Merge tag 's5pv210-dt' of...

Merge tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc

Merge "Samsung S5PV210 DT support for v3.17" from Kukjin Kim:

- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210

* tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  clk: samsung: s5pv210: Remove legacy board support
  ARM: SAMSUNG: Remove remaining legacy code
  gpio: samsung: Remove legacy support of S5PV210
  ARM: S5PV210: Enable multi-platform build support
  cpufreq: s5pv210: Make the driver multiplatform aware
  ARM: S5PV210: Register cpufreq platform device
  ARM: S5PV210: move debug-macro.S into the common space
  ARM: S5PV210: Untie PM support from legacy code
  ARM: S5PV210: Remove support for board files
  ARM: dts: Add Device tree for s5pc110/s5pv210 boards
  ARM: dts: Add Device tree for s5pv210 SoC
  ARM: S5PV210: Add board file for boot using Device Tree
  phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
  clk: samsung: Add S5PV210 Audio Subsystem clock driver
  ARM: SAMSUNG: Remove legacy clock code
  serial: samsung: Remove support for legacy clock code
  cpufreq: s3c24xx: Remove some dead code
  ARM: S5PV210: Migrate clock handling to Common Clock Framework
  clk: samsung: Add clock driver for S5PV210 and compatible SoCs
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt

+* Samsung Audio Subsystem Clock Controller
+
+The Samsung Audio Subsystem clock controller generates and supplies clocks
+to Audio Subsystem block available in the S5PV210 and compatible SoCs.
+
+Required Properties:
+
+- compatible: should be "samsung,s5pv210-audss-clock".
+- reg: physical base address and length of the controller's register set.
+
+- #clock-cells: should be 1.
+
+- clocks:
+  - hclk: AHB bus clock of the Audio Subsystem.
+  - xxti: Optional fixed rate PLL reference clock, parent of mout_audss. If
+    not specified (i.e. xusbxti is used for PLL reference), it is fixed to
+    a clock named "xxti".
+  - fout_epll: Input PLL to the AudioSS block, parent of mout_audss.
+  - iiscdclk0: Optional external i2s clock, parent of mout_i2s. If not
+    specified, it is fixed to a clock named "iiscdclk0".
+  - sclk_audio0: Audio bus clock, parent of mout_i2s.
+
+- clock-names: Aliases for the above clocks. They should be "hclk",
+  "xxti", "fout_epll", "iiscdclk0", and "sclk_audio0" respectively.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/s5pv210-audss-clk.h header and can be used in device
+tree sources.
+
+Example: Clock controller node.
+
+	clk_audss: clock-controller@c0900000 {
+		compatible = "samsung,s5pv210-audss-clock";
+		reg = <0xc0900000 0x1000>;
+		#clock-cells = <1>;
+		clock-names = "hclk", "xxti",
+				"fout_epll", "sclk_audio0";
+		clocks = <&clocks DOUT_HCLKP>, <&xxti>,
+				<&clocks FOUT_EPLL>, <&clocks SCLK_AUDIO0>;
+	};
+
+Example: I2S controller node that consumes the clock generated by the clock
+	 controller. Refer to the standard clock bindings for information
+         about 'clocks' and 'clock-names' property.
+
+	i2s0: i2s@03830000 {
+		/* ... */
+		clock-names = "iis", "i2s_opclk0",
+				"i2s_opclk1";
+		clocks = <&clk_audss CLK_I2S>, <&clk_audss CLK_I2S>,
+				<&clk_audss CLK_DOUT_AUD_BUS>;
+		/* ... */
+	};

Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt

+* Samsung S5P6442/S5PC110/S5PV210 Clock Controller
+
+Samsung S5P6442, S5PC110 and S5PV210 SoCs contain integrated clock
+controller, which generates and supplies clock to various controllers
+within the SoC.
+
+Required Properties:
+
+- compatible: should be one of following:
+	- "samsung,s5pv210-clock" : for clock controller of Samsung
+	  S5PC110/S5PV210 SoCs,
+	- "samsung,s5p6442-clock" : for clock controller of Samsung
+	  S5P6442 SoC.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- #clock-cells: should be 1.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/s5pv210.h header and can be used in device tree sources.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xxti": external crystal oscillator connected to XXTI and XXTO pins of
+the SoC,
+ - "xusbxti": external crystal oscillator connected to XUSBXTI and XUSBXTO
+pins of the SoC,
+
+A subset of above clocks available on given board shall be specified in
+board device tree, including the system base clock, as selected by XOM[0]
+pin of the SoC. Refer to generic fixed rate clock bindings
+documentation[1] for more information how to specify these clocks.
+
+[1] Documentation/devicetree/bindings/clock/fixed-clock.txt
+
+Example: Clock controller node:
+
+	clock: clock-controller@7e00f000 {
+		compatible = "samsung,s5pv210-clock";
+		reg = <0x7e00f000 0x1000>;
+		#clock-cells = <1>;
+	};
+
+Example: Required external clocks:
+
+	xxti: clock-xxti {
+		compatible = "fixed-clock";
+		clock-output-names = "xxti";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+	xusbxti: clock-xusbxti {
+		compatible = "fixed-clock";
+		clock-output-names = "xusbxti";
+		clock-frequency = <24000000>;
+		#clock-cells = <0>;
+	};
+
+Example: UART controller node that consumes the clock generated by the clock
+  controller (refer to the standard clock bindings for information about
+  "clocks" and "clock-names" properties):
+
+	uart0: serial@e2900000 {
+		compatible = "samsung,s5pv210-uart";
+		reg = <0xe2900000 0x400>;
+		interrupt-parent = <&vic1>;
+		interrupts = <10>;
+		clock-names = "uart", "clk_uart_baud0",
+				"clk_uart_baud1";
+		clocks = <&clocks UART0>, <&clocks UART0>,
+				<&clocks SCLK_UART0>;
+		status = "disabled";
+	};

Documentation/devicetree/bindings/phy/samsung-phy.txt

@@ -26,6 +26,7 @@ Samsung S5P/EXYNOS SoC series USB PHY
 
 Required properties:
 - compatible : should be one of the listed compatibles:
+	- "samsung,s5pv210-usb2-phy"
 	- "samsung,exynos4210-usb2-phy"
 	- "samsung,exynos4x12-usb2-phy"
 	- "samsung,exynos5250-usb2-phy"

arch/arm/Kconfig

@@ -744,25 +744,6 @@ config ARCH_S3C64XX
 	help
 	  Samsung S3C64XX series based systems
 
-config ARCH_S5PV210
-	bool "Samsung S5PV210/S5PC110"
-	select ARCH_HAS_HOLES_MEMORYMODEL
-	select ARCH_SPARSEMEM_ENABLE
-	select ATAGS
-	select CLKDEV_LOOKUP
-	select CLKSRC_SAMSUNG_PWM
-	select CPU_V7
-	select GENERIC_CLOCKEVENTS
-	select GPIO_SAMSUNG
-	select HAVE_S3C2410_I2C if I2C
-	select HAVE_S3C2410_WATCHDOG if WATCHDOG
-	select HAVE_S3C_RTC if RTC_CLASS
-	select NEED_MACH_GPIO_H
-	select NEED_MACH_MEMORY_H
-	select SAMSUNG_ATAGS
-	help
-	  Samsung S5PV210/S5PC110 series based systems
-
 config ARCH_DAVINCI
 	bool "TI DaVinci"
 	select ARCH_HAS_HOLES_MEMORYMODEL
@@ -1500,7 +1481,8 @@ config ARM_PSCI
 config ARCH_NR_GPIO
 	int
 	default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
-	default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX
+	default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || \
+		SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
 	default 416 if ARCH_SUNXI
 	default 392 if ARCH_U8500
 	default 352 if ARCH_VT8500

arch/arm/Kconfig.debug

@@ -617,6 +617,7 @@ choice
 		depends on PLAT_SAMSUNG
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
+		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 0 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
@@ -627,6 +628,7 @@ choice
 		depends on PLAT_SAMSUNG
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
+		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 1 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
@@ -637,6 +639,7 @@ choice
 		depends on PLAT_SAMSUNG
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
 		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
+		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 2 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
@@ -644,8 +647,9 @@ choice
 		  by the boot-loader before use.
 
 	config DEBUG_S3C_UART3
-		depends on PLAT_SAMSUNG && ARCH_EXYNOS
-		select DEBUG_EXYNOS_UART
+		depends on PLAT_SAMSUNG && (ARCH_EXYNOS || ARCH_S5PV210)
+		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
+		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 3 for low-level debug"
 		help
 		  Say Y here if you want the debug print routines to direct
@@ -945,6 +949,9 @@ config DEBUG_S3C2410_UART
 config DEBUG_S3C24XX_UART
 	bool
 
+config DEBUG_S5PV210_UART
+	bool
+
 config DEBUG_OMAP2PLUS_UART
 	bool
 	depends on ARCH_OMAP2PLUS
@@ -1005,6 +1012,7 @@ config DEBUG_LL_INCLUDE
 	default "debug/msm.S" if DEBUG_MSM_UART || DEBUG_QCOM_UARTDM
 	default "debug/omap2plus.S" if DEBUG_OMAP2PLUS_UART
 	default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART
+	default "debug/s5pv210.S" if DEBUG_S5PV210_UART
 	default "debug/sirf.S" if DEBUG_SIRFPRIMA2_UART1 || DEBUG_SIRFMARCO_UART1
 	default "debug/sti.S" if DEBUG_STI_UART
 	default "debug/tegra.S" if DEBUG_TEGRA_UART

arch/arm/Makefile

@@ -210,11 +210,11 @@ machine-$(CONFIG_PLAT_SPEAR)		+= spear
 plat-$(CONFIG_ARCH_EXYNOS)	+= samsung
 plat-$(CONFIG_ARCH_OMAP)	+= omap
 plat-$(CONFIG_ARCH_S3C64XX)	+= samsung
+plat-$(CONFIG_ARCH_S5PV210)	+= samsung
 plat-$(CONFIG_PLAT_IOP)		+= iop
 plat-$(CONFIG_PLAT_ORION)	+= orion
 plat-$(CONFIG_PLAT_PXA)		+= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	+= samsung
-plat-$(CONFIG_PLAT_S5P)		+= samsung
 plat-$(CONFIG_PLAT_VERSATILE)	+= versatile
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
@@ -238,7 +238,7 @@ MACHINE  :=
 endif
 
 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
-platdirs := $(patsubst %,arch/arm/plat-%/,$(plat-y))
+platdirs := $(patsubst %,arch/arm/plat-%/,$(sort $(plat-y)))
 
 ifneq ($(CONFIG_ARCH_MULTIPLATFORM),y)
 ifeq ($(KBUILD_SRC),)

arch/arm/boot/dts/Makefile

@@ -318,6 +318,11 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
 dtb-$(CONFIG_ARCH_S3C64XX) += s3c6410-mini6410.dtb \
 	s3c6410-smdk6410.dtb
+dtb-$(CONFIG_ARCH_S5PV210) += s5pv210-aquila.dtb \
+	s5pv210-goni.dtb \
+	s5pv210-smdkc110.dtb \
+	s5pv210-smdkv210.dtb \
+	s5pv210-torbreck.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += r7s72100-genmai.dtb \
 	r8a7740-armadillo800eva.dtb \
 	r8a7778-bockw.dtb \

arch/arm/boot/dts/s5pv210-aquila.dts

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Board device tree source for Samsung Aquila board.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "s5pv210.dtsi"
+
+/ {
+	model = "Samsung Aquila based on S5PC110";
+	compatible = "samsung,aquila", "samsung,s5pv210";
+
+	aliases {
+		i2c3 = &i2c_pmic;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC2,115200n8 root=/dev/mmcblk1p5 rw rootwait ignore_loglevel earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x30000000 0x05000000
+			0x40000000 0x18000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vtf_reg: fixed-regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "V_TF_2.8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpios = <&mp05 4 0>;
+			enable-active-high;
+		};
+
+		pda_reg: fixed-regulator@1 {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_1.8V_PDA";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			reg = <1>;
+		};
+
+		bat_reg: fixed-regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "V_BAT";
+			regulator-min-microvolt = <3700000>;
+			regulator-max-microvolt = <3700000>;
+			reg = <2>;
+		};
+	};
+
+	i2c_pmic: i2c-pmic {
+		compatible = "i2c-gpio";
+		gpios = <&gpj4 0 0>, /* sda */
+			<&gpj4 3 0>; /* scl */
+		i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmic@66 {
+			compatible = "national,lp3974";
+			reg = <0x66>;
+
+			max8998,pmic-buck1-default-dvs-idx = <0>;
+			max8998,pmic-buck1-dvs-gpios = <&gph0 3 0>,
+							<&gph0 4 0>;
+			max8998,pmic-buck1-dvs-voltage = <1200000>, <1200000>,
+							<1200000>, <1200000>;
+
+			max8998,pmic-buck2-default-dvs-idx = <0>;
+			max8998,pmic-buck2-dvs-gpio = <&gph0 5 0>;
+			max8998,pmic-buck2-dvs-voltage = <1200000>, <1200000>;
+
+			regulators {
+				ldo2_reg: LDO2 {
+					regulator-name = "VALIVE_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VUSB+MIPI_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VADC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "VTF_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "VCC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VCC_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "VUSB+VDAC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "VCC+VCAM_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "VPLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "CAM_IO_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "CAM_ISP_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "CAM_A_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "CAM_CIF_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "CAM_AF_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "VMIPI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "CAM_8M_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "VARM_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "VINT_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "VCC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "CAM_CORE_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				vichg_reg: ENVICHG {
+					regulator-name = "VICHG";
+				};
+
+				safeout1_reg: ESAFEOUT1 {
+					regulator-name = "SAFEOUT1";
+					regulator-always-on;
+				};
+
+				safeout2_reg: ESAFEOUT2 {
+					regulator-name = "SAFEOUT2";
+					regulator-boot-on;
+				};
+			};
+		};
+
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power-key {
+			gpios = <&gph2 6 1>;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			debounce-interval = <1>;
+			gpio-key,wakeup;
+		};
+	};
+};
+
+&xusbxti {
+	clock-frequency = <24000000>;
+};
+
+&keypad {
+	linux,input-no-autorepeat;
+	linux,input-wakeup;
+	samsung,keypad-num-rows = <3>;
+	samsung,keypad-num-columns = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&keypad_row0>, <&keypad_row1>, <&keypad_row2>,
+			<&keypad_col0>, <&keypad_col1>, <&keypad_col2>;
+	status = "okay";
+
+	key_1 {
+		keypad,row = <0>;
+		keypad,column = <1>;
+		linux,code = <KEY_CONNECT>;
+	};
+
+	key_2 {
+		keypad,row = <0>;
+		keypad,column = <2>;
+		linux,code = <KEY_BACK>;
+	};
+
+	key_3 {
+		keypad,row = <1>;
+		keypad,column = <1>;
+		linux,code = <KEY_CAMERA_FOCUS>;
+	};
+
+	key_4 {
+		keypad,row = <1>;
+		keypad,column = <2>;
+		linux,code = <KEY_VOLUMEUP>;
+	};
+
+	key_5 {
+		keypad,row = <2>;
+		keypad,column = <1>;
+		linux,code = <KEY_CAMERA>;
+	};
+
+	key_6 {
+		keypad,row = <2>;
+		keypad,column = <2>;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&sdhci0 {
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+	vmmc-supply = <&ldo5_reg>;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+	pinctrl-names = "default";
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	cd-gpios = <&gph3 4 1>;
+	vmmc-supply = <&vtf_reg>;
+	cd-inverted;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &t_flash_detect>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&onenand {
+	status = "okay";
+};
+
+&hsotg {
+	vusb_a-supply = <&ldo3_reg>;
+	vusb_d-supply = <&ldo8_reg>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&fimd {
+	pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	display-timings {
+		native-mode = <&timing0>;
+		timing0: timing {
+			clock-frequency = <0>;
+			hactive = <800>;
+			vactive = <480>;
+			hfront-porch = <16>;
+			hback-porch = <16>;
+			hsync-len = <2>;
+			vback-porch = <3>;
+			vfront-porch = <28>;
+			vsync-len = <1>;
+		};
+	};
+};
+
+&pinctrl0 {
+	t_flash_detect: t-flash-detect {
+		samsung,pins = "gph3-4";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+	};
+};

arch/arm/boot/dts/s5pv210-goni.dts

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Board device tree source for Samsung Goni board.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "s5pv210.dtsi"
+
+/ {
+	model = "Samsung Goni based on S5PC110";
+	compatible = "samsung,goni", "samsung,s5pv210";
+
+	aliases {
+		i2c3 = &i2c_pmic;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC0,115200n8 root=/dev/mmcblk0p5 rw rootwait ignore_loglevel earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x30000000 0x05000000
+			0x40000000 0x10000000
+			0x50000000 0x08000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vtf_reg: fixed-regulator@0 {
+			compatible = "regulator-fixed";
+			regulator-name = "V_TF_2.8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			reg = <0>;
+			gpios = <&mp05 4 0>;
+			enable-active-high;
+		};
+
+		pda_reg: fixed-regulator@1 {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC_1.8V_PDA";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			reg = <1>;
+		};
+
+		bat_reg: fixed-regulator@2 {
+			compatible = "regulator-fixed";
+			regulator-name = "V_BAT";
+			regulator-min-microvolt = <3700000>;
+			regulator-max-microvolt = <3700000>;
+			reg = <2>;
+		};
+
+		tsp_reg: fixed-regulator@3 {
+			compatible = "regulator-fixed";
+			regulator-name = "TSP_VDD";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			reg = <3>;
+			gpios = <&gpj1 3 0>;
+			enable-active-high;
+		};
+	};
+
+	i2c_pmic: i2c-pmic {
+		compatible = "i2c-gpio";
+		gpios = <&gpj4 0 0>, /* sda */
+			<&gpj4 3 0>; /* scl */
+		i2c-gpio,delay-us = <2>;        /* ~100 kHz */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmic@66 {
+			compatible = "national,lp3974";
+			reg = <0x66>;
+
+			max8998,pmic-buck1-default-dvs-idx = <0>;
+			max8998,pmic-buck1-dvs-gpios = <&gph0 3 0>,
+							<&gph0 4 0>;
+			max8998,pmic-buck1-dvs-voltage = <1200000>, <1200000>,
+							<1200000>, <1200000>;
+
+			max8998,pmic-buck2-default-dvs-idx = <0>;
+			max8998,pmic-buck2-dvs-gpio = <&gph0 5 0>;
+			max8998,pmic-buck2-dvs-voltage = <1200000>, <1200000>;
+
+			regulators {
+				ldo2_reg: LDO2 {
+					regulator-name = "VALIVE_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VUSB+MIPI_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VADC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "VTF_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "VCC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VLCD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "VUSB+VDAC_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "VCC+VCAM_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "VPLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-boot-on;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "CAM_IO_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "CAM_ISP_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "CAM_A_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "CAM_CIF_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "CAM_AF_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "VMIPI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "CAM_8M_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "VARM_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "VINT_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "VCC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "CAM_CORE_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		power-key {
+			gpios = <&gph2 6 1>;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			debounce-interval = <1>;
+			gpio-key,wakeup;
+		};
+	};
+};
+
+&xusbxti {
+	clock-frequency = <24000000>;
+};
+
+&keypad {
+	linux,input-no-autorepeat;
+	linux,input-wakeup;
+	samsung,keypad-num-rows = <3>;
+	samsung,keypad-num-columns = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&keypad_row0>, <&keypad_row1>, <&keypad_row2>,
+			<&keypad_col0>, <&keypad_col1>, <&keypad_col2>;
+	status = "okay";
+
+	key_1 {
+		keypad,row = <0>;
+		keypad,column = <1>;
+		linux,code = <KEY_CONNECT>;
+	};
+
+	key_2 {
+		keypad,row = <0>;
+		keypad,column = <2>;
+		linux,code = <KEY_BACK>;
+	};
+
+	key_3 {
+		keypad,row = <1>;
+		keypad,column = <1>;
+		linux,code = <KEY_CAMERA_FOCUS>;
+	};
+
+	key_4 {
+		keypad,row = <1>;
+		keypad,column = <2>;
+		linux,code = <KEY_VOLUMEUP>;
+	};
+
+	key_5 {
+		keypad,row = <2>;
+		keypad,column = <1>;
+		linux,code = <KEY_CAMERA>;
+	};
+
+	key_6 {
+		keypad,row = <2>;
+		keypad,column = <2>;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&sdhci0 {
+	bus-width = <4>;
+	non-removable;
+	vmmc-supply = <&ldo5_reg>;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus1 &sd0_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	cd-gpios = <&gph3 4 1>;
+	vmmc-supply = <&vtf_reg>;
+	cd-inverted;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hsotg {
+	vusb_a-supply = <&ldo3_reg>;
+	vusb_d-supply = <&ldo8_reg>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&i2c2 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <400000>;
+	samsung,i2c-slave-addr = <0x10>;
+	status = "okay";
+
+	tsp@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		interrupt-parent = <&gpj0>;
+		interrupts = <5 2>;
+
+		atmel,x-line = <17>;
+		atmel,y-line = <11>;
+		atmel,x-size = <800>;
+		atmel,y-size = <480>;
+		atmel,burst-length = <0x21>;
+		atmel,threshold = <0x28>;
+		atmel,orientation = <1>;
+
+		vdd-supply = <&tsp_reg>;
+	};
+};
+
+&i2c0 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-max-bus-freq = <100000>;
+	samsung,i2c-slave-addr = <0x10>;
+	status = "okay";
+
+	noon010pc30: sensor@30 {
+		compatible = "siliconfile,noon010pc30";
+		reg = <0x30>;
+		vddio-supply = <&ldo11_reg>;
+		vdda-supply = <&ldo13_reg>;
+		vdd_core-supply = <&ldo14_reg>;
+
+		clock-frequency = <16000000>;
+		clocks = <&clock_cam 0>;
+		clock-names = "mclk";
+		nreset-gpios = <&gpb 2 0>;
+		nstby-gpios = <&gpb 0 0>;
+
+		port {
+			noon010pc30_ep: endpoint {
+				remote-endpoint = <&fimc0_ep>;
+				bus-width = <8>;
+				hsync-active = <0>;
+				vsync-active = <1>;
+				pclk-sample = <1>;
+			};
+		};
+	};
+};
+
+&camera {
+	pinctrl-0 = <&cam_port_a_io &cam_port_a_clk_active>;
+	pinctrl-1 = <&cam_port_a_io &cam_port_a_clk_idle>;
+	pinctrl-names = "default", "idle";
+
+	parallel-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* camera A input */
+		port@1 {
+			reg = <1>;
+			fimc0_ep: endpoint {
+				remote-endpoint = <&noon010pc30_ep>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				pclk-sample = <0>;
+			};
+		};
+	};
+};
+
+&fimd {
+	pinctrl-0 = <&lcd_clk &lcd_data24>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	display-timings {
+		native-mode = <&timing0>;
+		timing0: timing {
+			/* 480x800@55Hz */
+			clock-frequency = <23439570>;
+			hactive = <480>;
+			hfront-porch = <16>;
+			hback-porch = <16>;
+			hsync-len = <2>;
+			vactive = <800>;
+			vback-porch = <2>;
+			vfront-porch = <28>;
+			vsync-len = <1>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <0>;
+			pixelclk-active = <0>;
+		};
+	};
+};
+
+&onenand {
+	status = "okay";
+};

arch/arm/boot/dts/s5pv210-pinctrl.dtsi

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Samsung's S5PV210 SoC device nodes are listed in this file. S5PV210
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S5PV210 SoC. As device tree coverage for S5PV210 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+&pinctrl0 {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb: gpb {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc0: gpc0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe0: gpe0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpe1: gpe1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf0: gpf0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf2: gpf2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf3: gpf3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg0: gpg0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj0: gpj0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj1: gpj1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj2: gpj2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj3: gpj3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpj4: gpj4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpgi: gpgi {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp01: mp01 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp02: mp02 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp03: mp03 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp04: mp04 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp05: mp05 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp06: mp06 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	mp07: mp07 {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gph0: gph0 {
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&vic0>;
+		interrupts = <0>, <1>, <2>, <3>,
+				<4>, <5>, <6>, <7>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+	gph1: gph1 {
+		gpio-controller;
+		interrupt-controller;
+		interrupt-parent = <&vic0>;
+		interrupts = <8>, <9>, <10>, <11>,
+				<12>, <13>, <14>, <15>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+	gph2: gph2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+	gph3: gph3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+
+	uart0_data: uart0-data {
+		samsung,pins = "gpa0-0", "gpa0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart0_fctl: uart0-fctl {
+		samsung,pins = "gpa0-2", "gpa0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_data: uart1-data {
+		samsung,pins = "gpa0-4", "gpa0-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart1_fctl: uart1-fctl {
+		samsung,pins = "gpa0-6", "gpa0-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart2_data: uart2-data {
+		samsung,pins = "gpa1-0", "gpa1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart2_fctl: uart2-fctl {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart3_data: uart3-data {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	uart_audio: uart-audio {
+		samsung,pins = "gpa1-2", "gpa1-3";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_bus: spi1-bus {
+		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s0_bus: i2s0-bus {
+		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
+				"gpi-4", "gpi-5", "gpi-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s1_bus: i2s1-bus {
+		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+				"gpc0-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s2_bus: i2s2-bus {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pcm1_bus: pcm1-bus {
+		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+				"gpc0-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	ac97_bus: ac97-bus {
+		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+				"gpc0-4";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2s2_bus: i2s2-bus {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pcm2_bus: pcm2-bus {
+		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+				"gpc1-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	spdif_bus: spdif-bus {
+		samsung,pins = "gpc1-0", "gpc1-1";
+		samsung,pin-function = <4>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi2_bus: spi2-bus {
+		samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
+		samsung,pin-function = <5>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c0_bus: i2c0-bus {
+		samsung,pins = "gpd1-0", "gpd1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c1_bus: i2c1-bus {
+		samsung,pins = "gpd1-2", "gpd1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c2_bus: i2c2-bus {
+		samsung,pins = "gpd1-4", "gpd1-5";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm0_out: pwm0-out {
+		samsung,pins = "gpd0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm1_out: pwm1-out {
+		samsung,pins = "gpd0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm2_out: pwm2-out {
+		samsung,pins = "gpd0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	pwm3_out: pwm3-out {
+		samsung,pins = "gpd0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row0: keypad-row-0 {
+		samsung,pins = "gph3-0";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row1: keypad-row-1 {
+		samsung,pins = "gph3-1";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row2: keypad-row-2 {
+		samsung,pins = "gph3-2";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row3: keypad-row-3 {
+		samsung,pins = "gph3-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row4: keypad-row-4 {
+		samsung,pins = "gph3-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row5: keypad-row-5 {
+		samsung,pins = "gph3-5";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row6: keypad-row-6 {
+		samsung,pins = "gph3-6";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_row7: keypad-row-7 {
+		samsung,pins = "gph3-7";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col0: keypad-col-0 {
+		samsung,pins = "gph2-0";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col1: keypad-col-1 {
+		samsung,pins = "gph2-1";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col2: keypad-col-2 {
+		samsung,pins = "gph2-2";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col3: keypad-col-3 {
+		samsung,pins = "gph2-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col4: keypad-col-4 {
+		samsung,pins = "gph2-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col5: keypad-col-5 {
+		samsung,pins = "gph2-5";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col6: keypad-col-6 {
+		samsung,pins = "gph2-6";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	keypad_col7: keypad-col-7 {
+		samsung,pins = "gph2-7";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpg0-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpg0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cd: sd0-cd {
+		samsung,pins = "gpg0-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus1: sd0-bus-width1 {
+		samsung,pins = "gpg0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus4: sd0-bus-width4 {
+		samsung,pins = "gpg0-3", "gpg0-4", "gpg0-5", "gpg0-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus8: sd0-bus-width8 {
+		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_clk: sd1-clk {
+		samsung,pins = "gpg1-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cmd: sd1-cmd {
+		samsung,pins = "gpg1-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_cd: sd1-cd {
+		samsung,pins = "gpg1-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus1: sd1-bus-width1 {
+		samsung,pins = "gpg1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd1_bus4: sd1-bus-width4 {
+		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_clk: sd2-clk {
+		samsung,pins = "gpg2-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cmd: sd2-cmd {
+		samsung,pins = "gpg2-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_cd: sd2-cd {
+		samsung,pins = "gpg2-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus1: sd2-bus-width1 {
+		samsung,pins = "gpg2-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus4: sd2-bus-width4 {
+		samsung,pins = "gpg2-3", "gpg2-4", "gpg2-5", "gpg2-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_bus8: sd2-bus-width8 {
+		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd3_clk: sd3-clk {
+		samsung,pins = "gpg3-0";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd3_cmd: sd3-cmd {
+		samsung,pins = "gpg3-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd3_cd: sd3-cd {
+		samsung,pins = "gpg3-2";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd3_bus1: sd3-bus-width1 {
+		samsung,pins = "gpg3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd3_bus4: sd3-bus-width4 {
+		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <2>;
+		samsung,pin-drv = <3>;
+	};
+
+	eint0: ext-int0 {
+		samsung,pins = "gph0-0";
+		samsung,pin-function = <0xf>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	eint8: ext-int8 {
+		samsung,pins = "gph1-0";
+		samsung,pin-function = <0xf>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	eint15: ext-int15 {
+		samsung,pins = "gph1-7";
+		samsung,pin-function = <0xf>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	eint16: ext-int16 {
+		samsung,pins = "gph2-0";
+		samsung,pin-function = <0xf>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	eint31: ext-int31 {
+		samsung,pins = "gph3-7";
+		samsung,pin-function = <0xf>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_port_a_io: cam-port-a-io {
+		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
+				"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
+				"gpe1-0", "gpe1-1", "gpe1-2", "gpe1-4";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_port_a_clk_active: cam-port-a-clk-active {
+		samsung,pins = "gpe1-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	cam_port_a_clk_idle: cam-port-a-clk-idle {
+		samsung,pins = "gpe1-3";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_port_b_io: cam-port-b-io {
+		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
+				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
+				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	cam_port_b_clk_active: cam-port-b-clk-active {
+		samsung,pins = "gpj1-3";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <3>;
+	};
+
+	cam_port_b_clk_idle: cam-port-b-clk-idle {
+		samsung,pins = "gpj1-3";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <1>;
+		samsung,pin-drv = <0>;
+	};
+
+		lcd_ctrl: lcd-ctrl {
+		samsung,pins = "gpd0-0", "gpd0-1";
+		samsung,pin-function = <3>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	lcd_sync: lcd-sync {
+		samsung,pins = "gpf0-0", "gpf0-1";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	lcd_clk: lcd-clk {
+		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	lcd_data24: lcd-data-width24 {
+		samsung,pins =  "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
+				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
+				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
+				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
+				"gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7",
+				"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+};

arch/arm/boot/dts/s5pv210-smdkc110.dts

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Board device tree source for YIC System SMDC110 board.
+ *
+ * NOTE: This file is completely based on original board file for mach-smdkc110
+ * available in Linux 3.15 and intends to provide equivalent level of hardware
+ * support. Due to lack of hardware, _no_ testing has been performed.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "s5pv210.dtsi"
+
+/ {
+	model = "YIC System SMDKC110 based on S5PC110";
+	compatible = "yic,smdkc110", "samsung,s5pv210";
+
+	chosen {
+		bootargs = "console=ttySAC0,115200n8 root=/dev/mmcblk0p1 rw rootwait ignore_loglevel earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x20000000 0x20000000>;
+	};
+};
+
+&xusbxti {
+	clock-frequency = <24000000>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	audio-codec@1b {
+		compatible = "wlf,wm8580";
+		reg = <0x1b>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+	};
+};
+
+&i2s0 {
+	status = "okay";
+};

arch/arm/boot/dts/s5pv210-smdkv210.dts

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Board device tree source for YIC System SMDV210 board.
+ *
+ * NOTE: This file is completely based on original board file for mach-smdkv210
+ * available in Linux 3.15 and intends to provide equivalent level of hardware
+ * support. Due to lack of hardware, _no_ testing has been performed.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "s5pv210.dtsi"
+
+/ {
+	model = "YIC System SMDKV210 based on S5PV210";
+	compatible = "yic,smdkv210", "samsung,s5pv210";
+
+	chosen {
+		bootargs = "console=ttySAC0,115200n8 root=/dev/mmcblk0p1 rw rootwait ignore_loglevel earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x20000000 0x40000000>;
+	};
+
+	ethernet@18000000 {
+		compatible = "davicom,dm9000";
+		reg = <0xA8000000 0x2 0xA8000002 0x2>;
+		interrupt-parent = <&gph1>;
+		interrupts = <1 4>;
+		local-mac-address = [00 00 de ad be ef];
+		davicom,no-eeprom;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwm3_out>;
+	};
+};
+
+&xusbxti {
+	clock-frequency = <24000000>;
+};
+
+&keypad {
+	linux,input-no-autorepeat;
+	linux,input-wakeup;
+	samsung,keypad-num-rows = <8>;
+	samsung,keypad-num-columns = <8>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&keypad_row0>, <&keypad_row1>, <&keypad_row2>,
+			<&keypad_row3>, <&keypad_row4>, <&keypad_row5>,
+			<&keypad_row6>, <&keypad_row7>,
+			<&keypad_col0>, <&keypad_col1>, <&keypad_col2>,
+			<&keypad_col3>, <&keypad_col4>, <&keypad_col5>,
+			<&keypad_col6>, <&keypad_col7>;
+	status = "okay";
+
+	key_1 {
+		keypad,row = <0>;
+		keypad,column = <3>;
+		linux,code = <KEY_1>;
+	};
+
+	key_2 {
+		keypad,row = <0>;
+		keypad,column = <4>;
+		linux,code = <KEY_2>;
+	};
+
+	key_3 {
+		keypad,row = <0>;
+		keypad,column = <5>;
+		linux,code = <KEY_3>;
+	};
+
+	key_4 {
+		keypad,row = <0>;
+		keypad,column = <6>;
+		linux,code = <KEY_4>;
+	};
+
+	key_5 {
+		keypad,row = <0
+		>;
+		keypad,column = <7>;
+		linux,code = <KEY_5>;
+	};
+
+	key_6 {
+		keypad,row = <1>;
+		keypad,column = <3>;
+		linux,code = <KEY_A>;
+	};
+	key_7 {
+		keypad,row = <1>;
+		keypad,column = <4>;
+		linux,code = <KEY_B>;
+	};
+
+	key_8 {
+		keypad,row = <1>;
+		keypad,column = <5>;
+		linux,code = <KEY_C>;
+	};
+
+	key_9 {
+		keypad,row = <1>;
+		keypad,column = <6>;
+		linux,code = <KEY_D>;
+	};
+
+	key_10 {
+		keypad,row = <1>;
+		keypad,column = <7>;
+		linux,code = <KEY_E>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdhci0 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus1 &sd0_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci1 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus1 &sd1_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci3 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_cd &sd3_bus1 &sd3_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hsotg {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
+
+&fimd {
+	pinctrl-0 = <&lcd_clk &lcd_data24>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	display-timings {
+		native-mode = <&timing0>;
+
+		timing0: timing@0 {
+			/* 800x480@60Hz */
+			clock-frequency = <24373920>;
+			hactive = <800>;
+			vactive = <480>;
+			hfront-porch = <8>;
+			hback-porch = <13>;
+			hsync-len = <3>;
+			vback-porch = <7>;
+			vfront-porch = <5>;
+			vsync-len = <1>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+	};
+};
+
+&pwm {
+	samsung,pwm-outputs = <3>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	audio-codec@1b {
+		compatible = "wlf,wm8580";
+		reg = <0x1b>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+	};
+};
+
+&i2s0 {
+	status = "okay";
+};

arch/arm/boot/dts/s5pv210-torbreck.dts

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Board device tree source for Torbreck board.
+ *
+ * NOTE: This file is completely based on original board file for mach-torbreck
+ * available in Linux 3.15 and intends to provide equivalent level of hardware
+ * support. Due to lack of hardware, _no_ testing has been performed.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "s5pv210.dtsi"
+
+/ {
+	model = "aESOP Torbreck based on S5PV210";
+	compatible = "aesop,torbreck", "samsung,s5pv210";
+
+	chosen {
+		bootargs = "console=ttySAC0,115200n8 root=/dev/mmcblk0p1 rw rootwait ignore_loglevel earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x20000000 0x20000000>;
+	};
+};
+
+&xusbxti {
+	clock-frequency = <24000000>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdhci0 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_cd &sd0_bus1 &sd0_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci1 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_cd &sd1_bus1 &sd1_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus1 &sd2_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhci3 {
+	bus-width = <4>;
+	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_cd &sd3_bus1 &sd3_bus4>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0 {
+	status = "okay";
+};

arch/arm/boot/dts/s5pv210.dtsi

+/*
+ * Samsung's S5PV210 SoC device tree source
+ *
+ * Copyright (c) 2013-2014 Samsung Electronics, Co. Ltd.
+ *
+ * Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
+ * Tomasz Figa <t.figa@samsung.com>
+ *
+ * Samsung's S5PV210 SoC device nodes are listed in this file. S5PV210
+ * based board files can include this file and provide values for board specfic
+ * bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * S5PV210 SoC. As device tree coverage for S5PV210 increases, additional
+ * nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include "skeleton.dtsi"
+#include <dt-bindings/clock/s5pv210.h>
+#include <dt-bindings/clock/s5pv210-audss.h>
+
+/ {
+	aliases {
+		csis0 = &csis0;
+		fimc0 = &fimc0;
+		fimc1 = &fimc1;
+		fimc2 = &fimc2;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2s0 = &i2s0;
+		i2s1 = &i2s1;
+		i2s2 = &i2s2;
+		pinctrl0 = &pinctrl0;
+		spi0 = &spi0;
+		spi1 = &spi1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a8";
+			reg = <0>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		external-clocks {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			xxti: oscillator@0 {
+				compatible = "fixed-clock";
+				reg = <0>;
+				clock-frequency = <0>;
+				clock-output-names = "xxti";
+				#clock-cells = <0>;
+			};
+
+			xusbxti: oscillator@1 {
+				compatible = "fixed-clock";
+				reg = <1>;
+				clock-frequency = <0>;
+				clock-output-names = "xusbxti";
+				#clock-cells = <0>;
+			};
+		};
+
+		onenand: onenand@b0000000 {
+			compatible = "samsung,s5pv210-onenand";
+			reg = <0xb0600000 0x2000>,
+				<0xb0000000 0x20000>,
+				<0xb0040000 0x20000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <31>;
+			clocks = <&clocks CLK_NANDXL>, <&clocks DOUT_FLASH>;
+			clock-names = "bus", "onenand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
+
+		chipid@e0000000 {
+			compatible = "samsung,s5pv210-chipid";
+			reg = <0xe0000000 0x1000>;
+		};
+
+		clocks: clock-controller@e0100000 {
+			compatible = "samsung,s5pv210-clock", "simple-bus";
+			reg = <0xe0100000 0x10000>;
+			clock-names = "xxti", "xusbxti";
+			clocks = <&xxti>, <&xusbxti>;
+			#clock-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pmu_syscon: syscon@e0108000 {
+				compatible = "samsung-s5pv210-pmu", "syscon";
+				reg = <0xe0108000 0x8000>;
+			};
+		};
+
+		pinctrl0: pinctrl@e0200000 {
+			compatible = "samsung,s5pv210-pinctrl";
+			reg = <0xe0200000 0x1000>;
+			interrupt-parent = <&vic0>;
+			interrupts = <30>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos4210-wakeup-eint";
+				interrupts = <16>;
+				interrupt-parent = <&vic0>;
+			};
+		};
+
+		amba {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "arm,amba-bus";
+			ranges;
+
+			pdma0: dma@e0900000 {
+				compatible = "arm,pl330", "arm,primecell";
+				reg = <0xe0900000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <19>;
+				clocks = <&clocks CLK_PDMA0>;
+				clock-names = "apb_pclk";
+				#dma-cells = <1>;
+				#dma-channels = <8>;
+				#dma-requests = <32>;
+			};
+
+			pdma1: dma@e0a00000 {
+				compatible = "arm,pl330", "arm,primecell";
+				reg = <0xe0a00000 0x1000>;
+				interrupt-parent = <&vic0>;
+				interrupts = <20>;
+				clocks = <&clocks CLK_PDMA1>;
+				clock-names = "apb_pclk";
+				#dma-cells = <1>;
+				#dma-channels = <8>;
+				#dma-requests = <32>;
+			};
+		};
+
+		spi0: spi@e1300000 {
+			compatible = "samsung,s5pv210-spi";
+			reg = <0xe1300000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <15>;
+			dmas = <&pdma0 7>, <&pdma0 6>;
+			dma-names = "tx", "rx";
+			clocks = <&clocks SCLK_SPI0>, <&clocks CLK_SPI0>;
+			clock-names = "spi", "spi_busclk0";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_bus>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi1: spi@e1400000 {
+			compatible = "samsung,s5pv210-spi";
+			reg = <0xe1400000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <16>;
+			dmas = <&pdma1 7>, <&pdma1 6>;
+			dma-names = "tx", "rx";
+			clocks = <&clocks SCLK_SPI1>, <&clocks CLK_SPI1>;
+			clock-names = "spi", "spi_busclk0";
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_bus>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		keypad: keypad@e1600000 {
+			compatible = "samsung,s5pv210-keypad";
+			reg = <0xe1600000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <25>;
+			clocks = <&clocks CLK_KEYIF>;
+			clock-names = "keypad";
+			status = "disabled";
+		};
+
+		i2c0: i2c@e1800000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0xe1800000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <14>;
+			clocks = <&clocks CLK_I2C0>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_bus>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@e1a00000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0xe1a00000 0x1000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <19>;
+			clocks = <&clocks CLK_I2C2>;
+			clock-names = "i2c";
+			pinctrl-0 = <&i2c2_bus>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		audio-subsystem {
+			compatible = "samsung,s5pv210-audss", "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clk_audss: clock-controller@eee10000 {
+				compatible = "samsung,s5pv210-audss-clock";
+				reg = <0xeee10000 0x1000>;
+				clock-names = "hclk", "xxti",
+						"fout_epll",
+						"sclk_audio0";
+				clocks = <&clocks DOUT_HCLKP>, <&xxti>,
+						<&clocks FOUT_EPLL>,
+						<&clocks SCLK_AUDIO0>;
+				#clock-cells = <1>;
+			};
+
+			i2s0: i2s@eee30000 {
+				compatible = "samsung,s5pv210-i2s";
+				reg = <0xeee30000 0x1000>;
+				interrupt-parent = <&vic2>;
+				interrupts = <16>;
+				dma-names = "rx", "tx", "tx-sec";
+				dmas = <&pdma1 9>, <&pdma1 10>, <&pdma1 11>;
+				clock-names = "iis",
+						"i2s_opclk0",
+						"i2s_opclk1";
+				clocks = <&clk_audss CLK_I2S>,
+						<&clk_audss CLK_I2S>,
+						<&clk_audss CLK_DOUT_AUD_BUS>;
+				samsung,idma-addr = <0xc0010000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2s0_bus>;
+				#sound-dai-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		i2s1: i2s@e2100000 {
+			compatible = "samsung,s3c6410-i2s";
+			reg = <0xe2100000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <17>;
+			dma-names = "rx", "tx";
+			dmas = <&pdma1 12>, <&pdma1 13>;
+			clock-names = "iis", "i2s_opclk0";
+			clocks = <&clocks CLK_I2S1>, <&clocks SCLK_AUDIO1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2s1_bus>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		i2s2: i2s@e2a00000 {
+			compatible = "samsung,s3c6410-i2s";
+			reg = <0xe2a00000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <18>;
+			dma-names = "rx", "tx";
+			dmas = <&pdma1 14>, <&pdma1 15>;
+			clock-names = "iis", "i2s_opclk0";
+			clocks = <&clocks CLK_I2S2>, <&clocks SCLK_AUDIO2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2s2_bus>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		pwm: pwm@e2500000 {
+			compatible = "samsung,s5pc100-pwm";
+			reg = <0xe2500000 0x1000>;
+			interrupt-parent = <&vic0>;
+			interrupts = <21>, <22>, <23>, <24>, <25>;
+			clock-names = "timers";
+			clocks = <&clocks CLK_PWM>;
+			#pwm-cells = <3>;
+		};
+
+		watchdog: watchdog@e2700000 {
+			compatible = "samsung,s3c2410-wdt";
+			reg = <0xe2700000 0x1000>;
+			interrupt-parent = <&vic0>;
+			interrupts = <26>;
+			clock-names = "watchdog";
+			clocks = <&clocks CLK_WDT>;
+		};
+
+		rtc: rtc@e2800000 {
+			compatible = "samsung,s3c6410-rtc";
+			reg = <0xe2800000 0x100>;
+			interrupt-parent = <&vic0>;
+			interrupts = <28>, <29>;
+			clocks = <&clocks CLK_RTC>;
+			clock-names = "rtc";
+			status = "disabled";
+		};
+
+		uart0: serial@e2900000 {
+			compatible = "samsung,s5pv210-uart";
+			reg = <0xe2900000 0x400>;
+			interrupt-parent = <&vic1>;
+			interrupts = <10>;
+			clock-names = "uart", "clk_uart_baud0",
+					"clk_uart_baud1";
+			clocks = <&clocks CLK_UART0>, <&clocks CLK_UART0>,
+					<&clocks SCLK_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@e2900400 {
+			compatible = "samsung,s5pv210-uart";
+			reg = <0xe2900400 0x400>;
+			interrupt-parent = <&vic1>;
+			interrupts = <11>;
+			clock-names = "uart", "clk_uart_baud0",
+					"clk_uart_baud1";
+			clocks = <&clocks CLK_UART1>, <&clocks CLK_UART1>,
+					<&clocks SCLK_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@e2900800 {
+			compatible = "samsung,s5pv210-uart";
+			reg = <0xe2900800 0x400>;
+			interrupt-parent = <&vic1>;
+			interrupts = <12>;
+			clock-names = "uart", "clk_uart_baud0",
+					"clk_uart_baud1";
+			clocks = <&clocks CLK_UART2>, <&clocks CLK_UART2>,
+					<&clocks SCLK_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@e2900c00 {
+			compatible = "samsung,s5pv210-uart";
+			reg = <0xe2900c00 0x400>;
+			interrupt-parent = <&vic1>;
+			interrupts = <13>;
+			clock-names = "uart", "clk_uart_baud0",
+					"clk_uart_baud1";
+			clocks = <&clocks CLK_UART3>, <&clocks CLK_UART3>,
+					<&clocks SCLK_UART3>;
+			status = "disabled";
+		};
+
+		sdhci0: sdhci@eb000000 {
+			compatible = "samsung,s3c6410-sdhci";
+			reg = <0xeb000000 0x100000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <26>;
+			clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+			clocks = <&clocks CLK_HSMMC0>, <&clocks CLK_HSMMC0>,
+					<&clocks SCLK_MMC0>;
+			status = "disabled";
+		};
+
+		sdhci1: sdhci@eb100000 {
+			compatible = "samsung,s3c6410-sdhci";
+			reg = <0xeb100000 0x100000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <27>;
+			clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+			clocks = <&clocks CLK_HSMMC1>, <&clocks CLK_HSMMC1>,
+					<&clocks SCLK_MMC1>;
+			status = "disabled";
+		};
+
+		sdhci2: sdhci@eb200000 {
+			compatible = "samsung,s3c6410-sdhci";
+			reg = <0xeb200000 0x100000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <28>;
+			clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.2";
+			clocks = <&clocks CLK_HSMMC2>, <&clocks CLK_HSMMC2>,
+					<&clocks SCLK_MMC2>;
+			status = "disabled";
+		};
+
+		sdhci3: sdhci@eb300000 {
+			compatible = "samsung,s3c6410-sdhci";
+			reg = <0xeb300000 0x100000>;
+			interrupt-parent = <&vic3>;
+			interrupts = <2>;
+			clock-names = "hsmmc", "mmc_busclk.0", "mmc_busclk.3";
+			clocks = <&clocks CLK_HSMMC3>, <&clocks CLK_HSMMC3>,
+					<&clocks SCLK_MMC3>;
+			status = "disabled";
+		};
+
+		hsotg: hsotg@ec000000 {
+			compatible = "samsung,s3c6400-hsotg";
+			reg = <0xec000000 0x20000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <24>;
+			clocks = <&clocks CLK_USB_OTG>;
+			clock-names = "otg";
+			phy-names = "usb2-phy";
+			phys = <&usbphy 0>;
+			status = "disabled";
+		};
+
+		usbphy: usbphy@ec100000 {
+			compatible = "samsung,s5pv210-usb2-phy";
+			reg = <0xec100000 0x100>;
+			samsung,pmureg-phandle = <&pmu_syscon>;
+			clocks = <&clocks CLK_USB_OTG>, <&xusbxti>;
+			clock-names = "phy", "ref";
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ehci: ehci@ec200000 {
+			compatible = "samsung,exynos4210-ehci";
+			reg = <0xec200000 0x100>;
+			interrupts = <23>;
+			interrupt-parent = <&vic1>;
+			clocks = <&clocks CLK_USB_HOST>;
+			clock-names = "usbhost";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			port@0 {
+				reg = <0>;
+				phys = <&usbphy 1>;
+			};
+		};
+
+		ohci: ohci@ec300000 {
+			compatible = "samsung,exynos4210-ohci";
+			reg = <0xec300000 0x100>;
+			interrupts = <23>;
+			clocks = <&clocks CLK_USB_HOST>;
+			clock-names = "usbhost";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			port@0 {
+				reg = <0>;
+				phys = <&usbphy 1>;
+			};
+		};
+
+		mfc: codec@f1700000 {
+			compatible = "samsung,mfc-v5";
+			reg = <0xf1700000 0x10000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <14>;
+			clocks = <&clocks DOUT_MFC>, <&clocks CLK_MFC>;
+			clock-names = "sclk_mfc", "mfc";
+		};
+
+		vic0: interrupt-controller@f2000000 {
+			compatible = "arm,pl192-vic";
+			interrupt-controller;
+			reg = <0xf2000000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		vic1: interrupt-controller@f2100000 {
+			compatible = "arm,pl192-vic";
+			interrupt-controller;
+			reg = <0xf2100000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		vic2: interrupt-controller@f2200000 {
+			compatible = "arm,pl192-vic";
+			interrupt-controller;
+			reg = <0xf2200000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		vic3: interrupt-controller@f2300000 {
+			compatible = "arm,pl192-vic";
+			interrupt-controller;
+			reg = <0xf2300000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		fimd: fimd@f8000000 {
+			compatible = "samsung,exynos4210-fimd";
+			interrupt-parent = <&vic2>;
+			reg = <0xf8000000 0x20000>;
+			interrupt-names = "fifo", "vsync", "lcd_sys";
+			interrupts = <0>, <1>, <2>;
+			clocks = <&clocks SCLK_FIMD>, <&clocks CLK_FIMD>;
+			clock-names = "sclk_fimd", "fimd";
+			status = "disabled";
+		};
+
+		g2d: g2d@fa000000 {
+			compatible = "samsung,s5pv210-g2d";
+			reg = <0xfa000000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <9>;
+			clocks = <&clocks DOUT_G2D>, <&clocks CLK_G2D>;
+			clock-names = "sclk_fimg2d", "fimg2d";
+		};
+
+		mdma1: mdma@fa200000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0xfa200000 0x1000>;
+			interrupt-parent = <&vic0>;
+			interrupts = <18>;
+			clocks = <&clocks CLK_MDMA>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+			#dma-channels = <8>;
+			#dma-requests = <1>;
+		};
+
+		i2c1: i2c@fab00000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0xfab00000 0x1000>;
+			interrupt-parent = <&vic2>;
+			interrupts = <13>;
+			clocks = <&clocks CLK_I2C1>;
+			clock-names = "i2c";
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_bus>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		camera: camera {
+			compatible = "samsung,fimc", "simple-bus";
+			pinctrl-names = "default";
+			pinctrl-0 = <>;
+			clocks = <&clocks SCLK_CAM0>, <&clocks SCLK_CAM1>;
+			clock-names = "sclk_cam0", "sclk_cam1";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clock_cam: clock-controller {
+				#clock-cells = <1>;
+			};
+
+			csis0: csis@fa600000 {
+				compatible = "samsung,s5pv210-csis";
+				reg = <0xfa600000 0x4000>;
+				interrupt-parent = <&vic2>;
+				interrupts = <29>;
+				clocks = <&clocks CLK_CSIS>,
+						<&clocks SCLK_CSIS>;
+				clock-names = "clk_csis",
+						"sclk_csis";
+				bus-width = <4>;
+				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			fimc0: fimc@fb200000 {
+				compatible = "samsung,s5pv210-fimc";
+				reg = <0xfb200000 0x1000>;
+				interrupts = <5>;
+				interrupt-parent = <&vic2>;
+				clocks = <&clocks CLK_FIMC0>,
+						<&clocks SCLK_FIMC0>;
+				clock-names = "fimc",
+						"sclk_fimc";
+				samsung,pix-limits = <4224 8192 1920 4224>;
+				samsung,mainscaler-ext;
+				samsung,cam-if;
+			};
+
+			fimc1: fimc@fb300000 {
+				compatible = "samsung,s5pv210-fimc";
+				reg = <0xfb300000 0x1000>;
+				interrupt-parent = <&vic2>;
+				interrupts = <6>;
+				clocks = <&clocks CLK_FIMC1>,
+						<&clocks SCLK_FIMC1>;
+				clock-names = "fimc",
+						"sclk_fimc";
+				samsung,pix-limits = <4224 8192 1920 4224>;
+				samsung,mainscaler-ext;
+				samsung,cam-if;
+			};
+
+			fimc2: fimc@fb400000 {
+				compatible = "samsung,s5pv210-fimc";
+				reg = <0xfb400000 0x1000>;
+				interrupt-parent = <&vic2>;
+				interrupts = <7>;
+				clocks = <&clocks CLK_FIMC2>,
+						<&clocks SCLK_FIMC2>;
+				clock-names = "fimc",
+						"sclk_fimc";
+				samsung,pix-limits = <4224 8192 1920 4224>;
+				samsung,mainscaler-ext;
+				samsung,lcd-wb;
+			};
+		};
+	};
+};
+
+#include "s5pv210-pinctrl.dtsi"

arch/arm/mach-s5pv210/include/mach/debug-macro.S → arch/arm/include/debug/s5pv210.S

-/* linux/arch/arm/mach-s5pv210/include/mach/debug-macro.S
- *
- * Copyright (c) 2010 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com/
- *
- * Based on arch/arm/mach-s3c6400/include/mach/debug-macro.S
+/*
+ * Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
@@ -12,8 +9,9 @@
 
 /* pull in the relevant register and map files. */
 
-#include <linux/serial_s3c.h>
-#include <mach/map.h>
+#define S3C_ADDR_BASE   0xF6000000
+#define S3C_VA_UART	S3C_ADDR_BASE + 0x01000000
+#define S5PV210_PA_UART	0xe2900000
 
 	/* note, for the boot process to work we have to keep the UART
 	 * virtual address aligned to an 1MiB boundary for the L1
@@ -22,8 +20,8 @@
 	 */
 
 	.macro addruart, rp, rv, tmp
-		ldr	\rp, = S3C_PA_UART
-		ldr	\rv, = S3C_VA_UART
+		ldr	\rp, =S5PV210_PA_UART
+		ldr	\rv, =S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0
 		add	\rp, \rp, #(0x400 * CONFIG_DEBUG_S3C_UART)
 		add	\rv, \rv, #(0x400 * CONFIG_DEBUG_S3C_UART)
@@ -33,9 +31,4 @@
 #define fifo_full fifo_full_s5pv210
 #define fifo_level fifo_level_s5pv210
 
-/* include the reset of the code which will do the work, we're only
- * compiling for a single cpu processor type so the default of s3c2440
- * will be fine with us.
- */
-
 #include <debug/samsung.S>

arch/arm/mach-exynos/pm.c

@@ -28,7 +28,6 @@
 #include <asm/suspend.h>
 
 #include <plat/pm-common.h>
-#include <plat/pll.h>
 #include <plat/regs-srom.h>
 
 #include <mach/map.h>

arch/arm/mach-s3c24xx/common.c

@@ -49,9 +49,7 @@
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/clock.h>
 #include <plat/cpu-freq.h>
-#include <plat/pll.h>
 #include <plat/pwm-core.h>
 #include <plat/watchdog-reset.h>
 

arch/arm/mach-s3c24xx/iotiming-s3c2412.c

@@ -29,7 +29,6 @@
 
 #include <plat/cpu.h>
 #include <plat/cpu-freq-core.h>
-#include <plat/clock.h>
 
 #include <mach/s3c2412.h>
 

arch/arm/mach-s3c24xx/mach-h1940.c

@@ -60,7 +60,6 @@
 #include <plat/cpu.h>
 #include <plat/devs.h>
 #include <plat/gpio-cfg.h>
-#include <plat/pll.h>
 #include <plat/pm.h>
 #include <plat/samsung-time.h>
 
@@ -73,6 +72,10 @@
 
 #define H1940_LATCH_BIT(x)	(1 << ((x) + 16 - S3C_GPIO_END))
 
+#define S3C24XX_PLL_MDIV_SHIFT         (12)
+#define S3C24XX_PLL_PDIV_SHIFT         (4)
+#define S3C24XX_PLL_SDIV_SHIFT         (0)
+
 static struct map_desc h1940_iodesc[] __initdata = {
 	[0] = {
 		.virtual	= (unsigned long)H1940_LATCH,

arch/arm/mach-s3c24xx/mach-jive.c

@@ -48,7 +48,6 @@
 #include <linux/mtd/partitions.h>
 
 #include <plat/gpio-cfg.h>
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/pm.h>

arch/arm/mach-s3c24xx/mach-smdk2413.c

@@ -43,7 +43,6 @@
 #include <mach/gpio-samsung.h>
 #include <mach/fb.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/samsung-time.h>

arch/arm/mach-s3c24xx/mach-smdk2416.c

@@ -44,7 +44,6 @@
 #include <linux/platform_data/i2c-s3c2410.h>
 
 #include <plat/gpio-cfg.h>
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>

arch/arm/mach-s3c24xx/mach-smdk2443.c

@@ -38,7 +38,6 @@
 #include <mach/fb.h>
 #include <linux/platform_data/i2c-s3c2410.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/samsung-time.h>

arch/arm/mach-s3c24xx/mach-vstms.c

@@ -42,7 +42,6 @@
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/samsung-time.h>

arch/arm/mach-s3c24xx/s3c2410.c

@@ -41,8 +41,6 @@
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/clock.h>
-#include <plat/pll.h>
 #include <plat/pm.h>
 #include <plat/watchdog-reset.h>
 
@@ -83,10 +81,6 @@ void __init s3c2410_map_io(void)
 	iotable_init(s3c2410_iodesc, ARRAY_SIZE(s3c2410_iodesc));
 }
 
-void __init_or_cpufreq s3c2410_setup_clocks(void)
-{
-}
-
 struct bus_type s3c2410_subsys = {
 	.name = "s3c2410-core",
 	.dev_name = "s3c2410-core",

arch/arm/mach-s3c24xx/s3c2412.c

@@ -37,12 +37,10 @@
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
-#include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/cpu-freq.h>
 #include <plat/devs.h>
 #include <plat/nand-core.h>
-#include <plat/pll.h>
 #include <plat/pm.h>
 #include <plat/regs-spi.h>
 
@@ -171,10 +169,6 @@ void __init s3c2412_map_io(void)
 	iotable_init(s3c2412_iodesc, ARRAY_SIZE(s3c2412_iodesc));
 }
 
-void __init_or_cpufreq s3c2412_setup_clocks(void)
-{
-}
-
 /* need to register the subsystem before we actually register the device, and
  * we also need to ensure that it has been initialised before any of the
  * drivers even try to use it (even if not on an s3c2412 based system)

arch/arm/mach-s3c24xx/s3c2442.c

@@ -43,7 +43,6 @@
 
 #include <mach/regs-clock.h>
 
-#include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/pm.h>
 

arch/arm/mach-s3c24xx/s3c244x.c

@@ -38,11 +38,9 @@
 #include <mach/regs-clock.h>
 #include <mach/regs-gpio.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/pm.h>
-#include <plat/pll.h>
 #include <plat/nand-core.h>
 #include <plat/watchdog-reset.h>
 
@@ -78,10 +76,6 @@ void __init s3c244x_map_io(void)
 	s3c2410_device_dclk.name = "s3c2440-dclk";
 }
 
-void __init_or_cpufreq s3c244x_setup_clocks(void)
-{
-}
-
 /* Since the S3C2442 and S3C2440 share items, put both subsystems here */
 
 struct bus_type s3c2440_subsys = {

arch/arm/mach-s3c64xx/mach-anw6410.c

@@ -45,7 +45,6 @@
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <plat/fb.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <mach/regs-gpio.h>

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -58,7 +58,6 @@
 #include <linux/platform_data/spi-s3c64xx.h>
 
 #include <plat/keypad.h>
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/adc.h>

arch/arm/mach-s3c64xx/mach-hmt.c

@@ -39,7 +39,6 @@
 #include <plat/fb.h>
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/samsung-time.h>

arch/arm/mach-s3c64xx/mach-ncp.c

@@ -40,7 +40,6 @@
 #include <linux/platform_data/i2c-s3c2410.h>
 #include <plat/fb.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/samsung-time.h>

arch/arm/mach-s3c64xx/mach-smartq.c

@@ -28,7 +28,6 @@
 #include <mach/regs-gpio.h>
 #include <mach/gpio-samsung.h>
 
-#include <plat/clock.h>
 #include <plat/cpu.h>
 #include <plat/devs.h>
 #include <linux/platform_data/i2c-s3c2410.h>

arch/arm/mach-s3c64xx/mach-smdk6400.c

@@ -30,7 +30,6 @@
 #include <mach/hardware.h>
 #include <mach/map.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <linux/platform_data/i2c-s3c2410.h>

arch/arm/mach-s3c64xx/mach-smdk6410.c

@@ -63,7 +63,6 @@
 #include <plat/fb.h>
 #include <plat/gpio-cfg.h>
 
-#include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
 #include <plat/adc.h>

arch/arm/mach-s3c64xx/s3c6400.c

@@ -39,7 +39,6 @@
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/clock.h>
 #include <plat/sdhci.h>
 #include <plat/iic-core.h>
 #include <plat/onenand-core.h>

arch/arm/mach-s3c64xx/s3c6410.c

@@ -40,7 +40,6 @@
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/clock.h>
 #include <plat/sdhci.h>
 #include <plat/ata-core.h>
 #include <plat/adc-core.h>

arch/arm/mach-s5pv210/Kconfig

@@ -7,193 +7,28 @@
 
 # Configuration options for the S5PV210/S5PC110
 
+config ARCH_S5PV210
+	bool "Samsung S5PV210/S5PC110" if ARCH_MULTI_V7
+	select ARCH_HAS_HOLES_MEMORYMODEL
+	select ARCH_REQUIRE_GPIOLIB
+	select ARM_VIC
+	select CLKSRC_SAMSUNG_PWM
+	select COMMON_CLK_SAMSUNG
+	select HAVE_S3C2410_I2C if I2C
+	select HAVE_S3C2410_WATCHDOG if WATCHDOG
+	select HAVE_S3C_RTC if RTC_CLASS
+	select PINCTRL
+	select PINCTRL_EXYNOS
+	help
+	  Samsung S5PV210/S5PC110 series based systems
+
 if ARCH_S5PV210
 
 config CPU_S5PV210
-	bool
+	def_bool y
 	select ARM_AMBA
 	select PL330_DMA if DMADEVICES
-	select S5P_EXT_INT
-	select S5P_PM if PM
-	select S5P_SLEEP if PM
 	help
 	  Enable S5PV210 CPU support
 
-config S5PV210_SETUP_I2C1
-	bool
-	help
-	  Common setup code for i2c bus 1.
-
-config S5PV210_SETUP_I2C2
-	bool
-	help
-	  Common setup code for i2c bus 2.
-
-config S5PV210_SETUP_IDE
-	bool
-	help
-	  Common setup code for S5PV210 IDE GPIO configurations
-
-config S5PV210_SETUP_FB_24BPP
-	bool
-	help
-          Common setup code for S5PV210 with an 24bpp RGB display helper.
-
-config S5PV210_SETUP_KEYPAD
-	bool
-	help
-	  Common setup code for keypad.
-
-config S5PV210_SETUP_SDHCI
-        bool
-        select S5PV210_SETUP_SDHCI_GPIO
-        help
-          Internal helper functions for S5PV210 based SDHCI systems
-
-config S5PV210_SETUP_SDHCI_GPIO
-	bool
-	help
-	  Common setup code for SDHCI gpio.
-
-config S5PV210_SETUP_FIMC
-	bool
-	help
-	  Common setup code for the camera interfaces.
-
-config S5PV210_SETUP_SPI
-	bool
-	help
-	  Common setup code for SPI GPIO configurations.
-
-config S5PV210_SETUP_USB_PHY
-	bool
-	help
-	  Common setup code for USB PHY controller
-
-menu "S5PC110 Machines"
-
-config MACH_AQUILA
-	bool "Aquila"
-	select CPU_S5PV210
-	select S3C_DEV_FB
-	select S3C_DEV_HSMMC
-	select S3C_DEV_HSMMC1
-	select S3C_DEV_HSMMC2
-	select S5PV210_SETUP_FB_24BPP
-	select S5PV210_SETUP_SDHCI
-	select S5PV210_SETUP_USB_PHY
-	select S5P_DEV_FIMC0
-	select S5P_DEV_FIMC1
-	select S5P_DEV_FIMC2
-	select S5P_DEV_ONENAND
-	help
-	  Machine support for the Samsung Aquila target based on S5PC110 SoC
-
-config MACH_GONI
-	bool "GONI"
-	select CPU_S5PV210
-	select S3C_DEV_FB
-	select S3C_DEV_HSMMC
-	select S3C_DEV_HSMMC1
-	select S3C_DEV_HSMMC2
-	select S3C_DEV_I2C1
-	select S3C_DEV_I2C2
-	select S3C_DEV_USB_HSOTG
-	select S5PV210_SETUP_FB_24BPP
-	select S5PV210_SETUP_FIMC
-	select S5PV210_SETUP_I2C1
-	select S5PV210_SETUP_I2C2
-	select S5PV210_SETUP_KEYPAD
-	select S5PV210_SETUP_SDHCI
-	select S5PV210_SETUP_USB_PHY
-	select S5P_DEV_FIMC0
-	select S5P_DEV_FIMC1
-	select S5P_DEV_FIMC2
-	select S5P_DEV_MFC
-	select S5P_DEV_ONENAND
-	select S5P_DEV_TV
-	select S5P_GPIO_INT
-	select SAMSUNG_DEV_KEYPAD
-	help
-	  Machine support for Samsung GONI board
-	  S5PC110(MCP) is one of package option of S5PV210
-
-config MACH_SMDKC110
-	bool "SMDKC110"
-	select CPU_S5PV210
-	select S3C_DEV_I2C1
-	select S3C_DEV_I2C2
-	select S3C_DEV_RTC
-	select S3C_DEV_WDT
-	select S5PV210_SETUP_I2C1
-	select S5PV210_SETUP_I2C2
-	select S5PV210_SETUP_IDE
-	select S5P_DEV_FIMC0
-	select S5P_DEV_FIMC1
-	select S5P_DEV_FIMC2
-	select S5P_DEV_MFC
-	select SAMSUNG_DEV_IDE
-	help
-	  Machine support for Samsung SMDKC110
-	  S5PC110(MCP) is one of package option of S5PV210
-
-endmenu
-
-menu "S5PV210 Machines"
-
-config MACH_SMDKV210
-	bool "SMDKV210"
-	select CPU_S5PV210
-	select S3C_DEV_FB
-	select S3C_DEV_HSMMC
-	select S3C_DEV_HSMMC1
-	select S3C_DEV_HSMMC2
-	select S3C_DEV_HSMMC3
-	select S3C_DEV_I2C1
-	select S3C_DEV_I2C2
-	select S3C_DEV_RTC
-	select S3C_DEV_USB_HSOTG
-	select S3C_DEV_WDT
-	select S5PV210_SETUP_FB_24BPP
-	select S5PV210_SETUP_I2C1
-	select S5PV210_SETUP_I2C2
-	select S5PV210_SETUP_IDE
-	select S5PV210_SETUP_KEYPAD
-	select S5PV210_SETUP_SDHCI
-	select S5PV210_SETUP_USB_PHY
-	select S5P_DEV_FIMC0
-	select S5P_DEV_FIMC1
-	select S5P_DEV_FIMC2
-	select S5P_DEV_JPEG
-	select S5P_DEV_MFC
-	select SAMSUNG_DEV_ADC
-	select SAMSUNG_DEV_BACKLIGHT
-	select SAMSUNG_DEV_IDE
-	select SAMSUNG_DEV_KEYPAD
-	select SAMSUNG_DEV_PWM
-	select SAMSUNG_DEV_TS
-	help
-	  Machine support for Samsung SMDKV210
-
-config MACH_TORBRECK
-	bool "Torbreck"
-	select ARCH_SPARSEMEM_ENABLE
-	select CPU_S5PV210
-	select S3C_DEV_HSMMC
-	select S3C_DEV_HSMMC1
-	select S3C_DEV_HSMMC2
-	select S3C_DEV_HSMMC3
-	select S3C_DEV_I2C1
-	select S3C_DEV_I2C2
-	select S3C_DEV_RTC
-	select S3C_DEV_WDT
-	select S5PV210_SETUP_I2C1
-	select S5PV210_SETUP_I2C2
-	select S5PV210_SETUP_SDHCI
-	select SAMSUNG_DEV_IDE
-	help
-	  Machine support for aESOP Torbreck
-
-endmenu
-
 endif

arch/arm/mach-s5pv210/Makefile

@@ -5,6 +5,8 @@
 #
 # Licensed under GPLv2
 
+ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/$(src)/include -I$(srctree)/arch/arm/plat-samsung/include
+
 obj-y				:=
 obj-m				:=
 obj-n				:=
@@ -12,31 +14,8 @@ obj-				:=
 
 # Core
 
-obj-y				+= common.o clock.o
-
-obj-$(CONFIG_PM)		+= pm.o
-
-obj-y				+= dma.o
+obj-$(CONFIG_PM_SLEEP)		+= pm.o sleep.o
 
 # machine support
 
-obj-$(CONFIG_MACH_AQUILA)	+= mach-aquila.o
-obj-$(CONFIG_MACH_GONI)		+= mach-goni.o
-obj-$(CONFIG_MACH_SMDKC110)	+= mach-smdkc110.o
-obj-$(CONFIG_MACH_SMDKV210)	+= mach-smdkv210.o
-obj-$(CONFIG_MACH_TORBRECK)	+= mach-torbreck.o
-
-# device support
-
-obj-y				+= dev-audio.o
-
-obj-y					+= setup-i2c0.o
-obj-$(CONFIG_S5PV210_SETUP_FB_24BPP)	+= setup-fb-24bpp.o
-obj-$(CONFIG_S5PV210_SETUP_FIMC)	+= setup-fimc.o
-obj-$(CONFIG_S5PV210_SETUP_I2C1)	+= setup-i2c1.o
-obj-$(CONFIG_S5PV210_SETUP_I2C2)	+= setup-i2c2.o
-obj-$(CONFIG_S5PV210_SETUP_IDE)		+= setup-ide.o
-obj-$(CONFIG_S5PV210_SETUP_KEYPAD)	+= setup-keypad.o
-obj-$(CONFIG_S5PV210_SETUP_SDHCI_GPIO)	+= setup-sdhci-gpio.o
-obj-$(CONFIG_S5PV210_SETUP_SPI)		+= setup-spi.o
-obj-$(CONFIG_S5PV210_SETUP_USB_PHY) += setup-usb-phy.o
+obj-y				+= s5pv210.o

arch/arm/mach-s5pv210/Makefile.boot

-   zreladdr-y	+= 0x20008000
-params_phys-y	:= 0x20000100

arch/arm/mach-s5pv210/common.h

@@ -12,19 +12,12 @@
 #ifndef __ARCH_ARM_MACH_S5PV210_COMMON_H
 #define __ARCH_ARM_MACH_S5PV210_COMMON_H
 
-#include <linux/reboot.h>
-
-void s5pv210_init_io(struct map_desc *mach_desc, int size);
-void s5pv210_init_irq(void);
-
-void s5pv210_register_clocks(void);
-void s5pv210_setup_clocks(void);
-
-void s5pv210_restart(enum reboot_mode mode, const char *cmd);
-
-extern  int s5pv210_init(void);
-extern void s5pv210_map_io(void);
-extern void s5pv210_init_clocks(int xtal);
-extern void s5pv210_init_uarts(struct s3c2410_uartcfg *cfg, int no);
+#ifdef CONFIG_PM_SLEEP
+u32 exynos_get_eint_wake_mask(void);
+void s5pv210_cpu_resume(void);
+void s5pv210_pm_init(void);
+#else
+static inline void s5pv210_pm_init(void) {}
+#endif
 
 #endif /* __ARCH_ARM_MACH_S5PV210_COMMON_H */

arch/arm/mach-s5pv210/dma.c

-/* linux/arch/arm/mach-s5pv210/dma.c
- *
- * Copyright (c) 2011 Samsung Electronics Co., Ltd.
- *		http://www.samsung.com
- *
- * Copyright (C) 2010 Samsung Electronics Co. Ltd.
- *	Jaswinder Singh <jassi.brar@samsung.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/pl330.h>
-
-#include <asm/irq.h>
-#include <plat/devs.h>
-#include <plat/irqs.h>
-
-#include <mach/map.h>
-#include <mach/irqs.h>
-#include <mach/dma.h>
-
-static u8 pdma0_peri[] = {
-	DMACH_UART0_RX,
-	DMACH_UART0_TX,
-	DMACH_UART1_RX,
-	DMACH_UART1_TX,
-	DMACH_UART2_RX,
-	DMACH_UART2_TX,
-	DMACH_UART3_RX,
-	DMACH_UART3_TX,
-	DMACH_MAX,
-	DMACH_I2S0_RX,
-	DMACH_I2S0_TX,
-	DMACH_I2S0S_TX,
-	DMACH_I2S1_RX,
-	DMACH_I2S1_TX,
-	DMACH_MAX,
-	DMACH_MAX,
-	DMACH_SPI0_RX,
-	DMACH_SPI0_TX,
-	DMACH_SPI1_RX,
-	DMACH_SPI1_TX,
-	DMACH_MAX,
-	DMACH_MAX,
-	DMACH_AC97_MICIN,
-	DMACH_AC97_PCMIN,
-	DMACH_AC97_PCMOUT,
-	DMACH_MAX,
-	DMACH_PWM,
-	DMACH_SPDIF,
-};
-
-static struct dma_pl330_platdata s5pv210_pdma0_pdata = {
-	.nr_valid_peri = ARRAY_SIZE(pdma0_peri),
-	.peri_id = pdma0_peri,
-};
-
-static AMBA_AHB_DEVICE(s5pv210_pdma0, "dma-pl330.0", 0x00041330,
-	S5PV210_PA_PDMA0, {IRQ_PDMA0}, &s5pv210_pdma0_pdata);
-
-static u8 pdma1_peri[] = {
-	DMACH_UART0_RX,
-	DMACH_UART0_TX,
-	DMACH_UART1_RX,
-	DMACH_UART1_TX,
-	DMACH_UART2_RX,
-	DMACH_UART2_TX,
-	DMACH_UART3_RX,
-	DMACH_UART3_TX,
-	DMACH_MAX,
-	DMACH_I2S0_RX,
-	DMACH_I2S0_TX,
-	DMACH_I2S0S_TX,
-	DMACH_I2S1_RX,
-	DMACH_I2S1_TX,
-	DMACH_I2S2_RX,
-	DMACH_I2S2_TX,
-	DMACH_SPI0_RX,
-	DMACH_SPI0_TX,
-	DMACH_SPI1_RX,
-	DMACH_SPI1_TX,
-	DMACH_MAX,
-	DMACH_MAX,
-	DMACH_PCM0_RX,
-	DMACH_PCM0_TX,
-	DMACH_PCM1_RX,
-	DMACH_PCM1_TX,
-	DMACH_MSM_REQ0,
-	DMACH_MSM_REQ1,
-	DMACH_MSM_REQ2,
-	DMACH_MSM_REQ3,
-	DMACH_PCM2_RX,
-	DMACH_PCM2_TX,
-};
-
-static struct dma_pl330_platdata s5pv210_pdma1_pdata = {
-	.nr_valid_peri = ARRAY_SIZE(pdma1_peri),
-	.peri_id = pdma1_peri,
-};
-
-static AMBA_AHB_DEVICE(s5pv210_pdma1, "dma-pl330.1", 0x00041330,
-	S5PV210_PA_PDMA1, {IRQ_PDMA1}, &s5pv210_pdma1_pdata);
-
-static int __init s5pv210_dma_init(void)
-{
-	dma_cap_set(DMA_SLAVE, s5pv210_pdma0_pdata.cap_mask);
-	dma_cap_set(DMA_CYCLIC, s5pv210_pdma0_pdata.cap_mask);
-	amba_device_register(&s5pv210_pdma0_device, &iomem_resource);
-
-	dma_cap_set(DMA_SLAVE, s5pv210_pdma1_pdata.cap_mask);
-	dma_cap_set(DMA_CYCLIC, s5pv210_pdma1_pdata.cap_mask);
-	amba_device_register(&s5pv210_pdma1_device, &iomem_resource);
-
-	return 0;
-}
-arch_initcall(s5pv210_dma_init);

arch/arm/plat-samsung/init.c

@@ -30,7 +30,6 @@
 
 #include <plat/cpu.h>
 #include <plat/devs.h>
-#include <plat/clock.h>
 
 static struct cpu_table *cpu;