0x300c  /* Interrupt mask register */
+#define   GIMSK_CCIC_EN          0x00000004    /* CCIC Interrupt enable */
+
+#define REG_LEN                REG_GL_IMASK + 4
+
+
+/*
+ * Useful stuff that probably belongs somewhere global.
+ */
+#define VGA_WIDTH	640
+#define VGA_HEIGHT	480

include/linux/i2c-id.h

@@ -250,6 +250,7 @@
 #define I2C_HW_SMBUS_OV518	0x04000f /* OV518(+) USB 1.1 webcam ICs */
 #define I2C_HW_SMBUS_OV519	0x040010 /* OV519 USB 1.1 webcam IC */
 #define I2C_HW_SMBUS_OVFX2	0x040011 /* Cypress/OmniVision FX2 webcam */
+#define I2C_HW_SMBUS_CAFE	0x040012 /* Marvell 88ALP01 "CAFE" cam  */
 
 /* --- ISA pseudo-adapter						*/
 #define I2C_HW_ISA		0x050000