ide: remove CONFIG_BLK_DEV_HD_IDE config option (take 2)

* Remove CONFIG_BLK_DEV_HD hack from init_hwif_default()
  ("hda=noprobe hdb=noprobe" kernel parameters should be used
  instead if somebody wishes to use the old "hd" driver).

* Make CONFIG_BLK_DEV_HD_ONLY config option available also when
  IDE subsystem is used and update help entry.

* Remove no longer needed CONFIG_BLK_DEV_HD_IDE config option.

v2:
* Update documentation to suggest "hda=noprobe hdb=noprobe"
  instead of obsoleted "ide0=noprobe".

* Update Documentation/ide/ide.txt.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Documentation/ide/ide.txt

@@ -184,13 +184,6 @@ provided it is mounted with the default block size of 1024 (as above).
 Please pass on any feedback on any of this stuff to the maintainer,
 whose address can be found in linux/MAINTAINERS.
 
-Note that if BOTH hd.c and ide.c are configured into the kernel,
-hd.c will normally be allowed to control the primary IDE interface.
-This is useful for older hardware that may be incompatible with ide.c,
-and still allows newer hardware to run on the 2nd/3rd/4th IDE ports
-under control of ide.c.   To have ide.c also "take over" the primary
-IDE port in this situation, use the "command line" parameter:  ide0=0x1f0
-
 The IDE driver is modularized.  The high level disk/CD-ROM/tape/floppy
 drivers can always be compiled as loadable modules, the chipset drivers
 can only be compiled into the kernel, and the core code (ide.c) can be

drivers/ide/Kconfig

@@ -122,24 +122,6 @@ config BLK_DEV_IDE_SATA
 
 	  If unsure, say N.
 
-config BLK_DEV_HD_IDE
-	bool "Use old disk-only driver on primary interface"
-	depends on (X86 || SH_MPC1211)
-	---help---
-	  There are two drivers for MFM/RLL/IDE disks.  Most people use just
-	  the new enhanced driver by itself.  This option however installs the
-	  old hard disk driver to control the primary IDE/disk interface in
-	  the system, leaving the new enhanced IDE driver to take care of only
-	  the 2nd/3rd/4th IDE interfaces.  Doing this will prevent you from
-	  having an IDE/ATAPI CD-ROM or tape drive connected to the primary
-	  IDE interface.  Choosing this option may be useful for older systems
-	  which have MFM/RLL/ESDI controller+drives at the primary port
-	  address (0x1f0), along with IDE drives at the secondary/3rd/4th port
-	  addresses.
-
-	  Normally, just say N here; you will then use the new driver for all
-	  4 interfaces.
-
 config BLK_DEV_IDEDISK
 	tristate "Include IDE/ATA-2 DISK support"
 	---help---
@@ -1114,7 +1096,6 @@ endif
 
 config BLK_DEV_HD_ONLY
 	bool "Old hard disk (MFM/RLL/IDE) driver"
-	depends on BLK_DEV_IDE=n
 	help
 	  There are two drivers for MFM/RLL/IDE hard disks. Most people use
 	  the newer enhanced driver, but this old one is still around for two
@@ -1126,12 +1107,16 @@ config BLK_DEV_HD_ONLY
 	  for systems with only older MFM/RLL/ESDI drives. Choosing the old
 	  driver can save 13 KB or so of kernel memory.
 
+	  If you want to use this driver together with the new one you have
+	  to use "hda=noprobe hdb=noprobe" kernel parameters to prevent the new
+	  driver from probing the primary interface.
+
 	  If you are unsure, then just choose the Enhanced IDE/MFM/RLL driver
 	  instead of this one. For more detailed information, read the
 	  Disk-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>.
 
 config BLK_DEV_HD
-	def_bool BLK_DEV_HD_IDE || BLK_DEV_HD_ONLY
+	def_bool BLK_DEV_HD_ONLY
 
 endif # IDE

drivers/ide/ide.c

@@ -177,10 +177,6 @@ static void init_hwif_default(ide_hwif_t *hwif, unsigned int index)
 	memcpy(hwif->io_ports, hw.io_ports, sizeof(hw.io_ports));
 
 	hwif->noprobe = !hwif->io_ports[IDE_DATA_OFFSET];
-#ifdef CONFIG_BLK_DEV_HD
-	if (hwif->io_ports[IDE_DATA_OFFSET] == HD_DATA)
-		hwif->noprobe = 1;	/* may be overridden by ide_setup() */
-#endif
 }
 
 /*