m68knommu: remove RPXCLASSIC from the m68k tree

This ifdefs are leftovers from the time as the driver was running
on a ppc.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

drivers/net/fec.c

@@ -43,17 +43,9 @@
 #include <asm/pgtable.h>
 #include <asm/cacheflush.h>
 
-#if defined(CONFIG_M523x) || defined(CONFIG_M527x) || \
-    defined(CONFIG_M5272) || defined(CONFIG_M528x) || \
-    defined(CONFIG_M520x) || defined(CONFIG_M532x)
 #include <asm/coldfire.h>
 #include <asm/mcfsim.h>
 #include "fec.h"
-#else
-#include <asm/8xx_immap.h>
-#include <asm/mpc8xx.h>
-#include "commproc.h"
-#endif
 
 #if defined(CONFIG_FEC2)
 #define	FEC_MAX_PORTS	2
@@ -1229,14 +1221,9 @@ static phy_info_t const * const phy_info[] = {
 
 /* ------------------------------------------------------------------------- */
 #ifdef HAVE_mii_link_interrupt
-#ifdef CONFIG_RPXCLASSIC
-static void
-mii_link_interrupt(void *dev_id);
-#else
 static irqreturn_t
 mii_link_interrupt(int irq, void * dev_id);
 #endif
-#endif
 
 #if defined(CONFIG_M5272)
 /*
@@ -1789,20 +1776,6 @@ static void __inline__ fec_request_intrs(struct net_device *dev)
 
 	if (request_8xxirq(FEC_INTERRUPT, fec_enet_interrupt, 0, "fec", dev) != 0)
 		panic("Could not allocate FEC IRQ!");
-
-#ifdef CONFIG_RPXCLASSIC
-	/* Make Port C, bit 15 an input that causes interrupts.
-	*/
-	immap->im_ioport.iop_pcpar &= ~0x0001;
-	immap->im_ioport.iop_pcdir &= ~0x0001;
-	immap->im_ioport.iop_pcso &= ~0x0001;
-	immap->im_ioport.iop_pcint |= 0x0001;
-	cpm_install_handler(CPMVEC_PIO_PC15, mii_link_interrupt, dev);
-
-	/* Make LEDS reflect Link status.
-	*/
-	*((uint *) RPX_CSR_ADDR) &= ~BCSR2_FETHLEDMODE;
-#endif
 }
 
 static void __inline__ fec_get_mac(struct net_device *dev)
@@ -1811,16 +1784,6 @@ static void __inline__ fec_get_mac(struct net_device *dev)
 
 	bd = (bd_t *)__res;
 	memcpy(dev->dev_addr, bd->bi_enetaddr, ETH_ALEN);
-
-#ifdef CONFIG_RPXCLASSIC
-	/* The Embedded Planet boards have only one MAC address in
-	 * the EEPROM, but can have two Ethernet ports.  For the
-	 * FEC port, we create another address by setting one of
-	 * the address bits above something that would have (up to
-	 * now) been allocated.
-	 */
-	dev->dev_adrd[3] |= 0x80;
-#endif
 }
 
 static void __inline__ fec_set_mii(struct net_device *dev, struct fec_enet_private *fep)
@@ -2099,13 +2062,8 @@ mii_discover_phy(uint mii_reg, struct net_device *dev)
 /* This interrupt occurs when the PHY detects a link change.
 */
 #ifdef HAVE_mii_link_interrupt
-#ifdef CONFIG_RPXCLASSIC
-static void
-mii_link_interrupt(void *dev_id)
-#else
 static irqreturn_t
 mii_link_interrupt(int irq, void * dev_id)
-#endif
 {
 	struct	net_device *dev = dev_id;
 	struct fec_enet_private *fep = netdev_priv(dev);

include/asm-m68knommu/commproc.h

@@ -519,25 +519,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00002c00)
 #endif
 
-#ifdef CONFIG_RPXCLASSIC
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD	((ushort)0x0001)
-#define PA_ENET_TXD	((ushort)0x0002)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PB_ENET_TENA	((uint)0x00001000)
-#define PC_ENET_CLSN	((ushort)0x0010)
-#define PC_ENET_RENA	((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK	((uint)0x000000ff)
-#define SICR_ENET_CLKRT	((uint)0x0000003d)
-#endif
-
 /* SCC Event register as used by Ethernet.
 */
 #define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */