ACPI: fix two IRQ8 issues in IOAPIC mode

Use mp_irqs[] to get PNP device's interrupt polarity and trigger.
There are two reasons to do this:
1. BIOS bug for PNP interrupt
2. BIOS explictly does override
mp_irqs[] should cover all the cases.

http://bugzilla.kernel.org/show_bug.cgi?id=5243
http://bugzilla.kernel.org/show_bug.cgi?id=7679
http://bugzilla.kernel.org/show_bug.cgi?id=9153

[lenb: fixed !IOAPIC and 64-bit !SMP builds]
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

arch/x86/kernel/io_apic_32.c

@@ -962,7 +962,7 @@ static int EISA_ELCR(unsigned int irq)
 #define default_MCA_trigger(idx)	(1)
 #define default_MCA_polarity(idx)	(0)
 
-static int __init MPBIOS_polarity(int idx)
+static int MPBIOS_polarity(int idx)
 {
 	int bus = mp_irqs[idx].mpc_srcbus;
 	int polarity;
@@ -2830,6 +2830,25 @@ int io_apic_set_pci_routing (int ioapic, int pin, int irq, int edge_level, int a
 	return 0;
 }
 
+int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
+{
+	int i;
+
+	if (skip_ioapic_setup)
+		return -1;
+
+	for (i = 0; i < mp_irq_entries; i++)
+		if (mp_irqs[i].mpc_irqtype == mp_INT &&
+		    mp_irqs[i].mpc_srcbusirq == bus_irq)
+			break;
+	if (i >= mp_irq_entries)
+		return -1;
+
+	*trigger = irq_trigger(i);
+	*polarity = irq_polarity(i);
+	return 0;
+}
+
 #endif /* CONFIG_ACPI */
 
 static int __init parse_disable_timer_pin_1(char *arg)

arch/x86/kernel/io_apic_64.c

@@ -546,7 +546,7 @@ int IO_APIC_get_PCI_irq_vector(int bus, int slot, int pin)
 #define default_PCI_trigger(idx)	(1)
 #define default_PCI_polarity(idx)	(1)
 
-static int __init MPBIOS_polarity(int idx)
+static int MPBIOS_polarity(int idx)
 {
 	int bus = mp_irqs[idx].mpc_srcbus;
 	int polarity;
@@ -2222,8 +2222,27 @@ int io_apic_set_pci_routing (int ioapic, int pin, int irq, int triggering, int p
 	return 0;
 }
 
-#endif /* CONFIG_ACPI */
 
+int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
+{
+	int i;
+
+	if (skip_ioapic_setup)
+		return -1;
+
+	for (i = 0; i < mp_irq_entries; i++)
+		if (mp_irqs[i].mpc_irqtype == mp_INT &&
+		    mp_irqs[i].mpc_srcbusirq == bus_irq)
+			break;
+	if (i >= mp_irq_entries)
+		return -1;
+
+	*trigger = irq_trigger(i);
+	*polarity = irq_polarity(i);
+	return 0;
+}
+
+#endif /* CONFIG_ACPI */
 
 /*
  * This function currently is only a helper for the i386 smp boot process where
@@ -2260,3 +2279,4 @@ void __init setup_ioapic_dest(void)
 	}
 }
 #endif
+

drivers/pnp/pnpacpi/rsparser.c

@@ -75,6 +75,7 @@ static void pnpacpi_parse_allocated_irqresource(struct pnp_resource_table *res,
 {
 	int i = 0;
 	int irq;
+	int p, t;
 
 	if (!valid_IRQ(gsi))
 		return;
@@ -85,6 +86,23 @@ static void pnpacpi_parse_allocated_irqresource(struct pnp_resource_table *res,
 	if (i >= PNP_MAX_IRQ)
 		return;
 
+	/*
+	 * in IO-APIC mode, use overrided attribute. Two reasons:
+	 * 1. BIOS bug in DSDT
+	 * 2. BIOS uses IO-APIC mode Interrupt Source Override
+	 */
+	if (!acpi_get_override_irq(gsi, &t, &p)) {
+		t = t ? ACPI_LEVEL_SENSITIVE : ACPI_EDGE_SENSITIVE;
+		p = p ? ACPI_ACTIVE_LOW : ACPI_ACTIVE_HIGH;
+
+		if (triggering != t || polarity != p) {
+			pnp_warn("IRQ %d override to %s, %s",
+				gsi, t ? "edge":"level", p ? "low":"high");
+			triggering = t;
+			polarity = p;
+		}
+	}
+
 	res->irq_resource[i].flags = IORESOURCE_IRQ;	// Also clears _UNSET flag
 	res->irq_resource[i].flags |= irq_flags(triggering, polarity);
 	irq = acpi_register_gsi(gsi, triggering, polarity);

include/linux/acpi.h

@@ -132,6 +132,11 @@ extern unsigned long acpi_realmode_flags;
 int acpi_register_gsi (u32 gsi, int triggering, int polarity);
 int acpi_gsi_to_irq (u32 gsi, unsigned int *irq);
 
+#ifdef CONFIG_X86_IO_APIC
+extern int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity);
+#else
+#define acpi_get_override_irq(bus, trigger, polarity) (-1)
+#endif
 /*
  * This function undoes the effect of one call to acpi_register_gsi().
  * If this matches the last registration, any IRQ resources for gsi