sh: landisk board support.

This adds support for the I-O DATA Landisk.
Signed-off-by: Nkogiidena <kogiidena@eggplant.ddo.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

arch/sh/Makefile

@@ -105,6 +105,7 @@ machdir-$(CONFIG_SH_RTS7751R2D)			:= renesas/rts7751r2d
 machdir-$(CONFIG_SH_7751_SYSTEMH)		:= renesas/systemh
 machdir-$(CONFIG_SH_EDOSK7705)			:= renesas/edosk7705
 machdir-$(CONFIG_SH_SH4202_MICRODEV)		:= superh/microdev
+machdir-$(CONFIG_SH_LANDISK)			:= landisk
 machdir-$(CONFIG_SH_UNKNOWN)			:= unknown
 
 incdir-y			:= $(notdir $(machdir-y))

arch/sh/boards/landisk/Makefile

+#
+# Makefile for I-O DATA DEVICE, INC. "LANDISK Series"
+#
+
+obj-y	 := setup.o io.o irq.o rtc.o landisk_pwb.o
+
+obj-$(CONFIG_PCI) += pci.o

arch/sh/boards/landisk/io.c

+/*
+ * arch/sh/boards/landisk/io.c
+ *
+ * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
+ * Based largely on io_se.c.
+ *
+ * I/O routine for I-O Data Device, Inc. LANDISK.
+ *
+ * Initial version only to support LAN access; some
+ * placeholder code from io_landisk.c left in with the
+ * expectation of later SuperIO and PCMCIA access.
+ */
+/*
+ * modifed by kogiidena
+ * 2005.03.03
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <asm/io.h>
+#include <asm/landisk/iodata_landisk.h>
+#include <asm/addrspace.h>
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include "../../drivers/pci/pci-sh7751.h"
+
+extern void *area5_io_base;	/* Area 5 I/O Base address */
+extern void *area6_io_base;	/* Area 6 I/O Base address */
+
+/*
+ * The 7751R LANDISK uses the built-in PCI controller (PCIC)
+ * of the 7751R processor, and has a SuperIO accessible via the PCI.
+ * The board also includes a PCMCIA controller on its memory bus,
+ * like the other Solution Engine boards.
+ */
+
+#define PCIIOBR		(volatile long *)PCI_REG(SH7751_PCIIOBR)
+#define PCIMBR          (volatile long *)PCI_REG(SH7751_PCIMBR)
+#define PCI_IO_AREA	SH7751_PCI_IO_BASE
+#define PCI_MEM_AREA	SH7751_PCI_CONFIG_BASE
+
+#define PCI_IOMAP(adr)	(PCI_IO_AREA + (adr & ~SH7751_PCIIOBR_MASK))
+
+#define maybebadio(name,port) \
+  printk("bad PC-like io %s for port 0x%lx at 0x%08x\n", \
+	 #name, (port), (__u32) __builtin_return_address(0))
+
+static inline void delay(void)
+{
+	ctrl_inw(0xa0000000);
+}
+
+static inline unsigned long port2adr(unsigned int port)
+{
+	if ((0x1f0 <= port && port < 0x1f8) || port == 0x3f6)
+		if (port == 0x3f6)
+			return ((unsigned long)area5_io_base + 0x2c);
+		else
+			return ((unsigned long)area5_io_base + PA_PIDE_OFFSET +
+				((port - 0x1f0) << 1));
+	else if ((0x170 <= port && port < 0x178) || port == 0x376)
+		if (port == 0x376)
+			return ((unsigned long)area6_io_base + 0x2c);
+		else
+			return ((unsigned long)area6_io_base + PA_SIDE_OFFSET +
+				((port - 0x170) << 1));
+	else
+		maybebadio(port2adr, (unsigned long)port);
+
+	return port;
+}
+
+/* In case someone configures the kernel w/o PCI support: in that */
+/* scenario, don't ever bother to check for PCI-window addresses */
+
+/* NOTE: WINDOW CHECK MAY BE A BIT OFF, HIGH PCIBIOS_MIN_IO WRAPS? */
+#if defined(CONFIG_PCI)
+#define CHECK_SH7751_PCIIO(port) \
+  ((port >= PCIBIOS_MIN_IO) && (port < (PCIBIOS_MIN_IO + SH7751_PCI_IO_SIZE)))
+#else
+#define CHECK_SH_7751_PCIIO(port) (0)
+#endif
+
+/*
+ * General outline: remap really low stuff [eventually] to SuperIO,
+ * stuff in PCI IO space (at or above window at pci.h:PCIBIOS_MIN_IO)
+ * is mapped through the PCI IO window.  Stuff with high bits (PXSEG)
+ * should be way beyond the window, and is used  w/o translation for
+ * compatibility.
+ */
+unsigned char landisk_inb(unsigned long port)
+{
+	if (PXSEG(port))
+		return *(volatile unsigned char *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		return *(volatile unsigned char *)PCI_IOMAP(port);
+	else
+		return (*(volatile unsigned short *)port2adr(port) & 0xff);
+}
+
+unsigned char landisk_inb_p(unsigned long port)
+{
+	unsigned char v;
+
+	if (PXSEG(port))
+		v = *(volatile unsigned char *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		v = *(volatile unsigned char *)PCI_IOMAP(port);
+	else
+		v = (*(volatile unsigned short *)port2adr(port) & 0xff);
+	delay();
+
+	return v;
+}
+
+unsigned short landisk_inw(unsigned long port)
+{
+	if (PXSEG(port))
+		return *(volatile unsigned short *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		return *(volatile unsigned short *)PCI_IOMAP(port);
+	else
+		maybebadio(inw, port);
+
+	return 0;
+}
+
+unsigned int landisk_inl(unsigned long port)
+{
+	if (PXSEG(port))
+		return *(volatile unsigned long *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		return *(volatile unsigned long *)PCI_IOMAP(port);
+	else
+		maybebadio(inl, port);
+
+	return 0;
+}
+
+void landisk_outb(unsigned char value, unsigned long port)
+{
+
+	if (PXSEG(port))
+		*(volatile unsigned char *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+		*(volatile unsigned char *)PCI_IOMAP(port) = value;
+	else
+		*(volatile unsigned short *)port2adr(port) = value;
+}
+
+void landisk_outb_p(unsigned char value, unsigned long port)
+{
+	if (PXSEG(port))
+		*(volatile unsigned char *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+		*(volatile unsigned char *)PCI_IOMAP(port) = value;
+	else
+		*(volatile unsigned short *)port2adr(port) = value;
+	delay();
+}
+
+void landisk_outw(unsigned short value, unsigned long port)
+{
+	if (PXSEG(port))
+		*(volatile unsigned short *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+		*(volatile unsigned short *)PCI_IOMAP(port) = value;
+	else
+		maybebadio(outw, port);
+}
+
+void landisk_outl(unsigned int value, unsigned long port)
+{
+	if (PXSEG(port))
+		*(volatile unsigned long *)port = value;
+	else if (CHECK_SH7751_PCIIO(port))
+		*(volatile unsigned long *)PCI_IOMAP(port) = value;
+	else
+		maybebadio(outl, port);
+}
+
+void landisk_insb(unsigned long port, void *addr, unsigned long count)
+{
+	if (PXSEG(port))
+		while (count--)
+			*((unsigned char *)addr)++ =
+			    *(volatile unsigned char *)port;
+	else if (CHECK_SH7751_PCIIO(port)) {
+		volatile __u8 *bp = (__u8 *) PCI_IOMAP(port);
+
+		while (count--)
+			*((volatile unsigned char *)addr)++ = *bp;
+	} else {
+		volatile __u16 *p = (volatile unsigned short *)port2adr(port);
+
+		while (count--)
+			*((unsigned char *)addr)++ = *p;
+	}
+}
+
+void landisk_insw(unsigned long port, void *addr, unsigned long count)
+{
+	volatile __u16 *p;
+
+	if (PXSEG(port))
+		p = (volatile unsigned short *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		p = (volatile unsigned short *)PCI_IOMAP(port);
+	else
+		p = (volatile unsigned short *)port2adr(port);
+	while (count--)
+		*((__u16 *) addr)++ = *p;
+}
+
+void landisk_insl(unsigned long port, void *addr, unsigned long count)
+{
+	if (CHECK_SH7751_PCIIO(port)) {
+		volatile __u32 *p = (__u32 *) PCI_IOMAP(port);
+
+		while (count--)
+			*((__u32 *) addr)++ = *p;
+	} else
+		maybebadio(insl, port);
+}
+
+void landisk_outsb(unsigned long port, const void *addr, unsigned long count)
+{
+	if (PXSEG(port))
+		while (count--)
+			*(volatile unsigned char *)port =
+			    *((unsigned char *)addr)++;
+	else if (CHECK_SH7751_PCIIO(port)) {
+		volatile __u8 *bp = (__u8 *) PCI_IOMAP(port);
+
+		while (count--)
+			*bp = *((volatile unsigned char *)addr)++;
+	} else {
+		volatile __u16 *p = (volatile unsigned short *)port2adr(port);
+
+		while (count--)
+			*p = *((unsigned char *)addr)++;
+	}
+}
+
+void landisk_outsw(unsigned long port, const void *addr, unsigned long count)
+{
+	volatile __u16 *p;
+
+	if (PXSEG(port))
+		p = (volatile unsigned short *)port;
+	else if (CHECK_SH7751_PCIIO(port))
+		p = (volatile unsigned short *)PCI_IOMAP(port);
+	else
+		p = (volatile unsigned short *)port2adr(port);
+	while (count--)
+		*p = *((__u16 *) addr)++;
+}
+
+void landisk_outsl(unsigned long port, const void *addr, unsigned long count)
+{
+	if (CHECK_SH7751_PCIIO(port)) {
+		volatile __u32 *p = (__u32 *) PCI_IOMAP(port);
+
+		while (count--)
+			*p = *((__u32 *) addr)++;
+	} else
+		maybebadio(outsl, port);
+}
+
+/* For read/write calls, just copy generic (pass-thru); PCIMBR is  */
+/* already set up.  For a larger memory space, these would need to */
+/* reset PCIMBR as needed on a per-call basis...                   */
+
+unsigned char landisk_readb(unsigned long addr)
+{
+	return *(volatile unsigned char *)addr;
+}
+
+unsigned short landisk_readw(unsigned long addr)
+{
+	return *(volatile unsigned short *)addr;
+}
+
+unsigned int landisk_readl(unsigned long addr)
+{
+	return *(volatile unsigned long *)addr;
+}
+
+void landisk_writeb(unsigned char b, unsigned long addr)
+{
+	*(volatile unsigned char *)addr = b;
+}
+
+void landisk_writew(unsigned short b, unsigned long addr)
+{
+	*(volatile unsigned short *)addr = b;
+}
+
+void landisk_writel(unsigned int b, unsigned long addr)
+{
+	*(volatile unsigned long *)addr = b;
+}
+
+void *landisk_ioremap(unsigned long offset, unsigned long size)
+{
+	if (offset >= 0xfd000000)
+		return (void *)offset;
+	else
+		return (void *)P2SEGADDR(offset);
+}
+
+void landisk_iounmap(void *addr)
+{
+}
+
+/* Map ISA bus address to the real address. Only for PCMCIA.  */
+
+unsigned long landisk_isa_port2addr(unsigned long offset)
+{
+	return port2adr(offset);
+}

arch/sh/boards/landisk/irq.c

+/*
+ * arch/sh/boards/landisk/irq.c
+ *
+ * Copyright (C) 2001  Ian da Silva, Jeremy Siegel
+ * Based largely on io_se.c.
+ *
+ * I/O routine for I-O Data Device, Inc. LANDISK.
+ *
+ * Initial version only to support LAN access; some
+ * placeholder code from io_landisk.c left in with the
+ * expectation of later SuperIO and PCMCIA access.
+ */
+/*
+ * modified by kogiidena
+ * 2005.03.03
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/landisk/iodata_landisk.h>
+
+static void enable_landisk_irq(unsigned int irq);
+static void disable_landisk_irq(unsigned int irq);
+
+/* shutdown is same as "disable" */
+#define shutdown_landisk_irq disable_landisk_irq
+
+static void ack_landisk_irq(unsigned int irq);
+static void end_landisk_irq(unsigned int irq);
+
+static unsigned int startup_landisk_irq(unsigned int irq)
+{
+	enable_landisk_irq(irq);
+	return 0;		/* never anything pending */
+}
+
+static void disable_landisk_irq(unsigned int irq)
+{
+	unsigned long flags;
+	unsigned char val;
+	unsigned char mask = 0xff ^ (0x01 << (irq - 5));
+
+	/* Set the priority in IPR to 0 */
+	local_irq_save(flags);
+	val = ctrl_inb(PA_IMASK);
+	val &= mask;
+	ctrl_outb(val, PA_IMASK);
+	local_irq_restore(flags);
+}
+
+static void enable_landisk_irq(unsigned int irq)
+{
+	unsigned long flags;
+	unsigned char val;
+	unsigned char value = (0x01 << (irq - 5));
+
+	/* Set priority in IPR back to original value */
+	local_irq_save(flags);
+	val = ctrl_inb(PA_IMASK);
+	val |= value;
+	ctrl_outb(val, PA_IMASK);
+	local_irq_restore(flags);
+}
+
+static void ack_landisk_irq(unsigned int irq)
+{
+	disable_landisk_irq(irq);
+}
+
+static void end_landisk_irq(unsigned int irq)
+{
+	if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
+		enable_landisk_irq(irq);
+}
+
+static struct hw_interrupt_type landisk_irq_type = {
+	.typename = "LANDISK IRQ",
+	.startup = startup_landisk_irq,
+	.shutdown = shutdown_landisk_irq,
+	.enable = enable_landisk_irq,
+	.disable = disable_landisk_irq,
+	.ack = ack_landisk_irq,
+	.end = end_landisk_irq
+};
+
+static void make_landisk_irq(unsigned int irq)
+{
+	disable_irq_nosync(irq);
+	irq_desc[irq].handler = &landisk_irq_type;
+	disable_landisk_irq(irq);
+}
+
+/*
+ * Initialize IRQ setting
+ */
+void __init init_landisk_IRQ(void)
+{
+	int i;
+
+	for (i = 5; i < 14; i++)
+		make_landisk_irq(i);
+}

arch/sh/boards/landisk/landisk_pwb.c

+/*
+ * arch/sh/boards/landisk/landisk_pwb.c -- driver for the Power control switch.
+ *
+ * This driver will also support the I-O DATA Device, Inc. LANDISK Board.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copylight (C) 2002 Atom Create Engineering Co., Ltd.
+ *
+ * LED control drive function added by kogiidena
+ */
+
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/major.h>
+#include <linux/poll.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/sched.h>
+#include <linux/timer.h>
+#include <linux/interrupt.h>
+
+#include <asm/system.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/uaccess.h>
+#include <asm/landisk/iodata_landisk.h>
+
+#define SHUTDOWN_BTN_MINOR	1	/* Shutdown button device minor no. */
+#define LED_MINOR	       21	/* LED minor no. */
+#define BTN_MINOR	       22	/* BUTTON minor no. */
+#define GIO_MINOR	       40	/* GIO minor no. */
+
+static int openCnt;
+static int openCntLED;
+static int openCntGio;
+static int openCntBtn;
+static int landisk_btn;
+static int landisk_btnctrlpid;
+/*
+ * Functions prototypes
+ */
+
+static int gio_ioctl(struct inode *inode, struct file *filp, unsigned int cmd,
+		     unsigned long arg);
+
+static int swdrv_open(struct inode *inode, struct file *filp)
+{
+	int minor;
+
+	minor = MINOR(inode->i_rdev);
+	filp->private_data = (void *)minor;
+
+	if (minor == SHUTDOWN_BTN_MINOR) {
+		if (openCnt > 0) {
+			return -EALREADY;
+		} else {
+			openCnt++;
+			return 0;
+		}
+	} else if (minor == LED_MINOR) {
+		if (openCntLED > 0) {
+			return -EALREADY;
+		} else {
+			openCntLED++;
+			return 0;
+		}
+	} else if (minor == BTN_MINOR) {
+		if (openCntBtn > 0) {
+			return -EALREADY;
+		} else {
+			openCntBtn++;
+			return 0;
+		}
+	} else if (minor == GIO_MINOR) {
+		if (openCntGio > 0) {
+			return -EALREADY;
+		} else {
+			openCntGio++;
+			return 0;
+		}
+	}
+	return -ENOENT;
+
+}
+
+static int swdrv_close(struct inode *inode, struct file *filp)
+{
+	int minor;
+
+	minor = MINOR(inode->i_rdev);
+	if (minor == SHUTDOWN_BTN_MINOR) {
+		openCnt--;
+	} else if (minor == LED_MINOR) {
+		openCntLED--;
+	} else if (minor == BTN_MINOR) {
+		openCntBtn--;
+	} else if (minor == GIO_MINOR) {
+		openCntGio--;
+	}
+	return 0;
+}
+
+static int swdrv_read(struct file *filp, char *buff, size_t count,
+		      loff_t * ppos)
+{
+	int minor;
+	minor = (int)(filp->private_data);
+
+	if (!access_ok(VERIFY_WRITE, (void *)buff, count))
+		return -EFAULT;
+
+	if (minor == SHUTDOWN_BTN_MINOR) {
+		if (landisk_btn & 0x10) {
+			put_user(1, buff);
+			return 1;
+		} else {
+			return 0;
+		}
+	}
+	return 0;
+}
+
+static int swdrv_write(struct file *filp, const char *buff, size_t count,
+		       loff_t * ppos)
+{
+	int minor;
+	minor = (int)(filp->private_data);
+
+	if (minor == SHUTDOWN_BTN_MINOR) {
+		return count;
+	}
+	return count;
+}
+
+static irqreturn_t sw_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+	landisk_btn = (0x0ff & (~ctrl_inb(PA_STATUS)));
+	disable_irq(IRQ_BUTTON);
+	disable_irq(IRQ_POWER);
+	ctrl_outb(0x00, PA_PWRINT_CLR);
+
+	if (landisk_btnctrlpid != 0) {
+		kill_proc(landisk_btnctrlpid, SIGUSR1, 1);
+		landisk_btnctrlpid = 0;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static struct file_operations swdrv_fops = {
+	.read = swdrv_read,	/* read */
+	.write = swdrv_write,	/* write */
+	.open = swdrv_open,	/* open */
+	.release = swdrv_close,	/* release */
+	.ioctl = gio_ioctl,	/* ioctl */
+
+};
+
+static char banner[] __initdata =
+    KERN_INFO "LANDISK and USL-5P Button, LED and GIO driver initialized\n";
+
+int __init swdrv_init(void)
+{
+	int error;
+
+	printk("%s", banner);
+
+	openCnt = 0;
+	openCntLED = 0;
+	openCntBtn = 0;
+	openCntGio = 0;
+	landisk_btn = 0;
+	landisk_btnctrlpid = 0;
+
+	if ((error = register_chrdev(SHUTDOWN_BTN_MAJOR, "swdrv", &swdrv_fops))) {
+		printk(KERN_ERR
+		       "Button, LED and GIO driver:Couldn't register driver, error=%d\n",
+		       error);
+		return 1;
+	}
+
+	if (request_irq(IRQ_POWER, sw_interrupt, 0, "SHUTDOWNSWITCH", NULL)) {
+		printk(KERN_ERR "Unable to get IRQ 11.\n");
+		return 1;
+	}
+	if (request_irq(IRQ_BUTTON, sw_interrupt, 0, "USL-5P BUTTON", NULL)) {
+		printk(KERN_ERR "Unable to get IRQ 12.\n");
+		return 1;
+	}
+	ctrl_outb(0x00, PA_PWRINT_CLR);
+
+	return 0;
+}
+
+module_init(swdrv_init);
+
+/*
+ * gio driver
+ *
+ */
+
+#include <asm/landisk/gio.h>
+
+static int gio_ioctl(struct inode *inode, struct file *filp,
+		     unsigned int cmd, unsigned long arg)
+{
+	int minor;
+	unsigned int data, mask;
+	static unsigned int addr = 0;
+
+	minor = (int)(filp->private_data);
+
+	/* access control */
+	if (minor == GIO_MINOR) {
+		;
+	} else if (minor == LED_MINOR) {
+		if (((cmd & 0x0ff) >= 9) && ((cmd & 0x0ff) < 20)) {
+			;
+		} else {
+			return -EINVAL;
+		}
+	} else if (minor == BTN_MINOR) {
+		if (((cmd & 0x0ff) >= 20) && ((cmd & 0x0ff) < 30)) {
+			;
+		} else {
+			return -EINVAL;
+		}
+	} else {
+		return -EINVAL;
+	}
+
+	if (cmd & 0x01) {	/* write */
+		if (copy_from_user(&data, (int *)arg, sizeof(int))) {
+			return -EFAULT;
+		}
+	}
+
+	switch (cmd) {
+	case GIODRV_IOCSGIOSETADDR:	/* addres set */
+		addr = data;
+		break;
+
+	case GIODRV_IOCSGIODATA1:	/* write byte */
+		ctrl_outb((unsigned char)(0x0ff & data), addr);
+		break;
+
+	case GIODRV_IOCSGIODATA2:	/* write word */
+		if (addr & 0x01) {
+			return -EFAULT;
+		}
+		ctrl_outw((unsigned short int)(0x0ffff & data), addr);
+		break;
+
+	case GIODRV_IOCSGIODATA4:	/* write long */
+		if (addr & 0x03) {
+			return -EFAULT;
+		}
+		ctrl_outl(data, addr);
+		break;
+
+	case GIODRV_IOCGGIODATA1:	/* read byte */
+		data = ctrl_inb(addr);
+		break;
+
+	case GIODRV_IOCGGIODATA2:	/* read word */
+		if (addr & 0x01) {
+			return -EFAULT;
+		}
+		data = ctrl_inw(addr);
+		break;
+
+	case GIODRV_IOCGGIODATA4:	/* read long */
+		if (addr & 0x03) {
+			return -EFAULT;
+		}
+		data = ctrl_inl(addr);
+		break;
+	case GIODRV_IOCSGIO_LED:	/* write */
+		mask = ((data & 0x00ffffff) << 8)
+		    | ((data & 0x0000ffff) << 16)
+		    | ((data & 0x000000ff) << 24);
+		landisk_ledparam = data & (~mask);
+		if (landisk_arch == 0) {	/* arch == landisk */
+			landisk_ledparam &= 0x03030303;
+			mask = (~(landisk_ledparam >> 22)) & 0x000c;
+			landisk_ledparam |= mask;
+		} else {	                /* arch == usl-5p */
+			mask = (landisk_ledparam >> 24) & 0x0001;
+			landisk_ledparam |= mask;
+			landisk_ledparam &= 0x007f7f7f;
+		}
+		landisk_ledparam |= 0x80;
+		break;
+	case GIODRV_IOCGGIO_LED:	/* read */
+		data = landisk_ledparam;
+		if (landisk_arch == 0) {	/* arch == landisk */
+			data &= 0x03030303;
+		} else {	                /* arch == usl-5p */
+			;
+		}
+		data &= (~0x080);
+		break;
+	case GIODRV_IOCSGIO_BUZZER:	/* write */
+		landisk_buzzerparam = data;
+		landisk_ledparam |= 0x80;
+		break;
+	case GIODRV_IOCGGIO_LANDISK:	/* read */
+		data = landisk_arch & 0x01;
+		break;
+	case GIODRV_IOCGGIO_BTN:	/* read */
+		data = (0x0ff & ctrl_inb(PA_PWRINT_CLR));
+		data <<= 8;
+		data |= (0x0ff & ctrl_inb(PA_IMASK));
+		data <<= 8;
+		data |= (0x0ff & landisk_btn);
+		data <<= 8;
+		data |= (0x0ff & (~ctrl_inb(PA_STATUS)));
+		break;
+	case GIODRV_IOCSGIO_BTNPID:	/* write */
+		landisk_btnctrlpid = data;
+		landisk_btn = 0;
+		if (irq_desc[IRQ_BUTTON].depth) {
+			enable_irq(IRQ_BUTTON);
+		}
+		if (irq_desc[IRQ_POWER].depth) {
+			enable_irq(IRQ_POWER);
+		}
+		break;
+	case GIODRV_IOCGGIO_BTNPID:	/* read */
+		data = landisk_btnctrlpid;
+		break;
+	default:
+		return -EFAULT;
+		break;
+	}
+
+	if ((cmd & 0x01) == 0) {	/* read */
+		if (copy_to_user((int *)arg, &data, sizeof(int))) {
+			return -EFAULT;
+		}
+	}
+	return 0;
+}

arch/sh/boards/landisk/rtc.c

+/*
+ * arch/sh/boards/landisk/rtc.c --  RTC support
+ *
+ *  Copyright (C) 2000  Philipp Rumpf <prumpf@tux.org>
+ *  Copyright (C) 1999  Tetsuya Okada & Niibe Yutaka
+ */
+/*
+ * modifed by kogiidena
+ * 2005.09.16
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+
+#ifndef BCD_TO_BIN
+#define BCD_TO_BIN(val) ((val)=((val)&15) + ((val)>>4)*10)
+#endif
+
+#ifndef BIN_TO_BCD
+#define BIN_TO_BCD(val) ((val)=(((val)/10)<<4) + (val)%10)
+#endif
+
+extern void (*rtc_get_time) (struct timespec *);
+extern int (*rtc_set_time) (const time_t);
+extern spinlock_t rtc_lock;
+
+extern void
+rs5c313_set_cmos_time(unsigned int BCD_yr, unsigned int BCD_mon,
+		      unsigned int BCD_day, unsigned int BCD_hr,
+		      unsigned int BCD_min, unsigned int BCD_sec);
+
+extern unsigned long
+rs5c313_get_cmos_time(unsigned int *BCD_yr, unsigned int *BCD_mon,
+		      unsigned int *BCD_day, unsigned int *BCD_hr,
+		      unsigned int *BCD_min, unsigned int *BCD_sec);
+
+void landisk_rtc_gettimeofday(struct timespec *tv)
+{
+	unsigned int BCD_yr, BCD_mon, BCD_day, BCD_hr, BCD_min, BCD_sec;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+	tv->tv_sec = rs5c313_get_cmos_time
+	    (&BCD_yr, &BCD_mon, &BCD_day, &BCD_hr, &BCD_min, &BCD_sec);
+	tv->tv_nsec = 0;
+	spin_unlock_irqrestore(&rtc_lock, flags);
+}
+
+int landisk_rtc_settimeofday(const time_t secs)
+{
+	int retval = 0;
+	int real_seconds, real_minutes, cmos_minutes;
+	unsigned long flags;
+	unsigned long nowtime = secs;
+	unsigned int BCD_yr, BCD_mon, BCD_day, BCD_hr, BCD_min, BCD_sec;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+
+	rs5c313_get_cmos_time
+	  (&BCD_yr, &BCD_mon, &BCD_day, &BCD_hr, &BCD_min, &BCD_sec);
+	cmos_minutes = BCD_min;
+	BCD_TO_BIN(cmos_minutes);
+
+	/*
+	 * since we're only adjusting minutes and seconds,
+	 * don't interfere with hour overflow. This avoids
+	 * messing with unknown time zones but requires your
+	 * RTC not to be off by more than 15 minutes
+	 */
+	real_seconds = nowtime % 60;
+	real_minutes = nowtime / 60;
+	if (((abs(real_minutes - cmos_minutes) + 15) / 30) & 1)
+		real_minutes += 30;	/* correct for half hour time zone */
+	real_minutes %= 60;
+
+	if (abs(real_minutes - cmos_minutes) < 30) {
+		BIN_TO_BCD(real_seconds);
+		BIN_TO_BCD(real_minutes);
+		rs5c313_set_cmos_time(BCD_yr, BCD_mon, BCD_day, BCD_hr,
+				      real_minutes, real_seconds);
+	} else {
+		printk(KERN_WARNING
+		       "set_rtc_time: can't update from %d to %d\n",
+		       cmos_minutes, real_minutes);
+		retval = -1;
+	}
+
+	spin_unlock_irqrestore(&rtc_lock, flags);
+	return retval;
+}
+
+
+void landisk_time_init(void)
+{
+	rtc_get_time = landisk_rtc_gettimeofday;
+	rtc_set_time = landisk_rtc_settimeofday;
+}

arch/sh/boards/landisk/setup.c

+/*
+ * arch/sh/boards/landisk/setup.c
+ *
+ * Copyright (C) 2002 Paul Mundt
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License.  See linux/COPYING for more information.
+ *
+ * Setup code for an unknown machine (internal peripherials only)
+ */
+/*
+ * linux/arch/sh/kernel/setup_landisk.c
+ *
+ * Copyright (C) 2000  Kazumoto Kojima
+ *
+ * I-O DATA Device, Inc. LANDISK Support.
+ *
+ * Modified for LANDISK by
+ * Atom Create Engineering Co., Ltd. 2002.
+ */
+/*
+ * modifed by kogiidena
+ * 2005.09.16
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/pm.h>
+
+#include <linux/hdreg.h>
+#include <linux/ide.h>
+#include <linux/pci.h>
+
+#include <asm/machvec.h>
+#include <asm/rtc.h>
+#include <asm/machvec_init.h>
+#include <asm/io.h>
+#include <asm/landisk/iodata_landisk.h>
+#include <asm/landisk/io.h>
+
+#include <linux/mm.h>
+#include <linux/vmalloc.h>
+
+extern void (*board_time_init) (void);
+void landisk_time_init(void);
+extern void init_landisk_IRQ(void);
+
+int landisk_ledparam;
+int landisk_buzzerparam;
+int landisk_arch;
+
+/* defined in mm/ioremap.c */
+extern void *p3_ioremap(unsigned long phys_addr, unsigned long size,
+			unsigned long flags);
+
+/*
+ * Initialize the board
+ */
+
+const char *get_system_type(void)
+{
+	return "LANDISK";
+}
+
+static void landisk_power_off(void)
+{
+	ctrl_outb(0x01, PA_SHUTDOWN);
+}
+
+void check_usl5p(void)
+{
+	volatile unsigned char *p = (volatile unsigned char *)PA_LED;
+	unsigned char tmp1, tmp2;
+	tmp1 = *p;
+	*p = 0x40;
+	tmp2 = *p;
+	*p = tmp1;
+	landisk_arch = (tmp2 == 0x40) ? 1 : 0;
+	if (landisk_arch == 1) {	/* arch == usl-5p */
+		landisk_ledparam = 0x00000380;
+		landisk_ledparam |= (tmp1 & 0x07c);
+	} else {                        /* arch == landisk */
+		landisk_ledparam = 0x02000180;
+		landisk_ledparam |= 0x04;
+	}
+	return;
+}
+
+void __init platform_setup(void)
+{
+
+	landisk_buzzerparam = 0;
+	check_usl5p();
+
+	printk(KERN_INFO "I-O DATA DEVICE, INC. \"LANDISK Series\" support.\n");
+	board_time_init = landisk_time_init;
+	pm_power_off = landisk_power_off;
+
+}
+
+void *area5_io_base;
+void *area6_io_base;
+
+int __init cf_init(void)
+{
+	pgprot_t prot;
+	unsigned long paddrbase, psize;
+
+	/* open I/O area window */
+	paddrbase = virt_to_phys((void *)PA_AREA5_IO);
+	psize = PAGE_SIZE;
+	prot = PAGE_KERNEL_PCC(1, _PAGE_PCC_IO16);
+	area5_io_base = p3_ioremap(paddrbase, psize, prot.pgprot);
+	if (!area5_io_base) {
+		printk("allocate_cf_area : can't open CF I/O window!\n");
+		return -ENOMEM;
+	}
+
+	paddrbase = virt_to_phys((void *)PA_AREA6_IO);
+	psize = PAGE_SIZE;
+	prot = PAGE_KERNEL_PCC(0, _PAGE_PCC_IO16);
+	area6_io_base = p3_ioremap(paddrbase, psize, prot.pgprot);
+	if (!area6_io_base) {
+		printk("allocate_cf_area : can't open HDD I/O window!\n");
+		return -ENOMEM;
+	}
+
+	printk(KERN_INFO "Allocate Area5/6 success.\n");
+
+	/* XXX : do we need attribute and common-memory area also? */
+
+	return 0;
+}
+
+__initcall(cf_init);
+
+#include <linux/sched.h>
+
+/* Cycle the LED's in the clasic knightrider/Sun pattern */
+
+void heartbeat_landisk(void)
+{
+	static unsigned int cnt = 0, blink = 0x00, period = 25;
+	volatile unsigned char *p = (volatile unsigned char *)PA_LED;
+	char data;
+
+	if ((landisk_ledparam & 0x080) == 0) {
+		return;
+	}
+	cnt += 1;
+	if (cnt < period) {
+		return;
+	}
+	cnt = 0;
+	blink++;
+
+	data = (blink & 0x01) ? (landisk_ledparam >> 16) : 0;
+	data |= (blink & 0x02) ? (landisk_ledparam >> 8) : 0;
+	data |= landisk_ledparam;
+
+	/* buzzer */
+	if (landisk_buzzerparam & 0x1) {
+		data |= 0x80;
+	} else {
+		data &= 0x7f;
+	}
+	*p = data;
+
+	if (((landisk_ledparam & 0x007f7f00) == 0)
+	    && (landisk_buzzerparam == 0)) {
+		landisk_ledparam &= (~0x0080);
+	}
+	landisk_buzzerparam >>= 1;
+}
+
+/*
+ * The Machine Vector
+ */
+
+struct sh_machine_vector mv_landisk __initmv = {
+	.mv_nr_irqs = 72,
+	.mv_inb = landisk_inb,
+	.mv_inw = landisk_inw,
+	.mv_inl = landisk_inl,
+	.mv_outb = landisk_outb,
+	.mv_outw = landisk_outw,
+	.mv_outl = landisk_outl,
+	.mv_inb_p = landisk_inb_p,
+	.mv_inw_p = landisk_inw,
+	.mv_inl_p = landisk_inl,
+	.mv_outb_p = landisk_outb_p,
+	.mv_outw_p = landisk_outw,
+	.mv_outl_p = landisk_outl,
+	.mv_insb = landisk_insb,
+	.mv_insw = landisk_insw,
+	.mv_insl = landisk_insl,
+	.mv_outsb = landisk_outsb,
+	.mv_outsw = landisk_outsw,
+	.mv_outsl = landisk_outsl,
+	.mv_readb = landisk_readb,
+	.mv_readw = landisk_readw,
+	.mv_readl = landisk_readl,
+	.mv_writeb = landisk_writeb,
+	.mv_writew = landisk_writew,
+	.mv_writel = landisk_writel,
+	.mv_ioremap = landisk_ioremap,
+	.mv_iounmap = landisk_iounmap,
+	.mv_isa_port2addr = landisk_isa_port2addr,
+	.mv_init_irq = init_landisk_IRQ,
+
+#ifdef CONFIG_HEARTBEAT
+	.mv_heartbeat = heartbeat_landisk,
+#endif
+
+};
+
+ALIAS_MV(landisk)

arch/sh/tools/mach-types

@@ -25,4 +25,4 @@ RTS7751R2D		SH_RTS7751R2D
 EDOSK7705		SH_EDOSK7705
 SH4202_MICRODEV		SH_SH4202_MICRODEV
 SH03			SH_SH03
-
+LANDISK			SH_LANDISK

include/asm-sh/landisk/gio.h

+#ifndef __ASM_SH_LANDISK_GIO_H
+#define __ASM_SH_LANDISK_GIO_H
+
+#include <linux/ioctl.h>
+
+/* version */
+#define VERSION_STR	"1.00"
+
+/* Driver name */
+#define GIO_DRIVER_NAME		"/dev/giodrv"
+
+/* Use 'k' as magic number */
+#define GIODRV_IOC_MAGIC  'k'
+
+#define GIODRV_IOCRESET    _IO(GIODRV_IOC_MAGIC, 0)
+/*
+ * S means "Set" through a ptr,
+ * T means "Tell" directly
+ * G means "Get" (to a pointed var)
+ * Q means "Query", response is on the return value
+ * X means "eXchange": G and S atomically
+ * H means "sHift": T and Q atomically
+ */
+#define GIODRV_IOCSGIODATA1   _IOW(GIODRV_IOC_MAGIC,  1, unsigned char *)
+#define GIODRV_IOCGGIODATA1   _IOR(GIODRV_IOC_MAGIC,  2, unsigned char *)
+#define GIODRV_IOCSGIODATA2   _IOW(GIODRV_IOC_MAGIC,  3, unsigned short *)
+#define GIODRV_IOCGGIODATA2   _IOR(GIODRV_IOC_MAGIC,  4, unsigned short *)
+#define GIODRV_IOCSGIODATA4   _IOW(GIODRV_IOC_MAGIC,  5, unsigned long *)
+#define GIODRV_IOCGGIODATA4   _IOR(GIODRV_IOC_MAGIC,  6, unsigned long *)
+#define GIODRV_IOCSGIOSETADDR _IOW(GIODRV_IOC_MAGIC,  7, unsigned long *)
+#define GIODRV_IOCHARDRESET   _IO(GIODRV_IOC_MAGIC, 8) /* debugging tool */
+
+#define GIODRV_IOCSGIO_LED    _IOW(GIODRV_IOC_MAGIC,  9, unsigned long *)
+#define GIODRV_IOCGGIO_LED    _IOR(GIODRV_IOC_MAGIC,  10, unsigned long *)
+#define GIODRV_IOCSGIO_BUZZER _IOW(GIODRV_IOC_MAGIC,  11, unsigned long *)
+#define GIODRV_IOCGGIO_LANDISK _IOR(GIODRV_IOC_MAGIC,  14, unsigned long *)
+#define GIODRV_IOCGGIO_BTN _IOR(GIODRV_IOC_MAGIC,  22, unsigned long *)
+#define GIODRV_IOCSGIO_BTNPID _IOW(GIODRV_IOC_MAGIC,  23, unsigned long *)
+#define GIODRV_IOCGGIO_BTNPID _IOR(GIODRV_IOC_MAGIC,  24, unsigned long *)
+
+#define GIODRV_IOC_MAXNR 8
+#define GIO_READ 0x00000000
+#define GIO_WRITE 0x00000001
+
+#endif /* __ASM_SH_LANDISK_GIO_H  */

include/asm-sh/landisk/ide.h

+/*
+ * modifed by kogiidena
+ * 2005.03.03
+ */
+
+#ifndef __ASM_SH_LANDISK_IDE_H
+#define __ASM_SH_LANDISK_IDE_H
+
+/* Nothing to see here.. */
+#include <asm/landisk/iodata_landisk.h>
+#define IRQ_CFCARD	IRQ_FATA	/* CF Card IRQ */
+#define IRQ_PCMCIA	IRQ_ATA		/* PCMCIA IRQ */
+
+#endif /* __ASM_SH_LANDISK_IDE_H  */

include/asm-sh/landisk/iodata_landisk.h

+#ifndef __ASM_SH_IODATA_LANDISK_H
+#define __ASM_SH_IODATA_LANDISK_H
+
+/*
+ * linux/include/asm-sh/landisk/iodata_landisk.h
+ *
+ * Copyright (C) 2000  Atom Create Engineering Co., Ltd.
+ *
+ * IO-DATA LANDISK support
+ */
+
+/* Box specific addresses.  */
+
+#define PA_USB		0xa4000000	/* USB Controller M66590 */
+
+#define PA_ATARST	0xb0000000	/* ATA/FATA Access Control Register */
+#define PA_LED		0xb0000001	/* LED Control Register */
+#define PA_STATUS	0xb0000002	/* Switch Status Register */
+#define PA_SHUTDOWN	0xb0000003	/* Shutdown Control Register */
+#define PA_PCIPME	0xb0000004	/* PCI PME Status Register */
+#define PA_IMASK	0xb0000005	/* Interrupt Mask Register */
+/* 2003.10.31 I-O DATA NSD NWG	add.	for shutdown port clear */
+#define PA_PWRINT_CLR	0xb0000006	/* Shutdown Interrupt clear Register */
+
+#define PA_AREA5_IO	0xb4000000	/* Area 5 IO Memory */
+#define PA_AREA6_IO	0xb8000000	/* Area 6 IO Memory */
+#define PA_LCD_CLRDSP	0x00		/* LCD Clear Display Offset */
+#define PA_LCD_RTNHOME	0x00		/* LCD Return Home Offset */
+#define PA_LCD_ENTMODE	0x00		/* LCD Entry Mode Offset */
+#define PA_LCD_DSPCTL	0x00		/* LCD Display ON/OFF Control Offset */
+#define PA_LCD_FUNC	0x00		/* LCD Function Set Offset */
+#define PA_LCD_CGRAM	0x00		/* LCD Set CGRAM Address Offset */
+#define PA_LCD_DDRAM	0x00		/* LCD Set DDRAM Address Offset */
+#define PA_LCD_RDFLAG	0x01		/* LCD Read Busy Flag Offset */
+#define PA_LCD_WTDATA	0x02		/* LCD Write Datat to RAM Offset */
+#define PA_LCD_RDDATA	0x03		/* LCD Read Data from RAM Offset */
+#define PA_PIDE_OFFSET	0x40		/* CF IDE Offset */
+#define PA_SIDE_OFFSET	0x40		/* HDD IDE Offset */
+
+#define IRQ_PCIINTA	5		/* PCI INTA IRQ */
+#define IRQ_PCIINTB	6		/* PCI INTB IRQ */
+#define IRQ_PCIINDC	7		/* PCI INTC IRQ */
+#define IRQ_PCIINTD	8		/* PCI INTD IRQ */
+#define IRQ_ATA		9		/* ATA IRQ */
+#define IRQ_FATA	10		/* FATA IRQ */
+#define IRQ_POWER	11		/* Power Switch IRQ */
+#define IRQ_BUTTON	12		/* USL-5P Button IRQ */
+#define IRQ_FAULT	13		/* USL-5P Fault  IRQ */
+
+#define SHUTDOWN_BTN_MAJOR	99	/* Shutdown button device major no. */
+
+#define SHUTDOWN_LOOP_CNT	5	/* Shutdown button Detection loop */
+#define SHUTDOWN_DELAY		200	/* Shutdown button delay value(ms) */
+
+
+/* added by kogiidena */
+/*
+ *  landisk_ledparam
+ *
+ * led  ------10 -6543210 -6543210 -6543210
+ *     |000000..|0.......|0.......|U.......|
+ *     |  HARD  |fastblik| blink  |   on   |
+ *
+ *   led0: power       U:update flag
+ *   led1: error
+ *   led2: usb1
+ *   led3: usb2
+ *   led4: usb3
+ *   led5: usb4
+ *   led6: usb5
+ *
+ */
+extern int landisk_ledparam;    /* from setup.c */
+extern int landisk_buzzerparam; /* from setup.c */
+extern int landisk_arch;        /* from setup.c */
+
+#endif  /* __ASM_SH_IODATA_LANDISK_H */
+