Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
  ARM: 5728/1: Proper prefetch abort handling on ARMv6 and ARMv7
  ARM: 5727/1: Pass IFSR register to do_PrefetchAbort()
  ARM: 5740/1: fix valid_phys_addr_range() range check
  ARM: 5739/1: ARM: allow empty ATAG_CORE
  ARM: 5735/1: sa1111: CodingStyle cleanups
  ARM: 5738/1: Correct TCM documentation
  ARM: 5734/1: arm: fix compilation of entry-common.S for older CPUs
  ARM: 5733/1: fix bcmring compile error
  ARM: 5732/1: remove redundant include file
  ARM: 5731/2: Fix U300 generic GPIO, remove ifdefs from MMCI v3
  ARM: Ensure do_cache_op takes mmap_sem
  ARM: Fix __cpuexit section mismatch warnings
  ARM: Don't allow highmem on SMP platforms without h/w TLB ops broadcast
  ARM: includecheck fix: mach-davinci, board-dm365-evm.c
  ARM: Remove unused CONFIG SA1100_H3XXX
  ARM: Fix warning: unused variable 'highmem'
  ARM: Fix warning: #warning syscall migrate_pages not implemented
  ARM: Fix SA11x0 clocksource warning
  ARM: Fix SA1100 Neponset serial section mismatch
  ARM: Fix SA1100 Assabet/Neponset PCMCIA section mismatch warnings
  ...

Documentation/arm/tcm.txt

@@ -29,11 +29,13 @@ TCM location and size. Notice that this is not a MMU table: you
 actually move the physical location of the TCM around. At the
 place you put it, it will mask any underlying RAM from the
 CPU so it is usually wise not to overlap any physical RAM with
-the TCM. The TCM memory exists totally outside the MMU and will
-override any MMU mappings.
+the TCM.
 
-Code executing inside the ITCM does not "see" any MMU mappings
-and e.g. register accesses must be made to physical addresses.
+The TCM memory can then be remapped to another address again using
+the MMU, but notice that the TCM if often used in situations where
+the MMU is turned off. To avoid confusion the current Linux
+implementation will map the TCM 1 to 1 from physical to virtual
+memory in the location specified by the machine.
 
 TCM is used for a few things:
 

MAINTAINERS

@@ -646,24 +646,24 @@ ARM/INTEL IOP32X ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IOP33X ARM ARCHITECTURE
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IOP13XX ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IQ81342EX MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/INTEL IXP2000 ARM ARCHITECTURE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -691,7 +691,7 @@ ARM/INTEL XSC3 (MANZANO) ARM CORE
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 M:	Dan Williams <dan.j.williams@intel.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Maintained
 
 ARM/IP FABRICS DOUBLE ESPRESSO MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
@@ -2695,7 +2695,7 @@ F:	include/linux/intel-iommu.h
 
 INTEL IOP-ADMA DMA DRIVER
 M:	Dan Williams <dan.j.williams@intel.com>
-S:	Supported
+S:	Maintained
 F:	drivers/dma/iop-adma.c
 
 INTEL IXP4XX QMGR, NPE, ETHERNET and HSS SUPPORT

arch/arm/common/sa1111.c

@@ -1032,6 +1032,7 @@ unsigned int sa1111_pll_clock(struct sa1111_dev *sadev)
 
 	return __sa1111_pll_clock(sachip);
 }
+EXPORT_SYMBOL(sa1111_pll_clock);
 
 /**
  *	sa1111_select_audio_mode - select I2S or AC link mode
@@ -1059,6 +1060,7 @@ void sa1111_select_audio_mode(struct sa1111_dev *sadev, int mode)
 
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_select_audio_mode);
 
 /**
  *	sa1111_set_audio_rate - set the audio sample rate
@@ -1083,6 +1085,7 @@ int sa1111_set_audio_rate(struct sa1111_dev *sadev, int rate)
 
 	return 0;
 }
+EXPORT_SYMBOL(sa1111_set_audio_rate);
 
 /**
  *	sa1111_get_audio_rate - get the audio sample rate
@@ -1100,6 +1103,7 @@ int sa1111_get_audio_rate(struct sa1111_dev *sadev)
 
 	return __sa1111_pll_clock(sachip) / (256 * div);
 }
+EXPORT_SYMBOL(sa1111_get_audio_rate);
 
 void sa1111_set_io_dir(struct sa1111_dev *sadev,
 		       unsigned int bits, unsigned int dir,
@@ -1128,6 +1132,7 @@ void sa1111_set_io_dir(struct sa1111_dev *sadev,
 	MODIFY_BITS(gpio + SA1111_GPIO_PCSDR, (bits >> 16) & 255, sleep_dir >> 16);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_set_io_dir);
 
 void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
 {
@@ -1142,6 +1147,7 @@ void sa1111_set_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
 	MODIFY_BITS(gpio + SA1111_GPIO_PCDWR, (bits >> 16) & 255, v >> 16);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_set_io);
 
 void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned int v)
 {
@@ -1156,6 +1162,7 @@ void sa1111_set_sleep_io(struct sa1111_dev *sadev, unsigned int bits, unsigned i
 	MODIFY_BITS(gpio + SA1111_GPIO_PCSSR, (bits >> 16) & 255, v >> 16);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_set_sleep_io);
 
 /*
  * Individual device operations.
@@ -1176,6 +1183,7 @@ void sa1111_enable_device(struct sa1111_dev *sadev)
 	sa1111_writel(val | sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_enable_device);
 
 /**
  *	sa1111_disable_device - disable an on-chip SA1111 function block
@@ -1192,6 +1200,7 @@ void sa1111_disable_device(struct sa1111_dev *sadev)
 	sa1111_writel(val & ~sadev->skpcr_mask, sachip->base + SA1111_SKPCR);
 	spin_unlock_irqrestore(&sachip->lock, flags);
 }
+EXPORT_SYMBOL(sa1111_disable_device);
 
 /*
  *	SA1111 "Register Access Bus."
@@ -1259,17 +1268,20 @@ struct bus_type sa1111_bus_type = {
 	.suspend	= sa1111_bus_suspend,
 	.resume		= sa1111_bus_resume,
 };
+EXPORT_SYMBOL(sa1111_bus_type);
 
 int sa1111_driver_register(struct sa1111_driver *driver)
 {
 	driver->drv.bus = &sa1111_bus_type;
 	return driver_register(&driver->drv);
 }
+EXPORT_SYMBOL(sa1111_driver_register);
 
 void sa1111_driver_unregister(struct sa1111_driver *driver)
 {
 	driver_unregister(&driver->drv);
 }
+EXPORT_SYMBOL(sa1111_driver_unregister);
 
 static int __init sa1111_init(void)
 {
@@ -1290,16 +1302,3 @@ module_exit(sa1111_exit);
 
 MODULE_DESCRIPTION("Intel Corporation SA1111 core driver");
 MODULE_LICENSE("GPL");
-
-EXPORT_SYMBOL(sa1111_select_audio_mode);
-EXPORT_SYMBOL(sa1111_set_audio_rate);
-EXPORT_SYMBOL(sa1111_get_audio_rate);
-EXPORT_SYMBOL(sa1111_set_io_dir);
-EXPORT_SYMBOL(sa1111_set_io);
-EXPORT_SYMBOL(sa1111_set_sleep_io);
-EXPORT_SYMBOL(sa1111_enable_device);
-EXPORT_SYMBOL(sa1111_disable_device);
-EXPORT_SYMBOL(sa1111_pll_clock);
-EXPORT_SYMBOL(sa1111_bus_type);
-EXPORT_SYMBOL(sa1111_driver_register);
-EXPORT_SYMBOL(sa1111_driver_unregister);

arch/arm/configs/h3600_defconfig

@@ -90,7 +90,6 @@ CONFIG_ARCH_SA1100=y
 # CONFIG_SA1100_COLLIE is not set
 # CONFIG_SA1100_H3100 is not set
 CONFIG_SA1100_H3600=y
-CONFIG_SA1100_H3XXX=y
 # CONFIG_SA1100_BADGE4 is not set
 # CONFIG_SA1100_JORNADA720 is not set
 # CONFIG_SA1100_HACKKIT is not set

arch/arm/include/asm/glue.h

@@ -120,25 +120,39 @@
 #endif
 
 /*
- * Prefetch abort handler.  If the CPU has an IFAR use that, otherwise
- * use the address of the aborted instruction
+ *	Prefetch Abort Model
+ *	================
+ *
+ *	We have the following to choose from:
+ *	  legacy	- no IFSR, no IFAR
+ *	  v6		- ARMv6: IFSR, no IFAR
+ *	  v7		- ARMv7: IFSR and IFAR
  */
+
 #undef CPU_PABORT_HANDLER
 #undef MULTI_PABORT
 
-#ifdef CONFIG_CPU_PABRT_IFAR
+#ifdef CONFIG_CPU_PABRT_LEGACY
+# ifdef CPU_PABORT_HANDLER
+#  define MULTI_PABORT 1
+# else
+#  define CPU_PABORT_HANDLER legacy_pabort
+# endif
+#endif
+
+#ifdef CONFIG_CPU_PABRT_V6
 # ifdef CPU_PABORT_HANDLER
 #  define MULTI_PABORT 1
 # else
-#  define CPU_PABORT_HANDLER(reg, insn)	mrc p15, 0, reg, cr6, cr0, 2
+#  define CPU_PABORT_HANDLER v6_pabort
 # endif
 #endif
 
-#ifdef CONFIG_CPU_PABRT_NOIFAR
+#ifdef CONFIG_CPU_PABRT_V7
 # ifdef CPU_PABORT_HANDLER
 #  define MULTI_PABORT 1
 # else
-#  define CPU_PABORT_HANDLER(reg, insn)	mov reg, insn
+#  define CPU_PABORT_HANDLER v7_pabort
 # endif
 #endif
 

arch/arm/include/asm/hardware/iop3xx.h

@@ -215,6 +215,7 @@ extern int iop3xx_get_init_atu(void);
  * IOP3XX I/O and Mem space regions for PCI autoconfiguration
  */
 #define IOP3XX_PCI_LOWER_MEM_PA	0x80000000
+#define IOP3XX_PCI_MEM_WINDOW_SIZE	0x08000000
 
 #define IOP3XX_PCI_IO_WINDOW_SIZE	0x00010000
 #define IOP3XX_PCI_LOWER_IO_PA		0x90000000

arch/arm/include/asm/smp_plat.h

+/*
+ * ARM specific SMP header, this contains our implementation
+ * details.
+ */
+#ifndef __ASMARM_SMP_PLAT_H
+#define __ASMARM_SMP_PLAT_H
+
+#include <asm/cputype.h>
+
+/* all SMP configurations have the extended CPUID registers */
+static inline int tlb_ops_need_broadcast(void)
+{
+	return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
+}
+
+#endif

arch/arm/include/asm/unistd.h

@@ -456,6 +456,7 @@
  * Unimplemented (or alternatively implemented) syscalls
  */
 #define __IGNORE_fadvise64_64		1
+#define __IGNORE_migrate_pages		1
 
 #endif /* __KERNEL__ */
 #endif /* __ASM_ARM_UNISTD_H */

arch/arm/kernel/entry-armv.S

@@ -311,22 +311,16 @@ __pabt_svc:
 	tst	r3, #PSR_I_BIT
 	biceq	r9, r9, #PSR_I_BIT
 
-	@
-	@ set args, then call main handler
-	@
-	@  r0 - address of faulting instruction
-	@  r1 - pointer to registers on stack
-	@
-#ifdef MULTI_PABORT
 	mov	r0, r2			@ pass address of aborted instruction.
+#ifdef MULTI_PABORT
 	ldr	r4, .LCprocfns
 	mov	lr, pc
 	ldr	pc, [r4, #PROCESSOR_PABT_FUNC]
 #else
-	CPU_PABORT_HANDLER(r0, r2)
+	bl	CPU_PABORT_HANDLER
 #endif
 	msr	cpsr_c, r9			@ Maybe enable interrupts
-	mov	r1, sp				@ regs
+	mov	r2, sp				@ regs
 	bl	do_PrefetchAbort		@ call abort handler
 
 	@
@@ -701,16 +695,16 @@ ENDPROC(__und_usr_unknown)
 __pabt_usr:
 	usr_entry
 
-#ifdef MULTI_PABORT
 	mov	r0, r2			@ pass address of aborted instruction.
+#ifdef MULTI_PABORT
 	ldr	r4, .LCprocfns
 	mov	lr, pc
 	ldr	pc, [r4, #PROCESSOR_PABT_FUNC]
 #else
-	CPU_PABORT_HANDLER(r0, r2)
+	bl	CPU_PABORT_HANDLER
 #endif
 	enable_irq				@ Enable interrupts
-	mov	r1, sp				@ regs
+	mov	r2, sp				@ regs
 	bl	do_PrefetchAbort		@ call abort handler
  UNWIND(.fnend		)
 	/* fall through */

arch/arm/kernel/entry-common.S

@@ -126,7 +126,7 @@ ENTRY(__gnu_mcount_nc)
 	cmp r0, r2
 	bne gnu_trace
 	ldmia sp!, {r0-r3, ip, lr}
-	bx ip
+	mov pc, ip
 
 gnu_trace:
 	ldr r1, [sp, #20]			@ lr of instrumented routine
@@ -135,7 +135,7 @@ gnu_trace:
 	mov lr, pc
 	mov pc, r2
 	ldmia sp!, {r0-r3, ip, lr}
-	bx ip
+	mov pc, ip
 
 ENTRY(mcount)
 	stmdb sp!, {r0-r3, lr}
@@ -425,13 +425,6 @@ sys_mmap2:
 #endif
 ENDPROC(sys_mmap2)
 
-ENTRY(pabort_ifar)
-		mrc	p15, 0, r0, cr6, cr0, 2
-ENTRY(pabort_noifar)
-		mov	pc, lr
-ENDPROC(pabort_ifar)
-ENDPROC(pabort_noifar)
-
 #ifdef CONFIG_OABI_COMPAT
 
 /*

arch/arm/kernel/head-common.S

@@ -13,6 +13,7 @@
 
 #define ATAG_CORE 0x54410001
 #define ATAG_CORE_SIZE ((2*4 + 3*4) >> 2)
+#define ATAG_CORE_SIZE_EMPTY ((2*4) >> 2)
 
 	.align	2
 	.type	__switch_data, %object
@@ -251,7 +252,8 @@ __vet_atags:
 	bne	1f
 
 	ldr	r5, [r2, #0]			@ is first tag ATAG_CORE?
-	subs	r5, r5, #ATAG_CORE_SIZE
+	cmp	r5, #ATAG_CORE_SIZE
+	cmpne	r5, #ATAG_CORE_SIZE_EMPTY
 	bne	1f
 	ldr	r5, [r2, #4]
 	ldr	r6, =ATAG_CORE

arch/arm/kernel/smp.c

@@ -36,6 +36,7 @@
 #include <asm/tlbflush.h>
 #include <asm/ptrace.h>
 #include <asm/localtimer.h>
+#include <asm/smp_plat.h>
 
 /*
  * as from 2.5, kernels no longer have an init_tasks structure
@@ -153,7 +154,7 @@ int __cpuinit __cpu_up(unsigned int cpu)
 /*
  * __cpu_disable runs on the processor to be shutdown.
  */
-int __cpuexit __cpu_disable(void)
+int __cpu_disable(void)
 {
 	unsigned int cpu = smp_processor_id();
 	struct task_struct *p;
@@ -200,7 +201,7 @@ int __cpuexit __cpu_disable(void)
  * called on the thread which is asking for a CPU to be shutdown -
  * waits until shutdown has completed, or it is timed out.
  */
-void __cpuexit __cpu_die(unsigned int cpu)
+void __cpu_die(unsigned int cpu)
 {
 	if (!platform_cpu_kill(cpu))
 		printk("CPU%u: unable to kill\n", cpu);
@@ -214,7 +215,7 @@ void __cpuexit __cpu_die(unsigned int cpu)
  * of the other hotplug-cpu capable cores, so presumably coming
  * out of idle fixes this.
  */
-void __cpuexit cpu_die(void)
+void __ref cpu_die(void)
 {
 	unsigned int cpu = smp_processor_id();
 
@@ -586,12 +587,6 @@ struct tlb_args {
 	unsigned long ta_end;
 };
 
-/* all SMP configurations have the extended CPUID registers */
-static inline int tlb_ops_need_broadcast(void)
-{
-	return ((read_cpuid_ext(CPUID_EXT_MMFR3) >> 12) & 0xf) < 2;
-}
-
 static inline void ipi_flush_tlb_all(void *ignored)
 {
 	local_flush_tlb_all();

arch/arm/kernel/smp_twd.c

@@ -166,10 +166,12 @@ void __cpuinit twd_timer_setup(struct clock_event_device *clk)
 	clockevents_register_device(clk);
 }
 
+#ifdef CONFIG_HOTPLUG_CPU
 /*
  * take a local timer down
  */
-void __cpuexit twd_timer_stop(void)
+void twd_timer_stop(void)
 {
 	__raw_writel(0, twd_base + TWD_TIMER_CONTROL);
 }
+#endif

arch/arm/kernel/traps.c

@@ -418,12 +418,14 @@ static int bad_syscall(int n, struct pt_regs *regs)
 static inline void
 do_cache_op(unsigned long start, unsigned long end, int flags)
 {
+	struct mm_struct *mm = current->active_mm;
 	struct vm_area_struct *vma;
 
 	if (end < start || flags)
 		return;
 
-	vma = find_vma(current->active_mm, start);
+	down_read(&mm->mmap_sem);
+	vma = find_vma(mm, start);
 	if (vma && vma->vm_start < end) {
 		if (start < vma->vm_start)
 			start = vma->vm_start;
@@ -432,6 +434,7 @@ do_cache_op(unsigned long start, unsigned long end, int flags)
 
 		flush_cache_user_range(vma, start, end);
 	}
+	up_read(&mm->mmap_sem);
 }
 
 /*

arch/arm/mach-bcmring/core.c

@@ -31,7 +31,6 @@
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
 
-#include <linux/amba/bus.h>
 #include <mach/csp/mm_addr.h>
 #include <mach/hardware.h>
 #include <asm/clkdev.h>
@@ -45,7 +44,6 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 #include <asm/mach/map.h>
-#include <asm/mach/mmc.h>
 
 #include <cfg_global.h>
 

arch/arm/mach-davinci/board-dm365-evm.c

@@ -35,7 +35,6 @@
 #include <mach/common.h>
 #include <mach/i2c.h>
 #include <mach/serial.h>
-#include <mach/common.h>
 #include <mach/mmc.h>
 #include <mach/nand.h>
 

arch/arm/mach-integrator/pci_v3.c

@@ -486,7 +486,7 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys)
 	return ret;
 }
 
-struct pci_bus *pci_v3_scan_bus(int nr, struct pci_sys_data *sys)
+struct pci_bus * __init pci_v3_scan_bus(int nr, struct pci_sys_data *sys)
 {
 	return pci_scan_bus(sys->busnr, &pci_v3_ops, sys);
 }

arch/arm/mach-iop32x/include/mach/iop32x.h

@@ -31,7 +31,5 @@
 #define IOP32X_MAX_RAM_SIZE            0x40000000UL
 #define IOP3XX_MAX_RAM_SIZE            IOP32X_MAX_RAM_SIZE
 #define IOP3XX_PCI_LOWER_MEM_BA        0x80000000
-#define IOP32X_PCI_MEM_WINDOW_SIZE     0x04000000
-#define IOP3XX_PCI_MEM_WINDOW_SIZE     IOP32X_PCI_MEM_WINDOW_SIZE
 
 #endif

arch/arm/mach-iop33x/include/mach/iop33x.h

@@ -36,8 +36,6 @@
 #define IOP33X_MAX_RAM_SIZE		0x80000000UL
 #define IOP3XX_MAX_RAM_SIZE		IOP33X_MAX_RAM_SIZE
 #define IOP3XX_PCI_LOWER_MEM_BA	(PHYS_OFFSET + IOP33X_MAX_RAM_SIZE)
-#define IOP33X_PCI_MEM_WINDOW_SIZE	0x08000000
-#define IOP3XX_PCI_MEM_WINDOW_SIZE	IOP33X_PCI_MEM_WINDOW_SIZE
 
 
 #endif

arch/arm/mach-sa1100/Kconfig

@@ -71,11 +71,6 @@ config SA1100_H3600
 	  <http://www.handhelds.org/Compaq/index.html#iPAQ_H3600>
 	  <http://www.compaq.com/products/handhelds/pocketpc/>
 
-config SA1100_H3XXX
-	bool
-	depends on SA1100_H3100 || SA1100_H3600
-	default y
-
 config SA1100_BADGE4
 	bool "HP Labs BadgePAD 4"
 	select SA1111

arch/arm/mach-sa1100/time.c

@@ -77,7 +77,7 @@ static struct clock_event_device ckevt_sa1100_osmr0 = {
 	.set_mode	= sa1100_osmr0_set_mode,
 };
 
-static cycle_t sa1100_read_oscr(void)
+static cycle_t sa1100_read_oscr(struct clocksource *s)
 {
 	return OSCR;
 }

arch/arm/mach-u300/gpio.c

@@ -281,6 +281,16 @@ int gpio_unregister_callback(unsigned gpio)
 }
 EXPORT_SYMBOL(gpio_unregister_callback);
 
+/* Non-zero means valid */
+int gpio_is_valid(int number)
+{
+	if (number >= 0 &&
+	    number < (U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT))
+		return 1;
+	return 0;
+}
+EXPORT_SYMBOL(gpio_is_valid);
+
 int gpio_request(unsigned gpio, const char *label)
 {
 	if (gpio_pin[gpio].users)

arch/arm/mach-u300/include/mach/gpio.h

@@ -258,6 +258,7 @@
 #define PIN_TO_PORT(val) (val >> 3)
 
 /* These can be found in arch/arm/mach-u300/gpio.c */
+extern int gpio_is_valid(int number);
 extern int gpio_request(unsigned gpio, const char *label);
 extern void gpio_free(unsigned gpio);
 extern int gpio_direction_input(unsigned gpio);

arch/arm/mm/Kconfig

@@ -17,7 +17,7 @@ config CPU_ARM610
 	select CPU_CP15_MMU
 	select CPU_COPY_V3 if MMU
 	select CPU_TLB_V3 if MMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	help
 	  The ARM610 is the successor to the ARM3 processor
 	  and was produced by VLSI Technology Inc.
@@ -31,7 +31,7 @@ config CPU_ARM7TDMI
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_LV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4
 	help
 	  A 32-bit RISC microprocessor based on the ARM7 processor core
@@ -49,7 +49,7 @@ config CPU_ARM710
 	select CPU_CP15_MMU
 	select CPU_COPY_V3 if MMU
 	select CPU_TLB_V3 if MMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	help
 	  A 32-bit RISC microprocessor based on the ARM7 processor core
 	  designed by Advanced RISC Machines Ltd. The ARM710 is the
@@ -64,7 +64,7 @@ config CPU_ARM720T
 	bool "Support ARM720T processor" if ARCH_INTEGRATOR
 	select CPU_32v4T
 	select CPU_ABRT_LV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -83,7 +83,7 @@ config CPU_ARM740T
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_LV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V3	# although the core is v4t
 	select CPU_CP15_MPU
 	help
@@ -100,7 +100,7 @@ config CPU_ARM9TDMI
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_NOMMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4
 	help
 	  A 32-bit RISC microprocessor based on the ARM9 processor core
@@ -114,7 +114,7 @@ config CPU_ARM920T
 	bool "Support ARM920T processor" if ARCH_INTEGRATOR
 	select CPU_32v4T
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -135,7 +135,7 @@ config CPU_ARM922T
 	bool "Support ARM922T processor" if ARCH_INTEGRATOR
 	select CPU_32v4T
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -154,7 +154,7 @@ config CPU_ARM925T
  	bool "Support ARM925T processor" if ARCH_OMAP1
 	select CPU_32v4T
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -173,7 +173,7 @@ config CPU_ARM926T
 	bool "Support ARM926T processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB
 	select CPU_32v5
 	select CPU_ABRT_EV5TJ
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_V4WB if MMU
@@ -191,7 +191,7 @@ config CPU_FA526
 	bool
 	select CPU_32v4
 	select CPU_ABRT_EV4
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_CACHE_FA
@@ -210,7 +210,7 @@ config CPU_ARM940T
 	depends on !MMU
 	select CPU_32v4T
 	select CPU_ABRT_NOMMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MPU
 	help
@@ -228,7 +228,7 @@ config CPU_ARM946E
 	depends on !MMU
 	select CPU_32v5
 	select CPU_ABRT_NOMMU
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MPU
 	help
@@ -244,7 +244,7 @@ config CPU_ARM1020
 	bool "Support ARM1020T (rev 0) processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -262,7 +262,7 @@ config CPU_ARM1020E
 	bool "Support ARM1020E processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WT
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -275,7 +275,7 @@ config CPU_ARM1022
 	bool "Support ARM1022E processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV4T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_V4WB if MMU # can probably do better
@@ -293,7 +293,7 @@ config CPU_ARM1026
 	bool "Support ARM1026EJ-S processor" if ARCH_INTEGRATOR
 	select CPU_32v5
 	select CPU_ABRT_EV5T # But need Jazelle, but EV5TJ ignores bit 10
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_V4WB if MMU # can probably do better
@@ -311,7 +311,7 @@ config CPU_SA110
 	select CPU_32v3 if ARCH_RPC
 	select CPU_32v4 if !ARCH_RPC
 	select CPU_ABRT_EV4
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WB
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -331,7 +331,7 @@ config CPU_SA1100
 	bool
 	select CPU_32v4
 	select CPU_ABRT_EV4
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_V4WB
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
@@ -342,7 +342,7 @@ config CPU_XSCALE
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_TLB_V4WBI if MMU
@@ -352,7 +352,7 @@ config CPU_XSC3
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_TLB_V4WBI if MMU
@@ -363,7 +363,7 @@ config CPU_MOHAWK
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_TLB_V4WBI if MMU
@@ -374,7 +374,7 @@ config CPU_FEROCEON
 	bool
 	select CPU_32v5
 	select CPU_ABRT_EV5T
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_LEGACY
 	select CPU_CACHE_VIVT
 	select CPU_CP15_MMU
 	select CPU_COPY_FEROCEON if MMU
@@ -394,7 +394,7 @@ config CPU_V6
 	bool "Support ARM V6 processor" if ARCH_INTEGRATOR || MACH_REALVIEW_EB || MACH_REALVIEW_PBX
 	select CPU_32v6
 	select CPU_ABRT_EV6
-	select CPU_PABRT_NOIFAR
+	select CPU_PABRT_V6
 	select CPU_CACHE_V6
 	select CPU_CACHE_VIPT
 	select CPU_CP15_MMU
@@ -420,7 +420,7 @@ config CPU_V7
 	select CPU_32v6K
 	select CPU_32v7
 	select CPU_ABRT_EV7
-	select CPU_PABRT_IFAR
+	select CPU_PABRT_V7
 	select CPU_CACHE_V7
 	select CPU_CACHE_VIPT
 	select CPU_CP15_MMU
@@ -482,10 +482,13 @@ config CPU_ABRT_EV6
 config CPU_ABRT_EV7
 	bool
 
-config CPU_PABRT_IFAR
+config CPU_PABRT_LEGACY
 	bool
 
-config CPU_PABRT_NOIFAR
+config CPU_PABRT_V6
+	bool
+
+config CPU_PABRT_V7
 	bool
 
 # The cache model

arch/arm/mm/Makefile

@@ -27,6 +27,10 @@ obj-$(CONFIG_CPU_ABRT_EV5TJ)	+= abort-ev5tj.o
 obj-$(CONFIG_CPU_ABRT_EV6)	+= abort-ev6.o
 obj-$(CONFIG_CPU_ABRT_EV7)	+= abort-ev7.o
 
+obj-$(CONFIG_CPU_PABRT_LEGACY)	+= pabort-legacy.o
+obj-$(CONFIG_CPU_PABRT_V6)	+= pabort-v6.o
+obj-$(CONFIG_CPU_PABRT_V7)	+= pabort-v7.o
+
 obj-$(CONFIG_CPU_CACHE_V3)	+= cache-v3.o
 obj-$(CONFIG_CPU_CACHE_V4)	+= cache-v4.o
 obj-$(CONFIG_CPU_CACHE_V4WT)	+= cache-v4wt.o

arch/arm/mm/fault.c

@@ -519,9 +519,58 @@ do_DataAbort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	arm_notify_die("", regs, &info, fsr, 0);
 }
 
+
+static struct fsr_info ifsr_info[] = {
+	{ do_bad,		SIGBUS,  0,		"unknown 0"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 1"			   },
+	{ do_bad,		SIGBUS,  0,		"debug event"			   },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"section access flag fault"	   },
+	{ do_bad,		SIGBUS,  0,		"unknown 4"			   },
+	{ do_translation_fault,	SIGSEGV, SEGV_MAPERR,	"section translation fault"	   },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"page access flag fault"	   },
+	{ do_page_fault,	SIGSEGV, SEGV_MAPERR,	"page translation fault"	   },
+	{ do_bad,		SIGBUS,	 0,		"external abort on non-linefetch"  },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"section domain fault"		   },
+	{ do_bad,		SIGBUS,  0,		"unknown 10"			   },
+	{ do_bad,		SIGSEGV, SEGV_ACCERR,	"page domain fault"		   },
+	{ do_bad,		SIGBUS,	 0,		"external abort on translation"	   },
+	{ do_sect_fault,	SIGSEGV, SEGV_ACCERR,	"section permission fault"	   },
+	{ do_bad,		SIGBUS,	 0,		"external abort on translation"	   },
+	{ do_page_fault,	SIGSEGV, SEGV_ACCERR,	"page permission fault"		   },
+	{ do_bad,		SIGBUS,  0,		"unknown 16"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 17"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 18"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 19"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 20"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 21"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 22"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 23"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 24"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 25"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 26"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 27"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 28"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 29"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 30"			   },
+	{ do_bad,		SIGBUS,  0,		"unknown 31"			   },
+};
+
 asmlinkage void __exception
-do_PrefetchAbort(unsigned long addr, struct pt_regs *regs)
+do_PrefetchAbort(unsigned long addr, unsigned int ifsr, struct pt_regs *regs)
 {
-	do_translation_fault(addr, FSR_LNX_PF, regs);
+	const struct fsr_info *inf = ifsr_info + fsr_fs(ifsr);
+	struct siginfo info;
+
+	if (!inf->fn(addr, ifsr | FSR_LNX_PF, regs))
+		return;
+
+	printk(KERN_ALERT "Unhandled prefetch abort: %s (0x%03x) at 0x%08lx\n",
+		inf->name, ifsr, addr);
+
+	info.si_signo = inf->sig;
+	info.si_errno = 0;
+	info.si_code  = inf->code;
+	info.si_addr  = (void __user *)addr;
+	arm_notify_die("", regs, &info, ifsr, 0);
 }
 

arch/arm/mm/mmap.c

@@ -124,7 +124,7 @@ int valid_phys_addr_range(unsigned long addr, size_t size)
 {
 	if (addr < PHYS_OFFSET)
 		return 0;
-	if (addr + size >= __pa(high_memory - 1))
+	if (addr + size > __pa(high_memory - 1) + 1)
 		return 0;
 
 	return 1;

arch/arm/mm/mmu.c

@@ -21,6 +21,7 @@
 #include <asm/cachetype.h>
 #include <asm/setup.h>
 #include <asm/sizes.h>
+#include <asm/smp_plat.h>
 #include <asm/tlb.h>
 #include <asm/highmem.h>
 
@@ -709,10 +710,6 @@ static void __init sanity_check_meminfo(void)
 			if (meminfo.nr_banks >= NR_BANKS) {
 				printk(KERN_CRIT "NR_BANKS too low, "
 						 "ignoring high memory\n");
-			} else if (cache_is_vipt_aliasing()) {
-				printk(KERN_CRIT "HIGHMEM is not yet supported "
-						 "with VIPT aliasing cache, "
-						 "ignoring high memory\n");
 			} else {
 				memmove(bank + 1, bank,
 					(meminfo.nr_banks - i) * sizeof(*bank));
@@ -726,6 +723,8 @@ static void __init sanity_check_meminfo(void)
 			bank->size = VMALLOC_MIN - __va(bank->start);
 		}
 #else
+		bank->highmem = highmem;
+
 		/*
 		 * Check whether this memory bank would entirely overlap
 		 * the vmalloc area.
@@ -754,6 +753,38 @@ static void __init sanity_check_meminfo(void)
 #endif
 		j++;
 	}
+#ifdef CONFIG_HIGHMEM
+	if (highmem) {
+		const char *reason = NULL;
+
+		if (cache_is_vipt_aliasing()) {
+			/*
+			 * Interactions between kmap and other mappings
+			 * make highmem support with aliasing VIPT caches
+			 * rather difficult.
+			 */
+			reason = "with VIPT aliasing cache";
+#ifdef CONFIG_SMP
+		} else if (tlb_ops_need_broadcast()) {
+			/*
+			 * kmap_high needs to occasionally flush TLB entries,
+			 * however, if the TLB entries need to be broadcast
+			 * we may deadlock:
+			 *  kmap_high(irqs off)->flush_all_zero_pkmaps->
+			 *  flush_tlb_kernel_range->smp_call_function_many
+			 *   (must not be called with irqs off)
+			 */
+			reason = "without hardware TLB ops broadcasting";
+#endif
+		}
+		if (reason) {
+			printk(KERN_CRIT "HIGHMEM is not supported %s, ignoring high memory\n",
+				reason);
+			while (j > 0 && meminfo.bank[j - 1].highmem)
+				j--;
+		}
+	}
+#endif
 	meminfo.nr_banks = j;
 }
 

arch/arm/mm/pabort-legacy.S

+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: legacy_pabort
+ *
+ * Params  : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ *	   : r1 = Simulated IFSR with section translation fault status
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+	.align	5
+ENTRY(legacy_pabort)
+	mov	r1, #5
+	mov	pc, lr
+ENDPROC(legacy_pabort)

arch/arm/mm/pabort-v6.S

+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: v6_pabort
+ *
+ * Params  : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ *	   : r1 = IFSR
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+	.align	5
+ENTRY(v6_pabort)
+	mrc	p15, 0, r1, c5, c0, 1		@ get IFSR
+	mov	pc, lr
+ENDPROC(v6_pabort)

arch/arm/mm/pabort-v7.S

+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/*
+ * Function: v6_pabort
+ *
+ * Params  : r0 = address of aborted instruction
+ *
+ * Returns : r0 = address of abort
+ *	   : r1 = IFSR
+ *
+ * Purpose : obtain information about current prefetch abort.
+ */
+
+	.align	5
+ENTRY(v7_pabort)
+	mrc	p15, 0, r0, c6, c0, 2		@ get IFAR
+	mrc	p15, 0, r1, c5, c0, 1		@ get IFSR
+	mov	pc, lr
+ENDPROC(v7_pabort)

arch/arm/mm/proc-arm1020.S

@@ -449,7 +449,7 @@ arm1020_crval:
 	.type	arm1020_processor_functions, #object
 arm1020_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1020_proc_init
 	.word	cpu_arm1020_proc_fin
 	.word	cpu_arm1020_reset

arch/arm/mm/proc-arm1020e.S

@@ -430,7 +430,7 @@ arm1020e_crval:
 	.type	arm1020e_processor_functions, #object
 arm1020e_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1020e_proc_init
 	.word	cpu_arm1020e_proc_fin
 	.word	cpu_arm1020e_reset

arch/arm/mm/proc-arm1022.S

@@ -413,7 +413,7 @@ arm1022_crval:
 	.type	arm1022_processor_functions, #object
 arm1022_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1022_proc_init
 	.word	cpu_arm1022_proc_fin
 	.word	cpu_arm1022_reset

arch/arm/mm/proc-arm1026.S

@@ -408,7 +408,7 @@ arm1026_crval:
 	.type	arm1026_processor_functions, #object
 arm1026_processor_functions:
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm1026_proc_init
 	.word	cpu_arm1026_proc_fin
 	.word	cpu_arm1026_reset

arch/arm/mm/proc-arm6_7.S

@@ -278,7 +278,7 @@ __arm7_setup:	mov	r0, #0
 		.type	arm6_processor_functions, #object
 ENTRY(arm6_processor_functions)
 		.word	cpu_arm6_data_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm6_proc_init
 		.word	cpu_arm6_proc_fin
 		.word	cpu_arm6_reset
@@ -295,7 +295,7 @@ ENTRY(arm6_processor_functions)
 		.type	arm7_processor_functions, #object
 ENTRY(arm7_processor_functions)
 		.word	cpu_arm7_data_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm7_proc_init
 		.word	cpu_arm7_proc_fin
 		.word	cpu_arm7_reset

arch/arm/mm/proc-arm720.S

@@ -181,7 +181,7 @@ arm720_crval:
 		.type	arm720_processor_functions, #object
 ENTRY(arm720_processor_functions)
 		.word	v4t_late_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm720_proc_init
 		.word	cpu_arm720_proc_fin
 		.word	cpu_arm720_reset

arch/arm/mm/proc-arm740.S

@@ -126,7 +126,7 @@ __arm740_setup:
 	.type	arm740_processor_functions, #object
 ENTRY(arm740_processor_functions)
 	.word	v4t_late_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm740_proc_init
 	.word	cpu_arm740_proc_fin
 	.word	cpu_arm740_reset

arch/arm/mm/proc-arm7tdmi.S

@@ -64,7 +64,7 @@ __arm7tdmi_setup:
 		.type	arm7tdmi_processor_functions, #object
 ENTRY(arm7tdmi_processor_functions)
 		.word	v4t_late_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm7tdmi_proc_init
 		.word	cpu_arm7tdmi_proc_fin
 		.word	cpu_arm7tdmi_reset

arch/arm/mm/proc-arm920.S

@@ -395,7 +395,7 @@ arm920_crval:
 	.type	arm920_processor_functions, #object
 arm920_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm920_proc_init
 	.word	cpu_arm920_proc_fin
 	.word	cpu_arm920_reset

arch/arm/mm/proc-arm922.S

@@ -399,7 +399,7 @@ arm922_crval:
 	.type	arm922_processor_functions, #object
 arm922_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm922_proc_init
 	.word	cpu_arm922_proc_fin
 	.word	cpu_arm922_reset

arch/arm/mm/proc-arm925.S

@@ -462,7 +462,7 @@ arm925_crval:
 	.type	arm925_processor_functions, #object
 arm925_processor_functions:
 	.word	v4t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm925_proc_init
 	.word	cpu_arm925_proc_fin
 	.word	cpu_arm925_reset

arch/arm/mm/proc-arm926.S

@@ -415,7 +415,7 @@ arm926_crval:
 	.type	arm926_processor_functions, #object
 arm926_processor_functions:
 	.word	v5tj_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm926_proc_init
 	.word	cpu_arm926_proc_fin
 	.word	cpu_arm926_reset

arch/arm/mm/proc-arm940.S

@@ -322,7 +322,7 @@ __arm940_setup:
 	.type	arm940_processor_functions, #object
 ENTRY(arm940_processor_functions)
 	.word	nommu_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm940_proc_init
 	.word	cpu_arm940_proc_fin
 	.word	cpu_arm940_reset

arch/arm/mm/proc-arm946.S

@@ -377,7 +377,7 @@ __arm946_setup:
 	.type	arm946_processor_functions, #object
 ENTRY(arm946_processor_functions)
 	.word	nommu_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_arm946_proc_init
 	.word	cpu_arm946_proc_fin
 	.word	cpu_arm946_reset

arch/arm/mm/proc-arm9tdmi.S

@@ -64,7 +64,7 @@ __arm9tdmi_setup:
 		.type	arm9tdmi_processor_functions, #object
 ENTRY(arm9tdmi_processor_functions)
 		.word	nommu_early_abort
-		.word	pabort_noifar
+		.word	legacy_pabort
 		.word	cpu_arm9tdmi_proc_init
 		.word	cpu_arm9tdmi_proc_fin
 		.word	cpu_arm9tdmi_reset

arch/arm/mm/proc-fa526.S

@@ -191,7 +191,7 @@ fa526_cr1_set:
 	.type	fa526_processor_functions, #object
 fa526_processor_functions:
 	.word	v4_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_fa526_proc_init
 	.word	cpu_fa526_proc_fin
 	.word	cpu_fa526_reset

arch/arm/mm/proc-feroceon.S

@@ -499,7 +499,7 @@ feroceon_crval:
 	.type	feroceon_processor_functions, #object
 feroceon_processor_functions:
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_feroceon_proc_init
 	.word	cpu_feroceon_proc_fin
 	.word	cpu_feroceon_reset

arch/arm/mm/proc-mohawk.S

@@ -359,7 +359,7 @@ mohawk_crval:
 	.type	mohawk_processor_functions, #object
 mohawk_processor_functions:
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_mohawk_proc_init
 	.word	cpu_mohawk_proc_fin
 	.word	cpu_mohawk_reset

arch/arm/mm/proc-sa110.S

@@ -199,7 +199,7 @@ sa110_crval:
 	.type	sa110_processor_functions, #object
 ENTRY(sa110_processor_functions)
 	.word	v4_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_sa110_proc_init
 	.word	cpu_sa110_proc_fin
 	.word	cpu_sa110_reset

arch/arm/mm/proc-sa1100.S

@@ -214,7 +214,7 @@ sa1100_crval:
 	.type	sa1100_processor_functions, #object
 ENTRY(sa1100_processor_functions)
 	.word	v4_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_sa1100_proc_init
 	.word	cpu_sa1100_proc_fin
 	.word	cpu_sa1100_reset

arch/arm/mm/proc-v6.S

@@ -191,7 +191,7 @@ v6_crval:
 	.type	v6_processor_functions, #object
 ENTRY(v6_processor_functions)
 	.word	v6_early_abort
-	.word	pabort_noifar
+	.word	v6_pabort
 	.word	cpu_v6_proc_init
 	.word	cpu_v6_proc_fin
 	.word	cpu_v6_reset

arch/arm/mm/proc-v7.S

@@ -295,7 +295,7 @@ __v7_setup_stack:
 	.type	v7_processor_functions, #object
 ENTRY(v7_processor_functions)
 	.word	v7_early_abort
-	.word	pabort_ifar
+	.word	v7_pabort
 	.word	cpu_v7_proc_init
 	.word	cpu_v7_proc_fin
 	.word	cpu_v7_reset

arch/arm/mm/proc-xsc3.S

@@ -428,7 +428,7 @@ xsc3_crval:
 	.type	xsc3_processor_functions, #object
 ENTRY(xsc3_processor_functions)
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_xsc3_proc_init
 	.word	cpu_xsc3_proc_fin
 	.word	cpu_xsc3_reset

arch/arm/mm/proc-xscale.S

@@ -511,7 +511,7 @@ xscale_crval:
 	.type	xscale_processor_functions, #object
 ENTRY(xscale_processor_functions)
 	.word	v5t_early_abort
-	.word	pabort_noifar
+	.word	legacy_pabort
 	.word	cpu_xscale_proc_init
 	.word	cpu_xscale_proc_fin
 	.word	cpu_xscale_reset

arch/arm/plat-iop/pci.c

@@ -257,7 +257,8 @@ void __init iop3xx_atu_setup(void)
 	*IOP3XX_OUMWTVR0 = 0;
 
 	/* Outbound window 1 */
-	*IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_BA + IOP3XX_PCI_MEM_WINDOW_SIZE;
+	*IOP3XX_OMWTVR1 = IOP3XX_PCI_LOWER_MEM_BA +
+			  IOP3XX_PCI_MEM_WINDOW_SIZE / 2;
 	*IOP3XX_OUMWTVR1 = 0;
 
 	/* BAR 3 ( Disabled ) */

arch/arm/plat-iop/time.c

@@ -85,7 +85,7 @@ void __init iop_init_time(unsigned long tick_rate)
 {
 	u32 timer_ctl;
 
-	ticks_per_jiffy = (tick_rate + HZ/2) / HZ;
+	ticks_per_jiffy = DIV_ROUND_CLOSEST(tick_rate, HZ);
 	ticks_per_usec = tick_rate / 1000000;
 	next_jiffy_time = 0xffffffff;
 	iop_tick_rate = tick_rate;

drivers/mmc/host/mmci.c

@@ -678,7 +678,6 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
 	writel(0, host->base + MMCIMASK1);
 	writel(0xfff, host->base + MMCICLEAR);
 
-#ifdef CONFIG_GPIOLIB
 	if (gpio_is_valid(plat->gpio_cd)) {
 		ret = gpio_request(plat->gpio_cd, DRIVER_NAME " (cd)");
 		if (ret == 0)
@@ -697,7 +696,6 @@ static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
 		else if (ret != -ENOSYS)
 			goto err_gpio_wp;
 	}
-#endif
 
 	ret = request_irq(dev->irq[0], mmci_irq, IRQF_SHARED, DRIVER_NAME " (cmd)", host);
 	if (ret)

drivers/pcmcia/sa1100_assabet.c

@@ -130,7 +130,7 @@ static struct pcmcia_low_level assabet_pcmcia_ops = {
 	.socket_suspend		= assabet_pcmcia_socket_suspend,
 };
 
-int __init pcmcia_assabet_init(struct device *dev)
+int pcmcia_assabet_init(struct device *dev)
 {
 	int ret = -ENODEV;
 

drivers/pcmcia/sa1100_neponset.c

@@ -123,7 +123,7 @@ static struct pcmcia_low_level neponset_pcmcia_ops = {
 	.socket_suspend 	= sa1111_pcmcia_socket_suspend,
 };
 
-int __init pcmcia_neponset_init(struct sa1111_dev *sadev)
+int pcmcia_neponset_init(struct sa1111_dev *sadev)
 {
 	int ret = -ENODEV;
 

drivers/serial/sa1100.c

@@ -638,7 +638,7 @@ static void __init sa1100_init_ports(void)
 	PPSR |= PPC_TXD1 | PPC_TXD3;
 }
 
-void __init sa1100_register_uart_fns(struct sa1100_port_fns *fns)
+void __devinit sa1100_register_uart_fns(struct sa1100_port_fns *fns)
 {
 	if (fns->get_mctrl)
 		sa1100_pops.get_mctrl = fns->get_mctrl;