ieee80211: bump IEEE80211_MAX_AMPDU_BUF to support HE

Bump the IEEE80211_MAX_AMPDU_BUF size to 0x100 for HE support
and - for now - use IEEE80211_MAX_AMPDU_BUF_HT everywhere.

This is derived from my internal patch, parts of which Luca
had sent upstream.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

drivers/net/wireless/realtek/rtlwifi/base.c

@@ -1904,7 +1904,7 @@ void rtl_rx_ampdu_apply(struct rtl_priv *rtlpriv)
 		 reject_agg, ctrl_agg_size, agg_size);
 
 	rtlpriv->hw->max_rx_aggregation_subframes =
-		(ctrl_agg_size ? agg_size : IEEE80211_MAX_AMPDU_BUF);
+		(ctrl_agg_size ? agg_size : IEEE80211_MAX_AMPDU_BUF_HT);
 }
 EXPORT_SYMBOL(rtl_rx_ampdu_apply);
 

drivers/staging/rtl8188eu/include/wifi.h

@@ -575,7 +575,6 @@ enum ht_cap_ampdu_factor {
  * According to IEEE802.11n spec size varies from 8K to 64K (in powers of 2)
  */
 #define IEEE80211_MIN_AMPDU_BUF 0x8
-#define IEEE80211_MAX_AMPDU_BUF 0x40
 
 
 #define OP_MODE_PURE                    0

drivers/staging/rtl8712/wifi.h

@@ -574,7 +574,6 @@ struct ieee80211_ht_addt_info {
  * According to IEEE802.11n spec size varies from 8K to 64K (in powers of 2)
  */
 #define IEEE80211_MIN_AMPDU_BUF 0x8
-#define IEEE80211_MAX_AMPDU_BUF 0x40
 
 
 /* Spatial Multiplexing Power Save Modes */

drivers/staging/rtl8723bs/include/wifi.h

@@ -799,7 +799,6 @@ enum HT_CAP_AMPDU_FACTOR {
  * According to IEEE802.11n spec size varies from 8K to 64K (in powers of 2)
  */
 #define IEEE80211_MIN_AMPDU_BUF 0x8
-#define IEEE80211_MAX_AMPDU_BUF 0x40
 
 
 /* Spatial Multiplexing Power Save Modes */

drivers/staging/rtlwifi/base.c

@@ -1838,7 +1838,7 @@ void rtl_rx_ampdu_apply(struct rtl_priv *rtlpriv)
 		 reject_agg, ctrl_agg_size, agg_size);
 
 	rtlpriv->hw->max_rx_aggregation_subframes =
-		(ctrl_agg_size ? agg_size : IEEE80211_MAX_AMPDU_BUF);
+		(ctrl_agg_size ? agg_size : IEEE80211_MAX_AMPDU_BUF_HT);
 }
 
 /*********************************************************

include/linux/ieee80211.h

@@ -1433,11 +1433,13 @@ struct ieee80211_ht_operation {
 #define IEEE80211_DELBA_PARAM_INITIATOR_MASK 0x0800
 
 /*
- * A-PMDU buffer sizes
- * According to IEEE802.11n spec size varies from 8K to 64K (in powers of 2)
+ * A-MPDU buffer sizes
+ * According to HT size varies from 8 to 64 frames
+ * HE adds the ability to have up to 256 frames.
  */
-#define IEEE80211_MIN_AMPDU_BUF 0x8
-#define IEEE80211_MAX_AMPDU_BUF 0x40
+#define IEEE80211_MIN_AMPDU_BUF		0x8
+#define IEEE80211_MAX_AMPDU_BUF_HT	0x40
+#define IEEE80211_MAX_AMPDU_BUF		0x100
 
 
 /* Spatial Multiplexing Power Save Modes (for capability) */

net/mac80211/agg-rx.c

@@ -274,7 +274,7 @@ void ___ieee80211_start_rx_ba_session(struct sta_info *sta,
 	/* XXX: check own ht delayed BA capability?? */
 	if (((ba_policy != 1) &&
 	     (!(sta->sta.ht_cap.cap & IEEE80211_HT_CAP_DELAY_BA))) ||
-	    (buf_size > IEEE80211_MAX_AMPDU_BUF)) {
+	    (buf_size > IEEE80211_MAX_AMPDU_BUF_HT)) {
 		status = WLAN_STATUS_INVALID_QOS_PARAM;
 		ht_dbg_ratelimited(sta->sdata,
 				   "AddBA Req with bad params from %pM on tid %u. policy %d, buffer size %d\n",
@@ -283,7 +283,7 @@ void ___ieee80211_start_rx_ba_session(struct sta_info *sta,
 	}
 	/* determine default buffer size */
 	if (buf_size == 0)
-		buf_size = IEEE80211_MAX_AMPDU_BUF;
+		buf_size = IEEE80211_MAX_AMPDU_BUF_HT;
 
 	/* make sure the size doesn't exceed the maximum supported by the hw */
 	if (buf_size > sta->sta.max_rx_aggregation_subframes)

net/mac80211/agg-tx.c

@@ -514,7 +514,7 @@ void ieee80211_tx_ba_session_handle_start(struct sta_info *sta, int tid)
 	/* send AddBA request */
 	ieee80211_send_addba_request(sdata, sta->sta.addr, tid,
 				     tid_tx->dialog_token, params.ssn,
-				     IEEE80211_MAX_AMPDU_BUF,
+				     IEEE80211_MAX_AMPDU_BUF_HT,
 				     tid_tx->timeout);
 }
 

net/mac80211/ht.c

@@ -352,7 +352,7 @@ void ieee80211_ba_session_work(struct work_struct *work)
 		    test_and_clear_bit(tid,
 				       sta->ampdu_mlme.tid_rx_manage_offl))
 			___ieee80211_start_rx_ba_session(sta, 0, 0, 0, 1, tid,
-							 IEEE80211_MAX_AMPDU_BUF,
+							 IEEE80211_MAX_AMPDU_BUF_HT,
 							 false, true);
 
 		if (test_and_clear_bit(tid + IEEE80211_NUM_TIDS,

net/mac80211/main.c

@@ -597,8 +597,8 @@ struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,
 	local->hw.queues = 1;
 	local->hw.max_rates = 1;
 	local->hw.max_report_rates = 0;
-	local->hw.max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
-	local->hw.max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF;
+	local->hw.max_rx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HT;
+	local->hw.max_tx_aggregation_subframes = IEEE80211_MAX_AMPDU_BUF_HT;
 	local->hw.offchannel_tx_hw_queue = IEEE80211_INVAL_HW_QUEUE;
 	local->hw.conf.long_frame_max_tx_count = wiphy->retry_long;
 	local->hw.conf.short_frame_max_tx_count = wiphy->retry_short;