Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
提交 8f67eeb0 编写于 作者: W Wolfram Sang 提交者： Jean Delvare
浏览文件
操作

i2c/chips: Remove deprecated pcf8575 driver 

The pcf8575 driver in drivers/i2c/chips which just exports its register to
sysfs is superseded by drivers/gpio/pcf857x.c which properly uses the gpiolib.
As this driver has been deprecated for more than a year, finally remove it.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Cc: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
上级 4ba2ccb8
隐藏空白更改
内联 并排
Showing with 0 addition and 286 deletion
Documentation/i2c/chips/pcf8575 已删除 100644 → 0
浏览文件 @ 4ba2ccb8
About the PCF8575 chip and the pcf8575 kernel driver
====================================================
The PCF8575 chip is produced by the following manufacturers:
* Philips NXP
http://www.nxp.com/#/pip/cb=[type=product,path=50807/41735/41850,final=PCF8575_3]|pip=[pip=PCF8575_3][0]
* Texas Instruments
http://focus.ti.com/docs/prod/folders/print/pcf8575.html
Some vendors sell small PCB's with the PCF8575 mounted on it. You can connect
such a board to a Linux host via e.g. an USB to I2C interface. Examples of
PCB boards with a PCF8575:
* SFE Breakout Board for PCF8575 I2C Expander by RobotShop
http://www.robotshop.ca/home/products/robot-parts/electronics/adapters-converters/sfe-pcf8575-i2c-expander-board.html
* Breakout Board for PCF8575 I2C Expander by Spark Fun Electronics
http://www.sparkfun.com/commerce/product_info.php?products_id=8130
Description
-----------
The PCF8575 chip is a 16-bit I/O expander for the I2C bus. Up to eight of
these chips can be connected to the same I2C bus. You can find this
chip on some custom designed hardware, but you won't find it on PC
motherboards.
The PCF8575 chip consists of a 16-bit quasi-bidirectional port and an I2C-bus
interface. Each of the sixteen I/O's can be independently used as an input or
an output. To set up an I/O pin as an input, you have to write a 1 to the
corresponding output.
For more information please see the datasheet.
Detection
---------
There is no method known to detect whether a chip on a given I2C address is
a PCF8575 or whether it is any other I2C device, so you have to pass the I2C
bus and address of the installed PCF8575 devices explicitly to the driver at
load time via the force=... parameter.
/sys interface
--------------
For each address on which a PCF8575 chip was found or forced the following
files will be created under /sys:
* /sys/bus/i2c/devices/<bus>-<address>/read
* /sys/bus/i2c/devices/<bus>-<address>/write
where bus is the I2C bus number (0, 1, ...) and address is the four-digit
hexadecimal representation of the 7-bit I2C address of the PCF8575
(0020 .. 0027).
The read file is read-only. Reading it will trigger an I2C read and will hence
report the current input state for the pins configured as inputs, and the
current output value for the pins configured as outputs.
The write file is read-write. Writing a value to it will configure all pins
as output for which the corresponding bit is zero. Reading the write file will
return the value last written, or -EAGAIN if no value has yet been written to
the write file.
On module initialization the configuration of the chip is not changed -- the
chip is left in the state it was already configured in through either power-up
or through previous I2C write actions.
drivers/i2c/chips/Kconfig
浏览文件 @ 8f67eeb0
......@@ -33,24 +33,6 @@ config SENSORS_PCF8574
These devices are hard to detect and rarely found on mainstream
hardware. If unsure, say N.
config PCF8575
tristate "Philips PCF8575 (DEPRECATED)"
default n
depends on GPIO_PCF857X = "n"
help
If you say yes here you get support for Philips PCF8575 chip.
This chip is a 16-bit I/O expander for the I2C bus. Several other
chip manufacturers sell equivalent chips, e.g. Texas Instruments.
This driver can also be built as a module. If so, the module
will be called pcf8575.
This driver is deprecated and will be dropped soon. Use
drivers/gpio/pcf857x.c instead.
This device is hard to detect and is rarely found on mainstream
hardware. If unsure, say N.
config SENSORS_PCA9539
tristate "Philips PCA9539 16-bit I/O port (DEPRECATED)"
depends on EXPERIMENTAL && GPIO_PCA953X = "n"
......
drivers/i2c/chips/Makefile
浏览文件 @ 8f67eeb0
......@@ -13,7 +13,6 @@
obj-$(CONFIG_DS1682) += ds1682.o
obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o
obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o
obj-$(CONFIG_PCF8575) += pcf8575.o
obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o
ifeq ($(CONFIG_I2C_DEBUG_CHIP),y)
......
drivers/i2c/chips/pcf8575.c 已删除 100644 → 0
浏览文件 @ 4ba2ccb8
/*
pcf8575.c
About the PCF8575 chip: the PCF8575 is a 16-bit I/O expander for the I2C bus
produced by a.o. Philips Semiconductors.
Copyright (C) 2006 Michael Hennerich, Analog Devices Inc.
<hennerich@blackfin.uclinux.org>
Based on pcf8574.c.
Copyright (c) 2007 Bart Van Assche <bart.vanassche@gmail.com>.
Ported this driver from ucLinux to the mainstream Linux kernel.
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/i2c.h>
#include <linux/slab.h> /* kzalloc() */
#include <linux/sysfs.h> /* sysfs_create_group() */
/* Addresses to scan: none, device can't be detected */
static const unsigned short normal_i2c[] = { I2C_CLIENT_END };
/* Insmod parameters */
I2C_CLIENT_INSMOD;
/* Each client has this additional data */
struct pcf8575_data {
int write; /* last written value, or error code */
};
/* following are the sysfs callback functions */
static ssize_t show_read(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct i2c_client *client = to_i2c_client(dev);
u16 val;
u8 iopin_state[2];
i2c_master_recv(client, iopin_state, 2);
val = iopin_state[0];
val |= iopin_state[1] << 8;
return sprintf(buf, "%u\n", val);
}
static DEVICE_ATTR(read, S_IRUGO, show_read, NULL);
static ssize_t show_write(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct pcf8575_data *data = dev_get_drvdata(dev);
if (data->write < 0)
return data->write;
return sprintf(buf, "%d\n", data->write);
}
static ssize_t set_write(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct i2c_client *client = to_i2c_client(dev);
struct pcf8575_data *data = i2c_get_clientdata(client);
unsigned long val = simple_strtoul(buf, NULL, 10);
u8 iopin_state[2];
if (val > 0xffff)
return -EINVAL;
data->write = val;
iopin_state[0] = val & 0xFF;
iopin_state[1] = val >> 8;
i2c_master_send(client, iopin_state, 2);
return count;
}
static DEVICE_ATTR(write, S_IWUSR | S_IRUGO, show_write, set_write);
static struct attribute *pcf8575_attributes[] = {
&dev_attr_read.attr,
&dev_attr_write.attr,
NULL
};
static const struct attribute_group pcf8575_attr_group = {
.attrs = pcf8575_attributes,
};
/*
* Real code
*/
/* Return 0 if detection is successful, -ENODEV otherwise */
static int pcf8575_detect(struct i2c_client *client, int kind,
struct i2c_board_info *info)
{
struct i2c_adapter *adapter = client->adapter;
if (!i2c_check_functionality(adapter, I2C_FUNC_I2C))
return -ENODEV;
/* This is the place to detect whether the chip at the specified
address really is a PCF8575 chip. However, there is no method known
to detect whether an I2C chip is a PCF8575 or any other I2C chip. */
strlcpy(info->type, "pcf8575", I2C_NAME_SIZE);
return 0;
}
static int pcf8575_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct pcf8575_data *data;
int err;
data = kzalloc(sizeof(struct pcf8575_data), GFP_KERNEL);
if (!data) {
err = -ENOMEM;
goto exit;
}
i2c_set_clientdata(client, data);
data->write = -EAGAIN;
/* Register sysfs hooks */
err = sysfs_create_group(&client->dev.kobj, &pcf8575_attr_group);
if (err)
goto exit_free;
return 0;
exit_free:
kfree(data);
exit:
return err;
}
static int pcf8575_remove(struct i2c_client *client)
{
sysfs_remove_group(&client->dev.kobj, &pcf8575_attr_group);
kfree(i2c_get_clientdata(client));
return 0;
}
static const struct i2c_device_id pcf8575_id[] = {
{ "pcf8575", 0 },
{ }
};
static struct i2c_driver pcf8575_driver = {
.driver = {
.owner = THIS_MODULE,
.name = "pcf8575",
},
.probe = pcf8575_probe,
.remove = pcf8575_remove,
.id_table = pcf8575_id,
.detect = pcf8575_detect,
.address_data = &addr_data,
};
static int __init pcf8575_init(void)
{
return i2c_add_driver(&pcf8575_driver);
}
static void __exit pcf8575_exit(void)
{
i2c_del_driver(&pcf8575_driver);
}
MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>, "
"Bart Van Assche <bart.vanassche@gmail.com>");
MODULE_DESCRIPTION("pcf8575 driver");
MODULE_LICENSE("GPL");
module_init(pcf8575_init);
module_exit(pcf8575_exit);
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或