Merge branch 'linus' into x86/asm, to resolve conflicts

Conflicts:
	tools/testing/selftests/x86/Makefile
	tools/testing/selftests/x86/run_x86_tests.sh

CREDITS

@@ -3709,6 +3709,13 @@ N: Dirk Verworner
 D: Co-author of German book ``Linux-Kernel-Programmierung''
 D: Co-founder of Berlin Linux User Group
 
+N: Andrew Victor
+E: linux@maxim.org.za
+W: http://maxim.org.za/at91_26.html
+D: First maintainer of Atmel ARM-based SoC, aka AT91
+D: Introduced support for at91rm9200, the first chip of AT91 family
+S: South Africa
+
 N: Riku Voipio
 E: riku.voipio@iki.fi
 D: Author of PCA9532 LED and Fintek f75375s hwmon driver

Documentation/devicetree/bindings/arm/omap/l3-noc.txt

@@ -6,6 +6,7 @@ provided by Arteris.
 Required properties:
 - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
                Should be "ti,omap4-l3-noc" for OMAP4 family
+               Should be "ti,omap5-l3-noc" for OMAP5 family
 	       Should be "ti,dra7-l3-noc" for DRA7 family
                Should be "ti,am4372-l3-noc" for AM43 family
 - reg:	Contains L3 register address range for each noc domain.

Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt

@@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 {
 		      80 81 68 69
 		      70 71 72 73
 		      74 75 76 77>;
-	interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+	interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
 			  "saif0", "saif1", "i2c0", "i2c1",
 			  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
 			  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";

Documentation/serial/tty.txt

@@ -198,6 +198,9 @@ TTY_IO_ERROR		If set, causes all subsequent userspace read/write
 
 TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
 
+TTY_OTHER_DONE		Device is a pty and the other side has closed and
+			all pending input processing has been completed.
+
 TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
 			smaller chunks.
 

MAINTAINERS

@@ -892,11 +892,10 @@ S:	Maintained
 F:	arch/arm/mach-alpine/
 
 ARM/ATMEL AT91RM9200 AND AT91SAM ARM ARCHITECTURES
-M:	Andrew Victor <linux@maxim.org.za>
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Alexandre Belloni <alexandre.belloni@free-electrons.com>
 M:	Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-W:	http://maxim.org.za/at91_26.html
 W:	http://www.linux4sam.org
 S:	Supported
 F:	arch/arm/mach-at91/
@@ -975,7 +974,7 @@ S:	Maintained
 ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE
 M:	Hans Ulli Kroll <ulli.kroll@googlemail.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-T:	git git://git.berlios.de/gemini-board
+T:	git git://github.com/ulli-kroll/linux.git
 S:	Maintained
 F:	arch/arm/mach-gemini/
 
@@ -990,6 +989,12 @@ F:	drivers/clocksource/timer-prima2.c
 F:	drivers/clocksource/timer-atlas7.c
 N:	[^a-z]sirf
 
+ARM/CONEXANT DIGICOLOR MACHINE SUPPORT
+M:	Baruch Siach <baruch@tkos.co.il>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+N:	digicolor
+
 ARM/EBSA110 MACHINE SUPPORT
 M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -1188,7 +1193,7 @@ ARM/MAGICIAN MACHINE SUPPORT
 M:	Philipp Zabel <philipp.zabel@gmail.com>
 S:	Maintained
 
-ARM/Marvell Armada 370 and Armada XP SOC support
+ARM/Marvell Kirkwood and Armada 370, 375, 38x, XP SOC support
 M:	Jason Cooper <jason@lakedaemon.net>
 M:	Andrew Lunn <andrew@lunn.ch>
 M:	Gregory Clement <gregory.clement@free-electrons.com>
@@ -1197,12 +1202,17 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-mvebu/
 F:	drivers/rtc/rtc-armada38x.c
+F:	arch/arm/boot/dts/armada*
+F:	arch/arm/boot/dts/kirkwood*
+
 
 ARM/Marvell Berlin SoC support
 M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-berlin/
+F:	arch/arm/boot/dts/berlin*
+
 
 ARM/Marvell Dove/MV78xx0/Orion SOC support
 M:	Jason Cooper <jason@lakedaemon.net>
@@ -1215,6 +1225,9 @@ F:	arch/arm/mach-dove/
 F:	arch/arm/mach-mv78xx0/
 F:	arch/arm/mach-orion5x/
 F:	arch/arm/plat-orion/
+F:	arch/arm/boot/dts/dove*
+F:	arch/arm/boot/dts/orion5x*
+
 
 ARM/Orion SoC/Technologic Systems TS-78xx platform support
 M:	Alexander Clouter <alex@digriz.org.uk>
@@ -1366,6 +1379,7 @@ N:	rockchip
 
 ARM/SAMSUNG EXYNOS ARM ARCHITECTURES
 M:	Kukjin Kim <kgene@kernel.org>
+M:	Krzysztof Kozlowski <k.kozlowski@samsung.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
 S:	Maintained
@@ -1439,9 +1453,10 @@ ARM/SOCFPGA ARCHITECTURE
 M:	Dinh Nguyen <dinguyen@opensource.altera.com>
 S:	Maintained
 F:	arch/arm/mach-socfpga/
+F:	arch/arm/boot/dts/socfpga*
+F:	arch/arm/configs/socfpga_defconfig
 W:	http://www.rocketboards.org
-T:	git://git.rocketboards.org/linux-socfpga.git
-T:	git://git.rocketboards.org/linux-socfpga-next.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux.git
 
 ARM/SOCFPGA CLOCK FRAMEWORK SUPPORT
 M:	Dinh Nguyen <dinguyen@opensource.altera.com>
@@ -1929,7 +1944,7 @@ S:	Maintained
 F:	drivers/net/wireless/b43legacy/
 
 BACKLIGHT CLASS/SUBSYSTEM
-M:	Jingoo Han <jg1.han@samsung.com>
+M:	Jingoo Han <jingoohan1@gmail.com>
 M:	Lee Jones <lee.jones@linaro.org>
 S:	Maintained
 F:	drivers/video/backlight/
@@ -2116,8 +2131,9 @@ S:	Supported
 F:	drivers/net/ethernet/broadcom/bnx2x/
 
 BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
-M:	Christian Daudt <bcm@fixthebug.org>
 M:	Florian Fainelli <f.fainelli@gmail.com>
+M:	Ray Jui <rjui@broadcom.com>
+M:	Scott Branden <sbranden@broadcom.com>
 L:	bcm-kernel-feedback-list@broadcom.com
 T:	git git://github.com/broadcom/mach-bcm
 S:	Maintained
@@ -2168,7 +2184,6 @@ S:	Maintained
 F:	drivers/usb/gadget/udc/bcm63xx_udc.*
 
 BROADCOM BCM7XXX ARM ARCHITECTURE
-M:	Marc Carino <marc.ceeeee@gmail.com>
 M:	Brian Norris <computersforpeace@gmail.com>
 M:	Gregory Fong <gregory.0xf0@gmail.com>
 M:	Florian Fainelli <f.fainelli@gmail.com>
@@ -3912,7 +3927,7 @@ F:	drivers/extcon/
 F:	Documentation/extcon/
 
 EXYNOS DP DRIVER
-M:	Jingoo Han <jg1.han@samsung.com>
+M:	Jingoo Han <jingoohan1@gmail.com>
 L:	dri-devel@lists.freedesktop.org
 S:	Maintained
 F:	drivers/gpu/drm/exynos/exynos_dp*
@@ -4371,11 +4386,10 @@ F:	fs/gfs2/
 F:	include/uapi/linux/gfs2_ondisk.h
 
 GIGASET ISDN DRIVERS
-M:	Hansjoerg Lipp <hjlipp@web.de>
-M:	Tilman Schmidt <tilman@imap.cc>
+M:	Paul Bolle <pebolle@tiscali.nl>
 L:	gigaset307x-common@lists.sourceforge.net
 W:	http://gigaset307x.sourceforge.net/
-S:	Maintained
+S:	Odd Fixes
 F:	Documentation/isdn/README.gigaset
 F:	drivers/isdn/gigaset/
 F:	include/uapi/linux/gigaset_dev.h
@@ -5048,7 +5062,7 @@ M:	Hal Rosenstock <hal.rosenstock@gmail.com>
 L:	linux-rdma@vger.kernel.org
 W:	http://www.openfabrics.org/
 Q:	http://patchwork.kernel.org/project/linux-rdma/list/
-T:	git git://github.com/dledford/linux.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma.git
 S:	Supported
 F:	Documentation/infiniband/
 F:	drivers/infiniband/
@@ -6953,6 +6967,17 @@ T:	git git://git.rocketboards.org/linux-socfpga-next.git
 S:	Maintained
 F:	arch/nios2/
 
+NOKIA N900 POWER SUPPLY DRIVERS
+M:	Pali Rohár <pali.rohar@gmail.com>
+S:	Maintained
+F:	include/linux/power/bq2415x_charger.h
+F:	include/linux/power/bq27x00_battery.h
+F:	include/linux/power/isp1704_charger.h
+F:	drivers/power/bq2415x_charger.c
+F:	drivers/power/bq27x00_battery.c
+F:	drivers/power/isp1704_charger.c
+F:	drivers/power/rx51_battery.c
+
 NTB DRIVER
 M:	Jon Mason <jdmason@kudzu.us>
 M:	Dave Jiang <dave.jiang@intel.com>
@@ -7541,7 +7566,7 @@ S:	Maintained
 F:	drivers/pci/host/*rcar*
 
 PCI DRIVER FOR SAMSUNG EXYNOS
-M:	Jingoo Han <jg1.han@samsung.com>
+M:	Jingoo Han <jingoohan1@gmail.com>
 L:	linux-pci@vger.kernel.org
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
@@ -7549,7 +7574,7 @@ S:	Maintained
 F:	drivers/pci/host/pci-exynos.c
 
 PCI DRIVER FOR SYNOPSIS DESIGNWARE
-M:	Jingoo Han <jg1.han@samsung.com>
+M:	Jingoo Han <jingoohan1@gmail.com>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
 F:	drivers/pci/host/*designware*
@@ -8505,7 +8530,7 @@ S:	Supported
 F:	sound/soc/samsung/
 
 SAMSUNG FRAMEBUFFER DRIVER
-M:	Jingoo Han <jg1.han@samsung.com>
+M:	Jingoo Han <jingoohan1@gmail.com>
 L:	linux-fbdev@vger.kernel.org
 S:	Maintained
 F:	drivers/video/fbdev/s3c-fb.c
@@ -8810,10 +8835,11 @@ W:	http://www.emulex.com
 S:	Supported
 F:	drivers/scsi/be2iscsi/
 
-SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER
-M:	Sathya Perla <sathya.perla@emulex.com>
-M:	Subbu Seetharaman <subbu.seetharaman@emulex.com>
-M:	Ajit Khaparde <ajit.khaparde@emulex.com>
+Emulex 10Gbps NIC BE2, BE3-R, Lancer, Skyhawk-R DRIVER
+M:	Sathya Perla <sathya.perla@avagotech.com>
+M:	Ajit Khaparde <ajit.khaparde@avagotech.com>
+M:	Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
+M:	Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
 L:	netdev@vger.kernel.org
 W:	http://www.emulex.com
 S:	Supported

Makefile

 VERSION = 4
 PATCHLEVEL = 1
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/arc/Kconfig.debug

@@ -2,19 +2,6 @@ menu "Kernel hacking"
 
 source "lib/Kconfig.debug"
 
-config EARLY_PRINTK
-	bool "Early printk" if EMBEDDED
-	default y
-	help
-	  Write kernel log output directly into the VGA buffer or to a serial
-	  port.
-
-	  This is useful for kernel debugging when your machine crashes very
-	  early before the console code is initialized. For normal operation
-	  it is not recommended because it looks ugly and doesn't cooperate
-	  with klogd/syslogd or the X server. You should normally N here,
-	  unless you want to debug such a crash.
-
 config 16KSTACKS
 	bool "Use 16Kb for kernel stacks instead of 8Kb"
 	help

arch/arc/include/asm/atomic.h

@@ -99,7 +99,7 @@ static inline void atomic_##op(int i, atomic_t *v)			\
 	atomic_ops_unlock(flags);					\
 }
 
-#define ATOMIC_OP_RETURN(op, c_op)					\
+#define ATOMIC_OP_RETURN(op, c_op, asm_op)				\
 static inline int atomic_##op##_return(int i, atomic_t *v)		\
 {									\
 	unsigned long flags;						\

arch/arc/mm/cache_arc700.c

@@ -266,7 +266,7 @@ static inline void __cache_line_loop(unsigned long paddr, unsigned long vaddr,
  * Machine specific helpers for Entire D-Cache or Per Line ops
  */
 
-static unsigned int __before_dc_op(const int op)
+static inline unsigned int __before_dc_op(const int op)
 {
 	unsigned int reg = reg;
 
@@ -284,7 +284,7 @@ static unsigned int __before_dc_op(const int op)
 	return reg;
 }
 
-static void __after_dc_op(const int op, unsigned int reg)
+static inline void __after_dc_op(const int op, unsigned int reg)
 {
 	if (op & OP_FLUSH)	/* flush / flush-n-inv both wait */
 		while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS);

arch/arm/boot/dts/am437x-sk-evm.dts

@@ -49,7 +49,7 @@
 		pinctrl-0 = <&matrix_keypad_pins>;
 
 		debounce-delay-ms = <5>;
-		col-scan-delay-us = <1500>;
+		col-scan-delay-us = <5>;
 
 		row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH		/* Bank5, pin5 */
 				&gpio5 6 GPIO_ACTIVE_HIGH>;	/* Bank5, pin6 */
@@ -473,7 +473,7 @@
 		interrupt-parent = <&gpio0>;
 		interrupts = <31 0>;
 
-		wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
 
 		touchscreen-size-x = <480>;
 		touchscreen-size-y = <272>;

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -18,6 +18,7 @@
 	aliases {
 		rtc0 = &mcp_rtc;
 		rtc1 = &tps659038_rtc;
+		rtc2 = &rtc;
 	};
 
 	memory {
@@ -83,7 +84,7 @@
 	gpio_fan: gpio_fan {
 		/* Based on 5v 500mA AFB02505HHB */
 		compatible = "gpio-fan";
-		gpios =  <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
+		gpios =  <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
 		gpio-fan,speed-map = <0     0>,
 				     <13000 1>;
 		#cooling-cells = <2>;
@@ -130,8 +131,8 @@
 
 	uart3_pins_default: uart3_pins_default {
 		pinctrl-single,pins = <
-			0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
-			0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
+			0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
+			0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
 		>;
 	};
 
@@ -455,7 +456,7 @@
 	mcp_rtc: rtc@6f {
 		compatible = "microchip,mcp7941x";
 		reg = <0x6f>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>;  /* IRQ_SYS_1N */
+		interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>;  /* IRQ_SYS_1N */
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;
@@ -478,7 +479,7 @@
 &uart3 {
 	status = "okay";
 	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-			      <&dra7_pmx_core 0x248>;
+			      <&dra7_pmx_core 0x3f8>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins_default>;

arch/arm/boot/dts/armada-375.dtsi

@@ -69,7 +69,7 @@
 		mainpll: mainpll {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <2000000000>;
+			clock-frequency = <1000000000>;
 		};
 		/* 25 MHz reference crystal */
 		refclk: oscillator {

arch/arm/boot/dts/armada-38x.dtsi

@@ -585,7 +585,7 @@
 		mainpll: mainpll {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <2000000000>;
+			clock-frequency = <1000000000>;
 		};
 
 		/* 25 MHz reference crystal */

arch/arm/boot/dts/armada-39x.dtsi

@@ -502,7 +502,7 @@
 		mainpll: mainpll {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <2000000000>;
+			clock-frequency = <1000000000>;
 		};
 	};
 };

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -105,6 +105,10 @@
 		};
 
 		internal-regs {
+			rtc@10300 {
+				/* No crystal connected to the internal RTC */
+				status = "disabled";
+			};
 			serial@12000 {
 				status = "okay";
 			};

arch/arm/boot/dts/dove-cubox.dts

@@ -87,6 +87,7 @@
 
 		/* connect xtal input to 25MHz reference */
 		clocks = <&ref25>;
+		clock-names = "xtal";
 
 		/* connect xtal input as source of pll0 and pll1 */
 		silabs,pll-source = <0 0>, <1 0>;

arch/arm/boot/dts/dra7.dtsi

@@ -911,7 +911,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
-			      <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+			      <0x4ae06014 0x4>, <0x4a003b20 0xc>,
 			      <0x4ae0c158 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -944,7 +944,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
-			      <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+			      <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
 			      <0x4a002470 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -977,7 +977,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
-			      <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+			      <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
 			      <0x4a00246c 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -1010,7 +1010,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
-			      <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+			      <0x4ae06010 0x4>, <0x4a003b08 0xc>,
 			      <0x4ae0c154 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -1203,7 +1203,7 @@
 			status = "disabled";
 		};
 
-		rtc@48838000 {
+		rtc: rtc@48838000 {
 			compatible = "ti,am3352-rtc";
 			reg = <0x48838000 0x100>;
 			interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/exynos4412-odroid-common.dtsi

@@ -9,6 +9,7 @@
 
 #include <dt-bindings/sound/samsung-i2s.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/maxim,max77686.h>
 #include "exynos4412.dtsi"
 
 / {
@@ -105,6 +106,8 @@
 
 	rtc@10070000 {
 		status = "okay";
+		clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
+		clock-names = "rtc", "rtc_src";
 	};
 
 	g2d@10800000 {

arch/arm/boot/dts/exynos5250-snow.dts

@@ -567,6 +567,7 @@
 	num-slots = <1>;
 	broken-cd;
 	cap-sdio-irq;
+	keep-power-in-suspend;
 	card-detect-delay = <200>;
 	samsung,dw-mshc-ciu-div = <3>;
 	samsung,dw-mshc-sdr-timing = <2 3>;

arch/arm/boot/dts/exynos5420-peach-pit.dts

@@ -711,6 +711,7 @@
 	num-slots = <1>;
 	broken-cd;
 	cap-sdio-irq;
+	keep-power-in-suspend;
 	card-detect-delay = <200>;
 	clock-frequency = <400000000>;
 	samsung,dw-mshc-ciu-div = <1>;

arch/arm/boot/dts/exynos5420-trip-points.dtsi

@@ -28,7 +28,7 @@ trips {
 		type = "active";
 	};
 	cpu-crit-0 {
-		temperature = <1200000>; /* millicelsius */
+		temperature = <120000>; /* millicelsius */
 		hysteresis = <0>; /* millicelsius */
 		type = "critical";
 	};

arch/arm/boot/dts/exynos5420.dtsi

@@ -536,6 +536,7 @@
 		clock-names = "dp";
 		phys = <&dp_phy>;
 		phy-names = "dp";
+		power-domains = <&disp_pd>;
 	};
 
 	mipi_phy: video-phy@10040714 {

arch/arm/boot/dts/exynos5440-trip-points.dtsi

@@ -18,7 +18,7 @@ trips {
 		type = "active";
 	};
 	cpu-crit-0 {
-		temperature = <1050000>; /* millicelsius */
+		temperature = <105000>; /* millicelsius */
 		hysteresis = <0>; /* millicelsius */
 		type = "critical";
 	};

arch/arm/boot/dts/exynos5800-peach-pi.dts

@@ -674,6 +674,7 @@
 	num-slots = <1>;
 	broken-cd;
 	cap-sdio-irq;
+	keep-power-in-suspend;
 	card-detect-delay = <200>;
 	clock-frequency = <400000000>;
 	samsung,dw-mshc-ciu-div = <1>;

arch/arm/boot/dts/imx23-olinuxino.dts

@@ -12,6 +12,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx23.dtsi"
 
 / {
@@ -93,6 +94,7 @@
 
 	ahb@80080000 {
 		usb0: usb@80080000 {
+			dr_mode = "host";
 			vbus-supply = <&reg_usb0_vbus>;
 			status = "okay";
 		};
@@ -122,7 +124,7 @@
 
 		user {
 			label = "green";
-			gpios = <&gpio2 1 1>;
+			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 		};
 	};
 };

arch/arm/boot/dts/imx25.dtsi

@@ -428,6 +428,7 @@
 
 			pwm4: pwm@53fc8000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
+				#pwm-cells = <2>;
 				reg = <0x53fc8000 0x4000>;
 				clocks = <&clks 108>, <&clks 52>;
 				clock-names = "ipg", "per";

arch/arm/boot/dts/imx28.dtsi

@@ -913,7 +913,7 @@
 					      80 81 68 69
 					      70 71 72 73
 					      74 75 76 77>;
-				interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+				interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
 						  "saif0", "saif1", "i2c0", "i2c1",
 						  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
 						  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";

arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi

@@ -31,6 +31,7 @@
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio4 15 0>;
+			enable-active-high;
 		};
 
 		reg_usb_h1_vbus: regulator@1 {
@@ -40,6 +41,7 @@
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 0 0>;
+			enable-active-high;
 		};
 	};
 

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -185,7 +185,6 @@
 &i2c3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c3>;
-	pinctrl-assert-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
 	max7310_a: gpio@30 {

arch/arm/boot/dts/omap3-n900.dts

@@ -498,6 +498,8 @@
 		DRVDD-supply = <&vmmc2>;
 		IOVDD-supply = <&vio>;
 		DVDD-supply = <&vio>;
+
+		ai3x-micbias-vg = <1>;
 	};
 
 	tlv320aic3x_aux: tlv320aic3x@19 {
@@ -509,6 +511,8 @@
 		DRVDD-supply = <&vmmc2>;
 		IOVDD-supply = <&vio>;
 		DVDD-supply = <&vio>;
+
+		ai3x-micbias-vg = <2>;
 	};
 
 	tsl2563: tsl2563@29 {

arch/arm/boot/dts/omap3.dtsi

@@ -456,6 +456,7 @@
 		};
 
 		mmu_isp: mmu@480bd400 {
+			#iommu-cells = <0>;
 			compatible = "ti,omap2-iommu";
 			reg = <0x480bd400 0x80>;
 			interrupts = <24>;
@@ -464,6 +465,7 @@
 		};
 
 		mmu_iva: mmu@5d000000 {
+			#iommu-cells = <0>;
 			compatible = "ti,omap2-iommu";
 			reg = <0x5d000000 0x80>;
 			interrupts = <28>;

arch/arm/boot/dts/omap5.dtsi

@@ -128,7 +128,7 @@
 	 * hierarchy.
 	 */
 	ocp {
-		compatible = "ti,omap4-l3-noc", "simple-bus";
+		compatible = "ti,omap5-l3-noc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;

arch/arm/boot/dts/r8a7791-koelsch.dts

@@ -545,7 +545,7 @@
 		compatible = "adi,adv7511w";
 		reg = <0x39>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";

arch/arm/boot/dts/ste-dbx5x0.dtsi

@@ -1017,23 +1017,6 @@
 			status = "disabled";
 		};
 
-		vmmci: regulator-gpio {
-			compatible = "regulator-gpio";
-
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2900000>;
-			regulator-name = "mmci-reg";
-			regulator-type = "voltage";
-
-			startup-delay-us = <100>;
-			enable-active-high;
-
-			states = <1800000 0x1
-				  2900000 0x0>;
-
-			status = "disabled";
-		};
-
 		mcde@a0350000 {
 			compatible = "stericsson,mcde";
 			reg = <0xa0350000 0x1000>, /* MCDE */

arch/arm/boot/dts/ste-href.dtsi

@@ -111,6 +111,21 @@
 			pinctrl-1 = <&i2c3_sleep_mode>;
 		};
 
+		vmmci: regulator-gpio {
+			compatible = "regulator-gpio";
+
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2900000>;
+			regulator-name = "mmci-reg";
+			regulator-type = "voltage";
+
+			startup-delay-us = <100>;
+			enable-active-high;
+
+			states = <1800000 0x1
+				  2900000 0x0>;
+		};
+
 		// External Micro SD slot
 		sdi0_per1@80126000 {
 			arm,primecell-periphid = <0x10480180>;

arch/arm/boot/dts/ste-snowball.dts

@@ -146,8 +146,21 @@
 		};
 
 		vmmci: regulator-gpio {
+			compatible = "regulator-gpio";
+
 			gpios = <&gpio7 4 0x4>;
 			enable-gpio = <&gpio6 25 0x4>;
+
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2900000>;
+			regulator-name = "mmci-reg";
+			regulator-type = "voltage";
+
+			startup-delay-us = <100>;
+			enable-active-high;
+
+			states = <1800000 0x1
+				  2900000 0x0>;
 		};
 
 		// External Micro SD slot

arch/arm/boot/dts/tegra124.dtsi

@@ -826,7 +826,7 @@
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
 			 <&tegra_car TEGRA124_CLK_USBD>;
 		clock-names = "reg", "pll_u", "utmi-pads";
-		resets = <&tegra_car 59>, <&tegra_car 22>;
+		resets = <&tegra_car 22>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
@@ -838,6 +838,7 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,has-utmi-pad-registers;
 		status = "disabled";
 	};
 
@@ -862,7 +863,7 @@
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
 			 <&tegra_car TEGRA124_CLK_USBD>;
 		clock-names = "reg", "pll_u", "utmi-pads";
-		resets = <&tegra_car 22>, <&tegra_car 22>;
+		resets = <&tegra_car 58>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;
@@ -874,7 +875,6 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
-		nvidia,has-utmi-pad-registers;
 		status = "disabled";
 	};
 
@@ -899,7 +899,7 @@
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
 			 <&tegra_car TEGRA124_CLK_USBD>;
 		clock-names = "reg", "pll_u", "utmi-pads";
-		resets = <&tegra_car 58>, <&tegra_car 22>;
+		resets = <&tegra_car 59>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";
 		nvidia,hssync-start-delay = <0>;
 		nvidia,idle-wait-delay = <17>;

arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts

@@ -191,6 +191,7 @@
 		compatible = "arm,cortex-a15-pmu";
 		interrupts = <0 68 4>,
 			     <0 69 4>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
 	oscclk6a: oscclk6a {

arch/arm/boot/dts/vexpress-v2p-ca9.dts

@@ -33,28 +33,28 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		A9_0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0>;
 			next-level-cache = <&L2>;
 		};
 
-		cpu@1 {
+		A9_1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <1>;
 			next-level-cache = <&L2>;
 		};
 
-		cpu@2 {
+		A9_2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <2>;
 			next-level-cache = <&L2>;
 		};
 
-		cpu@3 {
+		A9_3: cpu@3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <3>;
@@ -170,6 +170,7 @@
 		compatible = "arm,pl310-cache";
 		reg = <0x1e00a000 0x1000>;
 		interrupts = <0 43 4>;
+		cache-unified;
 		cache-level = <2>;
 		arm,data-latency = <1 1 1>;
 		arm,tag-latency = <1 1 1>;
@@ -181,6 +182,8 @@
 			     <0 61 4>,
 			     <0 62 4>,
 			     <0 63 4>;
+		interrupt-affinity = <&A9_0>, <&A9_1>, <&A9_2>, <&A9_3>;
+
 	};
 
 	dcc {

arch/arm/configs/multi_v7_defconfig

@@ -39,11 +39,14 @@ CONFIG_ARCH_HIP04=y
 CONFIG_ARCH_KEYSTONE=y
 CONFIG_ARCH_MESON=y
 CONFIG_ARCH_MXC=y
+CONFIG_SOC_IMX50=y
 CONFIG_SOC_IMX51=y
 CONFIG_SOC_IMX53=y
 CONFIG_SOC_IMX6Q=y
 CONFIG_SOC_IMX6SL=y
+CONFIG_SOC_IMX6SX=y
 CONFIG_SOC_VF610=y
+CONFIG_SOC_LS1021A=y
 CONFIG_ARCH_OMAP3=y
 CONFIG_ARCH_OMAP4=y
 CONFIG_SOC_OMAP5=y

arch/arm/configs/omap2plus_defconfig

@@ -393,7 +393,7 @@ CONFIG_TI_EDMA=y
 CONFIG_DMA_OMAP=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXTCON=m
-CONFIG_EXTCON_GPIO=m
+CONFIG_EXTCON_USB_GPIO=m
 CONFIG_EXTCON_PALMAS=m
 CONFIG_TI_EMIF=m
 CONFIG_PWM=y

arch/arm/include/asm/dma-iommu.h

@@ -25,7 +25,7 @@ struct dma_iommu_mapping {
 };
 
 struct dma_iommu_mapping *
-arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size);
+arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, u64 size);
 
 void arm_iommu_release_mapping(struct dma_iommu_mapping *mapping);
 

arch/arm/kernel/perf_event_cpu.c

@@ -303,12 +303,17 @@ static int probe_current_pmu(struct arm_pmu *pmu)
 
 static int of_pmu_irq_cfg(struct platform_device *pdev)
 {
-	int i;
+	int i, irq;
 	int *irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
 
 	if (!irqs)
 		return -ENOMEM;
 
+	/* Don't bother with PPIs; they're already affine */
+	irq = platform_get_irq(pdev, 0);
+	if (irq >= 0 && irq_is_percpu(irq))
+		return 0;
+
 	for (i = 0; i < pdev->num_resources; ++i) {
 		struct device_node *dn;
 		int cpu;
@@ -317,7 +322,7 @@ static int of_pmu_irq_cfg(struct platform_device *pdev)
 				      i);
 		if (!dn) {
 			pr_warn("Failed to parse %s/interrupt-affinity[%d]\n",
-				of_node_full_name(dn), i);
+				of_node_full_name(pdev->dev.of_node), i);
 			break;
 		}
 

arch/arm/mach-exynos/common.h

@@ -159,6 +159,8 @@ extern void exynos_enter_aftr(void);
 
 extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data;
 
+extern void exynos_set_delayed_reset_assertion(bool enable);
+
 extern void s5p_init_cpu(void __iomem *cpuid_addr);
 extern unsigned int samsung_rev(void);
 extern void __iomem *cpu_boot_reg_base(void);

arch/arm/mach-exynos/exynos.c

@@ -166,6 +166,33 @@ static void __init exynos_init_io(void)
 	exynos_map_io();
 }
 
+/*
+ * Set or clear the USE_DELAYED_RESET_ASSERTION option. Used by smp code
+ * and suspend.
+ *
+ * This is necessary only on Exynos4 SoCs. When system is running
+ * USE_DELAYED_RESET_ASSERTION should be set so the ARM CLK clock down
+ * feature could properly detect global idle state when secondary CPU is
+ * powered down.
+ *
+ * However this should not be set when such system is going into suspend.
+ */
+void exynos_set_delayed_reset_assertion(bool enable)
+{
+	if (of_machine_is_compatible("samsung,exynos4")) {
+		unsigned int tmp, core_id;
+
+		for (core_id = 0; core_id < num_possible_cpus(); core_id++) {
+			tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id));
+			if (enable)
+				tmp |= S5P_USE_DELAYED_RESET_ASSERTION;
+			else
+				tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION);
+			pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id));
+		}
+	}
+}
+
 /*
  * Apparently, these SoCs are not able to wake-up from suspend using
  * the PMU. Too bad. Should they suddenly become capable of such a

arch/arm/mach-exynos/platsmp.c

@@ -34,30 +34,6 @@
 
 extern void exynos4_secondary_startup(void);
 
-/*
- * Set or clear the USE_DELAYED_RESET_ASSERTION option, set on Exynos4 SoCs
- * during hot-(un)plugging CPUx.
- *
- * The feature can be cleared safely during first boot of secondary CPU.
- *
- * Exynos4 SoCs require setting USE_DELAYED_RESET_ASSERTION during powering
- * down a CPU so the CPU idle clock down feature could properly detect global
- * idle state when CPUx is off.
- */
-static void exynos_set_delayed_reset_assertion(u32 core_id, bool enable)
-{
-	if (soc_is_exynos4()) {
-		unsigned int tmp;
-
-		tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id));
-		if (enable)
-			tmp |= S5P_USE_DELAYED_RESET_ASSERTION;
-		else
-			tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION);
-		pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id));
-	}
-}
-
 #ifdef CONFIG_HOTPLUG_CPU
 static inline void cpu_leave_lowpower(u32 core_id)
 {
@@ -73,8 +49,6 @@ static inline void cpu_leave_lowpower(u32 core_id)
 	  : "=&r" (v)
 	  : "Ir" (CR_C), "Ir" (0x40)
 	  : "cc");
-
-	 exynos_set_delayed_reset_assertion(core_id, false);
 }
 
 static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
@@ -87,14 +61,6 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
 		/* Turn the CPU off on next WFI instruction. */
 		exynos_cpu_power_down(core_id);
 
-		/*
-		 * Exynos4 SoCs require setting
-		 * USE_DELAYED_RESET_ASSERTION so the CPU idle
-		 * clock down feature could properly detect
-		 * global idle state when CPUx is off.
-		 */
-		exynos_set_delayed_reset_assertion(core_id, true);
-
 		wfi();
 
 		if (pen_release == core_id) {
@@ -371,9 +337,6 @@ static int exynos_boot_secondary(unsigned int cpu, struct task_struct *idle)
 		udelay(10);
 	}
 
-	/* No harm if this is called during first boot of secondary CPU */
-	exynos_set_delayed_reset_assertion(core_id, false);
-
 	/*
 	 * now the secondary core is starting up let it run its
 	 * calibrations, then wait for it to finish
@@ -420,6 +383,8 @@ static void __init exynos_smp_prepare_cpus(unsigned int max_cpus)
 
 	exynos_sysram_init();
 
+	exynos_set_delayed_reset_assertion(true);
+
 	if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9)
 		scu_enable(scu_base_addr());
 

arch/arm/mach-exynos/pm_domains.c

@@ -188,7 +188,7 @@ static __init int exynos4_pm_init_power_domain(void)
 		args.np = np;
 		args.args_count = 0;
 		child_domain = of_genpd_get_from_provider(&args);
-		if (!child_domain)
+		if (IS_ERR(child_domain))
 			continue;
 
 		if (of_parse_phandle_with_args(np, "power-domains",
@@ -196,7 +196,7 @@ static __init int exynos4_pm_init_power_domain(void)
 			continue;
 
 		parent_domain = of_genpd_get_from_provider(&args);
-		if (!parent_domain)
+		if (IS_ERR(parent_domain))
 			continue;
 
 		if (pm_genpd_add_subdomain(parent_domain, child_domain))

arch/arm/mach-exynos/suspend.c

@@ -342,6 +342,8 @@ static void exynos_pm_enter_sleep_mode(void)
 
 static void exynos_pm_prepare(void)
 {
+	exynos_set_delayed_reset_assertion(false);
+
 	/* Set wake-up mask registers */
 	exynos_pm_set_wakeup_mask();
 
@@ -482,6 +484,7 @@ static void exynos_pm_resume(void)
 
 	/* Clear SLEEP mode set in INFORM1 */
 	pmu_raw_writel(0x0, S5P_INFORM1);
+	exynos_set_delayed_reset_assertion(true);
 }
 
 static void exynos3250_pm_resume(void)
@@ -723,8 +726,10 @@ void __init exynos_pm_init(void)
 		return;
 	}
 
-	if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL)))
+	if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) {
 		pr_warn("Outdated DT detected, suspend/resume will NOT work\n");
+		return;
+	}
 
 	pm_data = (const struct exynos_pm_data *) match->data;
 

arch/arm/mach-gemini/common.h

@@ -12,6 +12,8 @@
 #ifndef __GEMINI_COMMON_H__
 #define __GEMINI_COMMON_H__
 
+#include <linux/reboot.h>
+
 struct mtd_partition;
 
 extern void gemini_map_io(void);
@@ -26,6 +28,6 @@ extern int platform_register_pflash(unsigned int size,
 				    struct mtd_partition *parts,
 				    unsigned int nr_parts);
 
-extern void gemini_restart(char mode, const char *cmd);
+extern void gemini_restart(enum reboot_mode mode, const char *cmd);
 
 #endif /* __GEMINI_COMMON_H__ */

arch/arm/mach-gemini/reset.c

@@ -14,7 +14,9 @@
 #include <mach/hardware.h>
 #include <mach/global_reg.h>
 
-void gemini_restart(char mode, const char *cmd)
+#include "common.h"
+
+void gemini_restart(enum reboot_mode mode, const char *cmd)
 {
 	__raw_writel(RESET_GLOBAL | RESET_CPU1,
 		     IO_ADDRESS(GEMINI_GLOBAL_BASE) + GLOBAL_RESET);

arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c

 /*
- * Copyright (C) 2010 Pengutronix, Wolfram Sang <w.sang@pengutronix.de>
+ * Copyright (C) 2010 Pengutronix, Wolfram Sang <kernel@pengutronix.de>
  *
  * This program is free software; you can redistribute it and/or modify it under
  * the terms of the GNU General Public License version 2 as published by the

arch/arm/mach-omap2/omap_hwmod.c

@@ -171,6 +171,12 @@
  */
 #define LINKS_PER_OCP_IF		2
 
+/*
+ * Address offset (in bytes) between the reset control and the reset
+ * status registers: 4 bytes on OMAP4
+ */
+#define OMAP4_RST_CTRL_ST_OFFSET	4
+
 /**
  * struct omap_hwmod_soc_ops - fn ptrs for some SoC-specific operations
  * @enable_module: function to enable a module (via MODULEMODE)
@@ -3016,10 +3022,12 @@ static int _omap4_deassert_hardreset(struct omap_hwmod *oh,
 	if (ohri->st_shift)
 		pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
 		       oh->name, ohri->name);
-	return omap_prm_deassert_hardreset(ohri->rst_shift, 0,
+	return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->rst_shift,
 					   oh->clkdm->pwrdm.ptr->prcm_partition,
 					   oh->clkdm->pwrdm.ptr->prcm_offs,
-					   oh->prcm.omap4.rstctrl_offs, 0);
+					   oh->prcm.omap4.rstctrl_offs,
+					   oh->prcm.omap4.rstctrl_offs +
+					   OMAP4_RST_CTRL_ST_OFFSET);
 }
 
 /**
@@ -3047,27 +3055,6 @@ static int _omap4_is_hardreset_asserted(struct omap_hwmod *oh,
 					      oh->prcm.omap4.rstctrl_offs);
 }
 
-/**
- * _am33xx_assert_hardreset - call AM33XX PRM hardreset fn with hwmod args
- * @oh: struct omap_hwmod * to assert hardreset
- * @ohri: hardreset line data
- *
- * Call am33xx_prminst_assert_hardreset() with parameters extracted
- * from the hwmod @oh and the hardreset line data @ohri.  Only
- * intended for use as an soc_ops function pointer.  Passes along the
- * return value from am33xx_prminst_assert_hardreset().  XXX This
- * function is scheduled for removal when the PRM code is moved into
- * drivers/.
- */
-static int _am33xx_assert_hardreset(struct omap_hwmod *oh,
-				   struct omap_hwmod_rst_info *ohri)
-
-{
-	return omap_prm_assert_hardreset(ohri->rst_shift, 0,
-					 oh->clkdm->pwrdm.ptr->prcm_offs,
-					 oh->prcm.omap4.rstctrl_offs);
-}
-
 /**
  * _am33xx_deassert_hardreset - call AM33XX PRM hardreset fn with hwmod args
  * @oh: struct omap_hwmod * to deassert hardreset
@@ -3083,32 +3070,13 @@ static int _am33xx_assert_hardreset(struct omap_hwmod *oh,
 static int _am33xx_deassert_hardreset(struct omap_hwmod *oh,
 				     struct omap_hwmod_rst_info *ohri)
 {
-	return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->st_shift, 0,
+	return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->st_shift,
+					   oh->clkdm->pwrdm.ptr->prcm_partition,
 					   oh->clkdm->pwrdm.ptr->prcm_offs,
 					   oh->prcm.omap4.rstctrl_offs,
 					   oh->prcm.omap4.rstst_offs);
 }
 
-/**
- * _am33xx_is_hardreset_asserted - call AM33XX PRM hardreset fn with hwmod args
- * @oh: struct omap_hwmod * to test hardreset
- * @ohri: hardreset line data
- *
- * Call am33xx_prminst_is_hardreset_asserted() with parameters
- * extracted from the hwmod @oh and the hardreset line data @ohri.
- * Only intended for use as an soc_ops function pointer.  Passes along
- * the return value from am33xx_prminst_is_hardreset_asserted().  XXX
- * This function is scheduled for removal when the PRM code is moved
- * into drivers/.
- */
-static int _am33xx_is_hardreset_asserted(struct omap_hwmod *oh,
-					struct omap_hwmod_rst_info *ohri)
-{
-	return omap_prm_is_hardreset_asserted(ohri->rst_shift, 0,
-					      oh->clkdm->pwrdm.ptr->prcm_offs,
-					      oh->prcm.omap4.rstctrl_offs);
-}
-
 /* Public functions */
 
 u32 omap_hwmod_read(struct omap_hwmod *oh, u16 reg_offs)
@@ -3908,21 +3876,13 @@ void __init omap_hwmod_init(void)
 		soc_ops.init_clkdm = _init_clkdm;
 		soc_ops.update_context_lost = _omap4_update_context_lost;
 		soc_ops.get_context_lost = _omap4_get_context_lost;
-	} else if (soc_is_am43xx()) {
+	} else if (cpu_is_ti816x() || soc_is_am33xx() || soc_is_am43xx()) {
 		soc_ops.enable_module = _omap4_enable_module;
 		soc_ops.disable_module = _omap4_disable_module;
 		soc_ops.wait_target_ready = _omap4_wait_target_ready;
 		soc_ops.assert_hardreset = _omap4_assert_hardreset;
-		soc_ops.deassert_hardreset = _omap4_deassert_hardreset;
-		soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
-		soc_ops.init_clkdm = _init_clkdm;
-	} else if (cpu_is_ti816x() || soc_is_am33xx()) {
-		soc_ops.enable_module = _omap4_enable_module;
-		soc_ops.disable_module = _omap4_disable_module;
-		soc_ops.wait_target_ready = _omap4_wait_target_ready;
-		soc_ops.assert_hardreset = _am33xx_assert_hardreset;
 		soc_ops.deassert_hardreset = _am33xx_deassert_hardreset;
-		soc_ops.is_hardreset_asserted = _am33xx_is_hardreset_asserted;
+		soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
 		soc_ops.init_clkdm = _init_clkdm;
 	} else {
 		WARN(1, "omap_hwmod: unknown SoC type\n");

arch/arm/mach-omap2/omap_hwmod_43xx_data.c

@@ -544,6 +544,44 @@ static struct omap_hwmod am43xx_hdq1w_hwmod = {
 	},
 };
 
+static struct omap_hwmod_class_sysconfig am43xx_vpfe_sysc = {
+	.rev_offs       = 0x0,
+	.sysc_offs      = 0x104,
+	.sysc_flags     = SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE,
+	.idlemodes      = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+				MSTANDBY_FORCE | MSTANDBY_SMART | MSTANDBY_NO),
+	.sysc_fields    = &omap_hwmod_sysc_type2,
+};
+
+static struct omap_hwmod_class am43xx_vpfe_hwmod_class = {
+	.name           = "vpfe",
+	.sysc           = &am43xx_vpfe_sysc,
+};
+
+static struct omap_hwmod am43xx_vpfe0_hwmod = {
+	.name           = "vpfe0",
+	.class          = &am43xx_vpfe_hwmod_class,
+	.clkdm_name     = "l3s_clkdm",
+	.prcm           = {
+		.omap4  = {
+			.modulemode     = MODULEMODE_SWCTRL,
+			.clkctrl_offs   = AM43XX_CM_PER_VPFE0_CLKCTRL_OFFSET,
+		},
+	},
+};
+
+static struct omap_hwmod am43xx_vpfe1_hwmod = {
+	.name           = "vpfe1",
+	.class          = &am43xx_vpfe_hwmod_class,
+	.clkdm_name     = "l3s_clkdm",
+	.prcm           = {
+		.omap4  = {
+			.modulemode     = MODULEMODE_SWCTRL,
+			.clkctrl_offs   = AM43XX_CM_PER_VPFE1_CLKCTRL_OFFSET,
+		},
+	},
+};
+
 /* Interfaces */
 static struct omap_hwmod_ocp_if am43xx_l3_main__l4_hs = {
 	.master		= &am33xx_l3_main_hwmod,
@@ -825,6 +863,34 @@ static struct omap_hwmod_ocp_if am43xx_l4_ls__hdq1w = {
 	.user           = OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+static struct omap_hwmod_ocp_if am43xx_l3__vpfe0 = {
+	.master         = &am43xx_vpfe0_hwmod,
+	.slave          = &am33xx_l3_main_hwmod,
+	.clk            = "l3_gclk",
+	.user           = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod_ocp_if am43xx_l3__vpfe1 = {
+	.master         = &am43xx_vpfe1_hwmod,
+	.slave          = &am33xx_l3_main_hwmod,
+	.clk            = "l3_gclk",
+	.user           = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod_ocp_if am43xx_l4_ls__vpfe0 = {
+	.master         = &am33xx_l4_ls_hwmod,
+	.slave          = &am43xx_vpfe0_hwmod,
+	.clk            = "l4ls_gclk",
+	.user           = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod_ocp_if am43xx_l4_ls__vpfe1 = {
+	.master         = &am33xx_l4_ls_hwmod,
+	.slave          = &am43xx_vpfe1_hwmod,
+	.clk            = "l4ls_gclk",
+	.user           = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
 	&am33xx_l4_wkup__synctimer,
 	&am43xx_l4_ls__timer8,
@@ -925,6 +991,10 @@ static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
 	&am43xx_l4_ls__dss_dispc,
 	&am43xx_l4_ls__dss_rfbi,
 	&am43xx_l4_ls__hdq1w,
+	&am43xx_l3__vpfe0,
+	&am43xx_l3__vpfe1,
+	&am43xx_l4_ls__vpfe0,
+	&am43xx_l4_ls__vpfe1,
 	NULL,
 };
 

arch/arm/mach-omap2/prcm43xx.h

@@ -144,5 +144,6 @@
 #define AM43XX_CM_PER_USBPHYOCP2SCP1_CLKCTRL_OFFSET	0x05C0
 #define AM43XX_CM_PER_DSS_CLKCTRL_OFFSET		0x0a20
 #define AM43XX_CM_PER_HDQ1W_CLKCTRL_OFFSET		0x04a0
-
+#define AM43XX_CM_PER_VPFE0_CLKCTRL_OFFSET		0x0068
+#define AM43XX_CM_PER_VPFE1_CLKCTRL_OFFSET		0x0070
 #endif

arch/arm/mach-omap2/prm-regbits-34xx.h

@@ -112,6 +112,7 @@
 #define OMAP3430_VC_CMD_ONLP_SHIFT			16
 #define OMAP3430_VC_CMD_RET_SHIFT			8
 #define OMAP3430_VC_CMD_OFF_SHIFT			0
+#define OMAP3430_SREN_MASK				(1 << 4)
 #define OMAP3430_HSEN_MASK				(1 << 3)
 #define OMAP3430_MCODE_MASK				(0x7 << 0)
 #define OMAP3430_VALID_MASK				(1 << 24)

arch/arm/mach-omap2/prm-regbits-44xx.h

@@ -35,6 +35,7 @@
 #define OMAP4430_GLOBAL_WARM_SW_RST_SHIFT				1
 #define OMAP4430_GLOBAL_WUEN_MASK					(1 << 16)
 #define OMAP4430_HSMCODE_MASK						(0x7 << 0)
+#define OMAP4430_SRMODEEN_MASK						(1 << 4)
 #define OMAP4430_HSMODEEN_MASK						(1 << 3)
 #define OMAP4430_HSSCLL_SHIFT						24
 #define OMAP4430_ICEPICK_RST_SHIFT					9

arch/arm/mach-omap2/prminst44xx.c

@@ -87,12 +87,6 @@ u32 omap4_prminst_rmw_inst_reg_bits(u32 mask, u32 bits, u8 part, s16 inst,
 	return v;
 }
 
-/*
- * Address offset (in bytes) between the reset control and the reset
- * status registers: 4 bytes on OMAP4
- */
-#define OMAP4_RST_CTRL_ST_OFFSET		4
-
 /**
  * omap4_prminst_is_hardreset_asserted - read the HW reset line state of
  * submodules contained in the hwmod module
@@ -141,11 +135,11 @@ int omap4_prminst_assert_hardreset(u8 shift, u8 part, s16 inst,
  * omap4_prminst_deassert_hardreset - deassert a submodule hardreset line and
  * wait
  * @shift: register bit shift corresponding to the reset line to deassert
- * @st_shift: status bit offset, not used for OMAP4+
+ * @st_shift: status bit offset corresponding to the reset line
  * @part: PRM partition
  * @inst: PRM instance offset
  * @rstctrl_offs: reset register offset
- * @st_offs: reset status register offset, not used for OMAP4+
+ * @rstst_offs: reset status register offset
  *
  * Some IPs like dsp, ipu or iva contain processors that require an HW
  * reset line to be asserted / deasserted in order to fully enable the
@@ -157,11 +151,11 @@ int omap4_prminst_assert_hardreset(u8 shift, u8 part, s16 inst,
  * of reset, or -EBUSY if the submodule did not exit reset promptly.
  */
 int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
-				     u16 rstctrl_offs, u16 st_offs)
+				     u16 rstctrl_offs, u16 rstst_offs)
 {
 	int c;
 	u32 mask = 1 << shift;
-	u16 rstst_offs = rstctrl_offs + OMAP4_RST_CTRL_ST_OFFSET;
+	u32 st_mask = 1 << st_shift;
 
 	/* Check the current status to avoid de-asserting the line twice */
 	if (omap4_prminst_is_hardreset_asserted(shift, part, inst,
@@ -169,13 +163,13 @@ int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
 		return -EEXIST;
 
 	/* Clear the reset status by writing 1 to the status bit */
-	omap4_prminst_rmw_inst_reg_bits(0xffffffff, mask, part, inst,
+	omap4_prminst_rmw_inst_reg_bits(0xffffffff, st_mask, part, inst,
 					rstst_offs);
 	/* de-assert the reset control line */
 	omap4_prminst_rmw_inst_reg_bits(mask, 0, part, inst, rstctrl_offs);
 	/* wait the status to be set */
-	omap_test_timeout(omap4_prminst_is_hardreset_asserted(shift, part, inst,
-							      rstst_offs),
+	omap_test_timeout(omap4_prminst_is_hardreset_asserted(st_shift, part,
+							      inst, rstst_offs),
 			  MAX_MODULE_HARDRESET_WAIT, c);
 
 	return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;

arch/arm/mach-omap2/timer.c

@@ -298,14 +298,11 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer,
 	if (IS_ERR(src))
 		return PTR_ERR(src);
 
-	if (clk_get_parent(timer->fclk) != src) {
-		r = clk_set_parent(timer->fclk, src);
-		if (r < 0) {
-			pr_warn("%s: %s cannot set source\n", __func__,
-				oh->name);
-			clk_put(src);
-			return r;
-		}
+	r = clk_set_parent(timer->fclk, src);
+	if (r < 0) {
+		pr_warn("%s: %s cannot set source\n", __func__, oh->name);
+		clk_put(src);
+		return r;
 	}
 
 	clk_put(src);

arch/arm/mach-omap2/vc.c

@@ -316,7 +316,8 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
 	 * idle. And we can also scale voltages to zero for off-idle.
 	 * Note that no actual voltage scaling during off-idle will
 	 * happen unless the board specific twl4030 PMIC scripts are
-	 * loaded.
+	 * loaded. See also omap_vc_i2c_init for comments regarding
+	 * erratum i531.
 	 */
 	val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
 	if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
@@ -704,9 +705,16 @@ static void __init omap_vc_i2c_init(struct voltagedomain *voltdm)
 		return;
 	}
 
+	/*
+	 * Note that for omap3 OMAP3430_SREN_MASK clears SREN to work around
+	 * erratum i531 "Extra Power Consumed When Repeated Start Operation
+	 * Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)".
+	 * Otherwise I2C4 eventually leads into about 23mW extra power being
+	 * consumed even during off idle using VMODE.
+	 */
 	i2c_high_speed = voltdm->pmic->i2c_high_speed;
 	if (i2c_high_speed)
-		voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
+		voltdm->rmw(vc->common->i2c_cfg_clear_mask,
 			    vc->common->i2c_cfg_hsen_mask,
 			    vc->common->i2c_cfg_reg);
 

arch/arm/mach-omap2/vc.h

@@ -34,6 +34,7 @@ struct voltagedomain;
  * @cmd_ret_shift: RET field shift in PRM_VC_CMD_VAL_* register
  * @cmd_off_shift: OFF field shift in PRM_VC_CMD_VAL_* register
  * @i2c_cfg_reg: I2C configuration register offset
+ * @i2c_cfg_clear_mask: high-speed mode bit clear mask in I2C config register
  * @i2c_cfg_hsen_mask: high-speed mode bit field mask in I2C config register
  * @i2c_mcode_mask: MCODE field mask for I2C config register
  *
@@ -52,6 +53,7 @@ struct omap_vc_common {
 	u8 cmd_ret_shift;
 	u8 cmd_off_shift;
 	u8 i2c_cfg_reg;
+	u8 i2c_cfg_clear_mask;
 	u8 i2c_cfg_hsen_mask;
 	u8 i2c_mcode_mask;
 };

arch/arm/mach-omap2/vc3xxx_data.c

@@ -40,6 +40,7 @@ static struct omap_vc_common omap3_vc_common = {
 	.cmd_onlp_shift	 = OMAP3430_VC_CMD_ONLP_SHIFT,
 	.cmd_ret_shift	 = OMAP3430_VC_CMD_RET_SHIFT,
 	.cmd_off_shift	 = OMAP3430_VC_CMD_OFF_SHIFT,
+	.i2c_cfg_clear_mask = OMAP3430_SREN_MASK | OMAP3430_HSEN_MASK,
 	.i2c_cfg_hsen_mask = OMAP3430_HSEN_MASK,
 	.i2c_cfg_reg	 = OMAP3_PRM_VC_I2C_CFG_OFFSET,
 	.i2c_mcode_mask	 = OMAP3430_MCODE_MASK,

arch/arm/mach-omap2/vc44xx_data.c

@@ -42,6 +42,7 @@ static const struct omap_vc_common omap4_vc_common = {
 	.cmd_ret_shift = OMAP4430_RET_SHIFT,
 	.cmd_off_shift = OMAP4430_OFF_SHIFT,
 	.i2c_cfg_reg = OMAP4_PRM_VC_CFG_I2C_MODE_OFFSET,
+	.i2c_cfg_clear_mask = OMAP4430_SRMODEEN_MASK | OMAP4430_HSMODEEN_MASK,
 	.i2c_cfg_hsen_mask = OMAP4430_HSMODEEN_MASK,
 	.i2c_mcode_mask	 = OMAP4430_HSMCODE_MASK,
 };

arch/arm/mach-pxa/Kconfig

@@ -691,4 +691,13 @@ config SHARPSL_PM_MAX1111
 config PXA310_ULPI
 	bool
 
+config PXA_SYSTEMS_CPLDS
+	tristate "Motherboard cplds"
+	default ARCH_LUBBOCK || MACH_MAINSTONE
+	help
+	  This driver supports the Lubbock and Mainstone multifunction chip
+	  found on the pxa25x development platform system (Lubbock) and pxa27x
+	  development platform system (Mainstone). This IO board supports the
+	  interrupts handling, ethernet controller, flash chips, etc ...
+
 endif

arch/arm/mach-pxa/Makefile

@@ -90,4 +90,5 @@ obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR)	+= raumfeld.o
 obj-$(CONFIG_MACH_RAUMFELD_SPEAKER)	+= raumfeld.o
 obj-$(CONFIG_MACH_ZIPIT2)	+= z2.o
 
+obj-$(CONFIG_PXA_SYSTEMS_CPLDS)	+= pxa_cplds_irqs.o
 obj-$(CONFIG_TOSA_BT)		+= tosa-bt.o

arch/arm/mach-pxa/include/mach/lubbock.h

@@ -37,7 +37,9 @@
 #define LUB_GP			__LUB_REG(LUBBOCK_FPGA_PHYS + 0x100)
 
 /* Board specific IRQs */
-#define LUBBOCK_IRQ(x)		(IRQ_BOARD_START + (x))
+#define LUBBOCK_NR_IRQS		IRQ_BOARD_START
+
+#define LUBBOCK_IRQ(x)		(LUBBOCK_NR_IRQS + (x))
 #define LUBBOCK_SD_IRQ		LUBBOCK_IRQ(0)
 #define LUBBOCK_SA1111_IRQ	LUBBOCK_IRQ(1)
 #define LUBBOCK_USB_IRQ		LUBBOCK_IRQ(2)  /* usb connect */
@@ -47,8 +49,7 @@
 #define LUBBOCK_USB_DISC_IRQ	LUBBOCK_IRQ(6)  /* usb disconnect */
 #define LUBBOCK_LAST_IRQ	LUBBOCK_IRQ(6)
 
-#define LUBBOCK_SA1111_IRQ_BASE	(IRQ_BOARD_START + 16)
-#define LUBBOCK_NR_IRQS		(IRQ_BOARD_START + 16 + 55)
+#define LUBBOCK_SA1111_IRQ_BASE	(LUBBOCK_NR_IRQS + 32)
 
 #ifndef __ASSEMBLY__
 extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set);

arch/arm/mach-pxa/include/mach/mainstone.h

@@ -120,7 +120,9 @@
 #define MST_PCMCIA_PWR_VCC_50   0x4	   /* voltage VCC = 5.0V */
 
 /* board specific IRQs */
-#define MAINSTONE_IRQ(x)	(IRQ_BOARD_START + (x))
+#define MAINSTONE_NR_IRQS	IRQ_BOARD_START
+
+#define MAINSTONE_IRQ(x)	(MAINSTONE_NR_IRQS + (x))
 #define MAINSTONE_MMC_IRQ	MAINSTONE_IRQ(0)
 #define MAINSTONE_USIM_IRQ	MAINSTONE_IRQ(1)
 #define MAINSTONE_USBC_IRQ	MAINSTONE_IRQ(2)
@@ -136,6 +138,4 @@
 #define MAINSTONE_S1_STSCHG_IRQ	MAINSTONE_IRQ(14)
 #define MAINSTONE_S1_IRQ	MAINSTONE_IRQ(15)
 
-#define MAINSTONE_NR_IRQS	(IRQ_BOARD_START + 16)
-
 #endif

arch/arm/mach-pxa/lubbock.c

@@ -12,6 +12,7 @@
  *  published by the Free Software Foundation.
  */
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -123,84 +124,6 @@ void lubbock_set_misc_wr(unsigned int mask, unsigned int set)
 }
 EXPORT_SYMBOL(lubbock_set_misc_wr);
 
-static unsigned long lubbock_irq_enabled;
-
-static void lubbock_mask_irq(struct irq_data *d)
-{
-	int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
-	LUB_IRQ_MASK_EN = (lubbock_irq_enabled &= ~(1 << lubbock_irq));
-}
-
-static void lubbock_unmask_irq(struct irq_data *d)
-{
-	int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
-	/* the irq can be acknowledged only if deasserted, so it's done here */
-	LUB_IRQ_SET_CLR &= ~(1 << lubbock_irq);
-	LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
-}
-
-static struct irq_chip lubbock_irq_chip = {
-	.name		= "FPGA",
-	.irq_ack	= lubbock_mask_irq,
-	.irq_mask	= lubbock_mask_irq,
-	.irq_unmask	= lubbock_unmask_irq,
-};
-
-static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
-	do {
-		/* clear our parent irq */
-		desc->irq_data.chip->irq_ack(&desc->irq_data);
-		if (likely(pending)) {
-			irq = LUBBOCK_IRQ(0) + __ffs(pending);
-			generic_handle_irq(irq);
-		}
-		pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
-	} while (pending);
-}
-
-static void __init lubbock_init_irq(void)
-{
-	int irq;
-
-	pxa25x_init_irq();
-
-	/* setup extra lubbock irqs */
-	for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
-		irq_set_chip_and_handler(irq, &lubbock_irq_chip,
-					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-	}
-
-	irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), lubbock_irq_handler);
-	irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING);
-}
-
-#ifdef CONFIG_PM
-
-static void lubbock_irq_resume(void)
-{
-	LUB_IRQ_MASK_EN = lubbock_irq_enabled;
-}
-
-static struct syscore_ops lubbock_irq_syscore_ops = {
-	.resume = lubbock_irq_resume,
-};
-
-static int __init lubbock_irq_device_init(void)
-{
-	if (machine_is_lubbock()) {
-		register_syscore_ops(&lubbock_irq_syscore_ops);
-		return 0;
-	}
-	return -ENODEV;
-}
-
-device_initcall(lubbock_irq_device_init);
-
-#endif
-
 static int lubbock_udc_is_connected(void)
 {
 	return (LUB_MISC_RD & (1 << 9)) == 0;
@@ -383,11 +306,38 @@ static struct platform_device lubbock_flash_device[2] = {
 	},
 };
 
+static struct resource lubbock_cplds_resources[] = {
+	[0] = {
+		.start	= LUBBOCK_FPGA_PHYS + 0xc0,
+		.end	= LUBBOCK_FPGA_PHYS + 0xe0 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= PXA_GPIO_TO_IRQ(0),
+		.end	= PXA_GPIO_TO_IRQ(0),
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
+	},
+	[2] = {
+		.start	= LUBBOCK_IRQ(0),
+		.end	= LUBBOCK_IRQ(6),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device lubbock_cplds_device = {
+	.name		= "pxa_cplds_irqs",
+	.id		= -1,
+	.resource	= &lubbock_cplds_resources[0],
+	.num_resources	= 3,
+};
+
+
 static struct platform_device *devices[] __initdata = {
 	&sa1111_device,
 	&smc91x_device,
 	&lubbock_flash_device[0],
 	&lubbock_flash_device[1],
+	&lubbock_cplds_device,
 };
 
 static struct pxafb_mode_info sharp_lm8v31_mode = {
@@ -648,7 +598,7 @@ MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
 	/* Maintainer: MontaVista Software Inc. */
 	.map_io		= lubbock_map_io,
 	.nr_irqs	= LUBBOCK_NR_IRQS,
-	.init_irq	= lubbock_init_irq,
+	.init_irq	= pxa25x_init_irq,
 	.handle_irq	= pxa25x_handle_irq,
 	.init_time	= pxa_timer_init,
 	.init_machine	= lubbock_init,

arch/arm/mach-pxa/mainstone.c

@@ -13,6 +13,7 @@
  *  published by the Free Software Foundation.
  */
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/syscore_ops.h>
@@ -122,92 +123,6 @@ static unsigned long mainstone_pin_config[] = {
 	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
 };
 
-static unsigned long mainstone_irq_enabled;
-
-static void mainstone_mask_irq(struct irq_data *d)
-{
-	int mainstone_irq = (d->irq - MAINSTONE_IRQ(0));
-	MST_INTMSKENA = (mainstone_irq_enabled &= ~(1 << mainstone_irq));
-}
-
-static void mainstone_unmask_irq(struct irq_data *d)
-{
-	int mainstone_irq = (d->irq - MAINSTONE_IRQ(0));
-	/* the irq can be acknowledged only if deasserted, so it's done here */
-	MST_INTSETCLR &= ~(1 << mainstone_irq);
-	MST_INTMSKENA = (mainstone_irq_enabled |= (1 << mainstone_irq));
-}
-
-static struct irq_chip mainstone_irq_chip = {
-	.name		= "FPGA",
-	.irq_ack	= mainstone_mask_irq,
-	.irq_mask	= mainstone_mask_irq,
-	.irq_unmask	= mainstone_unmask_irq,
-};
-
-static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	unsigned long pending = MST_INTSETCLR & mainstone_irq_enabled;
-	do {
-		/* clear useless edge notification */
-		desc->irq_data.chip->irq_ack(&desc->irq_data);
-		if (likely(pending)) {
-			irq = MAINSTONE_IRQ(0) + __ffs(pending);
-			generic_handle_irq(irq);
-		}
-		pending = MST_INTSETCLR & mainstone_irq_enabled;
-	} while (pending);
-}
-
-static void __init mainstone_init_irq(void)
-{
-	int irq;
-
-	pxa27x_init_irq();
-
-	/* setup extra Mainstone irqs */
-	for(irq = MAINSTONE_IRQ(0); irq <= MAINSTONE_IRQ(15); irq++) {
-		irq_set_chip_and_handler(irq, &mainstone_irq_chip,
-					 handle_level_irq);
-		if (irq == MAINSTONE_IRQ(10) || irq == MAINSTONE_IRQ(14))
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE | IRQF_NOAUTOEN);
-		else
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-	}
-	set_irq_flags(MAINSTONE_IRQ(8), 0);
-	set_irq_flags(MAINSTONE_IRQ(12), 0);
-
-	MST_INTMSKENA = 0;
-	MST_INTSETCLR = 0;
-
-	irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), mainstone_irq_handler);
-	irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING);
-}
-
-#ifdef CONFIG_PM
-
-static void mainstone_irq_resume(void)
-{
-	MST_INTMSKENA = mainstone_irq_enabled;
-}
-
-static struct syscore_ops mainstone_irq_syscore_ops = {
-	.resume = mainstone_irq_resume,
-};
-
-static int __init mainstone_irq_device_init(void)
-{
-	if (machine_is_mainstone())
-		register_syscore_ops(&mainstone_irq_syscore_ops);
-
-	return 0;
-}
-
-device_initcall(mainstone_irq_device_init);
-
-#endif
-
-
 static struct resource smc91x_resources[] = {
 	[0] = {
 		.start	= (MST_ETH_PHYS + 0x300),
@@ -487,11 +402,37 @@ static struct platform_device mst_gpio_keys_device = {
 	},
 };
 
+static struct resource mst_cplds_resources[] = {
+	[0] = {
+		.start	= MST_FPGA_PHYS + 0xc0,
+		.end	= MST_FPGA_PHYS + 0xe0 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= PXA_GPIO_TO_IRQ(0),
+		.end	= PXA_GPIO_TO_IRQ(0),
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
+	},
+	[2] = {
+		.start	= MAINSTONE_IRQ(0),
+		.end	= MAINSTONE_IRQ(15),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device mst_cplds_device = {
+	.name		= "pxa_cplds_irqs",
+	.id		= -1,
+	.resource	= &mst_cplds_resources[0],
+	.num_resources	= 3,
+};
+
 static struct platform_device *platform_devices[] __initdata = {
 	&smc91x_device,
 	&mst_flash_device[0],
 	&mst_flash_device[1],
 	&mst_gpio_keys_device,
+	&mst_cplds_device,
 };
 
 static struct pxaohci_platform_data mainstone_ohci_platform_data = {
@@ -718,7 +659,7 @@ MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)")
 	.atag_offset	= 0x100,	/* BLOB boot parameter setting */
 	.map_io		= mainstone_map_io,
 	.nr_irqs	= MAINSTONE_NR_IRQS,
-	.init_irq	= mainstone_init_irq,
+	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
 	.init_time	= pxa_timer_init,
 	.init_machine	= mainstone_init,

arch/arm/mach-pxa/pxa_cplds_irqs.c

+/*
+ * Intel Reference Systems cplds
+ *
+ * Copyright (C) 2014 Robert Jarzmik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Cplds motherboard driver, supporting lubbock and mainstone SoC board.
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+
+#define FPGA_IRQ_MASK_EN 0x0
+#define FPGA_IRQ_SET_CLR 0x10
+
+#define CPLDS_NB_IRQ	32
+
+struct cplds {
+	void __iomem *base;
+	int irq;
+	unsigned int irq_mask;
+	struct gpio_desc *gpio0;
+	struct irq_domain *irqdomain;
+};
+
+static irqreturn_t cplds_irq_handler(int in_irq, void *d)
+{
+	struct cplds *fpga = d;
+	unsigned long pending;
+	unsigned int bit;
+
+	pending = readl(fpga->base + FPGA_IRQ_SET_CLR) & fpga->irq_mask;
+	for_each_set_bit(bit, &pending, CPLDS_NB_IRQ)
+		generic_handle_irq(irq_find_mapping(fpga->irqdomain, bit));
+
+	return IRQ_HANDLED;
+}
+
+static void cplds_irq_mask_ack(struct irq_data *d)
+{
+	struct cplds *fpga = irq_data_get_irq_chip_data(d);
+	unsigned int cplds_irq = irqd_to_hwirq(d);
+	unsigned int set, bit = BIT(cplds_irq);
+
+	fpga->irq_mask &= ~bit;
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+	set = readl(fpga->base + FPGA_IRQ_SET_CLR);
+	writel(set & ~bit, fpga->base + FPGA_IRQ_SET_CLR);
+}
+
+static void cplds_irq_unmask(struct irq_data *d)
+{
+	struct cplds *fpga = irq_data_get_irq_chip_data(d);
+	unsigned int cplds_irq = irqd_to_hwirq(d);
+	unsigned int bit = BIT(cplds_irq);
+
+	fpga->irq_mask |= bit;
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+}
+
+static struct irq_chip cplds_irq_chip = {
+	.name		= "pxa_cplds",
+	.irq_mask_ack	= cplds_irq_mask_ack,
+	.irq_unmask	= cplds_irq_unmask,
+	.flags		= IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE,
+};
+
+static int cplds_irq_domain_map(struct irq_domain *d, unsigned int irq,
+				   irq_hw_number_t hwirq)
+{
+	struct cplds *fpga = d->host_data;
+
+	irq_set_chip_and_handler(irq, &cplds_irq_chip, handle_level_irq);
+	irq_set_chip_data(irq, fpga);
+
+	return 0;
+}
+
+static const struct irq_domain_ops cplds_irq_domain_ops = {
+	.xlate = irq_domain_xlate_twocell,
+	.map = cplds_irq_domain_map,
+};
+
+static int cplds_resume(struct platform_device *pdev)
+{
+	struct cplds *fpga = platform_get_drvdata(pdev);
+
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+
+	return 0;
+}
+
+static int cplds_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct cplds *fpga;
+	int ret;
+	unsigned int base_irq = 0;
+	unsigned long irqflags = 0;
+
+	fpga = devm_kzalloc(&pdev->dev, sizeof(*fpga), GFP_KERNEL);
+	if (!fpga)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (res) {
+		fpga->irq = (unsigned int)res->start;
+		irqflags = res->flags;
+	}
+	if (!fpga->irq)
+		return -ENODEV;
+
+	base_irq = platform_get_irq(pdev, 1);
+	if (base_irq < 0)
+		base_irq = 0;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	fpga->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(fpga->base))
+		return PTR_ERR(fpga->base);
+
+	platform_set_drvdata(pdev, fpga);
+
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+	writel(0, fpga->base + FPGA_IRQ_SET_CLR);
+
+	ret = devm_request_irq(&pdev->dev, fpga->irq, cplds_irq_handler,
+			       irqflags, dev_name(&pdev->dev), fpga);
+	if (ret == -ENOSYS)
+		return -EPROBE_DEFER;
+
+	if (ret) {
+		dev_err(&pdev->dev, "couldn't request main irq%d: %d\n",
+			fpga->irq, ret);
+		return ret;
+	}
+
+	irq_set_irq_wake(fpga->irq, 1);
+	fpga->irqdomain = irq_domain_add_linear(pdev->dev.of_node,
+					       CPLDS_NB_IRQ,
+					       &cplds_irq_domain_ops, fpga);
+	if (!fpga->irqdomain)
+		return -ENODEV;
+
+	if (base_irq) {
+		ret = irq_create_strict_mappings(fpga->irqdomain, base_irq, 0,
+						 CPLDS_NB_IRQ);
+		if (ret) {
+			dev_err(&pdev->dev, "couldn't create the irq mapping %d..%d\n",
+				base_irq, base_irq + CPLDS_NB_IRQ);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int cplds_remove(struct platform_device *pdev)
+{
+	struct cplds *fpga = platform_get_drvdata(pdev);
+
+	irq_set_chip_and_handler(fpga->irq, NULL, NULL);
+
+	return 0;
+}
+
+static const struct of_device_id cplds_id_table[] = {
+	{ .compatible = "intel,lubbock-cplds-irqs", },
+	{ .compatible = "intel,mainstone-cplds-irqs", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, cplds_id_table);
+
+static struct platform_driver cplds_driver = {
+	.driver		= {
+		.name	= "pxa_cplds_irqs",
+		.of_match_table = of_match_ptr(cplds_id_table),
+	},
+	.probe		= cplds_probe,
+	.remove		= cplds_remove,
+	.resume		= cplds_resume,
+};
+
+module_platform_driver(cplds_driver);
+
+MODULE_DESCRIPTION("PXA Cplds interrupts driver");
+MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>");
+MODULE_LICENSE("GPL");

arch/arm/mach-rockchip/pm.c

@@ -83,6 +83,13 @@ static void rk3288_slp_mode_set(int level)
 		     SGRF_PCLK_WDT_GATE | SGRF_FAST_BOOT_EN
 		     | SGRF_PCLK_WDT_GATE_WRITE | SGRF_FAST_BOOT_EN_WRITE);
 
+	/*
+	 * The dapswjdp can not auto reset before resume, that cause it may
+	 * access some illegal address during resume. Let's disable it before
+	 * suspend, and the MASKROM will enable it back.
+	 */
+	regmap_write(sgrf_regmap, RK3288_SGRF_CPU_CON0, SGRF_DAPDEVICEEN_WRITE);
+
 	/* booting address of resuming system is from this register value */
 	regmap_write(sgrf_regmap, RK3288_SGRF_FAST_BOOT_ADDR,
 		     rk3288_bootram_phy);

arch/arm/mach-rockchip/pm.h

@@ -55,6 +55,10 @@ static inline void rockchip_suspend_init(void)
 #define SGRF_FAST_BOOT_EN		BIT(8)
 #define SGRF_FAST_BOOT_EN_WRITE		BIT(24)
 
+#define RK3288_SGRF_CPU_CON0		(0x40)
+#define SGRF_DAPDEVICEEN		BIT(0)
+#define SGRF_DAPDEVICEEN_WRITE		BIT(16)
+
 #define RK3288_CRU_MODE_CON		0x50
 #define RK3288_CRU_SEL0_CON		0x60
 #define RK3288_CRU_SEL1_CON		0x64

arch/arm/mach-rockchip/rockchip.c

@@ -30,11 +30,30 @@
 #include "pm.h"
 
 #define RK3288_GRF_SOC_CON0 0x244
+#define RK3288_TIMER6_7_PHYS 0xff810000
 
 static void __init rockchip_timer_init(void)
 {
 	if (of_machine_is_compatible("rockchip,rk3288")) {
 		struct regmap *grf;
+		void __iomem *reg_base;
+
+		/*
+		 * Most/all uboot versions for rk3288 don't enable timer7
+		 * which is needed for the architected timer to work.
+		 * So make sure it is running during early boot.
+		 */
+		reg_base = ioremap(RK3288_TIMER6_7_PHYS, SZ_16K);
+		if (reg_base) {
+			writel(0, reg_base + 0x30);
+			writel(0xffffffff, reg_base + 0x20);
+			writel(0xffffffff, reg_base + 0x24);
+			writel(1, reg_base + 0x30);
+			dsb();
+			iounmap(reg_base);
+		} else {
+			pr_err("rockchip: could not map timer7 registers\n");
+		}
 
 		/*
 		 * Disable auto jtag/sdmmc switching that causes issues

arch/arm/mm/dma-mapping.c

@@ -1878,7 +1878,7 @@ struct dma_map_ops iommu_coherent_ops = {
  * arm_iommu_attach_device function.
  */
 struct dma_iommu_mapping *
-arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size)
+arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, u64 size)
 {
 	unsigned int bits = size >> PAGE_SHIFT;
 	unsigned int bitmap_size = BITS_TO_LONGS(bits) * sizeof(long);
@@ -1886,6 +1886,10 @@ arm_iommu_create_mapping(struct bus_type *bus, dma_addr_t base, size_t size)
 	int extensions = 1;
 	int err = -ENOMEM;
 
+	/* currently only 32-bit DMA address space is supported */
+	if (size > DMA_BIT_MASK(32) + 1)
+		return ERR_PTR(-ERANGE);
+
 	if (!bitmap_size)
 		return ERR_PTR(-EINVAL);
 
@@ -2057,13 +2061,6 @@ static bool arm_setup_iommu_dma_ops(struct device *dev, u64 dma_base, u64 size,
 	if (!iommu)
 		return false;
 
-	/*
-	 * currently arm_iommu_create_mapping() takes a max of size_t
-	 * for size param. So check this limit for now.
-	 */
-	if (size > SIZE_MAX)
-		return false;
-
 	mapping = arm_iommu_create_mapping(dev->bus, dma_base, size);
 	if (IS_ERR(mapping)) {
 		pr_warn("Failed to create %llu-byte IOMMU mapping for device %s\n",

arch/arm/mm/proc-arm1020.S

@@ -22,8 +22,6 @@
  *
  * These are the low level assembler for performing cache and TLB
  * functions on the arm1020.
- *
- *  CONFIG_CPU_ARM1020_CPU_IDLE -> nohlt
  */
 #include <linux/linkage.h>
 #include <linux/init.h>

arch/arm/mm/proc-arm1020e.S

@@ -22,8 +22,6 @@
  *
  * These are the low level assembler for performing cache and TLB
  * functions on the arm1020e.
- *
- *  CONFIG_CPU_ARM1020_CPU_IDLE -> nohlt
  */
 #include <linux/linkage.h>
 #include <linux/init.h>

arch/arm/mm/proc-arm925.S

@@ -441,9 +441,6 @@ ENTRY(cpu_arm925_set_pte_ext)
 	.type	__arm925_setup, #function
 __arm925_setup:
 	mov	r0, #0
-#if defined(CONFIG_CPU_ICACHE_STREAMING_DISABLE)
-        orr     r0,r0,#1 << 7
-#endif
 
 	/* Transparent on, D-cache clean & flush mode. See  NOTE2 above */
         orr     r0,r0,#1 << 1			@ transparent mode on

arch/arm/mm/proc-feroceon.S

@@ -602,7 +602,6 @@ __\name\()_proc_info:
 		PMD_SECT_AP_WRITE | \
 		PMD_SECT_AP_READ
 	initfn	__feroceon_setup, __\name\()_proc_info
-	.long __feroceon_setup
 	.long	cpu_arch_name
 	.long	cpu_elf_name
 	.long	HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP

arch/arm/net/bpf_jit_32.c

@@ -54,6 +54,7 @@
 #define SEEN_DATA		(1 << (BPF_MEMWORDS + 3))
 
 #define FLAG_NEED_X_RESET	(1 << 0)
+#define FLAG_IMM_OVERFLOW	(1 << 1)
 
 struct jit_ctx {
 	const struct bpf_prog *skf;
@@ -293,6 +294,15 @@ static u16 imm_offset(u32 k, struct jit_ctx *ctx)
 	/* PC in ARM mode == address of the instruction + 8 */
 	imm = offset - (8 + ctx->idx * 4);
 
+	if (imm & ~0xfff) {
+		/*
+		 * literal pool is too far, signal it into flags. we
+		 * can only detect it on the second pass unfortunately.
+		 */
+		ctx->flags |= FLAG_IMM_OVERFLOW;
+		return 0;
+	}
+
 	return imm;
 }
 
@@ -449,10 +459,21 @@ static inline void emit_udiv(u8 rd, u8 rm, u8 rn, struct jit_ctx *ctx)
 		return;
 	}
 #endif
-	if (rm != ARM_R0)
-		emit(ARM_MOV_R(ARM_R0, rm), ctx);
+
+	/*
+	 * For BPF_ALU | BPF_DIV | BPF_K instructions, rm is ARM_R4
+	 * (r_A) and rn is ARM_R0 (r_scratch) so load rn first into
+	 * ARM_R1 to avoid accidentally overwriting ARM_R0 with rm
+	 * before using it as a source for ARM_R1.
+	 *
+	 * For BPF_ALU | BPF_DIV | BPF_X rm is ARM_R4 (r_A) and rn is
+	 * ARM_R5 (r_X) so there is no particular register overlap
+	 * issues.
+	 */
 	if (rn != ARM_R1)
 		emit(ARM_MOV_R(ARM_R1, rn), ctx);
+	if (rm != ARM_R0)
+		emit(ARM_MOV_R(ARM_R0, rm), ctx);
 
 	ctx->seen |= SEEN_CALL;
 	emit_mov_i(ARM_R3, (u32)jit_udiv, ctx);
@@ -855,6 +876,14 @@ static int build_body(struct jit_ctx *ctx)
 		default:
 			return -1;
 		}
+
+		if (ctx->flags & FLAG_IMM_OVERFLOW)
+			/*
+			 * this instruction generated an overflow when
+			 * trying to access the literal pool, so
+			 * delegate this filter to the kernel interpreter.
+			 */
+			return -1;
 	}
 
 	/* compute offsets only during the first pass */
@@ -917,7 +946,14 @@ void bpf_jit_compile(struct bpf_prog *fp)
 	ctx.idx = 0;
 
 	build_prologue(&ctx);
-	build_body(&ctx);
+	if (build_body(&ctx) < 0) {
+#if __LINUX_ARM_ARCH__ < 7
+		if (ctx.imm_count)
+			kfree(ctx.imms);
+#endif
+		bpf_jit_binary_free(header);
+		goto out;
+	}
 	build_epilogue(&ctx);
 
 	flush_icache_range((u32)ctx.target, (u32)(ctx.target + ctx.idx));

arch/arm64/boot/dts/arm/juno-motherboard.dtsi

@@ -21,6 +21,20 @@
 			clock-output-names = "juno_mb:clk25mhz";
 		};
 
+		v2m_refclk1mhz: refclk1mhz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1000000>;
+			clock-output-names = "juno_mb:refclk1mhz";
+		};
+
+		v2m_refclk32khz: refclk32khz {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "juno_mb:refclk32khz";
+		};
+
 		motherboard {
 			compatible = "arm,vexpress,v2p-p1", "simple-bus";
 			#address-cells = <2>;  /* SMB chipselect number and offset */
@@ -66,6 +80,15 @@
 				#size-cells = <1>;
 				ranges = <0 3 0 0x200000>;
 
+				v2m_sysctl: sysctl@020000 {
+					compatible = "arm,sp810", "arm,primecell";
+					reg = <0x020000 0x1000>;
+					clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&mb_clk24mhz>;
+					clock-names = "refclk", "timclk", "apb_pclk";
+					#clock-cells = <1>;
+					clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
+				};
+
 				mmci@050000 {
 					compatible = "arm,pl180", "arm,primecell";
 					reg = <0x050000 0x1000>;
@@ -106,16 +129,16 @@
 					compatible = "arm,sp804", "arm,primecell";
 					reg = <0x110000 0x10000>;
 					interrupts = <9>;
-					clocks = <&mb_clk24mhz>, <&soc_smc50mhz>;
-					clock-names = "timclken1", "apb_pclk";
+					clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&mb_clk24mhz>;
+					clock-names = "timclken1", "timclken2", "apb_pclk";
 				};
 
 				v2m_timer23: timer@120000 {
 					compatible = "arm,sp804", "arm,primecell";
 					reg = <0x120000 0x10000>;
 					interrupts = <9>;
-					clocks = <&mb_clk24mhz>, <&soc_smc50mhz>;
-					clock-names = "timclken1", "apb_pclk";
+					clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&mb_clk24mhz>;
+					clock-names = "timclken1", "timclken2", "apb_pclk";
 				};
 
 				rtc@170000 {

arch/arm64/crypto/crc32-arm64.c

@@ -147,13 +147,21 @@ static int chksum_final(struct shash_desc *desc, u8 *out)
 {
 	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
 
+	put_unaligned_le32(ctx->crc, out);
+	return 0;
+}
+
+static int chksumc_final(struct shash_desc *desc, u8 *out)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
 	put_unaligned_le32(~ctx->crc, out);
 	return 0;
 }
 
 static int __chksum_finup(u32 crc, const u8 *data, unsigned int len, u8 *out)
 {
-	put_unaligned_le32(~crc32_arm64_le_hw(crc, data, len), out);
+	put_unaligned_le32(crc32_arm64_le_hw(crc, data, len), out);
 	return 0;
 }
 
@@ -199,6 +207,14 @@ static int crc32_cra_init(struct crypto_tfm *tfm)
 {
 	struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
 
+	mctx->key = 0;
+	return 0;
+}
+
+static int crc32c_cra_init(struct crypto_tfm *tfm)
+{
+	struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
+
 	mctx->key = ~0;
 	return 0;
 }
@@ -229,7 +245,7 @@ static struct shash_alg crc32c_alg = {
 	.setkey			=	chksum_setkey,
 	.init			=	chksum_init,
 	.update			=	chksumc_update,
-	.final			=	chksum_final,
+	.final			=	chksumc_final,
 	.finup			=	chksumc_finup,
 	.digest			=	chksumc_digest,
 	.descsize		=	sizeof(struct chksum_desc_ctx),
@@ -241,7 +257,7 @@ static struct shash_alg crc32c_alg = {
 		.cra_alignmask		=	0,
 		.cra_ctxsize		=	sizeof(struct chksum_ctx),
 		.cra_module		=	THIS_MODULE,
-		.cra_init		=	crc32_cra_init,
+		.cra_init		=	crc32c_cra_init,
 	}
 };
 

arch/arm64/crypto/sha1-ce-glue.c

@@ -74,6 +74,9 @@ static int sha1_ce_finup(struct shash_desc *desc, const u8 *data,
 
 static int sha1_ce_final(struct shash_desc *desc, u8 *out)
 {
+	struct sha1_ce_state *sctx = shash_desc_ctx(desc);
+
+	sctx->finalize = 0;
 	kernel_neon_begin_partial(16);
 	sha1_base_do_finalize(desc, (sha1_block_fn *)sha1_ce_transform);
 	kernel_neon_end();

arch/arm64/crypto/sha2-ce-glue.c

@@ -75,6 +75,9 @@ static int sha256_ce_finup(struct shash_desc *desc, const u8 *data,
 
 static int sha256_ce_final(struct shash_desc *desc, u8 *out)
 {
+	struct sha256_ce_state *sctx = shash_desc_ctx(desc);
+
+	sctx->finalize = 0;
 	kernel_neon_begin_partial(28);
 	sha256_base_do_finalize(desc, (sha256_block_fn *)sha2_ce_transform);
 	kernel_neon_end();

arch/arm64/kernel/alternative.c

@@ -24,7 +24,6 @@
 #include <asm/cacheflush.h>
 #include <asm/alternative.h>
 #include <asm/cpufeature.h>
-#include <asm/insn.h>
 #include <linux/stop_machine.h>
 
 extern struct alt_instr __alt_instructions[], __alt_instructions_end[];
@@ -34,48 +33,6 @@ struct alt_region {
 	struct alt_instr *end;
 };
 
-/*
- * Decode the imm field of a b/bl instruction, and return the byte
- * offset as a signed value (so it can be used when computing a new
- * branch target).
- */
-static s32 get_branch_offset(u32 insn)
-{
-	s32 imm = aarch64_insn_decode_immediate(AARCH64_INSN_IMM_26, insn);
-
-	/* sign-extend the immediate before turning it into a byte offset */
-	return (imm << 6) >> 4;
-}
-
-static u32 get_alt_insn(u8 *insnptr, u8 *altinsnptr)
-{
-	u32 insn;
-
-	aarch64_insn_read(altinsnptr, &insn);
-
-	/* Stop the world on instructions we don't support... */
-	BUG_ON(aarch64_insn_is_cbz(insn));
-	BUG_ON(aarch64_insn_is_cbnz(insn));
-	BUG_ON(aarch64_insn_is_bcond(insn));
-	/* ... and there is probably more. */
-
-	if (aarch64_insn_is_b(insn) || aarch64_insn_is_bl(insn)) {
-		enum aarch64_insn_branch_type type;
-		unsigned long target;
-
-		if (aarch64_insn_is_b(insn))
-			type = AARCH64_INSN_BRANCH_NOLINK;
-		else
-			type = AARCH64_INSN_BRANCH_LINK;
-
-		target = (unsigned long)altinsnptr + get_branch_offset(insn);
-		insn = aarch64_insn_gen_branch_imm((unsigned long)insnptr,
-						   target, type);
-	}
-
-	return insn;
-}
-
 static int __apply_alternatives(void *alt_region)
 {
 	struct alt_instr *alt;
@@ -83,9 +40,6 @@ static int __apply_alternatives(void *alt_region)
 	u8 *origptr, *replptr;
 
 	for (alt = region->begin; alt < region->end; alt++) {
-		u32 insn;
-		int i;
-
 		if (!cpus_have_cap(alt->cpufeature))
 			continue;
 
@@ -95,12 +49,7 @@ static int __apply_alternatives(void *alt_region)
 
 		origptr = (u8 *)&alt->orig_offset + alt->orig_offset;
 		replptr = (u8 *)&alt->alt_offset + alt->alt_offset;
-
-		for (i = 0; i < alt->alt_len; i += sizeof(insn)) {
-			insn = get_alt_insn(origptr + i, replptr + i);
-			aarch64_insn_write(origptr + i, insn);
-		}
-
+		memcpy(origptr, replptr, alt->alt_len);
 		flush_icache_range((uintptr_t)origptr,
 				   (uintptr_t)(origptr + alt->alt_len));
 	}

arch/arm64/kernel/perf_event.c

@@ -1315,15 +1315,15 @@ static int armpmu_device_probe(struct platform_device *pdev)
 	if (!cpu_pmu)
 		return -ENODEV;
 
-	irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
-	if (!irqs)
-		return -ENOMEM;
-
 	/* Don't bother with PPIs; they're already affine */
 	irq = platform_get_irq(pdev, 0);
 	if (irq >= 0 && irq_is_percpu(irq))
 		return 0;
 
+	irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
+	if (!irqs)
+		return -ENOMEM;
+
 	for (i = 0; i < pdev->num_resources; ++i) {
 		struct device_node *dn;
 		int cpu;

arch/arm64/mm/dump.c

@@ -328,10 +328,12 @@ static int ptdump_init(void)
 			for (j = 0; j < pg_level[i].num; j++)
 				pg_level[i].mask |= pg_level[i].bits[j].mask;
 
+#ifdef CONFIG_SPARSEMEM_VMEMMAP
 	address_markers[VMEMMAP_START_NR].start_address =
 				(unsigned long)virt_to_page(PAGE_OFFSET);
 	address_markers[VMEMMAP_END_NR].start_address =
 				(unsigned long)virt_to_page(high_memory);
+#endif
 
 	pe = debugfs_create_file("kernel_page_tables", 0400, NULL, NULL,
 				 &ptdump_fops);

arch/arm64/net/bpf_jit_comp.c

@@ -487,7 +487,7 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx)
 			return -EINVAL;
 		}
 
-		imm64 = (u64)insn1.imm << 32 | imm;
+		imm64 = (u64)insn1.imm << 32 | (u32)imm;
 		emit_a64_mov_i64(dst, imm64, ctx);
 
 		return 1;

arch/m32r/kernel/smp.c

@@ -45,7 +45,7 @@ static volatile unsigned long flushcache_cpumask = 0;
 /*
  * For flush_tlb_others()
  */
-static volatile cpumask_t flush_cpumask;
+static cpumask_t flush_cpumask;
 static struct mm_struct *flush_mm;
 static struct vm_area_struct *flush_vma;
 static volatile unsigned long flush_va;
@@ -415,7 +415,7 @@ static void flush_tlb_others(cpumask_t cpumask, struct mm_struct *mm,
 	 */
 	send_IPI_mask(&cpumask, INVALIDATE_TLB_IPI, 0);
 
-	while (!cpumask_empty((cpumask_t*)&flush_cpumask)) {
+	while (!cpumask_empty(&flush_cpumask)) {
 		/* nothing. lockup detection does not belong here */
 		mb();
 	}
@@ -468,7 +468,7 @@ void smp_invalidate_interrupt(void)
 			__flush_tlb_page(va);
 		}
 	}
-	cpumask_clear_cpu(cpu_id, (cpumask_t*)&flush_cpumask);
+	cpumask_clear_cpu(cpu_id, &flush_cpumask);
 }
 
 /*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*/

arch/mips/Makefile

@@ -277,7 +277,7 @@ LDFLAGS			+= -m $(ld-emul)
 ifdef CONFIG_MIPS
 CHECKFLAGS += $(shell $(CC) $(KBUILD_CFLAGS) -dM -E -x c /dev/null | \
 	egrep -vw '__GNUC_(|MINOR_|PATCHLEVEL_)_' | \
-	sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/")
+	sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/" -e 's/\$$/&&/g')
 ifdef CONFIG_64BIT
 CHECKFLAGS		+= -m64
 endif

arch/mips/include/asm/elf.h

@@ -304,7 +304,7 @@ do {									\
 									\
 	current->thread.abi = &mips_abi;				\
 									\
-	current->thread.fpu.fcr31 = current_cpu_data.fpu_csr31;		\
+	current->thread.fpu.fcr31 = boot_cpu_data.fpu_csr31;		\
 } while (0)
 
 #endif /* CONFIG_32BIT */
@@ -366,7 +366,7 @@ do {									\
 	else								\
 		current->thread.abi = &mips_abi;			\
 									\
-	current->thread.fpu.fcr31 = current_cpu_data.fpu_csr31;		\
+	current->thread.fpu.fcr31 = boot_cpu_data.fpu_csr31;		\
 									\
 	p = personality(current->personality);				\
 	if (p != PER_LINUX32 && p != PER_LINUX)				\

arch/mips/include/asm/smp.h

@@ -45,7 +45,7 @@ extern int __cpu_logical_map[NR_CPUS];
 #define SMP_DUMP		0x8
 #define SMP_ASK_C0COUNT		0x10
 
-extern volatile cpumask_t cpu_callin_map;
+extern cpumask_t cpu_callin_map;
 
 /* Mask of CPUs which are currently definitely operating coherently */
 extern cpumask_t cpu_coherent_mask;

arch/mips/kernel/elf.c

@@ -76,14 +76,6 @@ int arch_elf_pt_proc(void *_ehdr, void *_phdr, struct file *elf,
 
 	/* Lets see if this is an O32 ELF */
 	if (ehdr32->e_ident[EI_CLASS] == ELFCLASS32) {
-		/* FR = 1 for N32 */
-		if (ehdr32->e_flags & EF_MIPS_ABI2)
-			state->overall_fp_mode = FP_FR1;
-		else
-			/* Set a good default FPU mode for O32 */
-			state->overall_fp_mode = cpu_has_mips_r6 ?
-				FP_FRE : FP_FR0;
-
 		if (ehdr32->e_flags & EF_MIPS_FP64) {
 			/*
 			 * Set MIPS_ABI_FP_OLD_64 for EF_MIPS_FP64. We will override it
@@ -104,9 +96,6 @@ int arch_elf_pt_proc(void *_ehdr, void *_phdr, struct file *elf,
 				  (char *)&abiflags,
 				  sizeof(abiflags));
 	} else {
-		/* FR=1 is really the only option for 64-bit */
-		state->overall_fp_mode = FP_FR1;
-
 		if (phdr64->p_type != PT_MIPS_ABIFLAGS)
 			return 0;
 		if (phdr64->p_filesz < sizeof(abiflags))
@@ -137,6 +126,7 @@ int arch_check_elf(void *_ehdr, bool has_interpreter,
 	struct elf32_hdr *ehdr = _ehdr;
 	struct mode_req prog_req, interp_req;
 	int fp_abi, interp_fp_abi, abi0, abi1, max_abi;
+	bool is_mips64;
 
 	if (!config_enabled(CONFIG_MIPS_O32_FP64_SUPPORT))
 		return 0;
@@ -152,10 +142,22 @@ int arch_check_elf(void *_ehdr, bool has_interpreter,
 		abi0 = abi1 = fp_abi;
 	}
 
-	/* ABI limits. O32 = FP_64A, N32/N64 = FP_SOFT */
-	max_abi = ((ehdr->e_ident[EI_CLASS] == ELFCLASS32) &&
-		   (!(ehdr->e_flags & EF_MIPS_ABI2))) ?
-		MIPS_ABI_FP_64A : MIPS_ABI_FP_SOFT;
+	is_mips64 = (ehdr->e_ident[EI_CLASS] == ELFCLASS64) ||
+		    (ehdr->e_flags & EF_MIPS_ABI2);
+
+	if (is_mips64) {
+		/* MIPS64 code always uses FR=1, thus the default is easy */
+		state->overall_fp_mode = FP_FR1;
+
+		/* Disallow access to the various FPXX & FP64 ABIs */
+		max_abi = MIPS_ABI_FP_SOFT;
+	} else {
+		/* Default to a mode capable of running code expecting FR=0 */
+		state->overall_fp_mode = cpu_has_mips_r6 ? FP_FRE : FP_FR0;
+
+		/* Allow all ABIs we know about */
+		max_abi = MIPS_ABI_FP_64A;
+	}
 
 	if ((abi0 > max_abi && abi0 != MIPS_ABI_FP_UNKNOWN) ||
 	    (abi1 > max_abi && abi1 != MIPS_ABI_FP_UNKNOWN))

arch/mips/kernel/ptrace.c

@@ -176,7 +176,7 @@ int ptrace_setfpregs(struct task_struct *child, __u32 __user *data)
 
 	__get_user(value, data + 64);
 	fcr31 = child->thread.fpu.fcr31;
-	mask = current_cpu_data.fpu_msk31;
+	mask = boot_cpu_data.fpu_msk31;
 	child->thread.fpu.fcr31 = (value & ~mask) | (fcr31 & mask);
 
 	/* FIR may not be written.  */

arch/mips/kernel/smp-cps.c

@@ -92,7 +92,7 @@ static void __init cps_smp_setup(void)
 #ifdef CONFIG_MIPS_MT_FPAFF
 	/* If we have an FPU, enroll ourselves in the FPU-full mask */
 	if (cpu_has_fpu)
-		cpu_set(0, mt_fpu_cpumask);
+		cpumask_set_cpu(0, &mt_fpu_cpumask);
 #endif /* CONFIG_MIPS_MT_FPAFF */
 }
 

arch/mips/kernel/smp.c

@@ -43,7 +43,7 @@
 #include <asm/time.h>
 #include <asm/setup.h>
 
-volatile cpumask_t cpu_callin_map;	/* Bitmask of started secondaries */
+cpumask_t cpu_callin_map;		/* Bitmask of started secondaries */
 
 int __cpu_number_map[NR_CPUS];		/* Map physical to logical */
 EXPORT_SYMBOL(__cpu_number_map);
@@ -218,8 +218,10 @@ int __cpu_up(unsigned int cpu, struct task_struct *tidle)
 	/*
 	 * Trust is futile.  We should really have timeouts ...
 	 */
-	while (!cpumask_test_cpu(cpu, &cpu_callin_map))
+	while (!cpumask_test_cpu(cpu, &cpu_callin_map)) {
 		udelay(100);
+		schedule();
+	}
 
 	synchronise_count_master(cpu);
 	return 0;

arch/mips/kernel/traps.c

@@ -269,7 +269,6 @@ static void __show_regs(const struct pt_regs *regs)
 	 */
 	printk("epc   : %0*lx %pS\n", field, regs->cp0_epc,
 	       (void *) regs->cp0_epc);
-	printk("    %s\n", print_tainted());
 	printk("ra    : %0*lx %pS\n", field, regs->regs[31],
 	       (void *) regs->regs[31]);
 

arch/mips/kvm/emulate.c

@@ -2389,7 +2389,6 @@ enum emulation_result kvm_mips_complete_mmio_load(struct kvm_vcpu *vcpu,
 {
 	unsigned long *gpr = &vcpu->arch.gprs[vcpu->arch.io_gpr];
 	enum emulation_result er = EMULATE_DONE;
-	unsigned long curr_pc;
 
 	if (run->mmio.len > sizeof(*gpr)) {
 		kvm_err("Bad MMIO length: %d", run->mmio.len);
@@ -2397,11 +2396,6 @@ enum emulation_result kvm_mips_complete_mmio_load(struct kvm_vcpu *vcpu,
 		goto done;
 	}
 
-	/*
-	 * Update PC and hold onto current PC in case there is
-	 * an error and we want to rollback the PC
-	 */
-	curr_pc = vcpu->arch.pc;
 	er = update_pc(vcpu, vcpu->arch.pending_load_cause);
 	if (er == EMULATE_FAIL)
 		return er;

arch/mips/math-emu/cp1emu.c

@@ -889,7 +889,7 @@ static inline void cop1_cfc(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
 		break;
 
 	case FPCREG_RID:
-		value = current_cpu_data.fpu_id;
+		value = boot_cpu_data.fpu_id;
 		break;
 
 	default:
@@ -921,7 +921,7 @@ static inline void cop1_ctc(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
 			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
 
 		/* Preserve read-only bits.  */
-		mask = current_cpu_data.fpu_msk31;
+		mask = boot_cpu_data.fpu_msk31;
 		fcr31 = (value & ~mask) | (fcr31 & mask);
 		break;
 

arch/mips/mm/tlb-r4k.c

@@ -495,7 +495,7 @@ static void r4k_tlb_configure(void)
 
 	if (cpu_has_rixi) {
 		/*
-		 * Enable the no read, no exec bits, and enable large virtual
+		 * Enable the no read, no exec bits, and enable large physical
 		 * address.
 		 */
 #ifdef CONFIG_64BIT

arch/mips/sgi-ip32/ip32-platform.c

@@ -130,9 +130,9 @@ struct platform_device ip32_rtc_device = {
 	.resource		= ip32_rtc_resources,
 };
 
-+static int __init sgio2_rtc_devinit(void)
+static __init int sgio2_rtc_devinit(void)
 {
 	return platform_device_register(&ip32_rtc_device);
 }
 
-device_initcall(sgio2_cmos_devinit);
+device_initcall(sgio2_rtc_devinit);

arch/parisc/include/asm/elf.h

@@ -348,6 +348,10 @@ struct pt_regs;	/* forward declaration... */
 
 #define ELF_HWCAP	0
 
+#define STACK_RND_MASK	(is_32bit_task() ? \
+				0x7ff >> (PAGE_SHIFT - 12) : \
+				0x3ffff >> (PAGE_SHIFT - 12))
+
 struct mm_struct;
 extern unsigned long arch_randomize_brk(struct mm_struct *);
 #define arch_randomize_brk arch_randomize_brk