brcmfmac: fix sdio suspend and resume

commit 330b4e4b ("brcmfmac: Add wowl support for SDIO devices.")
changed the behaviour by removing the MMC_PM_KEEP_POWER flag for
non-wowl scenario, which needs to be restored. Another necessary
change is to mark the card as being non-removable. With this in place
the suspend resume test passes successfully doing:

 # echo devices > /sys/power/pm_test
 # echo mem > /sys/power/state

Note that power may still be switched off when system is going
in S3 state.
Reported-by: NFu, Zhonghui <&lt;zhonghui.fu@linux.intel.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c

@@ -1011,6 +1011,14 @@ static int brcmf_sdiod_remove(struct brcmf_sdio_dev *sdiodev)
 	return 0;
 }
 
+static void brcmf_sdiod_host_fixup(struct mmc_host *host)
+{
+	/* runtime-pm powers off the device */
+	pm_runtime_forbid(host->parent);
+	/* avoid removal detection upon resume */
+	host->caps |= MMC_CAP_NONREMOVABLE;
+}
+
 static int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev)
 {
 	struct sdio_func *func;
@@ -1076,7 +1084,7 @@ static int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev)
 		ret = -ENODEV;
 		goto out;
 	}
-	pm_runtime_forbid(host->parent);
+	brcmf_sdiod_host_fixup(host);
 out:
 	if (ret)
 		brcmf_sdiod_remove(sdiodev);
@@ -1246,15 +1254,15 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
 	brcmf_sdiod_freezer_on(sdiodev);
 	brcmf_sdio_wd_timer(sdiodev->bus, 0);
 
+	sdio_flags = MMC_PM_KEEP_POWER;
 	if (sdiodev->wowl_enabled) {
-		sdio_flags = MMC_PM_KEEP_POWER;
 		if (sdiodev->pdata->oob_irq_supported)
 			enable_irq_wake(sdiodev->pdata->oob_irq_nr);
 		else
-			sdio_flags = MMC_PM_WAKE_SDIO_IRQ;
-		if (sdio_set_host_pm_flags(sdiodev->func[1], sdio_flags))
-			brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
+			sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
 	}
+	if (sdio_set_host_pm_flags(sdiodev->func[1], sdio_flags))
+		brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
 	return 0;
 }