omap3evm: add support for the WL12xx WLAN module to the AM/DM3xx Evaluation Module

Adds platform initialization for working with the WLAN module attached to the evaluation module.
The patch includes MMC2 initialization, SDIO and control pins muxing and platform device registration
Signed-off-by: NEyal Reizer <eyalr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/mach-omap2/board-omap3evm.c

@@ -30,6 +30,8 @@
 #include <linux/usb/otg.h>
 #include <linux/smsc911x.h>
 
+#include <linux/wl12xx.h>
+#include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/mmc/host.h>
 
@@ -381,6 +383,16 @@ static struct omap2_hsmmc_info mmc[] = {
 		.gpio_cd	= -EINVAL,
 		.gpio_wp	= 63,
 	},
+#ifdef CONFIG_WL12XX_PLATFORM_DATA
+	{
+		.name		= "wl1271",
+		.mmc            = 2,
+		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
+		.gpio_wp	= -EINVAL,
+		.gpio_cd	= -EINVAL,
+		.nonremovable	= true,
+	},
+#endif
 	{}	/* Terminator */
 };
 
@@ -538,6 +550,50 @@ static struct regulator_init_data omap3_evm_vpll2 = {
 	.consumer_supplies	= &omap3_evm_vpll2_supply,
 };
 
+#ifdef CONFIG_WL12XX_PLATFORM_DATA
+
+#define OMAP3EVM_WLAN_PMENA_GPIO	(150)
+#define OMAP3EVM_WLAN_IRQ_GPIO		(149)
+
+static struct regulator_consumer_supply omap3evm_vmmc2_supply = {
+	.supply			= "vmmc",
+	.dev_name		= "mmci-omap-hs.1",
+};
+
+/* VMMC2 for driving the WL12xx module */
+static struct regulator_init_data omap3evm_vmmc2 = {
+	.constraints = {
+		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies	= 1,
+	.consumer_supplies = &omap3evm_vmmc2_supply,
+};
+
+static struct fixed_voltage_config omap3evm_vwlan = {
+	.supply_name		= "vwl1271",
+	.microvolts		= 1800000, /* 1.80V */
+	.gpio			= OMAP3EVM_WLAN_PMENA_GPIO,
+	.startup_delay		= 70000, /* 70ms */
+	.enable_high		= 1,
+	.enabled_at_boot	= 0,
+	.init_data		= &omap3evm_vmmc2,
+};
+
+static struct platform_device omap3evm_vwlan_device = {
+	.name		= "reg-fixed-voltage",
+	.id		= 1,
+	.dev = {
+		.platform_data	= &omap3evm_vwlan,
+	},
+};
+
+struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
+	.irq = OMAP_GPIO_IRQ(OMAP3EVM_WLAN_IRQ_GPIO),
+	/* ref clock is 38.4 MHz */
+	.board_ref_clock = 2,
+};
+#endif
+
 static struct twl4030_platform_data omap3evm_twldata = {
 	.irq_base	= TWL4030_IRQ_BASE,
 	.irq_end	= TWL4030_IRQ_END,
@@ -657,6 +713,21 @@ static struct omap_board_mux board_mux[] __initdata = {
 				OMAP_PIN_OFF_WAKEUPENABLE),
 	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
 				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW),
+#ifdef CONFIG_WL12XX_PLATFORM_DATA
+	/* WLAN IRQ - GPIO 149 */
+	OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
+
+	/* WLAN POWER ENABLE - GPIO 150 */
+	OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+
+	/* MMC2 SDIO pin muxes for WL12xx */
+	OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+	OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
+#endif
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #endif
@@ -714,6 +785,13 @@ static void __init omap3_evm_init(void)
 	ads7846_dev_init();
 	omap3evm_init_smsc911x();
 	omap3_evm_display_init();
+
+#ifdef CONFIG_WL12XX_PLATFORM_DATA
+	/* WL12xx WLAN Init */
+	if (wl12xx_set_platform_data(&omap3evm_wlan_data))
+		pr_err("error setting wl12xx data\n");
+	platform_device_register(&omap3evm_vwlan_device);
+#endif
 }
 
 MACHINE_START(OMAP3EVM, "OMAP3 EVM")