[PATCH] parport: fix-up schedule_timeout() usage

Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.  Also use
human-time to jiffies units conversion functions rather than direct HZ
division to avoid rounding issues.
Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/parport/ieee1284.c

@@ -196,7 +196,7 @@ int parport_wait_peripheral(struct parport *port,
 		return 1;
 
 	/* 40ms of slow polling. */
-	deadline = jiffies + (HZ + 24) / 25;
+	deadline = jiffies + msecs_to_jiffies(40);
 	while (time_before (jiffies, deadline)) {
 		int ret;
 
@@ -205,7 +205,7 @@ int parport_wait_peripheral(struct parport *port,
 
 		/* Wait for 10ms (or until an interrupt occurs if
 		 * the handler is set) */
-		if ((ret = parport_wait_event (port, (HZ + 99) / 100)) < 0)
+		if ((ret = parport_wait_event (port, msecs_to_jiffies(10))) < 0)
 			return ret;
 
 		status = parport_read_status (port);
@@ -216,8 +216,7 @@ int parport_wait_peripheral(struct parport *port,
 			/* parport_wait_event didn't time out, but the
 			 * peripheral wasn't actually ready either.
 			 * Wait for another 10ms. */
-			__set_current_state (TASK_INTERRUPTIBLE);
-			schedule_timeout ((HZ+ 99) / 100);
+			schedule_timeout_interruptible(msecs_to_jiffies(10));
 		}
 	}
 

drivers/parport/ieee1284_ops.c

@@ -60,7 +60,7 @@ size_t parport_ieee1284_write_compat (struct parport *port,
 	parport_data_forward (port);
 	while (count < len) {
 		unsigned long expire = jiffies + dev->timeout;
-		long wait = (HZ + 99) / 100;
+		long wait = msecs_to_jiffies(10);
 		unsigned char mask = (PARPORT_STATUS_ERROR
 				      | PARPORT_STATUS_BUSY);
 		unsigned char val = (PARPORT_STATUS_ERROR
@@ -97,8 +97,7 @@ size_t parport_ieee1284_write_compat (struct parport *port,
                            our interrupt handler called. */
 			if (count && no_irq) {
 				parport_release (dev);
-				__set_current_state (TASK_INTERRUPTIBLE);
-				schedule_timeout (wait);
+				schedule_timeout_interruptible(wait);
 				parport_claim_or_block (dev);
 			}
 			else
@@ -542,13 +541,12 @@ size_t parport_ieee1284_ecp_read_data (struct parport *port,
 			/* Yield the port for a while. */
 			if (count && dev->port->irq != PARPORT_IRQ_NONE) {
 				parport_release (dev);
-				__set_current_state (TASK_INTERRUPTIBLE);
-				schedule_timeout ((HZ + 24) / 25);
+				schedule_timeout_interruptible(msecs_to_jiffies(40));
 				parport_claim_or_block (dev);
 			}
 			else
 				/* We must have the device claimed here. */
-				parport_wait_event (port, (HZ + 24) / 25);
+				parport_wait_event (port, msecs_to_jiffies(40));
 
 			/* Is there a signal pending? */
 			if (signal_pending (current))

drivers/parport/parport_pc.c

@@ -173,8 +173,7 @@ static int change_mode(struct parport *p, int m)
 				if (time_after_eq (jiffies, expire))
 					/* The FIFO is stuck. */
 					return -EBUSY;
-				__set_current_state (TASK_INTERRUPTIBLE);
-				schedule_timeout ((HZ + 99) / 100);
+				schedule_timeout_interruptible(msecs_to_jiffies(10));
 				if (signal_pending (current))
 					break;
 			}