ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ

From "Chip Errata for the i.MX 6Dual/6Quad"

ERR006687 ENET: Only the ENET wake-up interrupt request can wake the
system from Wait mode.

The ENET block generates many interrupts. Only one of these interrupt lines
is connected to the General Power Controller (GPC) block, but a logical OR
of all of the ENET interrupts is connected to the General Interrupt Controller
(GIC). When the system enters Wait mode, a normal RX Done or TX Done does not
wake up the system because the GPC cannot see this interrupt. This impacts
performance of the ENET block because its interrupts are serviced only when
the chip exits Wait mode due to an interrupt from some other wake-up source.

Adding MX6QDL_PAD_GPIO_6__ENET_IRQ is the 1st step to
workaround this problem.

The input reg is set to 0x3c to set IOMUX_OBSRV_MUX1 to ENET_IRQ.
The mux reg value is 0x11, so that the observable mux is routed to
this pin and to the gpio controller(sion bit). These magic values
come from Ranjani Vaidyanathan's patch:
"ENGR00257847-1 MX6Q/DL-Fix Ethernet performance issue when WAIT mode is active"
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

arch/arm/boot/dts/imx6dl-pinfunc.h

@@ -755,6 +755,7 @@
 #define MX6QDL_PAD_GPIO_5__I2C3_SCL                 0x230 0x600 0x878 0x6 0x2
 #define MX6QDL_PAD_GPIO_5__ARM_EVENTI               0x230 0x600 0x000 0x7 0x0
 #define MX6QDL_PAD_GPIO_6__ESAI_TX_CLK              0x234 0x604 0x840 0x0 0x1
+#define MX6QDL_PAD_GPIO_6__ENET_IRQ		    0x234 0x604 0x03c 0x11 0xff000609
 #define MX6QDL_PAD_GPIO_6__I2C3_SDA                 0x234 0x604 0x87c 0x2 0x2
 #define MX6QDL_PAD_GPIO_6__GPIO1_IO06               0x234 0x604 0x000 0x5 0x0
 #define MX6QDL_PAD_GPIO_6__SD2_LCTL                 0x234 0x604 0x000 0x6 0x0

arch/arm/boot/dts/imx6q-pinfunc.h

@@ -673,6 +673,7 @@
 #define MX6QDL_PAD_GPIO_3__USB_H1_OC                0x22c 0x5fc 0x948 0x6 0x1
 #define MX6QDL_PAD_GPIO_3__MLB_CLK                  0x22c 0x5fc 0x900 0x7 0x1
 #define MX6QDL_PAD_GPIO_6__ESAI_TX_CLK              0x230 0x600 0x870 0x0 0x1
+#define MX6QDL_PAD_GPIO_6__ENET_IRQ		    0x230 0x600 0x03c 0x11 0xff000609
 #define MX6QDL_PAD_GPIO_6__I2C3_SDA                 0x230 0x600 0x8ac 0x2 0x1
 #define MX6QDL_PAD_GPIO_6__GPIO1_IO06               0x230 0x600 0x000 0x5 0x0
 #define MX6QDL_PAD_GPIO_6__SD2_LCTL                 0x230 0x600 0x000 0x6 0x0