Merge branch 'bcm7xxx-next'

Florian Fainelli says:

====================
net: phy: bcm7xxx: workaround updates

This patch series contains some updates to the Broadcom BCM7xxx internal
PHY driver, including:

- removing an annonying print that would appear during interface up/down and
  suspend/resume cycles
- drop a workaround sequence for a non-production PHY revision
- add new workarounds for the latest and greatest PHY devices found out there
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/phy/bcm7xxx.c

@@ -39,45 +39,15 @@
 
 #define AFE_RXCONFIG_0			MISC_ADDR(0x38, 0)
 #define AFE_RXCONFIG_1			MISC_ADDR(0x38, 1)
+#define AFE_RXCONFIG_2			MISC_ADDR(0x38, 2)
 #define AFE_RX_LP_COUNTER		MISC_ADDR(0x38, 3)
 #define AFE_TX_CONFIG			MISC_ADDR(0x39, 0)
+#define AFE_VDCA_ICTRL_0		MISC_ADDR(0x39, 1)
+#define AFE_VDAC_OTHERS_0		MISC_ADDR(0x39, 3)
 #define AFE_HPF_TRIM_OTHERS		MISC_ADDR(0x3a, 0)
 
 #define CORE_EXPB0			0xb0
 
-static int bcm7445_config_init(struct phy_device *phydev)
-{
-	int ret;
-	const struct bcm7445_regs {
-		int reg;
-		u16 value;
-	} bcm7445_regs_cfg[] = {
-		/* increases ADC latency by 24ns */
-		{ MII_BCM54XX_EXP_SEL, 0x0038 },
-		{ MII_BCM54XX_EXP_DATA, 0xAB95 },
-		/* increases internal 1V LDO voltage by 5% */
-		{ MII_BCM54XX_EXP_SEL, 0x2038 },
-		{ MII_BCM54XX_EXP_DATA, 0xBB22 },
-		/* reduce RX low pass filter corner frequency */
-		{ MII_BCM54XX_EXP_SEL, 0x6038 },
-		{ MII_BCM54XX_EXP_DATA, 0xFFC5 },
-		/* reduce RX high pass filter corner frequency */
-		{ MII_BCM54XX_EXP_SEL, 0x003a },
-		{ MII_BCM54XX_EXP_DATA, 0x2002 },
-	};
-	unsigned int i;
-
-	for (i = 0; i < ARRAY_SIZE(bcm7445_regs_cfg); i++) {
-		ret = phy_write(phydev,
-				bcm7445_regs_cfg[i].reg,
-				bcm7445_regs_cfg[i].value);
-		if (ret)
-			return ret;
-	}
-
-	return 0;
-}
-
 static void phy_write_exp(struct phy_device *phydev,
 					u16 reg, u16 value)
 {
@@ -102,7 +72,16 @@ static void phy_write_misc(struct phy_device *phydev,
 	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
 }
 
-static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev)
+static void r_rc_cal_reset(struct phy_device *phydev)
+{
+	/* Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0010);
+
+	/* Disable Reset R_AL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0000);
+}
+
+static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
 {
 	/* Increase VCO range to prevent unlocking problem of PLL at low
 	 * temp
@@ -123,11 +102,7 @@ static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev)
 	/* Switch to CORE_BASE1E */
 	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);
 
-	/* Reset R_CAL/RC_CAL Engine */
-	phy_write_exp(phydev, CORE_EXPB0, 0x0010);
-
-	/* Disable Reset R_CAL/RC_CAL Engine */
-	phy_write_exp(phydev, CORE_EXPB0, 0x0000);
+	r_rc_cal_reset(phydev);
 
 	/* write AFE_RXCONFIG_0 */
 	phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);
@@ -147,6 +122,71 @@ static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev)
 	return 0;
 }
 
+static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
+{
+	/* AFE_RXCONFIG_0 */
+	phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);
+
+	/* AFE_RXCONFIG_1 */
+	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
+
+	/* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2 code */
+	phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);
+
+	/* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
+	phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
+
+	/* AFE_TX_CONFIG, set 1000BT Cfeed=110 for all ports */
+	phy_write_misc(phydev, AFE_TX_CONFIG, 0x0061);
+
+	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
+	phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
+
+	/* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
+	phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);
+
+	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
+	 * offset for HT=0 code
+	 */
+	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
+
+	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
+	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
+
+	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
+	phy_write_misc(phydev, DSP_TAP10, 0x011b);
+
+	/* Reset R_CAL/RC_CAL engine */
+	r_rc_cal_reset(phydev);
+
+	return 0;
+}
+
+static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
+{
+	/* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
+	phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
+
+	/* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB symmetry */
+	phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
+
+	/* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set rCal
+	 * offset for HT=0 code
+	 */
+	phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
+
+	/* CORE_BASE1E, force trim to overwrite and set I_ext trim to 0000 */
+	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
+
+	/* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
+	phy_write_misc(phydev, DSP_TAP10, 0x011b);
+
+	/* Reset R_CAL/RC_CAL engine */
+	r_rc_cal_reset(phydev);
+
+	return 0;
+}
+
 static int bcm7xxx_apd_enable(struct phy_device *phydev)
 {
 	int val;
@@ -200,15 +240,21 @@ static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
 	u8 patch = PHY_BRCM_7XXX_PATCH(phydev->dev_flags);
 	int ret = 0;
 
-	dev_info(&phydev->dev, "PHY revision: 0x%02x, patch: %d\n", rev, patch);
+	pr_info_once("%s: %s PHY revision: 0x%02x, patch: %d\n",
+		     dev_name(&phydev->dev), phydev->drv->name, rev, patch);
 
 	switch (rev) {
-	case 0xa0:
 	case 0xb0:
-		ret = bcm7445_config_init(phydev);
+		ret = bcm7xxx_28nm_b0_afe_config_init(phydev);
+		break;
+	case 0xd0:
+		ret = bcm7xxx_28nm_d0_afe_config_init(phydev);
+		break;
+	case 0xe0:
+	case 0xf0:
+		ret = bcm7xxx_28nm_e0_plus_afe_config_init(phydev);
 		break;
 	default:
-		ret = bcm7xxx_28nm_afe_config_init(phydev);
 		break;
 	}
 
@@ -336,7 +382,7 @@ static int bcm7xxx_dummy_config_init(struct phy_device *phydev)
 	.features	= PHY_GBIT_FEATURES |				\
 			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,	\
 	.flags		= PHY_IS_INTERNAL,				\
-	.config_init	= bcm7xxx_28nm_afe_config_init,			\
+	.config_init	= bcm7xxx_28nm_config_init,			\
 	.config_aneg	= genphy_config_aneg,				\
 	.read_status	= genphy_read_status,				\
 	.resume		= bcm7xxx_28nm_resume,				\