usb: dwc2: add external_id_pin_ctl core parameter

This is required due to an Intel specific hardware issue. Where id-
pin setup causes glitches on the interrupt line when CONIDSTSCHG
interrupt is enabled.

Specify external_id_pin_ctl when an external driver (for example phy)
can handle id change, so that CONIDSTSCHG interrupt can be disabled
from the controller.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

drivers/usb/dwc2/core.c

@@ -454,8 +454,10 @@ static void dwc2_enable_common_interrupts(struct dwc2_hsotg *hsotg)
 
 	if (hsotg->core_params->dma_enable <= 0)
 		intmsk |= GINTSTS_RXFLVL;
+	if (hsotg->core_params->external_id_pin_ctl <= 0)
+		intmsk |= GINTSTS_CONIDSTSCHNG;
 
-	intmsk |= GINTSTS_CONIDSTSCHNG | GINTSTS_WKUPINT | GINTSTS_USBSUSP |
+	intmsk |= GINTSTS_WKUPINT | GINTSTS_USBSUSP |
 		  GINTSTS_SESSREQINT;
 
 	writel(intmsk, hsotg->regs + GINTMSK);
@@ -2979,6 +2981,23 @@ static void dwc2_set_param_uframe_sched(struct dwc2_hsotg *hsotg, int val)
 	hsotg->core_params->uframe_sched = val;
 }
 
+static void dwc2_set_param_external_id_pin_ctl(struct dwc2_hsotg *hsotg,
+		int val)
+{
+	if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) {
+		if (val >= 0) {
+			dev_err(hsotg->dev,
+				"'%d' invalid for parameter external_id_pin_ctl\n",
+				val);
+			dev_err(hsotg->dev, "external_id_pin_ctl must be 0 or 1\n");
+		}
+		val = 0;
+		dev_dbg(hsotg->dev, "Setting external_id_pin_ctl to %d\n", val);
+	}
+
+	hsotg->core_params->external_id_pin_ctl = val;
+}
+
 /*
  * This function is called during module intialization to pass module parameters
  * for the DWC_otg core.
@@ -3023,6 +3042,7 @@ void dwc2_set_parameters(struct dwc2_hsotg *hsotg,
 	dwc2_set_param_ahbcfg(hsotg, params->ahbcfg);
 	dwc2_set_param_otg_ver(hsotg, params->otg_ver);
 	dwc2_set_param_uframe_sched(hsotg, params->uframe_sched);
+	dwc2_set_param_external_id_pin_ctl(hsotg, params->external_id_pin_ctl);
 }
 
 /**

drivers/usb/dwc2/core.h

@@ -331,6 +331,11 @@ enum dwc2_ep0_state {
  *                      by the driver and are ignored in this
  *                      configuration value.
  * @uframe_sched:       True to enable the microframe scheduler
+ * @external_id_pin_ctl: Specifies whether ID pin is handled externally.
+ *                      Disable CONIDSTSCHNG controller interrupt in such
+ *                      case.
+ *                      0 - No (default)
+ *                      1 - Yes
  *
  * The following parameters may be specified when starting the module. These
  * parameters define how the DWC_otg controller should be configured. A
@@ -368,6 +373,7 @@ struct dwc2_core_params {
 	int reload_ctl;
 	int ahbcfg;
 	int uframe_sched;
+	int external_id_pin_ctl;
 };
 
 /**

drivers/usb/dwc2/platform.c

@@ -77,6 +77,7 @@ static const struct dwc2_core_params params_bcm2835 = {
 	.reload_ctl			= 0,
 	.ahbcfg				= 0x10,
 	.uframe_sched			= 0,
+	.external_id_pin_ctl		= -1,
 };
 
 static const struct dwc2_core_params params_rk3066 = {
@@ -105,6 +106,7 @@ static const struct dwc2_core_params params_rk3066 = {
 	.reload_ctl			= -1,
 	.ahbcfg				= 0x7, /* INCR16 */
 	.uframe_sched			= -1,
+	.external_id_pin_ctl		= -1,
 };
 
 /**