Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt

Merge "First batch of AT91 DT material for 3.15" from Nicolas Ferre:

- activate DMA for NAND flash controller
- some binding documentation update for usba and ADC (iio) drivers
- removal of some deprecated ADC (iio) properties

* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: at91-cosino: remove useless adc properties
  ARM: at91/dt: sama5d3: remove useless adc properties
  ARM: at91/dt: at91sam9x5: remove useless adc properties
  ARM: at91/dt: at91sam9g45: remove useless adc properties
  ARM: at91/dt: at91sam9260: remove useless adc properties
  ARM: at91/dt: at91-ariag25: remove useless adc properties
  Documentation: dt: iio: move arm/atmel-adc.txt to iio/adc/at91_adc.txt
  Documentation: dt: iio: improve atmel-adc documentation
  ARM: at91: sama5d3: get rid of atmel_tsadcc driver
  ARM: at91/DT: atmel_usba correct atmel,vbus-gpio meaning
  ARM: at91/DT: add NAND + DMA property
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/arm/atmel-adc.txt → Documentation/devicetree/bindings/iio/adc/at91_adc.txt

@@ -5,32 +5,32 @@ Required properties:
     <chip> can be "at91sam9260", "at91sam9g45" or "at91sam9x5"
   - reg: Should contain ADC registers location and length
   - interrupts: Should contain the IRQ line for the ADC
-  - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
+  - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
     device
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
     defined in the datasheet
   - atmel,adc-vref: Reference voltage in millivolts for the conversions
-  - atmel,adc-res: List of resolution in bits supported by the ADC. List size
+  - atmel,adc-res: List of resolutions in bits supported by the ADC. List size
 		   must be two at least.
   - atmel,adc-res-names: Contains one identifier string for each resolution
 			 in atmel,adc-res property. "lowres" and "highres"
 			 identifiers are required.
 
 Optional properties:
-  - atmel,adc-use-external: Boolean to enable of external triggers
+  - atmel,adc-use-external-triggers: Boolean to enable the external triggers
   - atmel,adc-use-res: String corresponding to an identifier from
 		       atmel,adc-res-names property. If not specified, the highest
 		       resolution will be used.
   - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
   - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
-  - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
-                        value is set, then adc driver will enable touch screen
+  - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
+                        value is set, then the adc driver will enable touchscreen
                         support.
-    NOTE: when adc touch screen enabled, the adc hardware trigger will be
-          disabled. Since touch screen will occupied the trigger register.
+    NOTE: when adc touchscreen is enabled, the adc hardware trigger will be
+          disabled. Since touchscreen will occupy the trigger register.
   - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
-                                     make touch detect more precision.
- 
+                                     makes touch detection more precise.
+
 Optional trigger Nodes:
   - Required properties:
     * trigger-name: Name of the trigger exposed to the user
@@ -41,40 +41,41 @@ Optional trigger Nodes:
 
 Examples:
 adc0: adc@fffb0000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	compatible = "atmel,at91sam9260-adc";
 	reg = <0xfffb0000 0x100>;
-	interrupts = <20 4>;
-	atmel,adc-channel-base = <0x30>;
+	interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 	atmel,adc-channels-used = <0xff>;
-	atmel,adc-drdy-mask = <0x10000>;
-	atmel,adc-num-channels = <8>;
 	atmel,adc-startup-time = <40>;
-	atmel,adc-status-register = <0x1c>;
-	atmel,adc-trigger-register = <0x08>;
-	atmel,adc-use-external;
+	atmel,adc-use-external-triggers;
 	atmel,adc-vref = <3300>;
 	atmel,adc-res = <8 10>;
 	atmel,adc-res-names = "lowres", "highres";
 	atmel,adc-use-res = "lowres";
 
 	trigger@0 {
+		reg = <0>;
 		trigger-name = "external-rising";
 		trigger-value = <0x1>;
 		trigger-external;
 	};
 	trigger@1 {
+		reg = <1>;
 		trigger-name = "external-falling";
 		trigger-value = <0x2>;
 		trigger-external;
 	};
 
 	trigger@2 {
+		reg = <2>;
 		trigger-name = "external-any";
 		trigger-value = <0x3>;
 		trigger-external;
 	};
 
 	trigger@3 {
+		reg = <3>;
 		trigger-name = "continuous";
 		trigger-value = <0x6>;
 	};

Documentation/devicetree/bindings/usb/atmel-usb.txt

@@ -57,8 +57,8 @@ Required properties:
  - ep childnode: To specify the number of endpoints and their properties.
 
 Optional properties:
- - atmel,vbus-gpio: If present, specifies a gpio that needs to be
-   activated for the bus to be powered.
+ - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether
+   vbus is present (USB is connected).
 
 Required child node properties:
  - name: Name of the endpoint.

arch/arm/boot/dts/at91-ariag25.dts

@@ -129,7 +129,6 @@
 			adc0: adc@f804c000 {
 				status = "okay";
 				atmel,adc-channels-used = <0xf>;
-				atmel,adc-num-channels = <4>;
 			};
 
 			dbgu: serial@fffff200 {

arch/arm/boot/dts/at91-cosino.dtsi

@@ -64,7 +64,6 @@
 			};
 
 			adc0: adc@f804c000 {
-				atmel,adc-clock-rate = <1000000>;
 				atmel,adc-ts-wires = <4>;
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";

arch/arm/boot/dts/at91-cosino_mega2560.dts

@@ -27,7 +27,6 @@
 			};
 
 			adc0: adc@f804c000 {
-				atmel,adc-clock-rate = <1000000>;
 				atmel,adc-ts-wires = <4>;
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";

arch/arm/boot/dts/at91sam9260.dtsi

@@ -608,37 +608,38 @@
 			};
 
 			adc0: adc@fffe0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffe0000 0x100>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xf>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <4>;
 				atmel,adc-startup-time = <15>;
-				atmel,adc-channel-base = <0x30>;
-				atmel,adc-drdy-mask = <0x10000>;
-				atmel,adc-status-register = <0x1c>;
-				atmel,adc-trigger-register = <0x04>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "timer-counter-0";
 					trigger-value = <0x1>;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "timer-counter-1";
 					trigger-value = <0x3>;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "timer-counter-2";
 					trigger-value = <0x5>;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "external";
 					trigger-value = <0x13>;
 					trigger-external;

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -632,40 +632,41 @@
 			};
 
 			adc0: adc@fffb0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffb0000 0x100>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xff>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <8>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-channel-base = <0x30>;
-				atmel,adc-drdy-mask = <0x10000>;
-				atmel,adc-status-register = <0x1c>;
-				atmel,adc-trigger-register = <0x08>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
@@ -817,6 +818,7 @@
 			      >;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioC 8 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -570,6 +570,7 @@
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioD 5 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -621,41 +621,42 @@
 			};
 
 			adc0: adc@f804c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xf804c000 0x100>;
 				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
-				atmel,adc-use-external;
+				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xffff>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <12>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-channel-base = <0x50>;
-				atmel,adc-drdy-mask = <0x1000000>;
-				atmel,adc-status-register = <0x30>;
-				atmel,adc-trigger-register = <0xc0>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
@@ -790,6 +791,7 @@
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioD 5 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/sama5d3.dtsi

@@ -239,7 +239,9 @@
 			};
 
 			adc0: adc@f8018000 {
-				compatible = "atmel,at91sam9260-adc";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "atmel,at91sam9x5-adc";
 				reg = <0xf8018000 0x100>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
@@ -261,52 +263,39 @@
 				clocks = <&adc_clk>,
 					 <&adc_op_clk>;
 				clock-names = "adc_clk", "adc_op_clk";
-				atmel,adc-channel-base = <0x50>;
 				atmel,adc-channels-used = <0xfff>;
-				atmel,adc-drdy-mask = <0x1000000>;
-				atmel,adc-num-channels = <12>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-status-register = <0x30>;
-				atmel,adc-trigger-register = <0xc0>;
-				atmel,adc-use-external;
+				atmel,adc-use-external-triggers;
 				atmel,adc-vref = <3000>;
 				atmel,adc-res = <10 12>;
 				atmel,adc-res-names = "lowres", "highres";
 				status = "disabled";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
 			};
 
-			tsadcc: tsadcc@f8018000 {
-				compatible = "atmel,at91sam9x5-tsadcc";
-				reg = <0xf8018000 0x4000>;
-				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
-				atmel,tsadcc_clock = <300000>;
-				atmel,filtering_average = <0x03>;
-				atmel,pendet_debounce = <0x08>;
-				atmel,pendet_sensitivity = <0x02>;
-				atmel,ts_sample_hold_time = <0x0a>;
-				status = "disabled";
-			};
-
 			i2c2: i2c@f801c000 {
 				compatible = "atmel,at91sam9x5-i2c";
 				reg = <0xf801c000 0x4000>;
@@ -1256,6 +1245,7 @@
 			interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand0_ale_cle>;
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;

arch/arm/boot/dts/sama5d3xdm.dtsi

@@ -23,10 +23,8 @@
 			};
 
 			adc0: adc@f8018000 {
-				status = "disabled";
-			};
-
-			tsadcc: tsadcc@f8018000 {
+				atmel,adc-ts-wires = <4>;
+				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";
 			};