提交 8a13ecd7 编写于 作者: R Ralf Baechle

[MIPS] IP32: Fixes after interrupt renumbering.

And general untangling.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
上级 725d7b36
......@@ -40,13 +40,6 @@ static void inline flush_mace_bus(void)
mace->perif.ctrl.misc;
}
#undef DEBUG_IRQ
#ifdef DEBUG_IRQ
#define DBG(x...) printk(x)
#else
#define DBG(x...)
#endif
/*
* O2 irq map
*
......@@ -125,6 +118,7 @@ struct irqaction memerr_irq = {
.mask = CPU_MASK_NONE,
.name = "CRIME memory error",
};
struct irqaction cpuerr_irq = {
.handler = crime_cpuerr_intr,
.flags = IRQF_DISABLED,
......@@ -139,46 +133,70 @@ struct irqaction cpuerr_irq = {
static uint64_t crime_mask;
static void enable_crime_irq(unsigned int irq)
static inline void crime_enable_irq(unsigned int irq)
{
crime_mask |= 1 << (irq - 1);
unsigned int bit = irq - CRIME_IRQ_BASE;
crime_mask |= 1 << bit;
crime->imask = crime_mask;
}
static void disable_crime_irq(unsigned int irq)
static inline void crime_disable_irq(unsigned int irq)
{
crime_mask &= ~(1 << (irq - 1));
unsigned int bit = irq - CRIME_IRQ_BASE;
crime_mask &= ~(1 << bit);
crime->imask = crime_mask;
flush_crime_bus();
}
static void mask_and_ack_crime_irq(unsigned int irq)
static void crime_level_mask_and_ack_irq(unsigned int irq)
{
crime_disable_irq(irq);
}
static void crime_level_end_irq(unsigned int irq)
{
if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
crime_enable_irq(irq);
}
static struct irq_chip crime_level_interrupt = {
.name = "IP32 CRIME",
.ack = crime_level_mask_and_ack_irq,
.mask = crime_disable_irq,
.mask_ack = crime_level_mask_and_ack_irq,
.unmask = crime_enable_irq,
.end = crime_level_end_irq,
};
static void crime_edge_mask_and_ack_irq(unsigned int irq)
{
unsigned int bit = irq - CRIME_IRQ_BASE;
uint64_t crime_int;
/* Edge triggered interrupts must be cleared. */
if ((irq >= CRIME_GBE0_IRQ && irq <= CRIME_GBE3_IRQ)
|| (irq >= CRIME_RE_EMPTY_E_IRQ && irq <= CRIME_RE_IDLE_E_IRQ)
|| (irq >= CRIME_SOFT0_IRQ && irq <= CRIME_SOFT2_IRQ)) {
uint64_t crime_int;
crime_int = crime->hard_int;
crime_int &= ~(1 << (irq - 1));
crime->hard_int = crime_int;
}
disable_crime_irq(irq);
crime_int = crime->hard_int;
crime_int &= ~(1 << bit);
crime->hard_int = crime_int;
crime_disable_irq(irq);
}
static void end_crime_irq(unsigned int irq)
static void crime_edge_end_irq(unsigned int irq)
{
if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
enable_crime_irq(irq);
crime_enable_irq(irq);
}
static struct irq_chip ip32_crime_interrupt = {
.name = "IP32 CRIME",
.ack = mask_and_ack_crime_irq,
.mask = disable_crime_irq,
.mask_ack = mask_and_ack_crime_irq,
.unmask = enable_crime_irq,
.end = end_crime_irq,
static struct irq_chip crime_edge_interrupt = {
.name = "IP32 CRIME",
.ack = crime_edge_mask_and_ack_irq,
.mask = crime_disable_irq,
.mask_ack = crime_edge_mask_and_ack_irq,
.unmask = crime_enable_irq,
.end = crime_edge_end_irq,
};
/*
......@@ -265,7 +283,7 @@ static void enable_maceisa_irq(unsigned int irq)
{
unsigned int crime_int = 0;
DBG("maceisa enable: %u\n", irq);
pr_debug("maceisa enable: %u\n", irq);
switch (irq) {
case MACEISA_AUDIO_SW_IRQ ... MACEISA_AUDIO3_MERR_IRQ:
......@@ -278,7 +296,7 @@ static void enable_maceisa_irq(unsigned int irq)
crime_int = MACE_SUPERIO_INT;
break;
}
DBG("crime_int %08x enabled\n", crime_int);
pr_debug("crime_int %08x enabled\n", crime_int);
crime_mask |= crime_int;
crime->imask = crime_mask;
maceisa_mask |= 1 << (irq - 33);
......@@ -290,11 +308,11 @@ static void disable_maceisa_irq(unsigned int irq)
unsigned int crime_int = 0;
maceisa_mask &= ~(1 << (irq - 33));
if(!(maceisa_mask & MACEISA_AUDIO_INT))
if (!(maceisa_mask & MACEISA_AUDIO_INT))
crime_int |= MACE_AUDIO_INT;
if(!(maceisa_mask & MACEISA_MISC_INT))
if (!(maceisa_mask & MACEISA_MISC_INT))
crime_int |= MACE_MISC_INT;
if(!(maceisa_mask & MACEISA_SUPERIO_INT))
if (!(maceisa_mask & MACEISA_SUPERIO_INT))
crime_int |= MACE_SUPERIO_INT;
crime_mask &= ~crime_int;
crime->imask = crime_mask;
......@@ -327,12 +345,12 @@ static void end_maceisa_irq(unsigned irq)
}
static struct irq_chip ip32_maceisa_interrupt = {
.name = "IP32 MACE ISA",
.ack = mask_and_ack_maceisa_irq,
.mask = disable_maceisa_irq,
.mask_ack = mask_and_ack_maceisa_irq,
.unmask = enable_maceisa_irq,
.end = end_maceisa_irq,
.name = "IP32 MACE ISA",
.ack = mask_and_ack_maceisa_irq,
.mask = disable_maceisa_irq,
.mask_ack = mask_and_ack_maceisa_irq,
.unmask = enable_maceisa_irq,
.end = end_maceisa_irq,
};
/* This is used for regular non-ISA, non-PCI MACE interrupts. That means
......@@ -411,7 +429,7 @@ static void ip32_irq0(void)
irq = __ffs(mace_int & maceisa_mask) + MACEISA_AUDIO_SW_IRQ;
}
DBG("*irq %u*\n", irq);
pr_debug("*irq %u*\n", irq);
do_IRQ(irq);
}
......@@ -472,23 +490,31 @@ void __init arch_init_irq(void)
mips_cpu_irq_init();
for (irq = MIPS_CPU_IRQ_BASE + 8; irq <= IP32_IRQ_MAX; irq++) {
struct irq_chip *chip;
switch (irq) {
case MACE_VID_IN1_IRQ ... MACE_PCI_BRIDGE_IRQ:
chip = &ip32_mace_interrupt;
set_irq_chip(irq, &ip32_mace_interrupt);
break;
case MACEPCI_SCSI0_IRQ ... MACEPCI_SHARED2_IRQ:
chip = &ip32_macepci_interrupt;
set_irq_chip(irq, &ip32_macepci_interrupt);
break;
case CRIME_GBE0_IRQ ... CRIME_GBE3_IRQ:
set_irq_chip(irq, &crime_edge_interrupt);
break;
case CRIME_CPUERR_IRQ:
case CRIME_MEMERR_IRQ:
set_irq_chip(irq, &crime_level_interrupt);
break;
case CRIME_GBE0_IRQ ... CRIME_VICE_IRQ:
chip = &ip32_crime_interrupt;
case CRIME_RE_EMPTY_E_IRQ ... CRIME_RE_IDLE_E_IRQ:
case CRIME_SOFT0_IRQ ... CRIME_SOFT2_IRQ:
set_irq_chip(irq, &crime_edge_interrupt);
break;
case CRIME_VICE_IRQ:
set_irq_chip(irq, &crime_edge_interrupt);
break;
default:
chip = &ip32_maceisa_interrupt;
set_irq_chip(irq, &ip32_maceisa_interrupt);
break;
}
set_irq_chip(irq, chip);
}
setup_irq(CRIME_MEMERR_IRQ, &memerr_irq);
setup_irq(CRIME_CPUERR_IRQ, &cpuerr_irq);
......
......@@ -22,10 +22,12 @@ enum ip32_irq_no {
* CPU interrupts are 0 ... 7
*/
CRIME_IRQ_BASE = MIPS_CPU_IRQ_BASE,
/*
* MACE
*/
MACE_VID_IN1_IRQ = MIPS_CPU_IRQ_BASE + 8,
MACE_VID_IN1_IRQ = CRIME_IRQ_BASE,
MACE_VID_IN2_IRQ,
MACE_VID_OUT_IRQ,
MACE_ETHERNET_IRQ,
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册