Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (22 commits)
  hwmon: (via-cputemp) Remove bogus "SHOW" global variable
  hwmon: jc42 depends on I2C
  hwmon: (pc87427) Add a maintainer
  hwmon: (pc87427) Move sysfs file removal to a separate function
  hwmon: (pc87427) Add temperature monitoring support
  hwmon: (pc87427) Add support for the second logical device
  hwmon: (pc87427) Add support for manual fan speed control
  hwmon: (pc87427) Minor style cleanups
  hwmon: (pc87427) Handle disabled fan inputs properly
  hwmon: (w83627ehf) Add support for W83667HG-B
  hwmon: (w83627ehf) Driver cleanup
  hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller
  hwmon: Remove in[0-*]_fault from sysfs-interface
  hwmon: Add 4 current alarm/beep attributes to sysfs-interface
  hwmon: Add 3 critical limit attributes to sysfs-interface
  hwmon: (asc7621) Clean up and improve detect function
  hwmon: (it87) Export labels for internal sensors
  hwmon: (lm75) Add suspend/resume feature
  hwmon: (emc1403) Add power support
  hwmon: (ltc4245) Expose all GPIO pins as analog voltages
  ...

Documentation/hwmon/emc2103

+Kernel driver emc2103
+======================
+
+Supported chips:
+  * SMSC EMC2103
+    Addresses scanned: I2C 0x2e
+    Prefix: 'emc2103'
+    Datasheet: Not public
+
+Authors:
+        Steve Glendinning <steve.glendinning@smsc.com>
+
+Description
+-----------
+
+The Standard Microsystems Corporation (SMSC) EMC2103 chips
+contain up to 4 temperature sensors and a single fan controller.
+
+Fan rotation speeds are reported in RPM (rotations per minute). An alarm is
+triggered if the rotation speed has dropped below a programmable limit. Fan
+readings can be divided by a programmable divider (1, 2, 4 or 8) to give
+the readings more range or accuracy. Not all RPM values can accurately be
+represented, so some rounding is done. With a divider of 1, the lowest
+representable value is 480 RPM.
+
+This driver supports RPM based control, to use this a fan target
+should be written to fan1_target and pwm1_enable should be set to 3.
+
+The 2103-2 and 2103-4 variants have a third temperature sensor, which can
+be connected to two anti-parallel diodes.  These values can be read
+as temp3 and temp4.  If only one diode is attached to this channel, temp4
+will show as "fault".  The module parameter "apd=0" can be used to suppress
+this 4th channel when anti-parallel diodes are not fitted.

Documentation/hwmon/ltc4245

@@ -72,9 +72,31 @@ in6_min_alarm		5v  output undervoltage alarm
 in7_min_alarm		3v  output undervoltage alarm
 in8_min_alarm		Vee (-12v) output undervoltage alarm
 
-in9_input		GPIO voltage data
+in9_input		GPIO voltage data (see note 1)
+in10_input		GPIO voltage data (see note 1)
+in11_input		GPIO voltage data (see note 1)
 
 power1_input		12v power usage (mW)
 power2_input		5v  power usage (mW)
 power3_input		3v  power usage (mW)
 power4_input		Vee (-12v) power usage (mW)
+
+
+Note 1
+------
+
+If you have NOT configured the driver to sample all GPIO pins as analog
+voltages, then the in10_input and in11_input sysfs attributes will not be
+created. The driver will sample the GPIO pin that is currently connected to the
+ADC as an analog voltage, and report the value in in9_input.
+
+If you have configured the driver to sample all GPIO pins as analog voltages,
+then they will be sampled in round-robin fashion. If userspace reads too
+slowly, -EAGAIN will be returned when you read the sysfs attribute containing
+the sensor reading.
+
+The LTC4245 chip can be configured to sample all GPIO pins with two methods:
+1) platform data -- see include/linux/i2c/ltc4245.h
+2) OF device tree -- add the "ltc4245,use-extra-gpios" property to each chip
+
+The default mode of operation is to sample a single GPIO pin.

Documentation/hwmon/pc87427

@@ -18,10 +18,11 @@ Description
 
 The National Semiconductor Super I/O chip includes complete hardware
 monitoring capabilities. It can monitor up to 18 voltages, 8 fans and
-6 temperature sensors. Only the fans are supported at the moment.
+6 temperature sensors. Only the fans and temperatures are supported at
+the moment, voltages aren't.
 
-This chip also has fan controlling features, which are not yet supported
-by this driver either.
+This chip also has fan controlling features (up to 4 PWM outputs),
+which are partly supported by this driver.
 
 The driver assumes that no more than one chip is present, which seems
 reasonable.
@@ -36,3 +37,23 @@ signal. Speeds down to 83 RPM can be measured.
 An alarm is triggered if the rotation speed drops below a programmable
 limit. Another alarm is triggered if the speed is too low to be measured
 (including stalled or missing fan).
+
+
+Fan Speed Control
+-----------------
+
+Fan speed can be controlled by PWM outputs. There are 4 possible modes:
+always off, always on, manual and automatic. The latter isn't supported
+by the driver: you can only return to that mode if it was the original
+setting, and the configuration interface is missing.
+
+
+Temperature Monitoring
+----------------------
+
+The PC87427 relies on external sensors (following the SensorPath
+standard), so the resolution and range depend on the type of sensor
+connected. The integer part can be 8-bit or 9-bit, and can be signed or
+not. I couldn't find a way to figure out the external sensor data
+temperature format, so user-space adjustment (typically by a factor 2)
+may be required.

Documentation/hwmon/sysfs-interface

@@ -107,10 +107,24 @@ in[0-*]_min	Voltage min value.
 		Unit: millivolt
 		RW
 		
+in[0-*]_lcrit	Voltage critical min value.
+		Unit: millivolt
+		RW
+		If voltage drops to or below this limit, the system may
+		take drastic action such as power down or reset. At the very
+		least, it should report a fault.
+
 in[0-*]_max	Voltage max value.
 		Unit: millivolt
 		RW
 		
+in[0-*]_crit	Voltage critical max value.
+		Unit: millivolt
+		RW
+		If voltage reaches or exceeds this limit, the system may
+		take drastic action such as power down or reset. At the very
+		least, it should report a fault.
+
 in[0-*]_input	Voltage input value.
 		Unit: millivolt
 		RO
@@ -284,7 +298,7 @@ temp[1-*]_input Temperature input value.
 		Unit: millidegree Celsius
 		RO
 
-temp[1-*]_crit	Temperature critical value, typically greater than
+temp[1-*]_crit	Temperature critical max value, typically greater than
 		corresponding temp_max values.
 		Unit: millidegree Celsius
 		RW
@@ -296,6 +310,11 @@ temp[1-*]_crit_hyst
 		from the critical value.
 		RW
 
+temp[1-*]_lcrit	Temperature critical min value, typically lower than
+		corresponding temp_min values.
+		Unit: millidegree Celsius
+		RW
+
 temp[1-*]_offset
 		Temperature offset which is added to the temperature reading
 		by the chip.
@@ -344,9 +363,6 @@ Also see the Alarms section for status flags associated with temperatures.
 * Currents *
 ************
 
-Note that no known chip provides current measurements as of writing,
-so this part is theoretical, so to say.
-
 curr[1-*]_max	Current max value
 		Unit: milliampere
 		RW
@@ -471,6 +487,7 @@ limit-related alarms, not both. The driver should just reflect the hardware
 implementation.
 
 in[0-*]_alarm
+curr[1-*]_alarm
 fan[1-*]_alarm
 temp[1-*]_alarm
 		Channel alarm
@@ -482,6 +499,8 @@ OR
 
 in[0-*]_min_alarm
 in[0-*]_max_alarm
+curr[1-*]_min_alarm
+curr[1-*]_max_alarm
 fan[1-*]_min_alarm
 fan[1-*]_max_alarm
 temp[1-*]_min_alarm
@@ -497,7 +516,6 @@ to notify open diodes, unconnected fans etc. where the hardware
 supports it. When this boolean has value 1, the measurement for that
 channel should not be trusted.
 
-in[0-*]_fault
 fan[1-*]_fault
 temp[1-*]_fault
 		Input fault condition
@@ -513,6 +531,7 @@ beep_enable	Master beep enable
 		RW
 
 in[0-*]_beep
+curr[1-*]_beep
 fan[1-*]_beep
 temp[1-*]_beep
 		Channel beep

Documentation/hwmon/w83627ehf

@@ -20,6 +20,10 @@ Supported chips:
     Prefix: 'w83667hg'
     Addresses scanned: ISA address retrieved from Super I/O registers
     Datasheet: not available
+  * Winbond W83667HG-B
+    Prefix: 'w83667hg'
+    Addresses scanned: ISA address retrieved from Super I/O registers
+    Datasheet: Available from Nuvoton upon request
 
 Authors:
         Jean Delvare <khali@linux-fr.org>
@@ -32,8 +36,8 @@ Description
 -----------
 
 This driver implements support for the Winbond W83627EHF, W83627EHG,
-W83627DHG, W83627DHG-P and W83667HG super I/O chips. We will refer to them
-collectively as Winbond chips.
+W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips.
+We will refer to them collectively as Winbond chips.
 
 The chips implement three temperature sensors, five fan rotation
 speed sensors, ten analog voltage sensors (only nine for the 627DHG), one
@@ -68,14 +72,15 @@ follows:
 temp1 -> pwm1
 temp2 -> pwm2
 temp3 -> pwm3
-prog  -> pwm4 (not on 667HG; the programmable setting is not supported by
-	       the driver)
+prog  -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not
+	       supported by the driver)
 
 /sys files
 ----------
 
 name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG,
-       it is set to "w83627ehf" and for the W83627DHG it is set to "w83627dhg"
+       it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg",
+       and for the W83667HG it is set to "w83667hg".
 
 pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range:
 	   0 (stop) to 255 (full)

MAINTAINERS

@@ -4402,6 +4402,13 @@ M:	Jim Cromie <jim.cromie@gmail.com>
 S:	Maintained
 F:	drivers/char/pc8736x_gpio.c
 
+PC87427 HARDWARE MONITORING DRIVER
+M:	Jean Delvare <khali@linux-fr.org>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	Documentation/hwmon/pc87427
+F:	drivers/hwmon/pc87427.c
+
 PCA9532 LED DRIVER
 M:	Riku Voipio <riku.voipio@iki.fi>
 S:	Maintained
@@ -5279,6 +5286,13 @@ S:	Maintained
 F:	Documentation/hwmon/smm665
 F:	drivers/hwmon/smm665.c
 
+SMSC EMC2103 HARDWARE MONITOR DRIVER
+M:	Steve Glendinning <steve.glendinning@smsc.com>
+L:	lm-sensors@lm-sensors.org
+S:	Supported
+F:	Documentation/hwmon/emc2103
+F:	drivers/hwmon/emc2103.c
+
 SMSC47B397 HARDWARE MONITOR DRIVER
 M:	"Mark M. Hoffman" <mhoffman@lightlink.com>
 L:	lm-sensors@lm-sensors.org

drivers/hwmon/Kconfig

@@ -465,6 +465,7 @@ config SENSORS_JZ4740
 
 config SENSORS_JC42
 	tristate "JEDEC JC42.4 compliant temperature sensors"
+	depends on I2C
 	help
 	  If you say yes here you get support for Jedec JC42.4 compliant
 	  temperature sensors. Support will include, but not be limited to,
@@ -711,7 +712,8 @@ config SENSORS_PC87427
 	  functions of the National Semiconductor PC87427 Super-I/O chip.
 	  The chip has two distinct logical devices, one for fan speed
 	  monitoring and control, and one for voltage and temperature
-	  monitoring. Only fan speed monitoring is supported right now.
+	  monitoring. Fan speed monitoring and control are supported, as
+	  well as temperature monitoring. Voltages aren't supported yet.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called pc87427.
@@ -804,6 +806,16 @@ config SENSORS_EMC1403
 	  Threshold values can be configured using sysfs.
 	  Data from the different diodes are accessible via sysfs.
 
+config SENSORS_EMC2103
+	tristate "SMSC EMC2103"
+	depends on I2C
+	help
+	  If you say yes here you get support for the temperature
+	  and fan sensors of the SMSC EMC2103 chips.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called emc2103.
+
 config SENSORS_SMSC47M1
 	tristate "SMSC LPC47M10x and compatibles"
 	help

drivers/hwmon/Makefile

@@ -43,6 +43,7 @@ obj-$(CONFIG_SENSORS_PKGTEMP)	+= pkgtemp.o
 obj-$(CONFIG_SENSORS_DME1737)	+= dme1737.o
 obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o
 obj-$(CONFIG_SENSORS_EMC1403)	+= emc1403.o
+obj-$(CONFIG_SENSORS_EMC2103)	+= emc2103.o
 obj-$(CONFIG_SENSORS_F71805F)	+= f71805f.o
 obj-$(CONFIG_SENSORS_F71882FG)	+= f71882fg.o
 obj-$(CONFIG_SENSORS_F75375S)	+= f75375s.o

drivers/hwmon/asc7621.c

@@ -1150,9 +1150,6 @@ static int asc7621_detect(struct i2c_client *client,
 {
 	struct i2c_adapter *adapter = client->adapter;
 	int company, verstep, chip_index;
-	struct device *dev;
-
-	dev = &client->dev;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
 		return -ENODEV;
@@ -1169,13 +1166,11 @@ static int asc7621_detect(struct i2c_client *client,
 
 		if (company == asc7621_chips[chip_index].company_id &&
 		    verstep == asc7621_chips[chip_index].verstep_id) {
-			strlcpy(client->name, asc7621_chips[chip_index].name,
-				I2C_NAME_SIZE);
 			strlcpy(info->type, asc7621_chips[chip_index].name,
 				I2C_NAME_SIZE);
 
-			dev_info(&adapter->dev, "Matched %s\n",
-				 asc7621_chips[chip_index].name);
+			dev_info(&adapter->dev, "Matched %s at 0x%02x\n",
+				 asc7621_chips[chip_index].name, client->addr);
 			return 0;
 		}
 	}

drivers/hwmon/emc1403.c

@@ -89,6 +89,35 @@ static ssize_t store_temp(struct device *dev,
 	return count;
 }
 
+static ssize_t store_bit(struct device *dev,
+		struct device_attribute *attr, const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct thermal_data *data = i2c_get_clientdata(client);
+	struct sensor_device_attribute_2 *sda = to_sensor_dev_attr_2(attr);
+	unsigned long val;
+	int retval;
+
+	if (strict_strtoul(buf, 10, &val))
+		return -EINVAL;
+
+	mutex_lock(&data->mutex);
+	retval = i2c_smbus_read_byte_data(client, sda->nr);
+	if (retval < 0)
+		goto fail;
+
+	retval &= ~sda->index;
+	if (val)
+		retval |= sda->index;
+
+	retval = i2c_smbus_write_byte_data(client, sda->index, retval);
+	if (retval == 0)
+		retval = count;
+fail:
+	mutex_unlock(&data->mutex);
+	return retval;
+}
+
 static ssize_t show_hyst(struct device *dev,
 			struct device_attribute *attr, char *buf)
 {
@@ -200,6 +229,9 @@ static SENSOR_DEVICE_ATTR_2(temp3_crit_alarm, S_IRUGO,
 static SENSOR_DEVICE_ATTR(temp3_crit_hyst, S_IRUGO | S_IWUSR,
 	show_hyst, store_hyst, 0x1A);
 
+static SENSOR_DEVICE_ATTR_2(power_state, S_IRUGO | S_IWUSR,
+	show_bit, store_bit, 0x03, 0x40);
+
 static struct attribute *mid_att_thermal[] = {
 	&sensor_dev_attr_temp1_min.dev_attr.attr,
 	&sensor_dev_attr_temp1_max.dev_attr.attr,
@@ -225,6 +257,7 @@ static struct attribute *mid_att_thermal[] = {
 	&sensor_dev_attr_temp3_max_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp3_crit_alarm.dev_attr.attr,
 	&sensor_dev_attr_temp3_crit_hyst.dev_attr.attr,
+	&sensor_dev_attr_power_state.dev_attr.attr,
 	NULL
 };
 

drivers/hwmon/it87.c

@@ -259,6 +259,7 @@ struct it87_sio_data {
 	u8 revision;
 	u8 vid_value;
 	u8 beep_pin;
+	u8 internal;	/* Internal sensors can be labeled */
 	/* Features skipped based on config or DMI */
 	u8 skip_vid;
 	u8 skip_fan;
@@ -1194,6 +1195,22 @@ static ssize_t show_vid_reg(struct device *dev, struct device_attribute *attr,
 }
 static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid_reg, NULL);
 
+static ssize_t show_label(struct device *dev, struct device_attribute *attr,
+		char *buf)
+{
+	static const char *labels[] = {
+		"+5V",
+		"5VSB",
+		"Vbat",
+	};
+	int nr = to_sensor_dev_attr(attr)->index;
+
+	return sprintf(buf, "%s\n", labels[nr]);
+}
+static SENSOR_DEVICE_ATTR(in3_label, S_IRUGO, show_label, NULL, 0);
+static SENSOR_DEVICE_ATTR(in7_label, S_IRUGO, show_label, NULL, 1);
+static SENSOR_DEVICE_ATTR(in8_label, S_IRUGO, show_label, NULL, 2);
+
 static ssize_t show_name(struct device *dev, struct device_attribute
 			 *devattr, char *buf)
 {
@@ -1434,6 +1451,17 @@ static const struct attribute_group it87_group_vid = {
 	.attrs = it87_attributes_vid,
 };
 
+static struct attribute *it87_attributes_label[] = {
+	&sensor_dev_attr_in3_label.dev_attr.attr,
+	&sensor_dev_attr_in7_label.dev_attr.attr,
+	&sensor_dev_attr_in8_label.dev_attr.attr,
+	NULL
+};
+
+static const struct attribute_group it87_group_label = {
+	.attrs = it87_attributes_vid,
+};
+
 /* SuperIO detection - will change isa_address if a chip is found */
 static int __init it87_find(unsigned short *address,
 	struct it87_sio_data *sio_data)
@@ -1487,6 +1515,9 @@ static int __init it87_find(unsigned short *address,
 	pr_info("it87: Found IT%04xF chip at 0x%x, revision %d\n",
 		chip_type, *address, sio_data->revision);
 
+	/* in8 (Vbat) is always internal */
+	sio_data->internal = (1 << 2);
+
 	/* Read GPIO config and VID value from LDN 7 (GPIO) */
 	if (sio_data->type == it87) {
 		/* The IT8705F doesn't have VID pins at all */
@@ -1540,9 +1571,9 @@ static int __init it87_find(unsigned short *address,
 			pr_notice("it87: Routing internal VCCH to in7\n");
 		}
 		if (reg & (1 << 0))
-			pr_info("it87: in3 is VCC (+5V)\n");
+			sio_data->internal |= (1 << 0);
 		if (reg & (1 << 1))
-			pr_info("it87: in7 is VCCH (+5V Stand-By)\n");
+			sio_data->internal |= (1 << 1);
 
 		sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
 	}
@@ -1600,6 +1631,7 @@ static void it87_remove_files(struct device *dev)
 	}
 	if (!sio_data->skip_vid)
 		sysfs_remove_group(&dev->kobj, &it87_group_vid);
+	sysfs_remove_group(&dev->kobj, &it87_group_label);
 }
 
 static int __devinit it87_probe(struct platform_device *pdev)
@@ -1725,6 +1757,16 @@ static int __devinit it87_probe(struct platform_device *pdev)
 			goto ERROR4;
 	}
 
+	/* Export labels for internal sensors */
+	for (i = 0; i < 3; i++) {
+		if (!(sio_data->internal & (1 << i)))
+			continue;
+		err = sysfs_create_file(&dev->kobj,
+					it87_attributes_label[i]);
+		if (err)
+			goto ERROR4;
+	}
+
 	data->hwmon_dev = hwmon_device_register(dev);
 	if (IS_ERR(data->hwmon_dev)) {
 		err = PTR_ERR(data->hwmon_dev);

drivers/hwmon/k8temp.c

@@ -252,12 +252,13 @@ static int __devinit k8temp_probe(struct pci_dev *pdev,
 				   &sensor_dev_attr_temp3_input.dev_attr);
 		if (err)
 			goto exit_remove;
-		if (data->sensorsp & SEL_PLACE)
+		if (data->sensorsp & SEL_PLACE) {
 			err = device_create_file(&pdev->dev,
 					   &sensor_dev_attr_temp4_input.
 					   dev_attr);
 			if (err)
 				goto exit_remove;
+		}
 	}
 
 	err = device_create_file(&pdev->dev, &dev_attr_name);

drivers/hwmon/lm75.c

@@ -280,10 +280,49 @@ static int lm75_detect(struct i2c_client *new_client,
 	return 0;
 }
 
+#ifdef CONFIG_PM
+static int lm75_suspend(struct device *dev)
+{
+	int status;
+	struct i2c_client *client = to_i2c_client(dev);
+	status = lm75_read_value(client, LM75_REG_CONF);
+	if (status < 0) {
+		dev_dbg(&client->dev, "Can't read config? %d\n", status);
+		return status;
+	}
+	status = status | LM75_SHUTDOWN;
+	lm75_write_value(client, LM75_REG_CONF, status);
+	return 0;
+}
+
+static int lm75_resume(struct device *dev)
+{
+	int status;
+	struct i2c_client *client = to_i2c_client(dev);
+	status = lm75_read_value(client, LM75_REG_CONF);
+	if (status < 0) {
+		dev_dbg(&client->dev, "Can't read config? %d\n", status);
+		return status;
+	}
+	status = status & ~LM75_SHUTDOWN;
+	lm75_write_value(client, LM75_REG_CONF, status);
+	return 0;
+}
+
+static const struct dev_pm_ops lm75_dev_pm_ops = {
+	.suspend	= lm75_suspend,
+	.resume		= lm75_resume,
+};
+#define LM75_DEV_PM_OPS (&lm75_dev_pm_ops)
+#else
+#define LM75_DEV_PM_OPS NULL
+#endif /* CONFIG_PM */
+
 static struct i2c_driver lm75_driver = {
 	.class		= I2C_CLASS_HWMON,
 	.driver = {
 		.name	= "lm75",
+		.pm	= LM75_DEV_PM_OPS,
 	},
 	.probe		= lm75_probe,
 	.remove		= lm75_remove,

drivers/hwmon/lm75.h

@@ -30,6 +30,7 @@
 /* straight from the datasheet */
 #define LM75_TEMP_MIN (-55000)
 #define LM75_TEMP_MAX 125000
+#define LM75_SHUTDOWN 0x01
 
 /* TEMP: 0.001C/bit (-55C to +125C)
    REG: (0.5C/bit, two's complement) << 7 */

drivers/hwmon/ltc4245.c

@@ -21,6 +21,7 @@
 #include <linux/i2c.h>
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
+#include <linux/i2c/ltc4245.h>
 
 /* Here are names of the chip's registers (a.k.a. commands) */
 enum ltc4245_cmd {
@@ -60,8 +61,72 @@ struct ltc4245_data {
 
 	/* Voltage registers */
 	u8 vregs[0x0d];
+
+	/* GPIO ADC registers */
+	bool use_extra_gpios;
+	int gpios[3];
 };
 
+/*
+ * Update the readings from the GPIO pins. If the driver has been configured to
+ * sample all GPIO's as analog voltages, a round-robin sampling method is used.
+ * Otherwise, only the configured GPIO pin is sampled.
+ *
+ * LOCKING: must hold data->update_lock
+ */
+static void ltc4245_update_gpios(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct ltc4245_data *data = i2c_get_clientdata(client);
+	u8 gpio_curr, gpio_next, gpio_reg;
+	int i;
+
+	/* no extra gpio support, we're basically done */
+	if (!data->use_extra_gpios) {
+		data->gpios[0] = data->vregs[LTC4245_GPIOADC - 0x10];
+		return;
+	}
+
+	/*
+	 * If the last reading was too long ago, then we mark all old GPIO
+	 * readings as stale by setting them to -EAGAIN
+	 */
+	if (time_after(jiffies, data->last_updated + 5 * HZ)) {
+		dev_dbg(&client->dev, "Marking GPIOs invalid\n");
+		for (i = 0; i < ARRAY_SIZE(data->gpios); i++)
+			data->gpios[i] = -EAGAIN;
+	}
+
+	/*
+	 * Get the current GPIO pin
+	 *
+	 * The datasheet calls these GPIO[1-3], but we'll calculate the zero
+	 * based array index instead, and call them GPIO[0-2]. This is much
+	 * easier to think about.
+	 */
+	gpio_curr = (data->cregs[LTC4245_GPIO] & 0xc0) >> 6;
+	if (gpio_curr > 0)
+		gpio_curr -= 1;
+
+	/* Read the GPIO voltage from the GPIOADC register */
+	data->gpios[gpio_curr] = data->vregs[LTC4245_GPIOADC - 0x10];
+
+	/* Find the next GPIO pin to read */
+	gpio_next = (gpio_curr + 1) % ARRAY_SIZE(data->gpios);
+
+	/*
+	 * Calculate the correct setting for the GPIO register so it will
+	 * sample the next GPIO pin
+	 */
+	gpio_reg = (data->cregs[LTC4245_GPIO] & 0x3f) | ((gpio_next + 1) << 6);
+
+	/* Update the GPIO register */
+	i2c_smbus_write_byte_data(client, LTC4245_GPIO, gpio_reg);
+
+	/* Update saved data */
+	data->cregs[LTC4245_GPIO] = gpio_reg;
+}
+
 static struct ltc4245_data *ltc4245_update_device(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
@@ -93,6 +158,9 @@ static struct ltc4245_data *ltc4245_update_device(struct device *dev)
 				data->vregs[i] = val;
 		}
 
+		/* Update GPIO readings */
+		ltc4245_update_gpios(dev);
+
 		data->last_updated = jiffies;
 		data->valid = 1;
 	}
@@ -233,6 +301,22 @@ static ssize_t ltc4245_show_alarm(struct device *dev,
 	return snprintf(buf, PAGE_SIZE, "%u\n", (reg & mask) ? 1 : 0);
 }
 
+static ssize_t ltc4245_show_gpio(struct device *dev,
+				 struct device_attribute *da,
+				 char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct ltc4245_data *data = ltc4245_update_device(dev);
+	int val = data->gpios[attr->index];
+
+	/* handle stale GPIO's */
+	if (val < 0)
+		return val;
+
+	/* Convert to millivolts and print */
+	return snprintf(buf, PAGE_SIZE, "%u\n", val * 10);
+}
+
 /* These macros are used below in constructing device attribute objects
  * for use with sysfs_create_group() to make a sysfs device file
  * for each register.
@@ -254,6 +338,10 @@ static ssize_t ltc4245_show_alarm(struct device *dev,
 	static SENSOR_DEVICE_ATTR_2(name, S_IRUGO, \
 	ltc4245_show_alarm, NULL, (mask), reg)
 
+#define LTC4245_GPIO_VOLTAGE(name, gpio_num) \
+	static SENSOR_DEVICE_ATTR(name, S_IRUGO, \
+	ltc4245_show_gpio, NULL, gpio_num)
+
 /* Construct a sensor_device_attribute structure for each register */
 
 /* Input voltages */
@@ -293,7 +381,9 @@ LTC4245_ALARM(in7_min_alarm,	(1 << 2),	LTC4245_FAULT2);
 LTC4245_ALARM(in8_min_alarm,	(1 << 3),	LTC4245_FAULT2);
 
 /* GPIO voltages */
-LTC4245_VOLTAGE(in9_input,			LTC4245_GPIOADC);
+LTC4245_GPIO_VOLTAGE(in9_input,			0);
+LTC4245_GPIO_VOLTAGE(in10_input,		1);
+LTC4245_GPIO_VOLTAGE(in11_input,		2);
 
 /* Power Consumption (virtual) */
 LTC4245_POWER(power1_input,			LTC4245_12VSENSE);
@@ -304,7 +394,7 @@ LTC4245_POWER(power4_input,			LTC4245_VEESENSE);
 /* Finally, construct an array of pointers to members of the above objects,
  * as required for sysfs_create_group()
  */
-static struct attribute *ltc4245_attributes[] = {
+static struct attribute *ltc4245_std_attributes[] = {
 	&sensor_dev_attr_in1_input.dev_attr.attr,
 	&sensor_dev_attr_in2_input.dev_attr.attr,
 	&sensor_dev_attr_in3_input.dev_attr.attr,
@@ -345,10 +435,77 @@ static struct attribute *ltc4245_attributes[] = {
 	NULL,
 };
 
-static const struct attribute_group ltc4245_group = {
-	.attrs = ltc4245_attributes,
+static struct attribute *ltc4245_gpio_attributes[] = {
+	&sensor_dev_attr_in10_input.dev_attr.attr,
+	&sensor_dev_attr_in11_input.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group ltc4245_std_group = {
+	.attrs = ltc4245_std_attributes,
+};
+
+static const struct attribute_group ltc4245_gpio_group = {
+	.attrs = ltc4245_gpio_attributes,
 };
 
+static int ltc4245_sysfs_create_groups(struct i2c_client *client)
+{
+	struct ltc4245_data *data = i2c_get_clientdata(client);
+	struct device *dev = &client->dev;
+	int ret;
+
+	/* register the standard sysfs attributes */
+	ret = sysfs_create_group(&dev->kobj, &ltc4245_std_group);
+	if (ret) {
+		dev_err(dev, "unable to register standard attributes\n");
+		return ret;
+	}
+
+	/* if we're using the extra gpio support, register it's attributes */
+	if (data->use_extra_gpios) {
+		ret = sysfs_create_group(&dev->kobj, &ltc4245_gpio_group);
+		if (ret) {
+			dev_err(dev, "unable to register gpio attributes\n");
+			sysfs_remove_group(&dev->kobj, &ltc4245_std_group);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static void ltc4245_sysfs_remove_groups(struct i2c_client *client)
+{
+	struct ltc4245_data *data = i2c_get_clientdata(client);
+	struct device *dev = &client->dev;
+
+	if (data->use_extra_gpios)
+		sysfs_remove_group(&dev->kobj, &ltc4245_gpio_group);
+
+	sysfs_remove_group(&dev->kobj, &ltc4245_std_group);
+}
+
+static bool ltc4245_use_extra_gpios(struct i2c_client *client)
+{
+	struct ltc4245_platform_data *pdata = dev_get_platdata(&client->dev);
+#ifdef CONFIG_OF
+	struct device_node *np = client->dev.of_node;
+#endif
+
+	/* prefer platform data */
+	if (pdata)
+		return pdata->use_extra_gpios;
+
+#ifdef CONFIG_OF
+	/* fallback on OF */
+	if (of_find_property(np, "ltc4245,use-extra-gpios", NULL))
+		return true;
+#endif
+
+	return false;
+}
+
 static int ltc4245_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
@@ -367,15 +524,16 @@ static int ltc4245_probe(struct i2c_client *client,
 
 	i2c_set_clientdata(client, data);
 	mutex_init(&data->update_lock);
+	data->use_extra_gpios = ltc4245_use_extra_gpios(client);
 
 	/* Initialize the LTC4245 chip */
 	i2c_smbus_write_byte_data(client, LTC4245_FAULT1, 0x00);
 	i2c_smbus_write_byte_data(client, LTC4245_FAULT2, 0x00);
 
 	/* Register sysfs hooks */
-	ret = sysfs_create_group(&client->dev.kobj, &ltc4245_group);
+	ret = ltc4245_sysfs_create_groups(client);
 	if (ret)
-		goto out_sysfs_create_group;
+		goto out_sysfs_create_groups;
 
 	data->hwmon_dev = hwmon_device_register(&client->dev);
 	if (IS_ERR(data->hwmon_dev)) {
@@ -386,8 +544,8 @@ static int ltc4245_probe(struct i2c_client *client,
 	return 0;
 
 out_hwmon_device_register:
-	sysfs_remove_group(&client->dev.kobj, &ltc4245_group);
-out_sysfs_create_group:
+	ltc4245_sysfs_remove_groups(client);
+out_sysfs_create_groups:
 	kfree(data);
 out_kzalloc:
 	return ret;
@@ -398,8 +556,7 @@ static int ltc4245_remove(struct i2c_client *client)
 	struct ltc4245_data *data = i2c_get_clientdata(client);
 
 	hwmon_device_unregister(data->hwmon_dev);
-	sysfs_remove_group(&client->dev.kobj, &ltc4245_group);
-
+	ltc4245_sysfs_remove_groups(client);
 	kfree(data);
 
 	return 0;

drivers/hwmon/pc87360.c

@@ -1610,11 +1610,8 @@ static struct pc87360_data *pc87360_update_device(struct device *dev)
 
 static int __init pc87360_device_add(unsigned short address)
 {
-	struct resource res = {
-		.name	= "pc87360",
-		.flags	= IORESOURCE_IO,
-	};
-	int err, i;
+	struct resource res[3];
+	int err, i, res_count;
 
 	pdev = platform_device_alloc("pc87360", address);
 	if (!pdev) {
@@ -1623,22 +1620,28 @@ static int __init pc87360_device_add(unsigned short address)
 		goto exit;
 	}
 
+	memset(res, 0, 3 * sizeof(struct resource));
+	res_count = 0;
 	for (i = 0; i < 3; i++) {
 		if (!extra_isa[i])
 			continue;
-		res.start = extra_isa[i];
-		res.end = extra_isa[i] + PC87360_EXTENT - 1;
+		res[res_count].start = extra_isa[i];
+		res[res_count].end = extra_isa[i] + PC87360_EXTENT - 1;
+		res[res_count].name = "pc87360",
+		res[res_count].flags = IORESOURCE_IO,
 
-		err = acpi_check_resource_conflict(&res);
+		err = acpi_check_resource_conflict(&res[res_count]);
 		if (err)
 			goto exit_device_put;
 
-		err = platform_device_add_resources(pdev, &res, 1);
-		if (err) {
-			printk(KERN_ERR "pc87360: Device resource[%d] "
-			       "addition failed (%d)\n", i, err);
-			goto exit_device_put;
-		}
+		res_count++;
+	}
+
+	err = platform_device_add_resources(pdev, res, res_count);
+	if (err) {
+		printk(KERN_ERR "pc87360: Device resources addition failed "
+		       "(%d)\n", err);
+		goto exit_device_put;
 	}
 
 	err = platform_device_add(pdev);

drivers/hwmon/via-cputemp.c

@@ -39,7 +39,7 @@
 
 #define DRVNAME	"via_cputemp"
 
-enum { SHOW_TEMP, SHOW_LABEL, SHOW_NAME } SHOW;
+enum { SHOW_TEMP, SHOW_LABEL, SHOW_NAME };
 
 /*
  * Functions declaration

drivers/hwmon/w83627ehf.c

@@ -39,6 +39,7 @@
     w83627dhg    9      5       4       3      0xa020 0xc1    0x5ca3
     w83627dhg-p  9      5       4       3      0xb070 0xc1    0x5ca3
     w83667hg     9      5       3       3      0xa510 0xc1    0x5ca3
+    w83667hg-b   9      5       3       3      0xb350 0xc1    0x5ca3
 */
 
 #include <linux/module.h>
@@ -55,7 +56,7 @@
 #include <linux/io.h>
 #include "lm75.h"
 
-enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg };
+enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg, w83667hg_b };
 
 /* used to set data->name = w83627ehf_device_names[data->sio_kind] */
 static const char * w83627ehf_device_names[] = {
@@ -63,6 +64,7 @@ static const char * w83627ehf_device_names[] = {
 	"w83627dhg",
 	"w83627dhg",
 	"w83667hg",
+	"w83667hg",
 };
 
 static unsigned short force_id;
@@ -91,6 +93,7 @@ MODULE_PARM_DESC(force_id, "Override the detected device ID");
 #define SIO_W83627DHG_ID	0xa020
 #define SIO_W83627DHG_P_ID	0xb070
 #define SIO_W83667HG_ID 	0xa510
+#define SIO_W83667HG_B_ID	0xb350
 #define SIO_ID_MASK		0xFFF0
 
 static inline void
@@ -201,8 +204,14 @@ static const u8 W83627EHF_REG_TOLERANCE[] = { 0x07, 0x07, 0x14, 0x62 };
 static const u8 W83627EHF_REG_FAN_START_OUTPUT[] = { 0x0a, 0x0b, 0x16, 0x65 };
 static const u8 W83627EHF_REG_FAN_STOP_OUTPUT[] = { 0x08, 0x09, 0x15, 0x64 };
 static const u8 W83627EHF_REG_FAN_STOP_TIME[] = { 0x0c, 0x0d, 0x17, 0x66 };
-static const u8 W83627EHF_REG_FAN_MAX_OUTPUT[] = { 0xff, 0x67, 0xff, 0x69 };
-static const u8 W83627EHF_REG_FAN_STEP_OUTPUT[] = { 0xff, 0x68, 0xff, 0x6a };
+
+static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_COMMON[]
+						= { 0xff, 0x67, 0xff, 0x69 };
+static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_COMMON[]
+						= { 0xff, 0x68, 0xff, 0x6a };
+
+static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B[] = { 0x67, 0x69, 0x6b };
+static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B[] = { 0x68, 0x6a, 0x6c };
 
 /*
  * Conversions
@@ -277,6 +286,11 @@ struct w83627ehf_data {
 	struct device *hwmon_dev;
 	struct mutex lock;
 
+	const u8 *REG_FAN_START_OUTPUT;
+	const u8 *REG_FAN_STOP_OUTPUT;
+	const u8 *REG_FAN_MAX_OUTPUT;
+	const u8 *REG_FAN_STEP_OUTPUT;
+
 	struct mutex update_lock;
 	char valid;		/* !=0 if following fields are valid */
 	unsigned long last_updated;	/* In jiffies */
@@ -524,7 +538,10 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 			}
 		}
 
-		for (i = 0; i < 4; i++) {
+		for (i = 0; i < data->pwm_num; i++) {
+			if (!(data->has_fan & (1 << i)))
+				continue;
+
 			/* pwmcfg, tolerance mapped for i=0, i=1 to same reg */
 			if (i != 1) {
 				pwmcfg = w83627ehf_read_value(data,
@@ -546,6 +563,17 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 						W83627EHF_REG_FAN_STOP_OUTPUT[i]);
 			data->fan_stop_time[i] = w83627ehf_read_value(data,
 						W83627EHF_REG_FAN_STOP_TIME[i]);
+
+			if (data->REG_FAN_MAX_OUTPUT[i] != 0xff)
+				data->fan_max_output[i] =
+				  w83627ehf_read_value(data,
+					       data->REG_FAN_MAX_OUTPUT[i]);
+
+			if (data->REG_FAN_STEP_OUTPUT[i] != 0xff)
+				data->fan_step_output[i] =
+				  w83627ehf_read_value(data,
+					       data->REG_FAN_STEP_OUTPUT[i]);
+
 			data->target_temp[i] =
 				w83627ehf_read_value(data,
 					W83627EHF_REG_TARGET[i]) &
@@ -1126,7 +1154,7 @@ store_##reg(struct device *dev, struct device_attribute *attr, \
 	u32 val = SENSORS_LIMIT(simple_strtoul(buf, NULL, 10), 1, 255); \
 	mutex_lock(&data->update_lock); \
 	data->reg[nr] = val; \
-	w83627ehf_write_value(data, W83627EHF_REG_##REG[nr], val); \
+	w83627ehf_write_value(data, data->REG_##REG[nr], val); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
 }
@@ -1206,12 +1234,26 @@ static struct sensor_device_attribute sda_sf3_arrays[] = {
 		    store_fan_stop_output, 1),
 	SENSOR_ATTR(pwm3_stop_output, S_IWUSR | S_IRUGO, show_fan_stop_output,
 		    store_fan_stop_output, 2),
+};
 
-	/* pwm1 and pwm3 don't support max and step settings */
+
+/*
+ * pwm1 and pwm3 don't support max and step settings on all chips.
+ * Need to check support while generating/removing attribute files.
+ */
+static struct sensor_device_attribute sda_sf3_max_step_arrays[] = {
+	SENSOR_ATTR(pwm1_max_output, S_IWUSR | S_IRUGO, show_fan_max_output,
+		    store_fan_max_output, 0),
+	SENSOR_ATTR(pwm1_step_output, S_IWUSR | S_IRUGO, show_fan_step_output,
+		    store_fan_step_output, 0),
 	SENSOR_ATTR(pwm2_max_output, S_IWUSR | S_IRUGO, show_fan_max_output,
 		    store_fan_max_output, 1),
 	SENSOR_ATTR(pwm2_step_output, S_IWUSR | S_IRUGO, show_fan_step_output,
 		    store_fan_step_output, 1),
+	SENSOR_ATTR(pwm3_max_output, S_IWUSR | S_IRUGO, show_fan_max_output,
+		    store_fan_max_output, 2),
+	SENSOR_ATTR(pwm3_step_output, S_IWUSR | S_IRUGO, show_fan_step_output,
+		    store_fan_step_output, 2),
 };
 
 static ssize_t
@@ -1235,6 +1277,12 @@ static void w83627ehf_device_remove_files(struct device *dev)
 
 	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays); i++)
 		device_remove_file(dev, &sda_sf3_arrays[i].dev_attr);
+	for (i = 0; i < ARRAY_SIZE(sda_sf3_max_step_arrays); i++) {
+		struct sensor_device_attribute *attr =
+		  &sda_sf3_max_step_arrays[i];
+		if (data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff)
+			device_remove_file(dev, &attr->dev_attr);
+	}
 	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++)
 		device_remove_file(dev, &sda_sf3_arrays_fan4[i].dev_attr);
 	for (i = 0; i < data->in_num; i++) {
@@ -1343,22 +1391,37 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 	/* 627EHG and 627EHF have 10 voltage inputs; 627DHG and 667HG have 9 */
 	data->in_num = (sio_data->kind == w83627ehf) ? 10 : 9;
 	/* 667HG has 3 pwms */
-	data->pwm_num = (sio_data->kind == w83667hg) ? 3 : 4;
+	data->pwm_num = (sio_data->kind == w83667hg
+			 || sio_data->kind == w83667hg_b) ? 3 : 4;
 
 	/* Check temp3 configuration bit for 667HG */
-	if (sio_data->kind == w83667hg) {
+	if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
 		data->temp3_disable = w83627ehf_read_value(data,
 					W83627EHF_REG_TEMP_CONFIG[1]) & 0x01;
 		data->in6_skip = !data->temp3_disable;
 	}
 
+	data->REG_FAN_START_OUTPUT = W83627EHF_REG_FAN_START_OUTPUT;
+	data->REG_FAN_STOP_OUTPUT = W83627EHF_REG_FAN_STOP_OUTPUT;
+	if (sio_data->kind == w83667hg_b) {
+		data->REG_FAN_MAX_OUTPUT =
+		  W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B;
+		data->REG_FAN_STEP_OUTPUT =
+		  W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B;
+	} else {
+		data->REG_FAN_MAX_OUTPUT =
+		  W83627EHF_REG_FAN_MAX_OUTPUT_COMMON;
+		data->REG_FAN_STEP_OUTPUT =
+		  W83627EHF_REG_FAN_STEP_OUTPUT_COMMON;
+	}
+
 	/* Initialize the chip */
 	w83627ehf_init_device(data);
 
 	data->vrm = vid_which_vrm();
 	superio_enter(sio_data->sioreg);
 	/* Read VID value */
-	if (sio_data->kind == w83667hg) {
+	if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
 		/* W83667HG has different pins for VID input and output, so
 		we can get the VID input values directly at logical device D
 		0xe3. */
@@ -1409,7 +1472,7 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 	}
 
 	/* fan4 and fan5 share some pins with the GPIO and serial flash */
-	if (sio_data->kind == w83667hg) {
+	if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
 		fan5pin = superio_inb(sio_data->sioreg, 0x27) & 0x20;
 		fan4pin = superio_inb(sio_data->sioreg, 0x27) & 0x40;
 	} else {
@@ -1440,6 +1503,15 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 			&sda_sf3_arrays[i].dev_attr)))
 			goto exit_remove;
 
+	for (i = 0; i < ARRAY_SIZE(sda_sf3_max_step_arrays); i++) {
+		struct sensor_device_attribute *attr =
+		  &sda_sf3_max_step_arrays[i];
+		if (data->REG_FAN_STEP_OUTPUT[attr->index] != 0xff) {
+			err = device_create_file(dev, &attr->dev_attr);
+			if (err)
+				goto exit_remove;
+		}
+	}
 	/* if fan4 is enabled create the sf3 files for it */
 	if ((data->has_fan & (1 << 3)) && data->pwm_num >= 4)
 		for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++) {
@@ -1556,6 +1628,7 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 	static const char __initdata sio_name_W83627DHG[] = "W83627DHG";
 	static const char __initdata sio_name_W83627DHG_P[] = "W83627DHG-P";
 	static const char __initdata sio_name_W83667HG[] = "W83667HG";
+	static const char __initdata sio_name_W83667HG_B[] = "W83667HG-B";
 
 	u16 val;
 	const char *sio_name;
@@ -1588,6 +1661,10 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
 		sio_data->kind = w83667hg;
 		sio_name = sio_name_W83667HG;
 		break;
+	case SIO_W83667HG_B_ID:
+		sio_data->kind = w83667hg_b;
+		sio_name = sio_name_W83667HG_B;
+		break;
 	default:
 		if (val != 0xffff)
 			pr_debug(DRVNAME ": unsupported chip ID: 0x%04x\n",

include/linux/i2c/ltc4245.h

+/*
+ * Platform Data for LTC4245 hardware monitor chip
+ *
+ * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#ifndef LINUX_LTC4245_H
+#define LINUX_LTC4245_H
+
+#include <linux/types.h>
+
+struct ltc4245_platform_data {
+	bool use_extra_gpios;
+};
+
+#endif /* LINUX_LTC4245_H */