[BNX2]: speedup serdes linkup

This speeds up link-up time on 5706 SerDes if the link partner does
not autoneg, a rather common scenario in blade servers. Some blade
servers use IPMI for keyboard input and it's important to minimize
link disruptions.

The speedup is achieved by shortening the timer to (HZ / 3) during
the transient period right after initiating a SerDes autoneg. If
autoneg does not complete, parallel detect can be done sooner. After
the transient period is over, the timer goes back to its normal HZ
interval.

As suggested by Jeff Garzik, the timer initialization is moved to
bnx2_init_board() from bnx2_open().

An eeprom bit is also added to allow default forced SerDes speed for
even faster link-up time.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/bnx2.c

@@ -806,7 +806,19 @@ bnx2_setup_serdes_phy(struct bnx2 *bp)
 		bnx2_write_phy(bp, MII_ADVERTISE, new_adv);
 		bnx2_write_phy(bp, MII_BMCR, bmcr | BMCR_ANRESTART |
 			BMCR_ANENABLE);
-		bp->serdes_an_pending = SERDES_AN_TIMEOUT / bp->timer_interval;
+		if (CHIP_NUM(bp) == CHIP_NUM_5706) {
+			/* Speed up link-up time when the link partner
+			 * does not autonegotiate which is very common
+			 * in blade servers. Some blade servers use
+			 * IPMI for kerboard input and it's important
+			 * to minimize link disruptions. Autoneg. involves
+			 * exchanging base pages plus 3 next pages and
+			 * normally completes in about 120 msec.
+			 */
+			bp->current_interval = SERDES_AN_TIMEOUT;
+			bp->serdes_an_pending = 1;
+			mod_timer(&bp->timer, jiffies + bp->current_interval);
+		}
 	}
 
 	return 0;
@@ -3800,6 +3812,9 @@ bnx2_timer(unsigned long data)
 	struct bnx2 *bp = (struct bnx2 *) data;
 	u32 msg;
 
+	if (!netif_running(bp->dev))
+		return;
+
 	if (atomic_read(&bp->intr_sem) != 0)
 		goto bnx2_restart_timer;
 
@@ -3817,6 +3832,8 @@ bnx2_timer(unsigned long data)
 		else if ((bp->link_up == 0) && (bp->autoneg & AUTONEG_SPEED)) {
 			u32 bmcr;
 
+			bp->current_interval = bp->timer_interval;
+
 			bnx2_read_phy(bp, MII_BMCR, &bmcr);
 
 			if (bmcr & BMCR_ANENABLE) {
@@ -3859,14 +3876,14 @@ bnx2_timer(unsigned long data)
 
 			}
 		}
+		else
+			bp->current_interval = bp->timer_interval;
 
 		spin_unlock_irqrestore(&bp->phy_lock, flags);
 	}
 
 bnx2_restart_timer:
-	bp->timer.expires = RUN_AT(bp->timer_interval);
-
-	add_timer(&bp->timer);
+	mod_timer(&bp->timer, jiffies + bp->current_interval);
 }
 
 /* Called with rtnl_lock */
@@ -3919,12 +3936,7 @@ bnx2_open(struct net_device *dev)
 		return rc;
 	}
 	
-	init_timer(&bp->timer);
-
-	bp->timer.expires = RUN_AT(bp->timer_interval);
-	bp->timer.data = (unsigned long) bp;
-	bp->timer.function = bnx2_timer;
-	add_timer(&bp->timer);
+	mod_timer(&bp->timer, jiffies + bp->current_interval);
 
 	atomic_set(&bp->intr_sem, 0);
 
@@ -4485,8 +4497,9 @@ bnx2_nway_reset(struct net_device *dev)
 
 		spin_lock_irq(&bp->phy_lock);
 		if (CHIP_NUM(bp) == CHIP_NUM_5706) {
-			bp->serdes_an_pending = SERDES_AN_TIMEOUT /
-				bp->timer_interval;
+			bp->current_interval = SERDES_AN_TIMEOUT;
+			bp->serdes_an_pending = 1;
+			mod_timer(&bp->timer, jiffies + bp->current_interval);
 		}
 	}
 
@@ -5315,6 +5328,7 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
 	bp->stats_ticks = 1000000 & 0xffff00;
 
 	bp->timer_interval =  HZ;
+	bp->current_interval =  HZ;
 
 	/* Disable WOL support if we are running on a SERDES chip. */
 	if (CHIP_BOND_ID(bp) & CHIP_BOND_ID_SERDES_BIT) {
@@ -5338,6 +5352,15 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
 	bp->req_line_speed = 0;
 	if (bp->phy_flags & PHY_SERDES_FLAG) {
 		bp->advertising = ETHTOOL_ALL_FIBRE_SPEED | ADVERTISED_Autoneg;
+
+		reg = REG_RD_IND(bp, HOST_VIEW_SHMEM_BASE +
+				 BNX2_PORT_HW_CFG_CONFIG);
+		reg &= BNX2_PORT_HW_CFG_CFG_DFLT_LINK_MASK;
+		if (reg == BNX2_PORT_HW_CFG_CFG_DFLT_LINK_1G) {
+			bp->autoneg = 0;
+			bp->req_line_speed = bp->line_speed = SPEED_1000;
+			bp->req_duplex = DUPLEX_FULL;
+		}
 	}
 	else {
 		bp->advertising = ETHTOOL_ALL_COPPER_SPEED | ADVERTISED_Autoneg;
@@ -5345,6 +5368,11 @@ bnx2_init_board(struct pci_dev *pdev, struct net_device *dev)
 
 	bp->req_flow_ctrl = FLOW_CTRL_RX | FLOW_CTRL_TX;
 
+	init_timer(&bp->timer);
+	bp->timer.expires = RUN_AT(bp->timer_interval);
+	bp->timer.data = (unsigned long) bp;
+	bp->timer.function = bnx2_timer;
+
 	return 0;
 
 err_out_unmap:

drivers/net/bnx2.h

@@ -3872,6 +3872,7 @@ struct bnx2 {
 	char			*name;
 
 	int			timer_interval;
+	int			current_interval;
 	struct			timer_list timer;
 	struct work_struct	reset_task;
 	int			in_reset_task;
@@ -3986,7 +3987,7 @@ struct bnx2 {
 #define PHY_LOOPBACK		2
 
 	u8			serdes_an_pending;
-#define SERDES_AN_TIMEOUT	(2 * HZ)
+#define SERDES_AN_TIMEOUT	(HZ / 3)
 
 	u8			mac_addr[8];
 
@@ -4172,6 +4173,9 @@ struct fw_info {
 
 #define BNX2_PORT_HW_CFG_MAC_LOWER		0x00000054
 #define BNX2_PORT_HW_CFG_CONFIG			0x00000058
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_MASK	 0x001f0000
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_AN	 0x00000000
+#define BNX2_PORT_HW_CFG_CFG_DFLT_LINK_1G	 0x00030000
 
 #define BNX2_PORT_HW_CFG_IMD_MAC_A_UPPER	0x00000068
 #define BNX2_PORT_HW_CFG_IMD_MAC_A_LOWER	0x0000006c