Merge tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd

Pull MTD update from David Woodhouse:

 - Lots of cleanups from Artem, including deletion of some obsolete
   drivers

 - Support partitions larger than 4GiB in device tree

 - Support for new SPI chips

* tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits)
  mtd: omap2: Use module_platform_driver()
  mtd: bf5xx_nand: Use module_platform_driver()
  mtd: denali_dt: Remove redundant use of of_match_ptr
  mtd: denali_dt: Change return value to fix smatch warning
  mtd: denali_dt: Use module_platform_driver()
  mtd: denali_dt: Fix incorrect error check
  mtd: nand: subpage write support for hardware based ECC schemes
  mtd: omap2: use msecs_to_jiffies()
  mtd: nand_ids: use size macros
  mtd: nand_ids: improve LEGACY_ID_NAND macro a bit
  mtd: add 4 Toshiba nand chips for the full-id case
  mtd: add the support to parse out the full-id nand type
  mtd: add new fields to nand_flash_dev{}
  mtd: sh_flctl: Use of_match_ptr() macro
  mtd: gpio: Use of_match_ptr() macro
  mtd: gpio: Use devm_kzalloc()
  mtd: davinci_nand: Use of_match_ptr()
  mtd: dataflash: Use of_match_ptr() macro
  mtd: remove h720x flash support
  mtd: onenand: remove OneNAND simulator
  ...

Documentation/ABI/testing/sysfs-class-mtd

@@ -14,8 +14,7 @@ Description:
 		The /sys/class/mtd/mtd{0,1,2,3,...} directories correspond
 		to each /dev/mtdX character device.  These may represent
 		physical/simulated flash devices, partitions on a flash
-		device, or concatenated flash devices.  They exist regardless
-		of whether CONFIG_MTD_CHAR is actually enabled.
+		device, or concatenated flash devices.
 
 What:		/sys/class/mtd/mtdXro/
 Date:		April 2009
@@ -23,8 +22,7 @@ KernelVersion:	2.6.29
 Contact:	linux-mtd@lists.infradead.org
 Description:
 		These directories provide the corresponding read-only device
-		nodes for /sys/class/mtd/mtdX/ .  They are only created
-		(for the benefit of udev) if CONFIG_MTD_CHAR is enabled.
+		nodes for /sys/class/mtd/mtdX/ .
 
 What:		/sys/class/mtd/mtdX/dev
 Date:		April 2009

Documentation/devicetree/bindings/mtd/partition.txt

@@ -5,8 +5,12 @@ on platforms which have strong conventions about which portions of a flash are
 used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
 
-#address-cells & #size-cells must both be present in the mtd device and be
-equal to 1.
+#address-cells & #size-cells must both be present in the mtd device. There are
+two valid values for both:
+<1>: for partitions that require a single 32-bit cell to represent their
+     size/address (aka the value is below 4 GiB)
+<2>: for partitions that require two 32-bit cells to represent their
+     size/address (aka the value is 4 GiB or greater).
 
 Required properties:
 - reg : The partition's offset and size within the mtd bank.
@@ -36,3 +40,31 @@ flash@0 {
 		reg = <0x0100000 0x200000>;
 	};
 };
+
+flash@1 {
+	#address-cells = <1>;
+	#size-cells = <2>;
+
+	/* a 4 GiB partition */
+	partition@0 {
+		label = "filesystem";
+		reg = <0x00000000 0x1 0x00000000>;
+	};
+};
+
+flash@2 {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	/* an 8 GiB partition */
+	partition@0 {
+		label = "filesystem #1";
+		reg = <0x0 0x00000000 0x2 0x00000000>;
+	};
+
+	/* a 4 GiB partition */
+	partition@200000000 {
+		label = "filesystem #2";
+		reg = <0x2 0x00000000 0x1 0x00000000>;
+	};
+};

arch/arm/mach-pxa/Kconfig

@@ -162,7 +162,6 @@ config MACH_XCEP
 	select MTD
 	select MTD_CFI
 	select MTD_CFI_INTELEXT
-	select MTD_CHAR
 	select MTD_PHYSMAP
 	select PXA25x
 	select SMC91X

arch/cris/Kconfig

@@ -264,7 +264,6 @@ config ETRAX_AXISFLASHMAP
 	select MTD_CFI
 	select MTD_CFI_AMDSTD
 	select MTD_JEDECPROBE if ETRAX_ARCH_V32
-	select MTD_CHAR
 	select MTD_BLOCK
 	select MTD_COMPLEX_MAPPINGS
 	help

arch/cris/arch-v32/drivers/Kconfig

@@ -404,7 +404,6 @@ config ETRAX_AXISFLASHMAP
 	select MTD_CFI
 	select MTD_CFI_AMDSTD
 	select MTD_JEDECPROBE
-	select MTD_CHAR
 	select MTD_BLOCK
 	select MTD_COMPLEX_MAPPINGS
 	help

drivers/bcma/driver_mips.c

@@ -21,7 +21,7 @@
 #include <linux/serial_reg.h>
 #include <linux/time.h>
 
-static const char *part_probes[] = { "bcm47xxpart", NULL };
+static const char * const part_probes[] = { "bcm47xxpart", NULL };
 
 static struct physmap_flash_data bcma_pflash_data = {
 	.part_probe_types	= part_probes,

drivers/mtd/Kconfig

@@ -157,19 +157,6 @@ config MTD_BCM47XX_PARTS
 
 comment "User Modules And Translation Layers"
 
-config MTD_CHAR
-	tristate "Direct char device access to MTD devices"
-	help
-	  This provides a character device for each MTD device present in
-	  the system, allowing the user to read and write directly to the
-	  memory chips, and also use ioctl() to obtain information about
-	  the device, or to erase parts of it.
-
-config HAVE_MTD_OTP
-	bool
-	help
-	  Enable access to OTP regions using MTD_CHAR.
-
 config MTD_BLKDEVS
 	tristate "Common interface to block layer for MTD 'translation layers'"
 	depends on BLOCK

drivers/mtd/Makefile

@@ -4,7 +4,7 @@
 
 # Core functionality.
 obj-$(CONFIG_MTD)		+= mtd.o
-mtd-y				:= mtdcore.o mtdsuper.o mtdconcat.o mtdpart.o
+mtd-y				:= mtdcore.o mtdsuper.o mtdconcat.o mtdpart.o mtdchar.o
 
 obj-$(CONFIG_MTD_OF_PARTS)	+= ofpart.o
 obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
@@ -15,7 +15,6 @@ obj-$(CONFIG_MTD_BCM63XX_PARTS)	+= bcm63xxpart.o
 obj-$(CONFIG_MTD_BCM47XX_PARTS)	+= bcm47xxpart.o
 
 # 'Users' - code which presents functionality to userspace.
-obj-$(CONFIG_MTD_CHAR)		+= mtdchar.o
 obj-$(CONFIG_MTD_BLKDEVS)	+= mtd_blkdevs.o
 obj-$(CONFIG_MTD_BLOCK)		+= mtdblock.o
 obj-$(CONFIG_MTD_BLOCK_RO)	+= mtdblock_ro.o

drivers/mtd/chips/Kconfig

@@ -146,7 +146,6 @@ config MTD_CFI_I8
 config MTD_OTP
 	bool "Protection Registers aka one-time programmable (OTP) bits"
 	depends on MTD_CFI_ADV_OPTIONS
-	select HAVE_MTD_OTP
 	default n
 	help
 	  This enables support for reading, writing and locking so called

drivers/mtd/devices/Kconfig

@@ -71,7 +71,6 @@ config MTD_DATAFLASH_WRITE_VERIFY
 config MTD_DATAFLASH_OTP
 	bool "DataFlash OTP support (Security Register)"
 	depends on MTD_DATAFLASH
-	select HAVE_MTD_OTP
 	help
 	  Newer DataFlash chips (revisions C and D) support 128 bytes of
 	  one-time-programmable (OTP) data.  The first half may be written
@@ -205,69 +204,6 @@ config MTD_BLOCK2MTD
 
 comment "Disk-On-Chip Device Drivers"
 
-config MTD_DOC2000
-	tristate "M-Systems Disk-On-Chip 2000 and Millennium (DEPRECATED)"
-	depends on MTD_NAND
-	select MTD_DOCPROBE
-	select MTD_NAND_IDS
-	---help---
-	  This provides an MTD device driver for the M-Systems DiskOnChip
-	  2000 and Millennium devices.  Originally designed for the DiskOnChip
-	  2000, it also now includes support for the DiskOnChip Millennium.
-	  If you have problems with this driver and the DiskOnChip Millennium,
-	  you may wish to try the alternative Millennium driver below. To use
-	  the alternative driver, you will need to undefine DOC_SINGLE_DRIVER
-	  in the <file:drivers/mtd/devices/docprobe.c> source code.
-
-	  If you use this device, you probably also want to enable the NFTL
-	  'NAND Flash Translation Layer' option below, which is used to
-	  emulate a block device by using a kind of file system on the flash
-	  chips.
-
-	  NOTE: This driver is deprecated and will probably be removed soon.
-	  Please try the new DiskOnChip driver under "NAND Flash Device
-	  Drivers".
-
-config MTD_DOC2001
-	tristate "M-Systems Disk-On-Chip Millennium-only alternative driver (DEPRECATED)"
-	depends on MTD_NAND
-	select MTD_DOCPROBE
-	select MTD_NAND_IDS
-	---help---
-	  This provides an alternative MTD device driver for the M-Systems
-	  DiskOnChip Millennium devices.  Use this if you have problems with
-	  the combined DiskOnChip 2000 and Millennium driver above.  To get
-	  the DiskOnChip probe code to load and use this driver instead of
-	  the other one, you will need to undefine DOC_SINGLE_DRIVER near
-	  the beginning of <file:drivers/mtd/devices/docprobe.c>.
-
-	  If you use this device, you probably also want to enable the NFTL
-	  'NAND Flash Translation Layer' option below, which is used to
-	  emulate a block device by using a kind of file system on the flash
-	  chips.
-
-	  NOTE: This driver is deprecated and will probably be removed soon.
-	  Please try the new DiskOnChip driver under "NAND Flash Device
-	  Drivers".
-
-config MTD_DOC2001PLUS
-	tristate "M-Systems Disk-On-Chip Millennium Plus"
-	depends on MTD_NAND
-	select MTD_DOCPROBE
-	select MTD_NAND_IDS
-	---help---
-	  This provides an MTD device driver for the M-Systems DiskOnChip
-	  Millennium Plus devices.
-
-	  If you use this device, you probably also want to enable the INFTL
-	  'Inverse NAND Flash Translation Layer' option below, which is used
-	  to emulate a block device by using a kind of file system on the
-	  flash chips.
-
-	  NOTE: This driver will soon be replaced by the new DiskOnChip driver
-	  under "NAND Flash Device Drivers" (currently that driver does not
-	  support all Millennium Plus devices).
-
 config MTD_DOCG3
 	tristate "M-Systems Disk-On-Chip G3"
 	select BCH

drivers/mtd/devices/Makefile

@@ -2,12 +2,7 @@
 # linux/drivers/mtd/devices/Makefile
 #
 
-obj-$(CONFIG_MTD_DOC2000)	+= doc2000.o
-obj-$(CONFIG_MTD_DOC2001)	+= doc2001.o
-obj-$(CONFIG_MTD_DOC2001PLUS)	+= doc2001plus.o
 obj-$(CONFIG_MTD_DOCG3)		+= docg3.o
-obj-$(CONFIG_MTD_DOCPROBE)	+= docprobe.o
-obj-$(CONFIG_MTD_DOCECC)	+= docecc.o
 obj-$(CONFIG_MTD_SLRAM)		+= slram.o
 obj-$(CONFIG_MTD_PHRAM)		+= phram.o
 obj-$(CONFIG_MTD_PMC551)	+= pmc551.o

drivers/mtd/devices/bcm47xxsflash.c

@@ -10,7 +10,7 @@
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("Serial flash driver for BCMA bus");
 
-static const char *probes[] = { "bcm47xxpart", NULL };
+static const char * const probes[] = { "bcm47xxpart", NULL };
 
 static int bcm47xxsflash_read(struct mtd_info *mtd, loff_t from, size_t len,
 			      size_t *retlen, u_char *buf)
@@ -61,6 +61,17 @@ static int bcm47xxsflash_bcma_probe(struct platform_device *pdev)
 	}
 	sflash->priv = b47s;
 
+	b47s->bcma_cc = container_of(sflash, struct bcma_drv_cc, sflash);
+
+	switch (b47s->bcma_cc->capabilities & BCMA_CC_CAP_FLASHT) {
+	case BCMA_CC_FLASHT_STSER:
+		b47s->type = BCM47XXSFLASH_TYPE_ST;
+		break;
+	case BCMA_CC_FLASHT_ATSER:
+		b47s->type = BCM47XXSFLASH_TYPE_ATMEL;
+		break;
+	}
+
 	b47s->window = sflash->window;
 	b47s->blocksize = sflash->blocksize;
 	b47s->numblocks = sflash->numblocks;

drivers/mtd/devices/bcm47xxsflash.h

@@ -3,7 +3,66 @@
 
 #include <linux/mtd/mtd.h>
 
+/* Used for ST flashes only. */
+#define OPCODE_ST_WREN		0x0006		/* Write Enable */
+#define OPCODE_ST_WRDIS		0x0004		/* Write Disable */
+#define OPCODE_ST_RDSR		0x0105		/* Read Status Register */
+#define OPCODE_ST_WRSR		0x0101		/* Write Status Register */
+#define OPCODE_ST_READ		0x0303		/* Read Data Bytes */
+#define OPCODE_ST_PP		0x0302		/* Page Program */
+#define OPCODE_ST_SE		0x02d8		/* Sector Erase */
+#define OPCODE_ST_BE		0x00c7		/* Bulk Erase */
+#define OPCODE_ST_DP		0x00b9		/* Deep Power-down */
+#define OPCODE_ST_RES		0x03ab		/* Read Electronic Signature */
+#define OPCODE_ST_CSA		0x1000		/* Keep chip select asserted */
+#define OPCODE_ST_SSE		0x0220		/* Sub-sector Erase */
+
+/* Used for Atmel flashes only. */
+#define OPCODE_AT_READ				0x07e8
+#define OPCODE_AT_PAGE_READ			0x07d2
+#define OPCODE_AT_STATUS			0x01d7
+#define OPCODE_AT_BUF1_WRITE			0x0384
+#define OPCODE_AT_BUF2_WRITE			0x0387
+#define OPCODE_AT_BUF1_ERASE_PROGRAM		0x0283
+#define OPCODE_AT_BUF2_ERASE_PROGRAM		0x0286
+#define OPCODE_AT_BUF1_PROGRAM			0x0288
+#define OPCODE_AT_BUF2_PROGRAM			0x0289
+#define OPCODE_AT_PAGE_ERASE			0x0281
+#define OPCODE_AT_BLOCK_ERASE			0x0250
+#define OPCODE_AT_BUF1_WRITE_ERASE_PROGRAM	0x0382
+#define OPCODE_AT_BUF2_WRITE_ERASE_PROGRAM	0x0385
+#define OPCODE_AT_BUF1_LOAD			0x0253
+#define OPCODE_AT_BUF2_LOAD			0x0255
+#define OPCODE_AT_BUF1_COMPARE			0x0260
+#define OPCODE_AT_BUF2_COMPARE			0x0261
+#define OPCODE_AT_BUF1_REPROGRAM		0x0258
+#define OPCODE_AT_BUF2_REPROGRAM		0x0259
+
+/* Status register bits for ST flashes */
+#define SR_ST_WIP		0x01		/* Write In Progress */
+#define SR_ST_WEL		0x02		/* Write Enable Latch */
+#define SR_ST_BP_MASK		0x1c		/* Block Protect */
+#define SR_ST_BP_SHIFT		2
+#define SR_ST_SRWD		0x80		/* Status Register Write Disable */
+
+/* Status register bits for Atmel flashes */
+#define SR_AT_READY		0x80
+#define SR_AT_MISMATCH		0x40
+#define SR_AT_ID_MASK		0x38
+#define SR_AT_ID_SHIFT		3
+
+struct bcma_drv_cc;
+
+enum bcm47xxsflash_type {
+	BCM47XXSFLASH_TYPE_ATMEL,
+	BCM47XXSFLASH_TYPE_ST,
+};
+
 struct bcm47xxsflash {
+	struct bcma_drv_cc *bcma_cc;
+
+	enum bcm47xxsflash_type type;
+
 	u32 window;
 	u32 blocksize;
 	u16 numblocks;

drivers/mtd/devices/docecc.c

-/*
- * ECC algorithm for M-systems disk on chip. We use the excellent Reed
- * Solmon code of Phil Karn (karn@ka9q.ampr.org) available under the
- * GNU GPL License. The rest is simply to convert the disk on chip
- * syndrome into a standard syndome.
- *
- * Author: Fabrice Bellard (fabrice.bellard@netgem.com)
- * Copyright (C) 2000 Netgem S.A.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/types.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/doc2000.h>
-
-#define DEBUG_ECC 0
-/* need to undef it (from asm/termbits.h) */
-#undef B0
-
-#define MM 10 /* Symbol size in bits */
-#define KK (1023-4) /* Number of data symbols per block */
-#define B0 510 /* First root of generator polynomial, alpha form */
-#define PRIM 1 /* power of alpha used to generate roots of generator poly */
-#define	NN ((1 << MM) - 1)
-
-typedef unsigned short dtype;
-
-/* 1+x^3+x^10 */
-static const int Pp[MM+1] = { 1, 0, 0, 1, 0, 0, 0, 0, 0, 0, 1 };
-
-/* This defines the type used to store an element of the Galois Field
- * used by the code. Make sure this is something larger than a char if
- * if anything larger than GF(256) is used.
- *
- * Note: unsigned char will work up to GF(256) but int seems to run
- * faster on the Pentium.
- */
-typedef int gf;
-
-/* No legal value in index form represents zero, so
- * we need a special value for this purpose
- */
-#define A0	(NN)
-
-/* Compute x % NN, where NN is 2**MM - 1,
- * without a slow divide
- */
-static inline gf
-modnn(int x)
-{
-  while (x >= NN) {
-    x -= NN;
-    x = (x >> MM) + (x & NN);
-  }
-  return x;
-}
-
-#define	CLEAR(a,n) {\
-int ci;\
-for(ci=(n)-1;ci >=0;ci--)\
-(a)[ci] = 0;\
-}
-
-#define	COPY(a,b,n) {\
-int ci;\
-for(ci=(n)-1;ci >=0;ci--)\
-(a)[ci] = (b)[ci];\
-}
-
-#define	COPYDOWN(a,b,n) {\
-int ci;\
-for(ci=(n)-1;ci >=0;ci--)\
-(a)[ci] = (b)[ci];\
-}
-
-#define Ldec 1
-
-/* generate GF(2**m) from the irreducible polynomial p(X) in Pp[0]..Pp[m]
-   lookup tables:  index->polynomial form   alpha_to[] contains j=alpha**i;
-                   polynomial form -> index form  index_of[j=alpha**i] = i
-   alpha=2 is the primitive element of GF(2**m)
-   HARI's COMMENT: (4/13/94) alpha_to[] can be used as follows:
-        Let @ represent the primitive element commonly called "alpha" that
-   is the root of the primitive polynomial p(x). Then in GF(2^m), for any
-   0 <= i <= 2^m-2,
-        @^i = a(0) + a(1) @ + a(2) @^2 + ... + a(m-1) @^(m-1)
-   where the binary vector (a(0),a(1),a(2),...,a(m-1)) is the representation
-   of the integer "alpha_to[i]" with a(0) being the LSB and a(m-1) the MSB. Thus for
-   example the polynomial representation of @^5 would be given by the binary
-   representation of the integer "alpha_to[5]".
-                   Similarly, index_of[] can be used as follows:
-        As above, let @ represent the primitive element of GF(2^m) that is
-   the root of the primitive polynomial p(x). In order to find the power
-   of @ (alpha) that has the polynomial representation
-        a(0) + a(1) @ + a(2) @^2 + ... + a(m-1) @^(m-1)
-   we consider the integer "i" whose binary representation with a(0) being LSB
-   and a(m-1) MSB is (a(0),a(1),...,a(m-1)) and locate the entry
-   "index_of[i]". Now, @^index_of[i] is that element whose polynomial
-    representation is (a(0),a(1),a(2),...,a(m-1)).
-   NOTE:
-        The element alpha_to[2^m-1] = 0 always signifying that the
-   representation of "@^infinity" = 0 is (0,0,0,...,0).
-        Similarly, the element index_of[0] = A0 always signifying
-   that the power of alpha which has the polynomial representation
-   (0,0,...,0) is "infinity".
-
-*/
-
-static void
-generate_gf(dtype Alpha_to[NN + 1], dtype Index_of[NN + 1])
-{
-  register int i, mask;
-
-  mask = 1;
-  Alpha_to[MM] = 0;
-  for (i = 0; i < MM; i++) {
-    Alpha_to[i] = mask;
-    Index_of[Alpha_to[i]] = i;
-    /* If Pp[i] == 1 then, term @^i occurs in poly-repr of @^MM */
-    if (Pp[i] != 0)
-      Alpha_to[MM] ^= mask;	/* Bit-wise EXOR operation */
-    mask <<= 1;	/* single left-shift */
-  }
-  Index_of[Alpha_to[MM]] = MM;
-  /*
-   * Have obtained poly-repr of @^MM. Poly-repr of @^(i+1) is given by
-   * poly-repr of @^i shifted left one-bit and accounting for any @^MM
-   * term that may occur when poly-repr of @^i is shifted.
-   */
-  mask >>= 1;
-  for (i = MM + 1; i < NN; i++) {
-    if (Alpha_to[i - 1] >= mask)
-      Alpha_to[i] = Alpha_to[MM] ^ ((Alpha_to[i - 1] ^ mask) << 1);
-    else
-      Alpha_to[i] = Alpha_to[i - 1] << 1;
-    Index_of[Alpha_to[i]] = i;
-  }
-  Index_of[0] = A0;
-  Alpha_to[NN] = 0;
-}
-
-/*
- * Performs ERRORS+ERASURES decoding of RS codes. bb[] is the content
- * of the feedback shift register after having processed the data and
- * the ECC.
- *
- * Return number of symbols corrected, or -1 if codeword is illegal
- * or uncorrectable. If eras_pos is non-null, the detected error locations
- * are written back. NOTE! This array must be at least NN-KK elements long.
- * The corrected data are written in eras_val[]. They must be xor with the data
- * to retrieve the correct data : data[erase_pos[i]] ^= erase_val[i] .
- *
- * First "no_eras" erasures are declared by the calling program. Then, the
- * maximum # of errors correctable is t_after_eras = floor((NN-KK-no_eras)/2).
- * If the number of channel errors is not greater than "t_after_eras" the
- * transmitted codeword will be recovered. Details of algorithm can be found
- * in R. Blahut's "Theory ... of Error-Correcting Codes".
-
- * Warning: the eras_pos[] array must not contain duplicate entries; decoder failure
- * will result. The decoder *could* check for this condition, but it would involve
- * extra time on every decoding operation.
- * */
-static int
-eras_dec_rs(dtype Alpha_to[NN + 1], dtype Index_of[NN + 1],
-            gf bb[NN - KK + 1], gf eras_val[NN-KK], int eras_pos[NN-KK],
-            int no_eras)
-{
-  int deg_lambda, el, deg_omega;
-  int i, j, r,k;
-  gf u,q,tmp,num1,num2,den,discr_r;
-  gf lambda[NN-KK + 1], s[NN-KK + 1];	/* Err+Eras Locator poly
-					 * and syndrome poly */
-  gf b[NN-KK + 1], t[NN-KK + 1], omega[NN-KK + 1];
-  gf root[NN-KK], reg[NN-KK + 1], loc[NN-KK];
-  int syn_error, count;
-
-  syn_error = 0;
-  for(i=0;i<NN-KK;i++)
-      syn_error |= bb[i];
-
-  if (!syn_error) {
-    /* if remainder is zero, data[] is a codeword and there are no
-     * errors to correct. So return data[] unmodified
-     */
-    count = 0;
-    goto finish;
-  }
-
-  for(i=1;i<=NN-KK;i++){
-    s[i] = bb[0];
-  }
-  for(j=1;j<NN-KK;j++){
-    if(bb[j] == 0)
-      continue;
-    tmp = Index_of[bb[j]];
-
-    for(i=1;i<=NN-KK;i++)
-      s[i] ^= Alpha_to[modnn(tmp + (B0+i-1)*PRIM*j)];
-  }
-
-  /* undo the feedback register implicit multiplication and convert
-     syndromes to index form */
-
-  for(i=1;i<=NN-KK;i++) {
-      tmp = Index_of[s[i]];
-      if (tmp != A0)
-          tmp = modnn(tmp + 2 * KK * (B0+i-1)*PRIM);
-      s[i] = tmp;
-  }
-
-  CLEAR(&lambda[1],NN-KK);
-  lambda[0] = 1;
-
-  if (no_eras > 0) {
-    /* Init lambda to be the erasure locator polynomial */
-    lambda[1] = Alpha_to[modnn(PRIM * eras_pos[0])];
-    for (i = 1; i < no_eras; i++) {
-      u = modnn(PRIM*eras_pos[i]);
-      for (j = i+1; j > 0; j--) {
-	tmp = Index_of[lambda[j - 1]];
-	if(tmp != A0)
-	  lambda[j] ^= Alpha_to[modnn(u + tmp)];
-      }
-    }
-#if DEBUG_ECC >= 1
-    /* Test code that verifies the erasure locator polynomial just constructed
-       Needed only for decoder debugging. */
-
-    /* find roots of the erasure location polynomial */
-    for(i=1;i<=no_eras;i++)
-      reg[i] = Index_of[lambda[i]];
-    count = 0;
-    for (i = 1,k=NN-Ldec; i <= NN; i++,k = modnn(NN+k-Ldec)) {
-      q = 1;
-      for (j = 1; j <= no_eras; j++)
-	if (reg[j] != A0) {
-	  reg[j] = modnn(reg[j] + j);
-	  q ^= Alpha_to[reg[j]];
-	}
-      if (q != 0)
-	continue;
-      /* store root and error location number indices */
-      root[count] = i;
-      loc[count] = k;
-      count++;
-    }
-    if (count != no_eras) {
-      printf("\n lambda(x) is WRONG\n");
-      count = -1;
-      goto finish;
-    }
-#if DEBUG_ECC >= 2
-    printf("\n Erasure positions as determined by roots of Eras Loc Poly:\n");
-    for (i = 0; i < count; i++)
-      printf("%d ", loc[i]);
-    printf("\n");
-#endif
-#endif
-  }
-  for(i=0;i<NN-KK+1;i++)
-    b[i] = Index_of[lambda[i]];
-
-  /*
-   * Begin Berlekamp-Massey algorithm to determine error+erasure
-   * locator polynomial
-   */
-  r = no_eras;
-  el = no_eras;
-  while (++r <= NN-KK) {	/* r is the step number */
-    /* Compute discrepancy at the r-th step in poly-form */
-    discr_r = 0;
-    for (i = 0; i < r; i++){
-      if ((lambda[i] != 0) && (s[r - i] != A0)) {
-	discr_r ^= Alpha_to[modnn(Index_of[lambda[i]] + s[r - i])];
-      }
-    }
-    discr_r = Index_of[discr_r];	/* Index form */
-    if (discr_r == A0) {
-      /* 2 lines below: B(x) <-- x*B(x) */
-      COPYDOWN(&b[1],b,NN-KK);
-      b[0] = A0;
-    } else {
-      /* 7 lines below: T(x) <-- lambda(x) - discr_r*x*b(x) */
-      t[0] = lambda[0];
-      for (i = 0 ; i < NN-KK; i++) {
-	if(b[i] != A0)
-	  t[i+1] = lambda[i+1] ^ Alpha_to[modnn(discr_r + b[i])];
-	else
-	  t[i+1] = lambda[i+1];
-      }
-      if (2 * el <= r + no_eras - 1) {
-	el = r + no_eras - el;
-	/*
-	 * 2 lines below: B(x) <-- inv(discr_r) *
-	 * lambda(x)
-	 */
-	for (i = 0; i <= NN-KK; i++)
-	  b[i] = (lambda[i] == 0) ? A0 : modnn(Index_of[lambda[i]] - discr_r + NN);
-      } else {
-	/* 2 lines below: B(x) <-- x*B(x) */
-	COPYDOWN(&b[1],b,NN-KK);
-	b[0] = A0;
-      }
-      COPY(lambda,t,NN-KK+1);
-    }
-  }
-
-  /* Convert lambda to index form and compute deg(lambda(x)) */
-  deg_lambda = 0;
-  for(i=0;i<NN-KK+1;i++){
-    lambda[i] = Index_of[lambda[i]];
-    if(lambda[i] != A0)
-      deg_lambda = i;
-  }
-  /*
-   * Find roots of the error+erasure locator polynomial by Chien
-   * Search
-   */
-  COPY(&reg[1],&lambda[1],NN-KK);
-  count = 0;		/* Number of roots of lambda(x) */
-  for (i = 1,k=NN-Ldec; i <= NN; i++,k = modnn(NN+k-Ldec)) {
-    q = 1;
-    for (j = deg_lambda; j > 0; j--){
-      if (reg[j] != A0) {
-	reg[j] = modnn(reg[j] + j);
-	q ^= Alpha_to[reg[j]];
-      }
-    }
-    if (q != 0)
-      continue;
-    /* store root (index-form) and error location number */
-    root[count] = i;
-    loc[count] = k;
-    /* If we've already found max possible roots,
-     * abort the search to save time
-     */
-    if(++count == deg_lambda)
-      break;
-  }
-  if (deg_lambda != count) {
-    /*
-     * deg(lambda) unequal to number of roots => uncorrectable
-     * error detected
-     */
-    count = -1;
-    goto finish;
-  }
-  /*
-   * Compute err+eras evaluator poly omega(x) = s(x)*lambda(x) (modulo
-   * x**(NN-KK)). in index form. Also find deg(omega).
-   */
-  deg_omega = 0;
-  for (i = 0; i < NN-KK;i++){
-    tmp = 0;
-    j = (deg_lambda < i) ? deg_lambda : i;
-    for(;j >= 0; j--){
-      if ((s[i + 1 - j] != A0) && (lambda[j] != A0))
-	tmp ^= Alpha_to[modnn(s[i + 1 - j] + lambda[j])];
-    }
-    if(tmp != 0)
-      deg_omega = i;
-    omega[i] = Index_of[tmp];
-  }
-  omega[NN-KK] = A0;
-
-  /*
-   * Compute error values in poly-form. num1 = omega(inv(X(l))), num2 =
-   * inv(X(l))**(B0-1) and den = lambda_pr(inv(X(l))) all in poly-form
-   */
-  for (j = count-1; j >=0; j--) {
-    num1 = 0;
-    for (i = deg_omega; i >= 0; i--) {
-      if (omega[i] != A0)
-	num1  ^= Alpha_to[modnn(omega[i] + i * root[j])];
-    }
-    num2 = Alpha_to[modnn(root[j] * (B0 - 1) + NN)];
-    den = 0;
-
-    /* lambda[i+1] for i even is the formal derivative lambda_pr of lambda[i] */
-    for (i = min(deg_lambda,NN-KK-1) & ~1; i >= 0; i -=2) {
-      if(lambda[i+1] != A0)
-	den ^= Alpha_to[modnn(lambda[i+1] + i * root[j])];
-    }
-    if (den == 0) {
-#if DEBUG_ECC >= 1
-      printf("\n ERROR: denominator = 0\n");
-#endif
-      /* Convert to dual- basis */
-      count = -1;
-      goto finish;
-    }
-    /* Apply error to data */
-    if (num1 != 0) {
-        eras_val[j] = Alpha_to[modnn(Index_of[num1] + Index_of[num2] + NN - Index_of[den])];
-    } else {
-        eras_val[j] = 0;
-    }
-  }
- finish:
-  for(i=0;i<count;i++)
-      eras_pos[i] = loc[i];
-  return count;
-}
-
-/***************************************************************************/
-/* The DOC specific code begins here */
-
-#define SECTOR_SIZE 512
-/* The sector bytes are packed into NB_DATA MM bits words */
-#define NB_DATA (((SECTOR_SIZE + 1) * 8 + 6) / MM)
-
-/*
- * Correct the errors in 'sector[]' by using 'ecc1[]' which is the
- * content of the feedback shift register applyied to the sector and
- * the ECC. Return the number of errors corrected (and correct them in
- * sector), or -1 if error
- */
-int doc_decode_ecc(unsigned char sector[SECTOR_SIZE], unsigned char ecc1[6])
-{
-    int parity, i, nb_errors;
-    gf bb[NN - KK + 1];
-    gf error_val[NN-KK];
-    int error_pos[NN-KK], pos, bitpos, index, val;
-    dtype *Alpha_to, *Index_of;
-
-    /* init log and exp tables here to save memory. However, it is slower */
-    Alpha_to = kmalloc((NN + 1) * sizeof(dtype), GFP_KERNEL);
-    if (!Alpha_to)
-        return -1;
-
-    Index_of = kmalloc((NN + 1) * sizeof(dtype), GFP_KERNEL);
-    if (!Index_of) {
-        kfree(Alpha_to);
-        return -1;
-    }
-
-    generate_gf(Alpha_to, Index_of);
-
-    parity = ecc1[1];
-
-    bb[0] =  (ecc1[4] & 0xff) | ((ecc1[5] & 0x03) << 8);
-    bb[1] = ((ecc1[5] & 0xfc) >> 2) | ((ecc1[2] & 0x0f) << 6);
-    bb[2] = ((ecc1[2] & 0xf0) >> 4) | ((ecc1[3] & 0x3f) << 4);
-    bb[3] = ((ecc1[3] & 0xc0) >> 6) | ((ecc1[0] & 0xff) << 2);
-
-    nb_errors = eras_dec_rs(Alpha_to, Index_of, bb,
-                            error_val, error_pos, 0);
-    if (nb_errors <= 0)
-        goto the_end;
-
-    /* correct the errors */
-    for(i=0;i<nb_errors;i++) {
-        pos = error_pos[i];
-        if (pos >= NB_DATA && pos < KK) {
-            nb_errors = -1;
-            goto the_end;
-        }
-        if (pos < NB_DATA) {
-            /* extract bit position (MSB first) */
-            pos = 10 * (NB_DATA - 1 - pos) - 6;
-            /* now correct the following 10 bits. At most two bytes
-               can be modified since pos is even */
-            index = (pos >> 3) ^ 1;
-            bitpos = pos & 7;
-            if ((index >= 0 && index < SECTOR_SIZE) ||
-                index == (SECTOR_SIZE + 1)) {
-                val = error_val[i] >> (2 + bitpos);
-                parity ^= val;
-                if (index < SECTOR_SIZE)
-                    sector[index] ^= val;
-            }
-            index = ((pos >> 3) + 1) ^ 1;
-            bitpos = (bitpos + 10) & 7;
-            if (bitpos == 0)
-                bitpos = 8;
-            if ((index >= 0 && index < SECTOR_SIZE) ||
-                index == (SECTOR_SIZE + 1)) {
-                val = error_val[i] << (8 - bitpos);
-                parity ^= val;
-                if (index < SECTOR_SIZE)
-                    sector[index] ^= val;
-            }
-        }
-    }
-
-    /* use parity to test extra errors */
-    if ((parity & 0xff) != 0)
-        nb_errors = -1;
-
- the_end:
-    kfree(Alpha_to);
-    kfree(Index_of);
-    return nb_errors;
-}
-
-EXPORT_SYMBOL_GPL(doc_decode_ecc);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Fabrice Bellard <fabrice.bellard@netgem.com>");
-MODULE_DESCRIPTION("ECC code for correcting errors detected by DiskOnChip 2000 and Millennium ECC hardware");

drivers/mtd/devices/docg3.c

@@ -123,7 +123,7 @@ static inline void doc_flash_address(struct docg3 *docg3, u8 addr)
 	doc_writeb(docg3, addr, DOC_FLASHADDRESS);
 }
 
-static char const *part_probes[] = { "cmdlinepart", "saftlpart", NULL };
+static char const * const part_probes[] = { "cmdlinepart", "saftlpart", NULL };
 
 static int doc_register_readb(struct docg3 *docg3, int reg)
 {
@@ -2144,18 +2144,7 @@ static struct platform_driver g3_driver = {
 	.remove		= __exit_p(docg3_release),
 };
 
-static int __init docg3_init(void)
-{
-	return platform_driver_probe(&g3_driver, docg3_probe);
-}
-module_init(docg3_init);
-
-
-static void __exit docg3_exit(void)
-{
-	platform_driver_unregister(&g3_driver);
-}
-module_exit(docg3_exit);
+module_platform_driver_probe(g3_driver, docg3_probe);
 
 MODULE_LICENSE("GPL");
 MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>");

drivers/mtd/devices/docprobe.c

-
-/* Linux driver for Disk-On-Chip devices			*/
-/* Probe routines common to all DoC devices			*/
-/* (C) 1999 Machine Vision Holdings, Inc.			*/
-/* (C) 1999-2003 David Woodhouse <dwmw2@infradead.org>		*/
-
-
-/* DOC_PASSIVE_PROBE:
-   In order to ensure that the BIOS checksum is correct at boot time, and
-   hence that the onboard BIOS extension gets executed, the DiskOnChip
-   goes into reset mode when it is read sequentially: all registers
-   return 0xff until the chip is woken up again by writing to the
-   DOCControl register.
-
-   Unfortunately, this means that the probe for the DiskOnChip is unsafe,
-   because one of the first things it does is write to where it thinks
-   the DOCControl register should be - which may well be shared memory
-   for another device. I've had machines which lock up when this is
-   attempted. Hence the possibility to do a passive probe, which will fail
-   to detect a chip in reset mode, but is at least guaranteed not to lock
-   the machine.
-
-   If you have this problem, uncomment the following line:
-#define DOC_PASSIVE_PROBE
-*/
-
-
-/* DOC_SINGLE_DRIVER:
-   Millennium driver has been merged into DOC2000 driver.
-
-   The old Millennium-only driver has been retained just in case there
-   are problems with the new code. If the combined driver doesn't work
-   for you, you can try the old one by undefining DOC_SINGLE_DRIVER
-   below and also enabling it in your configuration. If this fixes the
-   problems, please send a report to the MTD mailing list at
-   <linux-mtd@lists.infradead.org>.
-*/
-#define DOC_SINGLE_DRIVER
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/types.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/doc2000.h>
-
-
-static unsigned long doc_config_location = CONFIG_MTD_DOCPROBE_ADDRESS;
-module_param(doc_config_location, ulong, 0);
-MODULE_PARM_DESC(doc_config_location, "Physical memory address at which to probe for DiskOnChip");
-
-static unsigned long __initdata doc_locations[] = {
-#if defined (__alpha__) || defined(__i386__) || defined(__x86_64__)
-#ifdef CONFIG_MTD_DOCPROBE_HIGH
-	0xfffc8000, 0xfffca000, 0xfffcc000, 0xfffce000,
-	0xfffd0000, 0xfffd2000, 0xfffd4000, 0xfffd6000,
-	0xfffd8000, 0xfffda000, 0xfffdc000, 0xfffde000,
-	0xfffe0000, 0xfffe2000, 0xfffe4000, 0xfffe6000,
-	0xfffe8000, 0xfffea000, 0xfffec000, 0xfffee000,
-#else /*  CONFIG_MTD_DOCPROBE_HIGH */
-	0xc8000, 0xca000, 0xcc000, 0xce000,
-	0xd0000, 0xd2000, 0xd4000, 0xd6000,
-	0xd8000, 0xda000, 0xdc000, 0xde000,
-	0xe0000, 0xe2000, 0xe4000, 0xe6000,
-	0xe8000, 0xea000, 0xec000, 0xee000,
-#endif /*  CONFIG_MTD_DOCPROBE_HIGH */
-#endif
-	0xffffffff };
-
-/* doccheck: Probe a given memory window to see if there's a DiskOnChip present */
-
-static inline int __init doccheck(void __iomem *potential, unsigned long physadr)
-{
-	void __iomem *window=potential;
-	unsigned char tmp, tmpb, tmpc, ChipID;
-#ifndef DOC_PASSIVE_PROBE
-	unsigned char tmp2;
-#endif
-
-	/* Routine copied from the Linux DOC driver */
-
-#ifdef CONFIG_MTD_DOCPROBE_55AA
-	/* Check for 0x55 0xAA signature at beginning of window,
-	   this is no longer true once we remove the IPL (for Millennium */
-	if (ReadDOC(window, Sig1) != 0x55 || ReadDOC(window, Sig2) != 0xaa)
-		return 0;
-#endif /* CONFIG_MTD_DOCPROBE_55AA */
-
-#ifndef DOC_PASSIVE_PROBE
-	/* It's not possible to cleanly detect the DiskOnChip - the
-	 * bootup procedure will put the device into reset mode, and
-	 * it's not possible to talk to it without actually writing
-	 * to the DOCControl register. So we store the current contents
-	 * of the DOCControl register's location, in case we later decide
-	 * that it's not a DiskOnChip, and want to put it back how we
-	 * found it.
-	 */
-	tmp2 = ReadDOC(window, DOCControl);
-
-	/* Reset the DiskOnChip ASIC */
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET,
-		 window, DOCControl);
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_RESET,
-		 window, DOCControl);
-
-	/* Enable the DiskOnChip ASIC */
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL,
-		 window, DOCControl);
-	WriteDOC(DOC_MODE_CLR_ERR | DOC_MODE_MDWREN | DOC_MODE_NORMAL,
-		 window, DOCControl);
-#endif /* !DOC_PASSIVE_PROBE */
-
-	/* We need to read the ChipID register four times. For some
-	   newer DiskOnChip 2000 units, the first three reads will
-	   return the DiskOnChip Millennium ident. Don't ask. */
-	ChipID = ReadDOC(window, ChipID);
-
-	switch (ChipID) {
-	case DOC_ChipID_Doc2k:
-		/* Check the TOGGLE bit in the ECC register */
-		tmp  = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT;
-		tmpb = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT;
-		tmpc = ReadDOC(window, 2k_ECCStatus) & DOC_TOGGLE_BIT;
-		if (tmp != tmpb && tmp == tmpc)
-				return ChipID;
-		break;
-
-	case DOC_ChipID_DocMil:
-		/* Check for the new 2000 with Millennium ASIC */
-		ReadDOC(window, ChipID);
-		ReadDOC(window, ChipID);
-		if (ReadDOC(window, ChipID) != DOC_ChipID_DocMil)
-			ChipID = DOC_ChipID_Doc2kTSOP;
-
-		/* Check the TOGGLE bit in the ECC register */
-		tmp  = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT;
-		tmpb = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT;
-		tmpc = ReadDOC(window, ECCConf) & DOC_TOGGLE_BIT;
-		if (tmp != tmpb && tmp == tmpc)
-				return ChipID;
-		break;
-
-	case DOC_ChipID_DocMilPlus16:
-	case DOC_ChipID_DocMilPlus32:
-	case 0:
-		/* Possible Millennium+, need to do more checks */
-#ifndef DOC_PASSIVE_PROBE
-		/* Possibly release from power down mode */
-		for (tmp = 0; (tmp < 4); tmp++)
-			ReadDOC(window, Mplus_Power);
-
-		/* Reset the DiskOnChip ASIC */
-		tmp = DOC_MODE_RESET | DOC_MODE_MDWREN | DOC_MODE_RST_LAT |
-			DOC_MODE_BDECT;
-		WriteDOC(tmp, window, Mplus_DOCControl);
-		WriteDOC(~tmp, window, Mplus_CtrlConfirm);
-
-		mdelay(1);
-		/* Enable the DiskOnChip ASIC */
-		tmp = DOC_MODE_NORMAL | DOC_MODE_MDWREN | DOC_MODE_RST_LAT |
-			DOC_MODE_BDECT;
-		WriteDOC(tmp, window, Mplus_DOCControl);
-		WriteDOC(~tmp, window, Mplus_CtrlConfirm);
-		mdelay(1);
-#endif /* !DOC_PASSIVE_PROBE */
-
-		ChipID = ReadDOC(window, ChipID);
-
-		switch (ChipID) {
-		case DOC_ChipID_DocMilPlus16:
-		case DOC_ChipID_DocMilPlus32:
-			/* Check the TOGGLE bit in the toggle register */
-			tmp  = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT;
-			tmpb = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT;
-			tmpc = ReadDOC(window, Mplus_Toggle) & DOC_TOGGLE_BIT;
-			if (tmp != tmpb && tmp == tmpc)
-					return ChipID;
-		default:
-			break;
-		}
-		/* FALL TRHU */
-
-	default:
-
-#ifdef CONFIG_MTD_DOCPROBE_55AA
-		printk(KERN_DEBUG "Possible DiskOnChip with unknown ChipID %2.2X found at 0x%lx\n",
-		       ChipID, physadr);
-#endif
-#ifndef DOC_PASSIVE_PROBE
-		/* Put back the contents of the DOCControl register, in case it's not
-		 * actually a DiskOnChip.
-		 */
-		WriteDOC(tmp2, window, DOCControl);
-#endif
-		return 0;
-	}
-
-	printk(KERN_WARNING "DiskOnChip failed TOGGLE test, dropping.\n");
-
-#ifndef DOC_PASSIVE_PROBE
-	/* Put back the contents of the DOCControl register: it's not a DiskOnChip */
-	WriteDOC(tmp2, window, DOCControl);
-#endif
-	return 0;
-}
-
-static int docfound;
-
-extern void DoC2k_init(struct mtd_info *);
-extern void DoCMil_init(struct mtd_info *);
-extern void DoCMilPlus_init(struct mtd_info *);
-
-static void __init DoC_Probe(unsigned long physadr)
-{
-	void __iomem *docptr;
-	struct DiskOnChip *this;
-	struct mtd_info *mtd;
-	int ChipID;
-	char namebuf[15];
-	char *name = namebuf;
-	void (*initroutine)(struct mtd_info *) = NULL;
-
-	docptr = ioremap(physadr, DOC_IOREMAP_LEN);
-
-	if (!docptr)
-		return;
-
-	if ((ChipID = doccheck(docptr, physadr))) {
-		if (ChipID == DOC_ChipID_Doc2kTSOP) {
-			/* Remove this at your own peril. The hardware driver works but nothing prevents you from erasing bad blocks */
-			printk(KERN_NOTICE "Refusing to drive DiskOnChip 2000 TSOP until Bad Block Table is correctly supported by INFTL\n");
-			iounmap(docptr);
-			return;
-		}
-		docfound = 1;
-		mtd = kzalloc(sizeof(struct DiskOnChip) + sizeof(struct mtd_info), GFP_KERNEL);
-		if (!mtd) {
-			printk(KERN_WARNING "Cannot allocate memory for data structures. Dropping.\n");
-			iounmap(docptr);
-			return;
-		}
-
-		this = (struct DiskOnChip *)(&mtd[1]);
-		mtd->priv = this;
-		this->virtadr = docptr;
-		this->physadr = physadr;
-		this->ChipID = ChipID;
-		sprintf(namebuf, "with ChipID %2.2X", ChipID);
-
-		switch(ChipID) {
-		case DOC_ChipID_Doc2kTSOP:
-			name="2000 TSOP";
-			initroutine = symbol_request(DoC2k_init);
-			break;
-
-		case DOC_ChipID_Doc2k:
-			name="2000";
-			initroutine = symbol_request(DoC2k_init);
-			break;
-
-		case DOC_ChipID_DocMil:
-			name="Millennium";
-#ifdef DOC_SINGLE_DRIVER
-			initroutine = symbol_request(DoC2k_init);
-#else
-			initroutine = symbol_request(DoCMil_init);
-#endif /* DOC_SINGLE_DRIVER */
-			break;
-
-		case DOC_ChipID_DocMilPlus16:
-		case DOC_ChipID_DocMilPlus32:
-			name="MillenniumPlus";
-			initroutine = symbol_request(DoCMilPlus_init);
-			break;
-		}
-
-		if (initroutine) {
-			(*initroutine)(mtd);
-			symbol_put_addr(initroutine);
-			return;
-		}
-		printk(KERN_NOTICE "Cannot find driver for DiskOnChip %s at 0x%lX\n", name, physadr);
-		kfree(mtd);
-	}
-	iounmap(docptr);
-}
-
-
-/****************************************************************************
- *
- * Module stuff
- *
- ****************************************************************************/
-
-static int __init init_doc(void)
-{
-	int i;
-
-	if (doc_config_location) {
-		printk(KERN_INFO "Using configured DiskOnChip probe address 0x%lx\n", doc_config_location);
-		DoC_Probe(doc_config_location);
-	} else {
-		for (i=0; (doc_locations[i] != 0xffffffff); i++) {
-			DoC_Probe(doc_locations[i]);
-		}
-	}
-	/* No banner message any more. Print a message if no DiskOnChip
-	   found, so the user knows we at least tried. */
-	if (!docfound)
-		printk(KERN_INFO "No recognised DiskOnChip devices found\n");
-	return -EAGAIN;
-}
-
-module_init(init_doc);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>");
-MODULE_DESCRIPTION("Probe code for DiskOnChip 2000 and Millennium devices");
-

drivers/mtd/devices/elm.c

@@ -81,14 +81,21 @@ static u32 elm_read_reg(struct elm_info *info, int offset)
  * @dev:	ELM device
  * @bch_type:	Type of BCH ecc
  */
-void elm_config(struct device *dev, enum bch_ecc bch_type)
+int elm_config(struct device *dev, enum bch_ecc bch_type)
 {
 	u32 reg_val;
 	struct elm_info *info = dev_get_drvdata(dev);
 
+	if (!info) {
+		dev_err(dev, "Unable to configure elm - device not probed?\n");
+		return -ENODEV;
+	}
+
 	reg_val = (bch_type & ECC_BCH_LEVEL_MASK) | (ELM_ECC_SIZE << 16);
 	elm_write_reg(info, ELM_LOCATION_CONFIG, reg_val);
 	info->bch_type = bch_type;
+
+	return 0;
 }
 EXPORT_SYMBOL(elm_config);
 

drivers/mtd/devices/m25p80.c

@@ -681,6 +681,7 @@ struct flash_info {
 	u16		flags;
 #define	SECT_4K		0x01		/* OPCODE_BE_4K works uniformly */
 #define	M25P_NO_ERASE	0x02		/* No erase command needed */
+#define	SST_WRITE	0x04		/* use SST byte programming */
 };
 
 #define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
@@ -728,6 +729,7 @@ static const struct spi_device_id m25p_ids[] = {
 	{ "en25q32b", INFO(0x1c3016, 0, 64 * 1024,  64, 0) },
 	{ "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) },
 	{ "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) },
+	{ "en25qh256", INFO(0x1c7019, 0, 64 * 1024, 512, 0) },
 
 	/* Everspin */
 	{ "mr25h256", CAT25_INFO(  32 * 1024, 1, 256, 2) },
@@ -740,7 +742,6 @@ static const struct spi_device_id m25p_ids[] = {
 	{ "160s33b",  INFO(0x898911, 0, 64 * 1024,  32, 0) },
 	{ "320s33b",  INFO(0x898912, 0, 64 * 1024,  64, 0) },
 	{ "640s33b",  INFO(0x898913, 0, 64 * 1024, 128, 0) },
-	{ "n25q064",  INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
 
 	/* Macronix */
 	{ "mx25l2005a",  INFO(0xc22012, 0, 64 * 1024,   4, SECT_4K) },
@@ -753,8 +754,10 @@ static const struct spi_device_id m25p_ids[] = {
 	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
 	{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
 	{ "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
+	{ "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, 0) },
 
 	/* Micron */
+	{ "n25q064",  INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
 	{ "n25q128a11",  INFO(0x20bb18, 0, 64 * 1024, 256, 0) },
 	{ "n25q128a13",  INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
 	{ "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) },
@@ -781,14 +784,15 @@ static const struct spi_device_id m25p_ids[] = {
 	{ "s25fl064k",  INFO(0xef4017,      0,  64 * 1024, 128, SECT_4K) },
 
 	/* SST -- large erase sizes are "overlays", "sectors" are 4K */
-	{ "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K) },
-	{ "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K) },
-	{ "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K) },
-	{ "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K) },
-	{ "sst25wf512",  INFO(0xbf2501, 0, 64 * 1024,  1, SECT_4K) },
-	{ "sst25wf010",  INFO(0xbf2502, 0, 64 * 1024,  2, SECT_4K) },
-	{ "sst25wf020",  INFO(0xbf2503, 0, 64 * 1024,  4, SECT_4K) },
-	{ "sst25wf040",  INFO(0xbf2504, 0, 64 * 1024,  8, SECT_4K) },
+	{ "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024,  8, SECT_4K | SST_WRITE) },
+	{ "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) },
+	{ "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) },
+	{ "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) },
+	{ "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) },
+	{ "sst25wf512",  INFO(0xbf2501, 0, 64 * 1024,  1, SECT_4K | SST_WRITE) },
+	{ "sst25wf010",  INFO(0xbf2502, 0, 64 * 1024,  2, SECT_4K | SST_WRITE) },
+	{ "sst25wf020",  INFO(0xbf2503, 0, 64 * 1024,  4, SECT_4K | SST_WRITE) },
+	{ "sst25wf040",  INFO(0xbf2504, 0, 64 * 1024,  8, SECT_4K | SST_WRITE) },
 
 	/* ST Microelectronics -- newer production may have feature updates */
 	{ "m25p05",  INFO(0x202010,  0,  32 * 1024,   2, 0) },
@@ -838,6 +842,7 @@ static const struct spi_device_id m25p_ids[] = {
 	{ "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
 	{ "w25q80", INFO(0xef5014, 0, 64 * 1024,  16, SECT_4K) },
 	{ "w25q80bl", INFO(0xef4014, 0, 64 * 1024,  16, SECT_4K) },
+	{ "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
 	{ "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K) },
 
 	/* Catalyst / On Semiconductor -- non-JEDEC */
@@ -1000,7 +1005,7 @@ static int m25p_probe(struct spi_device *spi)
 	}
 
 	/* sst flash chips use AAI word program */
-	if (JEDEC_MFR(info->jedec_id) == CFI_MFR_SST)
+	if (info->flags & SST_WRITE)
 		flash->mtd._write = sst_write;
 	else
 		flash->mtd._write = m25p80_write;

drivers/mtd/devices/mtd_dataflash.c

@@ -105,8 +105,6 @@ static const struct of_device_id dataflash_dt_ids[] = {
 	{ .compatible = "atmel,dataflash", },
 	{ /* sentinel */ }
 };
-#else
-#define dataflash_dt_ids NULL
 #endif
 
 /* ......................................................................... */
@@ -914,7 +912,7 @@ static struct spi_driver dataflash_driver = {
 	.driver = {
 		.name		= "mtd_dataflash",
 		.owner		= THIS_MODULE,
-		.of_match_table = dataflash_dt_ids,
+		.of_match_table = of_match_ptr(dataflash_dt_ids),
 	},
 
 	.probe		= dataflash_probe,

drivers/mtd/maps/Kconfig

@@ -249,22 +249,6 @@ config MTD_LANTIQ
 	help
 	  Support for NOR flash attached to the Lantiq SoC's External Bus Unit.
 
-config MTD_DILNETPC
-	tristate "CFI Flash device mapped on DIL/Net PC"
-	depends on X86 && MTD_CFI_INTELEXT && BROKEN
-	help
-	  MTD map driver for SSV DIL/Net PC Boards "DNP" and "ADNP".
-	  For details, see <http://www.ssv-embedded.de/ssv/pc104/p169.htm>
- 	  and <http://www.ssv-embedded.de/ssv/pc104/p170.htm>
-
-config MTD_DILNETPC_BOOTSIZE
-	hex "Size of DIL/Net PC flash boot partition"
-	depends on MTD_DILNETPC
-	default "0x80000"
-	help
-	  The amount of space taken up by the kernel or Etherboot
-	  on the DIL/Net PC flash chips.
-
 config MTD_L440GX
 	tristate "BIOS flash chip on Intel L440GX boards"
 	depends on X86 && MTD_JEDECPROBE
@@ -274,42 +258,6 @@ config MTD_L440GX
 
 	  BE VERY CAREFUL.
 
-config MTD_TQM8XXL
-	tristate "CFI Flash device mapped on TQM8XXL"
-	depends on MTD_CFI && TQM8xxL
-	help
-	  The TQM8xxL PowerPC board has up to two banks of CFI-compliant
-	  chips, currently uses AMD one. This 'mapping' driver supports
-	  that arrangement, allowing the CFI probe and command set driver
-	  code to communicate with the chips on the TQM8xxL board. More at
-	  <http://www.denx.de/wiki/PPCEmbedded/>.
-
-config MTD_RPXLITE
-	tristate "CFI Flash device mapped on RPX Lite or CLLF"
-	depends on MTD_CFI && (RPXCLASSIC || RPXLITE)
-	help
-	  The RPXLite PowerPC board has CFI-compliant chips mapped in
-	  a strange sparse mapping. This 'mapping' driver supports that
-	  arrangement, allowing the CFI probe and command set driver code
-	  to communicate with the chips on the RPXLite board. More at
-	  <http://www.embeddedplanet.com/>.
-
-config MTD_MBX860
-	tristate "System flash on MBX860 board"
-	depends on MTD_CFI && MBX
-	help
-	  This enables access routines for the flash chips on the Motorola
-	  MBX860 board. If you have one of these boards and would like
-	  to use the flash chips on it, say 'Y'.
-
-config MTD_DBOX2
-	tristate "CFI Flash device mapped on D-Box2"
-	depends on DBOX2 && MTD_CFI_INTELSTD && MTD_CFI_INTELEXT && MTD_CFI_AMDSTD
-	help
-	  This enables access routines for the flash chips on the Nokia/Sagem
-	  D-Box 2 board. If you have one of these boards and would like to use
-	  the flash chips on it, say 'Y'.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
@@ -349,15 +297,6 @@ config MTD_IXP4XX
 	  IXDP425 and Coyote. If you have an IXP4xx based board and
 	  would like to use the flash chips on it, say 'Y'.
 
-config MTD_IXP2000
-	tristate "CFI Flash device mapped on Intel IXP2000 based systems"
-	depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP2000
-	help
-	  This enables MTD access to flash devices on platforms based
-	  on Intel's IXP2000 family of network processors. If you have an
-	  IXP2000 based board and would like to use the flash chips on it,
-	  say 'Y'.
-
 config MTD_AUTCPU12
 	bool "NV-RAM mapping AUTCPU12 board"
 	depends on ARCH_AUTCPU12
@@ -372,13 +311,6 @@ config MTD_IMPA7
 	  This enables access to the NOR Flash on the impA7 board of
 	  implementa GmbH. If you have such a board, say 'Y' here.
 
-config MTD_H720X
-	tristate "Hynix evaluation board mappings"
-	depends on MTD_CFI && ( ARCH_H7201 || ARCH_H7202 )
-	help
-	  This enables access to the flash chips on the Hynix evaluation boards.
-	  If you have such a board, say 'Y'.
-
 # This needs CFI or JEDEC, depending on the cards found.
 config MTD_PCI
 	tristate "PCI MTD driver"
@@ -433,15 +365,6 @@ config MTD_UCLINUX
 	help
 	  Map driver to support image based filesystems for uClinux.
 
-config MTD_DMV182
-        tristate "Map driver for Dy-4 SVME/DMV-182 board."
-        depends on DMV182
-	select MTD_MAP_BANK_WIDTH_32
-	select MTD_CFI_I8
-	select MTD_CFI_AMDSTD
-        help
-          Map driver for Dy-4 SVME/DMV-182 board.
-
 config MTD_INTEL_VR_NOR
 	tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0"
 	depends on PCI

drivers/mtd/maps/Makefile

@@ -9,7 +9,6 @@ endif
 # Chip mappings
 obj-$(CONFIG_MTD_CFI_FLAGADM)	+= cfi_flagadm.o
 obj-$(CONFIG_MTD_DC21285)	+= dc21285.o
-obj-$(CONFIG_MTD_DILNETPC)	+= dilnetpc.o
 obj-$(CONFIG_MTD_L440GX)	+= l440gx.o
 obj-$(CONFIG_MTD_AMD76XROM)	+= amd76xrom.o
 obj-$(CONFIG_MTD_ESB2ROM)	+= esb2rom.o
@@ -17,15 +16,12 @@ obj-$(CONFIG_MTD_ICHXROM)	+= ichxrom.o
 obj-$(CONFIG_MTD_CK804XROM)	+= ck804xrom.o
 obj-$(CONFIG_MTD_TSUNAMI)	+= tsunami_flash.o
 obj-$(CONFIG_MTD_PXA2XX)	+= pxa2xx-flash.o
-obj-$(CONFIG_MTD_MBX860)	+= mbx860.o
 obj-$(CONFIG_MTD_OCTAGON)	+= octagon-5066.o
 obj-$(CONFIG_MTD_PHYSMAP)	+= physmap.o
 obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
 obj-$(CONFIG_MTD_PISMO)		+= pismo.o
 obj-$(CONFIG_MTD_PMC_MSP_EVM)   += pmcmsp-flash.o
 obj-$(CONFIG_MTD_PCMCIA)	+= pcmciamtd.o
-obj-$(CONFIG_MTD_RPXLITE)	+= rpxlite.o
-obj-$(CONFIG_MTD_TQM8XXL)	+= tqm8xxl.o
 obj-$(CONFIG_MTD_SA1100)	+= sa1100-flash.o
 obj-$(CONFIG_MTD_SBC_GXX)	+= sbc_gxx.o
 obj-$(CONFIG_MTD_SC520CDP)	+= sc520cdp.o
@@ -34,7 +30,6 @@ obj-$(CONFIG_MTD_TS5500)	+= ts5500_flash.o
 obj-$(CONFIG_MTD_SUN_UFLASH)	+= sun_uflash.o
 obj-$(CONFIG_MTD_VMAX)		+= vmax301.o
 obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx200_docflash.o
-obj-$(CONFIG_MTD_DBOX2)		+= dbox2-flash.o
 obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
 obj-$(CONFIG_MTD_PCI)		+= pci.o
 obj-$(CONFIG_MTD_AUTCPU12)	+= autcpu12-nvram.o
@@ -42,10 +37,7 @@ obj-$(CONFIG_MTD_IMPA7)		+= impa7.o
 obj-$(CONFIG_MTD_UCLINUX)	+= uclinux.o
 obj-$(CONFIG_MTD_NETtel)	+= nettel.o
 obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
-obj-$(CONFIG_MTD_H720X)		+= h720x-flash.o
 obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
-obj-$(CONFIG_MTD_IXP2000)	+= ixp2000.o
-obj-$(CONFIG_MTD_DMV182)	+= dmv182.o
 obj-$(CONFIG_MTD_PLATRAM)	+= plat-ram.o
 obj-$(CONFIG_MTD_INTEL_VR_NOR)	+= intel_vr_nor.o
 obj-$(CONFIG_MTD_BFIN_ASYNC)	+= bfin-async-flash.o

drivers/mtd/maps/bfin-async-flash.c

@@ -122,7 +122,8 @@ static void bfin_flash_copy_to(struct map_info *map, unsigned long to, const voi
 	switch_back(state);
 }
 
-static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", NULL };
+static const char * const part_probe_types[] = {
+	"cmdlinepart", "RedBoot", NULL };
 
 static int bfin_flash_probe(struct platform_device *pdev)
 {

drivers/mtd/maps/ck804xrom.c

@@ -308,8 +308,7 @@ static int ck804xrom_init_one(struct pci_dev *pdev,
 
  out:
 	/* Free any left over map structures */
-	if (map)
-		kfree(map);
+	kfree(map);
 
 	/* See if I have any map structures */
 	if (list_empty(&window->maps)) {

drivers/mtd/maps/dbox2-flash.c

-/*
- * D-Box 2 flash driver
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <asm/io.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <linux/errno.h>
-
-/* partition_info gives details on the logical partitions that the split the
- * single flash device into. If the size if zero we use up to the end of the
- * device. */
-static struct mtd_partition partition_info[]= {
-	{
-	.name		= "BR bootloader",
-	.size		= 128 * 1024,
-	.offset		= 0,
-	.mask_flags	= MTD_WRITEABLE
-	},
-	{
-	.name		= "FLFS (U-Boot)",
-	.size		= 128 * 1024,
-	.offset		= MTDPART_OFS_APPEND,
-	.mask_flags	= 0
-	},
-	{
-	.name		= "Root (SquashFS)",
-	.size		= 7040 * 1024,
-	.offset		= MTDPART_OFS_APPEND,
-	.mask_flags	= 0
-	},
-	{
-	.name		= "var (JFFS2)",
-	.size		= 896 * 1024,
-	.offset		= MTDPART_OFS_APPEND,
-	.mask_flags	= 0
-	},
-	{
-	.name		= "Flash without bootloader",
-	.size		= MTDPART_SIZ_FULL,
-	.offset		= 128 * 1024,
-	.mask_flags	= 0
-	},
-	{
-	.name		= "Complete Flash",
-	.size		= MTDPART_SIZ_FULL,
-	.offset		= 0,
-	.mask_flags	= MTD_WRITEABLE
-	}
-};
-
-#define NUM_PARTITIONS ARRAY_SIZE(partition_info)
-
-#define WINDOW_ADDR 0x10000000
-#define WINDOW_SIZE 0x800000
-
-static struct mtd_info *mymtd;
-
-
-struct map_info dbox2_flash_map = {
-	.name		= "D-Box 2 flash memory",
-	.size		= WINDOW_SIZE,
-	.bankwidth	= 4,
-	.phys		= WINDOW_ADDR,
-};
-
-static int __init init_dbox2_flash(void)
-{
-       	printk(KERN_NOTICE "D-Box 2 flash driver (size->0x%X mem->0x%X)\n", WINDOW_SIZE, WINDOW_ADDR);
-	dbox2_flash_map.virt = ioremap(WINDOW_ADDR, WINDOW_SIZE);
-
-	if (!dbox2_flash_map.virt) {
-		printk("Failed to ioremap\n");
-		return -EIO;
-	}
-	simple_map_init(&dbox2_flash_map);
-
-	// Probe for dual Intel 28F320 or dual AMD
-	mymtd = do_map_probe("cfi_probe", &dbox2_flash_map);
-	if (!mymtd) {
-	    // Probe for single Intel 28F640
-	    dbox2_flash_map.bankwidth = 2;
-
-	    mymtd = do_map_probe("cfi_probe", &dbox2_flash_map);
-	}
-
-	if (mymtd) {
-		mymtd->owner = THIS_MODULE;
-
-                /* Create MTD devices for each partition. */
-		mtd_device_register(mymtd, partition_info, NUM_PARTITIONS);
-
-		return 0;
-	}
-
-	iounmap((void *)dbox2_flash_map.virt);
-	return -ENXIO;
-}
-
-static void __exit cleanup_dbox2_flash(void)
-{
-	if (mymtd) {
-		mtd_device_unregister(mymtd);
-		map_destroy(mymtd);
-	}
-	if (dbox2_flash_map.virt) {
-		iounmap((void *)dbox2_flash_map.virt);
-		dbox2_flash_map.virt = 0;
-	}
-}
-
-module_init(init_dbox2_flash);
-module_exit(cleanup_dbox2_flash);
-
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Kári Davíðsson <kd@flaga.is>, Bastian Blank <waldi@tuxbox.org>, Alexander Wild <wild@te-elektronik.com>");
-MODULE_DESCRIPTION("MTD map driver for D-Box 2 board");

drivers/mtd/maps/dc21285.c

@@ -143,9 +143,8 @@ static struct map_info dc21285_map = {
 	.copy_from = dc21285_copy_from,
 };
 
-
 /* Partition stuff */
-static const char *probes[] = { "RedBoot", "cmdlinepart", NULL };
+static const char * const probes[] = { "RedBoot", "cmdlinepart", NULL };
 
 static int __init init_dc21285(void)
 {

drivers/mtd/maps/dmv182.c

-
-/*
- * drivers/mtd/maps/dmv182.c
- *
- * Flash map driver for the Dy4 SVME182 board
- *
- * Copyright 2003-2004, TimeSys Corporation
- *
- * Based on the SVME181 flash map, by Tom Nelson, Dot4, Inc. for TimeSys Corp.
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <asm/io.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <linux/errno.h>
-
-/*
- * This driver currently handles only the 16MiB user flash bank 1 on the
- * board.  It does not provide access to bank 0 (contains the Dy4 FFW), bank 2
- * (VxWorks boot), or the optional 48MiB expansion flash.
- *
- * scott.wood@timesys.com: On the newer boards with 128MiB flash, it
- * now supports the first 96MiB (the boot flash bank containing FFW
- * is excluded).  The VxWorks loader is in partition 1.
- */
-
-#define FLASH_BASE_ADDR 0xf0000000
-#define FLASH_BANK_SIZE (128*1024*1024)
-
-MODULE_AUTHOR("Scott Wood, TimeSys Corporation <scott.wood@timesys.com>");
-MODULE_DESCRIPTION("User-programmable flash device on the Dy4 SVME182 board");
-MODULE_LICENSE("GPL");
-
-static struct map_info svme182_map = {
-	.name		= "Dy4 SVME182",
-	.bankwidth	= 32,
-	.size		=  128 * 1024 * 1024
-};
-
-#define BOOTIMAGE_PART_SIZE		((6*1024*1024)-RESERVED_PART_SIZE)
-
-// Allow 6MiB for the kernel
-#define NEW_BOOTIMAGE_PART_SIZE  (6 * 1024 * 1024)
-// Allow 1MiB for the bootloader
-#define NEW_BOOTLOADER_PART_SIZE (1024 * 1024)
-// Use the remaining 9MiB at the end of flash for the RFS
-#define NEW_RFS_PART_SIZE        (0x01000000 - NEW_BOOTLOADER_PART_SIZE - \
-                                  NEW_BOOTIMAGE_PART_SIZE)
-
-static struct mtd_partition svme182_partitions[] = {
-	// The Lower PABS is only 128KiB, but the partition code doesn't
-	// like partitions that don't end on the largest erase block
-	// size of the device, even if all of the erase blocks in the
-	// partition are small ones.  The hardware should prevent
-	// writes to the actual PABS areas.
-	{
-		name:       "Lower PABS and CPU 0 bootloader or kernel",
-		size:       6*1024*1024,
-		offset:     0,
-	},
-	{
-		name:       "Root Filesystem",
-		size:       10*1024*1024,
-		offset:     MTDPART_OFS_NXTBLK
-	},
-	{
-		name:       "CPU1 Bootloader",
-		size:       1024*1024,
-		offset:     MTDPART_OFS_NXTBLK,
-	},
-	{
-		name:       "Extra",
-		size:       110*1024*1024,
-		offset:     MTDPART_OFS_NXTBLK
-	},
-	{
-		name:       "Foundation Firmware and Upper PABS",
-		size:       1024*1024,
-		offset:     MTDPART_OFS_NXTBLK,
-		mask_flags: MTD_WRITEABLE // read-only
-	}
-};
-
-static struct mtd_info *this_mtd;
-
-static int __init init_svme182(void)
-{
-	struct mtd_partition *partitions;
-	int num_parts = ARRAY_SIZE(svme182_partitions);
-
-	partitions = svme182_partitions;
-
-	svme182_map.virt = ioremap(FLASH_BASE_ADDR, svme182_map.size);
-
-	if (svme182_map.virt == 0) {
-		printk("Failed to ioremap FLASH memory area.\n");
-		return -EIO;
-	}
-
-	simple_map_init(&svme182_map);
-
-	this_mtd = do_map_probe("cfi_probe", &svme182_map);
-	if (!this_mtd)
-	{
-		iounmap((void *)svme182_map.virt);
-		return -ENXIO;
-	}
-
-	printk(KERN_NOTICE "SVME182 flash device: %dMiB at 0x%08x\n",
-		   this_mtd->size >> 20, FLASH_BASE_ADDR);
-
-	this_mtd->owner = THIS_MODULE;
-	mtd_device_register(this_mtd, partitions, num_parts);
-
-	return 0;
-}
-
-static void __exit cleanup_svme182(void)
-{
-	if (this_mtd)
-	{
-		mtd_device_unregister(this_mtd);
-		map_destroy(this_mtd);
-	}
-
-	if (svme182_map.virt)
-	{
-		iounmap((void *)svme182_map.virt);
-		svme182_map.virt = 0;
-	}
-
-	return;
-}
-
-module_init(init_svme182);
-module_exit(cleanup_svme182);

drivers/mtd/maps/gpio-addr-flash.c

@@ -157,7 +157,8 @@ static void gf_copy_to(struct map_info *map, unsigned long to,
 	memcpy_toio(map->virt + (to % state->win_size), from, len);
 }
 
-static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", NULL };
+static const char * const part_probe_types[] = {
+	"cmdlinepart", "RedBoot", NULL };
 
 /**
  * gpio_flash_probe() - setup a mapping for a GPIO assisted flash

drivers/mtd/maps/h720x-flash.c

-/*
- * Flash memory access on Hynix GMS30C7201/HMS30C7202 based
- * evaluation boards
- *
- * (C) 2002 Jungjun Kim <jungjun.kim@hynix.com>
- *     2003 Thomas Gleixner <tglx@linutronix.de>
- */
-
-#include <linux/module.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/slab.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/map.h>
-#include <linux/mtd/partitions.h>
-#include <mach/hardware.h>
-#include <asm/io.h>
-
-static struct mtd_info *mymtd;
-
-static struct map_info h720x_map = {
-	.name =		"H720X",
-	.bankwidth =	4,
-	.size =		H720X_FLASH_SIZE,
-	.phys =		H720X_FLASH_PHYS,
-};
-
-static struct mtd_partition h720x_partitions[] = {
-        {
-                .name = "ArMon",
-                .size = 0x00080000,
-                .offset = 0,
-                .mask_flags = MTD_WRITEABLE
-        },{
-                .name = "Env",
-                .size = 0x00040000,
-                .offset = 0x00080000,
-                .mask_flags = MTD_WRITEABLE
-        },{
-                .name = "Kernel",
-                .size = 0x00180000,
-                .offset = 0x000c0000,
-                .mask_flags = MTD_WRITEABLE
-        },{
-                .name = "Ramdisk",
-                .size = 0x00400000,
-                .offset = 0x00240000,
-                .mask_flags = MTD_WRITEABLE
-        },{
-                .name = "jffs2",
-                .size = MTDPART_SIZ_FULL,
-                .offset = MTDPART_OFS_APPEND
-        }
-};
-
-#define NUM_PARTITIONS ARRAY_SIZE(h720x_partitions)
-
-/*
- * Initialize FLASH support
- */
-static int __init h720x_mtd_init(void)
-{
-	h720x_map.virt = ioremap(h720x_map.phys, h720x_map.size);
-
-	if (!h720x_map.virt) {
-		printk(KERN_ERR "H720x-MTD: ioremap failed\n");
-		return -EIO;
-	}
-
-	simple_map_init(&h720x_map);
-
-	// Probe for flash bankwidth 4
-	printk (KERN_INFO "H720x-MTD probing 32bit FLASH\n");
-	mymtd = do_map_probe("cfi_probe", &h720x_map);
-	if (!mymtd) {
-		printk (KERN_INFO "H720x-MTD probing 16bit FLASH\n");
-	    // Probe for bankwidth 2
-	    h720x_map.bankwidth = 2;
-	    mymtd = do_map_probe("cfi_probe", &h720x_map);
-	}
-
-	if (mymtd) {
-		mymtd->owner = THIS_MODULE;
-
-		mtd_device_parse_register(mymtd, NULL, NULL,
-					  h720x_partitions, NUM_PARTITIONS);
-		return 0;
-	}
-
-	iounmap((void *)h720x_map.virt);
-	return -ENXIO;
-}
-
-/*
- * Cleanup
- */
-static void __exit h720x_mtd_cleanup(void)
-{
-
-	if (mymtd) {
-		mtd_device_unregister(mymtd);
-		map_destroy(mymtd);
-	}
-
-	if (h720x_map.virt) {
-		iounmap((void *)h720x_map.virt);
-		h720x_map.virt = 0;
-	}
-}
-
-
-module_init(h720x_mtd_init);
-module_exit(h720x_mtd_cleanup);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Thomas Gleixner <tglx@linutronix.de>");
-MODULE_DESCRIPTION("MTD map driver for Hynix evaluation boards");

drivers/mtd/maps/impa7.c

@@ -24,14 +24,12 @@
 #define NUM_FLASHBANKS 2
 #define BUSWIDTH     4
 
-/* can be { "cfi_probe", "jedec_probe", "map_rom", NULL } */
-#define PROBETYPES { "jedec_probe", NULL }
-
 #define MSG_PREFIX "impA7:"   /* prefix for our printk()'s */
 #define MTDID      "impa7-%d"  /* for mtdparts= partitioning */
 
 static struct mtd_info *impa7_mtd[NUM_FLASHBANKS];
 
+static const char * const rom_probe_types[] = { "jedec_probe", NULL };
 
 static struct map_info impa7_map[NUM_FLASHBANKS] = {
 	{
@@ -60,8 +58,7 @@ static struct mtd_partition partitions[] =
 
 static int __init init_impa7(void)
 {
-	static const char *rom_probe_types[] = PROBETYPES;
-	const char **type;
+	const char * const *type;
 	int i;
 	static struct { u_long addr; u_long size; } pt[NUM_FLASHBANKS] = {
 	  { WINDOW_ADDR0, WINDOW_SIZE0 },

drivers/mtd/maps/intel_vr_nor.c

@@ -82,9 +82,9 @@ static void vr_nor_destroy_mtd_setup(struct vr_nor_mtd *p)
 
 static int vr_nor_mtd_setup(struct vr_nor_mtd *p)
 {
-	static const char *probe_types[] =
+	static const char * const probe_types[] =
 	    { "cfi_probe", "jedec_probe", NULL };
-	const char **type;
+	const char * const *type;
 
 	for (type = probe_types; !p->info && *type; type++)
 		p->info = do_map_probe(*type, &p->map);

drivers/mtd/maps/ixp4xx.c

@@ -148,7 +148,7 @@ struct ixp4xx_flash_info {
 	struct resource *res;
 };
 
-static const char *probes[] = { "RedBoot", "cmdlinepart", NULL };
+static const char * const probes[] = { "RedBoot", "cmdlinepart", NULL };
 
 static int ixp4xx_flash_remove(struct platform_device *dev)
 {

drivers/mtd/maps/lantiq-flash.c

@@ -46,8 +46,7 @@ struct ltq_mtd {
 };
 
 static const char ltq_map_name[] = "ltq_nor";
-static const char *ltq_probe_types[] = {
-					"cmdlinepart", "ofpart", NULL };
+static const char * const ltq_probe_types[] = { "cmdlinepart", "ofpart", NULL };
 
 static map_word
 ltq_read16(struct map_info *map, unsigned long adr)