qlcnic: Fix LRO disable

o In dev->open LRO was enabled by default, enable it depending
  upon netdev->features , kernel may have disabled it.
o Configure LRO when interface is up.
Signed-off-by: NRajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: NAnirban Chakraborty <Anirban.Chakraborty@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/qlcnic/qlcnic_ethtool.c

@@ -998,22 +998,28 @@ static int qlcnic_set_flags(struct net_device *netdev, u32 data)
 	if (ethtool_invalid_flags(netdev, data, ETH_FLAG_LRO))
 		return -EINVAL;
 
-	if (!(adapter->capabilities & QLCNIC_FW_CAPABILITY_HW_LRO))
-		return -EINVAL;
+	if (data & ETH_FLAG_LRO) {
 
-	if (!adapter->rx_csum) {
-		dev_info(&adapter->pdev->dev, "rx csum is off, "
-			"cannot toggle lro\n");
-		return -EINVAL;
-	}
+		if (netdev->features & NETIF_F_LRO)
+			return 0;
 
-	if ((data & ETH_FLAG_LRO) && (netdev->features & NETIF_F_LRO))
-		return 0;
+		if (!(adapter->capabilities & QLCNIC_FW_CAPABILITY_HW_LRO))
+			return -EINVAL;
+
+		if (!adapter->rx_csum) {
+			dev_info(&adapter->pdev->dev, "rx csum is off, "
+				"cannot toggle lro\n");
+			return -EINVAL;
+		}
 
-	if (data & ETH_FLAG_LRO) {
 		hw_lro = QLCNIC_LRO_ENABLED;
 		netdev->features |= NETIF_F_LRO;
+
 	} else {
+
+		if (!(netdev->features & NETIF_F_LRO))
+			return 0;
+
 		hw_lro = 0;
 		netdev->features &= ~NETIF_F_LRO;
 	}

drivers/net/qlcnic/qlcnic_hw.c

@@ -566,6 +566,9 @@ int qlcnic_config_hw_lro(struct qlcnic_adapter *adapter, int enable)
 	u64 word;
 	int rv;
 
+	if (!test_bit(__QLCNIC_FW_ATTACHED, &adapter->state))
+		return 0;
+
 	memset(&req, 0, sizeof(struct qlcnic_nic_req));
 
 	req.qhdr = cpu_to_le64(QLCNIC_HOST_REQUEST << 23);
@@ -711,6 +714,9 @@ int qlcnic_send_lro_cleanup(struct qlcnic_adapter *adapter)
 	u64 word;
 	int rv;
 
+	if (!test_bit(__QLCNIC_FW_ATTACHED, &adapter->state))
+		return 0;
+
 	memset(&req, 0, sizeof(struct qlcnic_nic_req));
 	req.qhdr = cpu_to_le64(QLCNIC_HOST_REQUEST << 23);
 

drivers/net/qlcnic/qlcnic_main.c

@@ -773,7 +773,8 @@ qlcnic_set_netdev_features(struct qlcnic_adapter *adapter,
 		features |= (NETIF_F_TSO | NETIF_F_TSO6);
 		vlan_features |= (NETIF_F_TSO | NETIF_F_TSO6);
 	}
-	if (adapter->capabilities & QLCNIC_FW_CAPABILITY_HW_LRO)
+
+	if (netdev->features & NETIF_F_LRO)
 		features |= NETIF_F_LRO;
 
 	if (esw_cfg->offload_flags & BIT_0) {