ARM: OMAP2+: omap_device: call all suspend, resume callbacks when...

ARM: OMAP2+: omap_device: call all suspend, resume callbacks when OMAP_DEVICE_NO_IDLE_ON_SUSPEND is set

During system suspend, when OMAP_DEVICE_NO_IDLE_ON_SUSPEND is set on
an omap_device, call the corresponding driver's ->suspend() and
->suspend_noirq() callbacks (if present).  Similarly, during resume,
the driver's ->resume() and ->resume_noirq() callbacks must both be
called, if present.  (The previous code only called ->suspend_noirq()
and ->resume_noirq().)

If all of these callbacks aren't called, some important driver
suspend/resume code may not get executed.

In current mainline, the bug fixed by this patch is only a problem
under the following conditions:

- the kernel is running on an OMAP4

- an OMAP UART is used as a console

- the kernel command line parameter 'no_console_suspend' is specified

- and the system enters suspend ("echo mem > /sys/power/state").

Under this combined circumstance, the system cannot be awakened via
the serial port after commit be4b0281c
("tty: serial: OMAP: block idle while the UART is transferring data in
PIO mode").  This is because the OMAP UART driver's ->suspend()
callback is never called.  The ->suspend() callback would have called
uart_suspend_port() which in turn would call enable_irq_wake().  Since
enable_irq_wake() isn't called for the UART's IRQ, check_wakeup_irqs()
would mask off the UART IRQ in the GIC.

On v3.3 kernels prior to the above commit, serial resume from suspend
presumably occurred via the PRCM interrupt.  The UART was in
smart-idle mode, so it was able to send a PRCM wakeup which in turn
would be converted into a PRCM interrupt to the GIC, waking up the
kernel.  But after the above commit, when the system is suspended in
the middle of a UART transmit, the UART IP block would be in no-idle
mode.  In no-idle mode, the UART won't generate wakeups to the PRCM
when incoming characters are received; only GIC interrupts.  But since
the UART driver's ->suspend() callback is never called,
uart_suspend_port() and enable_irq_wake() is never called; so the UART
interrupt is masked by check_wakeup_irqs() and the UART can't wake up
the MPU.

The remaining mechanism that could have awakened the system would have
been I/O chain wakeups.  These wouldn't be active because the console
UART's clocks are never disabled when no_console_suspend is used,
preventing the full chip from idling.  Also, current mainline doesn't
yet support full chip idle states for OMAP4, so I/O chain wakeups are
not enabled.

This patch is the result of a collaboration.  John Stultz
<johnstul@us.ibm.com> and Andy Green <andy.green@linaro.org> reported
the serial wakeup problem that led to the discovery of this problem.
Kevin Hilman <khilman@ti.com> narrowed the problem down to the use of
no_console_suspend.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andy Green <andy.green@linaro.org>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

arch/arm/plat-omap/omap_device.c

@@ -754,14 +754,12 @@ static int _od_suspend_noirq(struct device *dev)
 	struct omap_device *od = to_omap_device(pdev);
 	int ret;
 
-	if (od->flags & OMAP_DEVICE_NO_IDLE_ON_SUSPEND)
-		return pm_generic_suspend_noirq(dev);
-
 	ret = pm_generic_suspend_noirq(dev);
 
 	if (!ret && !pm_runtime_status_suspended(dev)) {
 		if (pm_generic_runtime_suspend(dev) == 0) {
-			omap_device_idle(pdev);
+			if (!(od->flags & OMAP_DEVICE_NO_IDLE_ON_SUSPEND))
+				omap_device_idle(pdev);
 			od->flags |= OMAP_DEVICE_SUSPENDED;
 		}
 	}
@@ -774,13 +772,11 @@ static int _od_resume_noirq(struct device *dev)
 	struct platform_device *pdev = to_platform_device(dev);
 	struct omap_device *od = to_omap_device(pdev);
 
-	if (od->flags & OMAP_DEVICE_NO_IDLE_ON_SUSPEND)
-		return pm_generic_resume_noirq(dev);
-
 	if ((od->flags & OMAP_DEVICE_SUSPENDED) &&
 	    !pm_runtime_status_suspended(dev)) {
 		od->flags &= ~OMAP_DEVICE_SUSPENDED;
-		omap_device_enable(pdev);
+		if (!(od->flags & OMAP_DEVICE_NO_IDLE_ON_SUSPEND))
+			omap_device_enable(pdev);
 		pm_generic_runtime_resume(dev);
 	}