MIPS: Netlogic: Add built-in dts for XLP5xx boards

Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8896/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/boot/dts/netlogic/Makefile

@@ -2,6 +2,7 @@ dtb-$(CONFIG_DT_XLP_EVP)	+= xlp_evp.dtb
 dtb-$(CONFIG_DT_XLP_SVP)	+= xlp_svp.dtb
 dtb-$(CONFIG_DT_XLP_FVP)	+= xlp_fvp.dtb
 dtb-$(CONFIG_DT_XLP_GVP)	+= xlp_gvp.dtb
+dtb-$(CONFIG_DT_XLP_RVP)	+= xlp_rvp.dtb
 
 obj-y				+= $(patsubst %.dtb, %.dtb.o, $(dtb-y))
 

arch/mips/boot/dts/netlogic/xlp_rvp.dts

+/*
+ * XLP5XX Device Tree Source for RVP boards
+ */
+
+/dts-v1/;
+/ {
+	model = "netlogic,XLP-RVP";
+	compatible = "netlogic,xlp";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges = <0 0  0 0x18000000  0x04000000   // PCIe CFG
+			  1 0  0 0x16000000  0x02000000>; // GBU chipselects
+
+		serial0: serial@30000 {
+			device_type = "serial";
+			compatible = "ns16550";
+			reg = <0 0x112100 0xa00>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clock-frequency = <125000000>;
+			interrupt-parent = <&pic>;
+			interrupts = <17>;
+		};
+		pic: pic@110000 {
+			compatible = "netlogic,xlp-pic";
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			reg = <0 0x110000 0x200>;
+			interrupt-controller;
+		};
+
+		nor_flash@1,0 {
+			compatible = "cfi-flash";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			reg = <1 0 0x1000000>;
+
+			partition@0 {
+				label = "x-loader";
+				reg = <0x0 0x100000>; /* 1M */
+				read-only;
+			};
+
+			partition@100000 {
+				label = "u-boot";
+				reg = <0x100000 0x100000>; /* 1M */
+			};
+
+			partition@200000 {
+				label = "kernel";
+				reg = <0x200000 0x500000>; /* 5M */
+			};
+
+			partition@700000 {
+				label = "rootfs";
+				reg = <0x700000 0x800000>; /* 8M */
+			};
+
+			partition@f00000 {
+				label = "env";
+				reg = <0xf00000 0x100000>; /* 1M */
+				read-only;
+			};
+		};
+
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 rdinit=/sbin/init";
+	};
+};

arch/mips/netlogic/Kconfig

@@ -41,6 +41,15 @@ config DT_XLP_GVP
 	  pointer to the kernel.  The corresponding DTS file is at
 	  arch/mips/netlogic/dts/xlp_gvp.dts
 
+config DT_XLP_RVP
+	bool "Built-in device tree for XLP RVP boards"
+	default y
+	help
+	  Add an FDT blob for XLP RVP board into the kernel.
+	  This DTB will be used if the firmware does not pass in a DTB
+	  pointer to the kernel.  The corresponding DTS file is at
+	  arch/mips/netlogic/dts/xlp_rvp.dts
+
 config NLM_MULTINODE
 	bool "Support for multi-chip boards"
 	depends on NLM_XLP_BOARD

arch/mips/netlogic/xlp/dt.c

@@ -41,17 +41,21 @@
 
 #include <asm/prom.h>
 
-extern u32 __dtb_xlp_evp_begin[], __dtb_xlp_svp_begin[],
-	__dtb_xlp_fvp_begin[], __dtb_xlp_gvp_begin[];
+extern u32 __dtb_xlp_evp_begin[], __dtb_xlp_svp_begin[], __dtb_xlp_fvp_begin[],
+	__dtb_xlp_gvp_begin[], __dtb_xlp_rvp_begin[];
 static void *xlp_fdt_blob;
 
 void __init *xlp_dt_init(void *fdtp)
 {
 	if (!fdtp) {
 		switch (current_cpu_data.processor_id & PRID_IMP_MASK) {
+#ifdef CONFIG_DT_XLP_RVP
+		case PRID_IMP_NETLOGIC_XLP5XX:
+			fdtp = __dtb_xlp_rvp_begin;
+			break;
+#endif
 #ifdef CONFIG_DT_XLP_GVP
 		case PRID_IMP_NETLOGIC_XLP9XX:
-		case PRID_IMP_NETLOGIC_XLP5XX:
 			fdtp = __dtb_xlp_gvp_begin;
 			break;
 #endif