Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
提交 b11b867f 编写于 作者: I Ingo Molnar
浏览文件
操作

x86, summit: consolidate code 

Consolidate all the Summit code into a single file:
arch/x86/kernel/summit_32.c.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
上级 5a44632f
隐藏空白更改
内联 并排
Showing with 416 addition and 435 deletion
arch/x86/include/asm/summit/apic.h 已删除 100644 → 0
浏览文件 @ 5a44632f
#ifndef __ASM_SUMMIT_APIC_H
#define __ASM_SUMMIT_APIC_H
#include <asm/smp.h>
#include <linux/gfp.h>
/* In clustered mode, the high nibble of APIC ID is a cluster number.
* The low nibble is a 4-bit bitmap. */
#define XAPIC_DEST_CPUS_SHIFT 4
#define XAPIC_DEST_CPUS_MASK ((1u << XAPIC_DEST_CPUS_SHIFT) - 1)
#define XAPIC_DEST_CLUSTER_MASK (XAPIC_DEST_CPUS_MASK << XAPIC_DEST_CPUS_SHIFT)
#define APIC_DFR_VALUE (APIC_DFR_CLUSTER)
static inline const cpumask_t *summit_target_cpus(void)
{
/* CPU_MASK_ALL (0xff) has undefined behaviour with
* dest_LowestPrio mode logical clustered apic interrupt routing
* Just start on cpu 0. IRQ balancing will spread load
*/
return &cpumask_of_cpu(0);
}
static inline unsigned long
summit_check_apicid_used(physid_mask_t bitmap, int apicid)
{
return 0;
}
/* we don't use the phys_cpu_present_map to indicate apicid presence */
static inline unsigned long summit_check_apicid_present(int bit)
{
return 1;
}
#define apicid_cluster(apicid) ((apicid) & XAPIC_DEST_CLUSTER_MASK)
extern u8 cpu_2_logical_apicid[];
static inline void summit_init_apic_ldr(void)
{
unsigned long val, id;
int count = 0;
u8 my_id = (u8)hard_smp_processor_id();
u8 my_cluster = (u8)apicid_cluster(my_id);
#ifdef CONFIG_SMP
u8 lid;
int i;
/* Create logical APIC IDs by counting CPUs already in cluster. */
for (count = 0, i = nr_cpu_ids; --i >= 0; ) {
lid = cpu_2_logical_apicid[i];
if (lid != BAD_APICID && apicid_cluster(lid) == my_cluster)
++count;
}
#endif
/* We only have a 4 wide bitmap in cluster mode. If a deranged
* BIOS puts 5 CPUs in one APIC cluster, we're hosed. */
BUG_ON(count >= XAPIC_DEST_CPUS_SHIFT);
id = my_cluster | (1UL << count);
apic_write(APIC_DFR, APIC_DFR_VALUE);
val = apic_read(APIC_LDR) & ~APIC_LDR_MASK;
val |= SET_APIC_LOGICAL_ID(id);
apic_write(APIC_LDR, val);
}
static inline int summit_apic_id_registered(void)
{
return 1;
}
static inline void summit_setup_apic_routing(void)
{
printk("Enabling APIC mode: Summit. Using %d I/O APICs\n",
nr_ioapics);
}
static inline int summit_apicid_to_node(int logical_apicid)
{
#ifdef CONFIG_SMP
return apicid_2_node[hard_smp_processor_id()];
#else
return 0;
#endif
}
/* Mapping from cpu number to logical apicid */
static inline int summit_cpu_to_logical_apicid(int cpu)
{
#ifdef CONFIG_SMP
if (cpu >= nr_cpu_ids)
return BAD_APICID;
return (int)cpu_2_logical_apicid[cpu];
#else
return logical_smp_processor_id();
#endif
}
static inline int summit_cpu_present_to_apicid(int mps_cpu)
{
if (mps_cpu < nr_cpu_ids)
return (int)per_cpu(x86_bios_cpu_apicid, mps_cpu);
else
return BAD_APICID;
}
static inline physid_mask_t
summit_ioapic_phys_id_map(physid_mask_t phys_id_map)
{
/* For clustered we don't have a good way to do this yet - hack */
return physids_promote(0x0F);
}
static inline physid_mask_t summit_apicid_to_cpu_present(int apicid)
{
return physid_mask_of_physid(0);
}
static inline void summit_setup_portio_remap(void)
{
}
static inline int summit_check_phys_apicid_present(int boot_cpu_physical_apicid)
{
return 1;
}
static inline unsigned int summit_cpu_mask_to_apicid(const cpumask_t *cpumask)
{
int cpus_found = 0;
int num_bits_set;
int apicid;
int cpu;
num_bits_set = cpus_weight(*cpumask);
/* Return id to all */
if (num_bits_set >= nr_cpu_ids)
return 0xFF;
/*
* The cpus in the mask must all be on the apic cluster. If are not
* on the same apicid cluster return default value of target_cpus():
*/
cpu = first_cpu(*cpumask);
apicid = summit_cpu_to_logical_apicid(cpu);
while (cpus_found < num_bits_set) {
if (cpu_isset(cpu, *cpumask)) {
int new_apicid = summit_cpu_to_logical_apicid(cpu);
if (apicid_cluster(apicid) !=
apicid_cluster(new_apicid)) {
printk ("%s: Not a valid mask!\n", __func__);
return 0xFF;
}
apicid = apicid | new_apicid;
cpus_found++;
}
cpu++;
}
return apicid;
}
static inline unsigned int
summit_cpu_mask_to_apicid_and(const struct cpumask *inmask,
const struct cpumask *andmask)
{
int apicid = summit_cpu_to_logical_apicid(0);
cpumask_var_t cpumask;
if (!alloc_cpumask_var(&cpumask, GFP_ATOMIC))
return apicid;
cpumask_and(cpumask, inmask, andmask);
cpumask_and(cpumask, cpumask, cpu_online_mask);
apicid = summit_cpu_mask_to_apicid(cpumask);
free_cpumask_var(cpumask);
return apicid;
}
/*
* cpuid returns the value latched in the HW at reset, not the APIC ID
* register's value. For any box whose BIOS changes APIC IDs, like
* clustered APIC systems, we must use hard_smp_processor_id.
*
* See Intel's IA-32 SW Dev's Manual Vol2 under CPUID.
*/
static inline int summit_phys_pkg_id(int cpuid_apic, int index_msb)
{
return hard_smp_processor_id() >> index_msb;
}
#endif /* __ASM_SUMMIT_APIC_H */
arch/x86/include/asm/summit/apicdef.h 已删除 100644 → 0
浏览文件 @ 5a44632f
#ifndef __ASM_SUMMIT_APICDEF_H
#define __ASM_SUMMIT_APICDEF_H
static inline unsigned summit_get_apic_id(unsigned long x)
{
return (x >> 24) & 0xFF;
}
#endif
arch/x86/include/asm/summit/ipi.h 已删除 100644 → 0
浏览文件 @ 5a44632f
#ifndef __ASM_SUMMIT_IPI_H
#define __ASM_SUMMIT_IPI_H
void default_send_IPI_mask_sequence(const cpumask_t *mask, int vector);
void default_send_IPI_mask_allbutself(const cpumask_t *mask, int vector);
static inline void summit_send_IPI_mask(const cpumask_t *mask, int vector)
{
default_send_IPI_mask_sequence(mask, vector);
}
static inline void summit_send_IPI_allbutself(int vector)
{
cpumask_t mask = cpu_online_map;
cpu_clear(smp_processor_id(), mask);
if (!cpus_empty(mask))
summit_send_IPI_mask(&mask, vector);
}
static inline void summit_send_IPI_all(int vector)
{
summit_send_IPI_mask(&cpu_online_map, vector);
}
#endif /* __ASM_SUMMIT_IPI_H */
arch/x86/include/asm/summit/mpparse.h 已删除 100644 → 0
浏览文件 @ 5a44632f
#ifndef __ASM_SUMMIT_MPPARSE_H
#define __ASM_SUMMIT_MPPARSE_H
#include <asm/tsc.h>
extern int use_cyclone;
#ifdef CONFIG_X86_SUMMIT_NUMA
extern void setup_summit(void);
#else
#define setup_summit() {}
#endif
static inline int
summit_mps_oem_check(struct mpc_table *mpc, char *oem, char *productid)
{
if (!strncmp(oem, "IBM ENSW", 8) &&
(!strncmp(productid, "VIGIL SMP", 9)
|| !strncmp(productid, "EXA", 3)
|| !strncmp(productid, "RUTHLESS SMP", 12))){
mark_tsc_unstable("Summit based system");
use_cyclone = 1; /*enable cyclone-timer*/
setup_summit();
return 1;
}
return 0;
}
/* Hook from generic ACPI tables.c */
static inline int summit_acpi_madt_oem_check(char *oem_id, char *oem_table_id)
{
if (!strncmp(oem_id, "IBM", 3) &&
(!strncmp(oem_table_id, "SERVIGIL", 8)
|| !strncmp(oem_table_id, "EXA", 3))){
mark_tsc_unstable("Summit based system");
use_cyclone = 1; /*enable cyclone-timer*/
setup_summit();
return 1;
}
return 0;
}
struct rio_table_hdr {
unsigned char version; /* Version number of this data structure */
/* Version 3 adds chassis_num & WP_index */
unsigned char num_scal_dev; /* # of Scalability devices (Twisters for Vigil) */
unsigned char num_rio_dev; /* # of RIO I/O devices (Cyclones and Winnipegs) */
} __attribute__((packed));
struct scal_detail {
unsigned char node_id; /* Scalability Node ID */
unsigned long CBAR; /* Address of 1MB register space */
unsigned char port0node; /* Node ID port connected to: 0xFF=None */
unsigned char port0port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char port1node; /* Node ID port connected to: 0xFF = None */
unsigned char port1port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char port2node; /* Node ID port connected to: 0xFF = None */
unsigned char port2port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char chassis_num; /* 1 based Chassis number (1 = boot node) */
} __attribute__((packed));
struct rio_detail {
unsigned char node_id; /* RIO Node ID */
unsigned long BBAR; /* Address of 1MB register space */
unsigned char type; /* Type of device */
unsigned char owner_id; /* For WPEG: Node ID of Cyclone that owns this WPEG*/
/* For CYC: Node ID of Twister that owns this CYC */
unsigned char port0node; /* Node ID port connected to: 0xFF=None */
unsigned char port0port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char port1node; /* Node ID port connected to: 0xFF=None */
unsigned char port1port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char first_slot; /* For WPEG: Lowest slot number below this WPEG */
/* For CYC: 0 */
unsigned char status; /* For WPEG: Bit 0 = 1 : the XAPIC is used */
/* = 0 : the XAPIC is not used, ie:*/
/* ints fwded to another XAPIC */
/* Bits1:7 Reserved */
/* For CYC: Bits0:7 Reserved */
unsigned char WP_index; /* For WPEG: WPEG instance index - lower ones have */
/* lower slot numbers/PCI bus numbers */
/* For CYC: No meaning */
unsigned char chassis_num; /* 1 based Chassis number */
/* For LookOut WPEGs this field indicates the */
/* Expansion Chassis #, enumerated from Boot */
/* Node WPEG external port, then Boot Node CYC */
/* external port, then Next Vigil chassis WPEG */
/* external port, etc. */
/* Shared Lookouts have only 1 chassis number (the */
/* first one assigned) */
} __attribute__((packed));
typedef enum {
CompatTwister = 0, /* Compatibility Twister */
AltTwister = 1, /* Alternate Twister of internal 8-way */
CompatCyclone = 2, /* Compatibility Cyclone */
AltCyclone = 3, /* Alternate Cyclone of internal 8-way */
CompatWPEG = 4, /* Compatibility WPEG */
AltWPEG = 5, /* Second Planar WPEG */
LookOutAWPEG = 6, /* LookOut WPEG */
LookOutBWPEG = 7, /* LookOut WPEG */
} node_type;
static inline int is_WPEG(struct rio_detail *rio){
return (rio->type == CompatWPEG || rio->type == AltWPEG ||
rio->type == LookOutAWPEG || rio->type == LookOutBWPEG);
}
#endif /* __ASM_SUMMIT_MPPARSE_H */
arch/x86/kernel/summit_32.c
浏览文件 @ b11b867f
......@@ -30,7 +30,364 @@
#include <linux/init.h>
#include <asm/io.h>
#include <asm/bios_ebda.h>
#include <asm/summit/mpparse.h>
/*
* APIC driver for the IBM "Summit" chipset.
*/
#define APIC_DEFINITION 1
#include <linux/threads.h>
#include <linux/cpumask.h>
#include <asm/mpspec.h>
#include <asm/apic.h>
#include <asm/smp.h>
#include <asm/genapic.h>
#include <asm/fixmap.h>
#include <asm/apicdef.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/init.h>
#include <linux/gfp.h>
#include <linux/smp.h>
static inline unsigned summit_get_apic_id(unsigned long x)
{
return (x >> 24) & 0xFF;
}
void default_send_IPI_mask_sequence(const cpumask_t *mask, int vector);
void default_send_IPI_mask_allbutself(const cpumask_t *mask, int vector);
static inline void summit_send_IPI_mask(const cpumask_t *mask, int vector)
{
default_send_IPI_mask_sequence(mask, vector);
}
static inline void summit_send_IPI_allbutself(int vector)
{
cpumask_t mask = cpu_online_map;
cpu_clear(smp_processor_id(), mask);
if (!cpus_empty(mask))
summit_send_IPI_mask(&mask, vector);
}
static inline void summit_send_IPI_all(int vector)
{
summit_send_IPI_mask(&cpu_online_map, vector);
}
#include <asm/tsc.h>
extern int use_cyclone;
#ifdef CONFIG_X86_SUMMIT_NUMA
extern void setup_summit(void);
#else
#define setup_summit() {}
#endif
static inline int
summit_mps_oem_check(struct mpc_table *mpc, char *oem, char *productid)
{
if (!strncmp(oem, "IBM ENSW", 8) &&
(!strncmp(productid, "VIGIL SMP", 9)
|| !strncmp(productid, "EXA", 3)
|| !strncmp(productid, "RUTHLESS SMP", 12))){
mark_tsc_unstable("Summit based system");
use_cyclone = 1; /*enable cyclone-timer*/
setup_summit();
return 1;
}
return 0;
}
/* Hook from generic ACPI tables.c */
static inline int summit_acpi_madt_oem_check(char *oem_id, char *oem_table_id)
{
if (!strncmp(oem_id, "IBM", 3) &&
(!strncmp(oem_table_id, "SERVIGIL", 8)
|| !strncmp(oem_table_id, "EXA", 3))){
mark_tsc_unstable("Summit based system");
use_cyclone = 1; /*enable cyclone-timer*/
setup_summit();
return 1;
}
return 0;
}
struct rio_table_hdr {
unsigned char version; /* Version number of this data structure */
/* Version 3 adds chassis_num & WP_index */
unsigned char num_scal_dev; /* # of Scalability devices (Twisters for Vigil) */
unsigned char num_rio_dev; /* # of RIO I/O devices (Cyclones and Winnipegs) */
} __attribute__((packed));
struct scal_detail {
unsigned char node_id; /* Scalability Node ID */
unsigned long CBAR; /* Address of 1MB register space */
unsigned char port0node; /* Node ID port connected to: 0xFF=None */
unsigned char port0port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char port1node; /* Node ID port connected to: 0xFF = None */
unsigned char port1port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char port2node; /* Node ID port connected to: 0xFF = None */
unsigned char port2port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char chassis_num; /* 1 based Chassis number (1 = boot node) */
} __attribute__((packed));
struct rio_detail {
unsigned char node_id; /* RIO Node ID */
unsigned long BBAR; /* Address of 1MB register space */
unsigned char type; /* Type of device */
unsigned char owner_id; /* For WPEG: Node ID of Cyclone that owns this WPEG*/
/* For CYC: Node ID of Twister that owns this CYC */
unsigned char port0node; /* Node ID port connected to: 0xFF=None */
unsigned char port0port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char port1node; /* Node ID port connected to: 0xFF=None */
unsigned char port1port; /* Port num port connected to: 0,1,2, or 0xFF=None */
unsigned char first_slot; /* For WPEG: Lowest slot number below this WPEG */
/* For CYC: 0 */
unsigned char status; /* For WPEG: Bit 0 = 1 : the XAPIC is used */
/* = 0 : the XAPIC is not used, ie:*/
/* ints fwded to another XAPIC */
/* Bits1:7 Reserved */
/* For CYC: Bits0:7 Reserved */
unsigned char WP_index; /* For WPEG: WPEG instance index - lower ones have */
/* lower slot numbers/PCI bus numbers */
/* For CYC: No meaning */
unsigned char chassis_num; /* 1 based Chassis number */
/* For LookOut WPEGs this field indicates the */
/* Expansion Chassis #, enumerated from Boot */
/* Node WPEG external port, then Boot Node CYC */
/* external port, then Next Vigil chassis WPEG */
/* external port, etc. */
/* Shared Lookouts have only 1 chassis number (the */
/* first one assigned) */
} __attribute__((packed));
typedef enum {
CompatTwister = 0, /* Compatibility Twister */
AltTwister = 1, /* Alternate Twister of internal 8-way */
CompatCyclone = 2, /* Compatibility Cyclone */
AltCyclone = 3, /* Alternate Cyclone of internal 8-way */
CompatWPEG = 4, /* Compatibility WPEG */
AltWPEG = 5, /* Second Planar WPEG */
LookOutAWPEG = 6, /* LookOut WPEG */
LookOutBWPEG = 7, /* LookOut WPEG */
} node_type;
static inline int is_WPEG(struct rio_detail *rio){
return (rio->type == CompatWPEG || rio->type == AltWPEG ||
rio->type == LookOutAWPEG || rio->type == LookOutBWPEG);
}
/* In clustered mode, the high nibble of APIC ID is a cluster number.
* The low nibble is a 4-bit bitmap. */
#define XAPIC_DEST_CPUS_SHIFT 4
#define XAPIC_DEST_CPUS_MASK ((1u << XAPIC_DEST_CPUS_SHIFT) - 1)
#define XAPIC_DEST_CLUSTER_MASK (XAPIC_DEST_CPUS_MASK << XAPIC_DEST_CPUS_SHIFT)
#define SUMMIT_APIC_DFR_VALUE (APIC_DFR_CLUSTER)
static inline const cpumask_t *summit_target_cpus(void)
{
/* CPU_MASK_ALL (0xff) has undefined behaviour with
* dest_LowestPrio mode logical clustered apic interrupt routing
* Just start on cpu 0. IRQ balancing will spread load
*/
return &cpumask_of_cpu(0);
}
static inline unsigned long
summit_check_apicid_used(physid_mask_t bitmap, int apicid)
{
return 0;
}
/* we don't use the phys_cpu_present_map to indicate apicid presence */
static inline unsigned long summit_check_apicid_present(int bit)
{
return 1;
}
#define apicid_cluster(apicid) ((apicid) & XAPIC_DEST_CLUSTER_MASK)
extern u8 cpu_2_logical_apicid[];
static inline void summit_init_apic_ldr(void)
{
unsigned long val, id;
int count = 0;
u8 my_id = (u8)hard_smp_processor_id();
u8 my_cluster = (u8)apicid_cluster(my_id);
#ifdef CONFIG_SMP
u8 lid;
int i;
/* Create logical APIC IDs by counting CPUs already in cluster. */
for (count = 0, i = nr_cpu_ids; --i >= 0; ) {
lid = cpu_2_logical_apicid[i];
if (lid != BAD_APICID && apicid_cluster(lid) == my_cluster)
++count;
}
#endif
/* We only have a 4 wide bitmap in cluster mode. If a deranged
* BIOS puts 5 CPUs in one APIC cluster, we're hosed. */
BUG_ON(count >= XAPIC_DEST_CPUS_SHIFT);
id = my_cluster | (1UL << count);
apic_write(APIC_DFR, SUMMIT_APIC_DFR_VALUE);
val = apic_read(APIC_LDR) & ~APIC_LDR_MASK;
val |= SET_APIC_LOGICAL_ID(id);
apic_write(APIC_LDR, val);
}
static inline int summit_apic_id_registered(void)
{
return 1;
}
static inline void summit_setup_apic_routing(void)
{
printk("Enabling APIC mode: Summit. Using %d I/O APICs\n",
nr_ioapics);
}
static inline int summit_apicid_to_node(int logical_apicid)
{
#ifdef CONFIG_SMP
return apicid_2_node[hard_smp_processor_id()];
#else
return 0;
#endif
}
/* Mapping from cpu number to logical apicid */
static inline int summit_cpu_to_logical_apicid(int cpu)
{
#ifdef CONFIG_SMP
if (cpu >= nr_cpu_ids)
return BAD_APICID;
return (int)cpu_2_logical_apicid[cpu];
#else
return logical_smp_processor_id();
#endif
}
static inline int summit_cpu_present_to_apicid(int mps_cpu)
{
if (mps_cpu < nr_cpu_ids)
return (int)per_cpu(x86_bios_cpu_apicid, mps_cpu);
else
return BAD_APICID;
}
static inline physid_mask_t
summit_ioapic_phys_id_map(physid_mask_t phys_id_map)
{
/* For clustered we don't have a good way to do this yet - hack */
return physids_promote(0x0F);
}
static inline physid_mask_t summit_apicid_to_cpu_present(int apicid)
{
return physid_mask_of_physid(0);
}
static inline void summit_setup_portio_remap(void)
{
}
static inline int summit_check_phys_apicid_present(int boot_cpu_physical_apicid)
{
return 1;
}
static inline unsigned int summit_cpu_mask_to_apicid(const cpumask_t *cpumask)
{
int cpus_found = 0;
int num_bits_set;
int apicid;
int cpu;
num_bits_set = cpus_weight(*cpumask);
/* Return id to all */
if (num_bits_set >= nr_cpu_ids)
return 0xFF;
/*
* The cpus in the mask must all be on the apic cluster. If are not
* on the same apicid cluster return default value of target_cpus():
*/
cpu = first_cpu(*cpumask);
apicid = summit_cpu_to_logical_apicid(cpu);
while (cpus_found < num_bits_set) {
if (cpu_isset(cpu, *cpumask)) {
int new_apicid = summit_cpu_to_logical_apicid(cpu);
if (apicid_cluster(apicid) !=
apicid_cluster(new_apicid)) {
printk ("%s: Not a valid mask!\n", __func__);
return 0xFF;
}
apicid = apicid | new_apicid;
cpus_found++;
}
cpu++;
}
return apicid;
}
static inline unsigned int
summit_cpu_mask_to_apicid_and(const struct cpumask *inmask,
const struct cpumask *andmask)
{
int apicid = summit_cpu_to_logical_apicid(0);
cpumask_var_t cpumask;
if (!alloc_cpumask_var(&cpumask, GFP_ATOMIC))
return apicid;
cpumask_and(cpumask, inmask, andmask);
cpumask_and(cpumask, cpumask, cpu_online_mask);
apicid = summit_cpu_mask_to_apicid(cpumask);
free_cpumask_var(cpumask);
return apicid;
}
/*
* cpuid returns the value latched in the HW at reset, not the APIC ID
* register's value. For any box whose BIOS changes APIC IDs, like
* clustered APIC systems, we must use hard_smp_processor_id.
*
* See Intel's IA-32 SW Dev's Manual Vol2 under CPUID.
*/
static inline int summit_phys_pkg_id(int cpuid_apic, int index_msb)
{
return hard_smp_processor_id() >> index_msb;
}
static int probe_summit(void)
{
/* probed later in mptable/ACPI hooks */
return 0;
}
static void summit_vector_allocation_domain(int cpu, cpumask_t *retmask)
{
/* Careful. Some cpus do not strictly honor the set of cpus
* specified in the interrupt destination when using lowest
* priority interrupt delivery mode.
*
* In particular there was a hyperthreading cpu observed to
* deliver interrupts to the wrong hyperthread when only one
* hyperthread was specified in the interrupt desitination.
*/
*retmask = (cpumask_t){ { [0] = APIC_ALL_CPUS, } };
}
static struct rio_table_hdr *rio_table_hdr __initdata;
static struct scal_detail *scal_devs[MAX_NUMNODES] __initdata;
......@@ -186,3 +543,61 @@ void __init setup_summit(void)
next_wpeg = 0;
} while (next_wpeg != 0);
}
struct genapic apic_summit = {
.name = "summit",
.probe = probe_summit,
.acpi_madt_oem_check = summit_acpi_madt_oem_check,
.apic_id_registered = summit_apic_id_registered,
.irq_delivery_mode = dest_LowestPrio,
/* logical delivery broadcast to all CPUs: */
.irq_dest_mode = 1,
.target_cpus = summit_target_cpus,
.disable_esr = 1,
.dest_logical = APIC_DEST_LOGICAL,
.check_apicid_used = summit_check_apicid_used,
.check_apicid_present = summit_check_apicid_present,
.vector_allocation_domain = summit_vector_allocation_domain,
.init_apic_ldr = summit_init_apic_ldr,
.ioapic_phys_id_map = summit_ioapic_phys_id_map,
.setup_apic_routing = summit_setup_apic_routing,
.multi_timer_check = NULL,
.apicid_to_node = summit_apicid_to_node,
.cpu_to_logical_apicid = summit_cpu_to_logical_apicid,
.cpu_present_to_apicid = summit_cpu_present_to_apicid,
.apicid_to_cpu_present = summit_apicid_to_cpu_present,
.setup_portio_remap = NULL,
.check_phys_apicid_present = summit_check_phys_apicid_present,
.enable_apic_mode = NULL,
.phys_pkg_id = summit_phys_pkg_id,
.mps_oem_check = summit_mps_oem_check,
.get_apic_id = summit_get_apic_id,
.set_apic_id = NULL,
.apic_id_mask = 0xFF << 24,
.cpu_mask_to_apicid = summit_cpu_mask_to_apicid,
.cpu_mask_to_apicid_and = summit_cpu_mask_to_apicid_and,
.send_IPI_mask = summit_send_IPI_mask,
.send_IPI_mask_allbutself = NULL,
.send_IPI_allbutself = summit_send_IPI_allbutself,
.send_IPI_all = summit_send_IPI_all,
.send_IPI_self = NULL,
.wakeup_cpu = NULL,
.trampoline_phys_low = DEFAULT_TRAMPOLINE_PHYS_LOW,
.trampoline_phys_high = DEFAULT_TRAMPOLINE_PHYS_HIGH,
.wait_for_init_deassert = default_wait_for_init_deassert,
.smp_callin_clear_local_apic = NULL,
.store_NMI_vector = NULL,
.inquire_remote_apic = default_inquire_remote_apic,
};
arch/x86/mach-generic/Makefile
浏览文件 @ b11b867f
......@@ -6,6 +6,5 @@ EXTRA_CFLAGS := -Iarch/x86/kernel
obj-y := probe.o default.o
obj-$(CONFIG_X86_NUMAQ) += numaq.o
obj-$(CONFIG_X86_SUMMIT) += summit.o
obj-$(CONFIG_X86_BIGSMP) += bigsmp.o
obj-$(CONFIG_X86_ES7000) += es7000.o
arch/x86/mach-generic/summit.c 已删除 100644 → 0
浏览文件 @ 5a44632f
/*
* APIC driver for the IBM "Summit" chipset.
*/
#define APIC_DEFINITION 1
#include <linux/threads.h>
#include <linux/cpumask.h>
#include <asm/mpspec.h>
#include <asm/genapic.h>
#include <asm/fixmap.h>
#include <asm/apicdef.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/init.h>
#include <asm/summit/apicdef.h>
#include <linux/smp.h>
#include <asm/summit/apic.h>
#include <asm/summit/ipi.h>
#include <asm/summit/mpparse.h>
static int probe_summit(void)
{
/* probed later in mptable/ACPI hooks */
return 0;
}
static void summit_vector_allocation_domain(int cpu, cpumask_t *retmask)
{
/* Careful. Some cpus do not strictly honor the set of cpus
* specified in the interrupt destination when using lowest
* priority interrupt delivery mode.
*
* In particular there was a hyperthreading cpu observed to
* deliver interrupts to the wrong hyperthread when only one
* hyperthread was specified in the interrupt desitination.
*/
*retmask = (cpumask_t){ { [0] = APIC_ALL_CPUS, } };
}
struct genapic apic_summit = {
.name = "summit",
.probe = probe_summit,
.acpi_madt_oem_check = summit_acpi_madt_oem_check,
.apic_id_registered = summit_apic_id_registered,
.irq_delivery_mode = dest_LowestPrio,
/* logical delivery broadcast to all CPUs: */
.irq_dest_mode = 1,
.target_cpus = summit_target_cpus,
.disable_esr = 1,
.dest_logical = APIC_DEST_LOGICAL,
.check_apicid_used = summit_check_apicid_used,
.check_apicid_present = summit_check_apicid_present,
.vector_allocation_domain = summit_vector_allocation_domain,
.init_apic_ldr = summit_init_apic_ldr,
.ioapic_phys_id_map = summit_ioapic_phys_id_map,
.setup_apic_routing = summit_setup_apic_routing,
.multi_timer_check = NULL,
.apicid_to_node = summit_apicid_to_node,
.cpu_to_logical_apicid = summit_cpu_to_logical_apicid,
.cpu_present_to_apicid = summit_cpu_present_to_apicid,
.apicid_to_cpu_present = summit_apicid_to_cpu_present,
.setup_portio_remap = NULL,
.check_phys_apicid_present = summit_check_phys_apicid_present,
.enable_apic_mode = NULL,
.phys_pkg_id = summit_phys_pkg_id,
.mps_oem_check = summit_mps_oem_check,
.get_apic_id = summit_get_apic_id,
.set_apic_id = NULL,
.apic_id_mask = 0xFF << 24,
.cpu_mask_to_apicid = summit_cpu_mask_to_apicid,
.cpu_mask_to_apicid_and = summit_cpu_mask_to_apicid_and,
.send_IPI_mask = summit_send_IPI_mask,
.send_IPI_mask_allbutself = NULL,
.send_IPI_allbutself = summit_send_IPI_allbutself,
.send_IPI_all = summit_send_IPI_all,
.send_IPI_self = NULL,
.wakeup_cpu = NULL,
.trampoline_phys_low = DEFAULT_TRAMPOLINE_PHYS_LOW,
.trampoline_phys_high = DEFAULT_TRAMPOLINE_PHYS_HIGH,
.wait_for_init_deassert = default_wait_for_init_deassert,
.smp_callin_clear_local_apic = NULL,
.store_NMI_vector = NULL,
.inquire_remote_apic = default_inquire_remote_apic,
};
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或