dsa: Move gpio reset into switch driver

Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.

There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/dsa/dsa.txt

@@ -31,8 +31,6 @@ A switch child node has the following optional property:
 			  switch. Must be set if the switch can not detect
 			  the presence and/or size of a connected EEPROM,
 			  otherwise optional.
-- reset-gpios		: phandle and specifier to a gpio line connected to
-			  reset pin of the switch chip.
 
 A switch may have multiple "port" children nodes
 

Documentation/devicetree/bindings/net/dsa/marvell.txt

@@ -10,10 +10,17 @@ If you need a stable binding, use the old dsa.txt binding.
 Marvell Switches are MDIO devices. The following properties should be
 placed as a child node of an mdio device.
 
+The properties described here are those specific to Marvell devices.
+Additional required and optional properties can be found in dsa.txt.
+
 Required properties:
 - compatible           : Should be one of "marvell,mv88e6085",
 - reg                  : Address on the MII bus for the switch.
 
+Optional properties:
+
+- reset-gpios		: Should be a gpio specifier for a reset line
+
 Example:
 
        mdio {
@@ -23,5 +30,6 @@ Example:
                switch0: switch@0 {
                        compatible = "marvell,mv88e6085";
                        reg = <0>;
+		       reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
                };
        };

drivers/net/dsa/mv88e6xxx.c

@@ -2582,7 +2582,7 @@ static int mv88e6xxx_switch_reset(struct mv88e6xxx_priv_state *ps)
 {
 	bool ppu_active = mv88e6xxx_has(ps, MV88E6XXX_FLAG_PPU_ACTIVE);
 	u16 is_reset = (ppu_active ? 0x8800 : 0xc800);
-	struct gpio_desc *gpiod = ps->ds->pd->reset;
+	struct gpio_desc *gpiod = ps->reset;
 	unsigned long timeout;
 	int ret;
 	int i;
@@ -3634,6 +3634,7 @@ int mv88e6xxx_probe(struct mdio_device *mdiodev)
 	struct mv88e6xxx_priv_state *ps;
 	int id, prod_num, rev;
 	struct dsa_switch *ds;
+	int err;
 
 	ds = devm_kzalloc(dev, sizeof(*ds) + sizeof(*ps), GFP_KERNEL);
 	if (!ds)
@@ -3663,6 +3664,17 @@ int mv88e6xxx_probe(struct mdio_device *mdiodev)
 	if (!ps->info)
 		return -ENODEV;
 
+	ps->reset = devm_gpiod_get(&mdiodev->dev, "reset", GPIOD_ASIS);
+	if (IS_ERR(ps->reset)) {
+		err = PTR_ERR(ps->reset);
+		if (err == -ENOENT) {
+			/* Optional, so not an error */
+			ps->reset = NULL;
+		} else {
+			return err;
+		}
+	}
+
 	dev_set_drvdata(dev, ds);
 
 	dev_info(dev, "switch 0x%x probed: %s, revision %u\n",

drivers/net/dsa/mv88e6xxx.h

@@ -12,6 +12,7 @@
 #define __MV88E6XXX_H
 
 #include <linux/if_vlan.h>
+#include <linux/gpio/consumer.h>
 
 #ifndef UINT64_MAX
 #define UINT64_MAX		(u64)(~((u64)0))
@@ -595,6 +596,12 @@ struct mv88e6xxx_priv_state {
 	DECLARE_BITMAP(port_state_update_mask, DSA_MAX_PORTS);
 
 	struct work_struct bridge_work;
+
+	/* A switch may have a GPIO line tied to its reset pin. Parse
+	 * this from the device tree, and use it before performing
+	 * switch soft reset.
+	 */
+	struct gpio_desc *reset;
 };
 
 enum stat_type {

include/net/dsa.h

@@ -16,7 +16,6 @@
 #include <linux/timer.h>
 #include <linux/workqueue.h>
 #include <linux/of.h>
-#include <linux/of_gpio.h>
 #include <linux/phy.h>
 #include <linux/phy_fixed.h>
 #include <linux/ethtool.h>
@@ -65,13 +64,6 @@ struct dsa_chip_data {
 	 * NULL if there is only one switch chip.
 	 */
 	s8		*rtable;
-
-	/*
-	 * A switch may have a GPIO line tied to its reset pin. Parse
-	 * this from the device tree, and use it before performing
-	 * switch soft reset.
-	 */
-	struct gpio_desc *reset;
 };
 
 struct dsa_platform_data {

net/dsa/dsa.c

@@ -659,9 +659,6 @@ static int dsa_of_probe(struct device *dev)
 	const char *port_name;
 	int chip_index, port_index;
 	const unsigned int *sw_addr, *port_reg;
-	int gpio;
-	enum of_gpio_flags of_flags;
-	unsigned long flags;
 	u32 eeprom_len;
 	int ret;
 
@@ -740,19 +737,6 @@ static int dsa_of_probe(struct device *dev)
 			put_device(cd->host_dev);
 			cd->host_dev = &mdio_bus_switch->dev;
 		}
-		gpio = of_get_named_gpio_flags(child, "reset-gpios", 0,
-					       &of_flags);
-		if (gpio_is_valid(gpio)) {
-			flags = (of_flags == OF_GPIO_ACTIVE_LOW ?
-				 GPIOF_ACTIVE_LOW : 0);
-			ret = devm_gpio_request_one(dev, gpio, flags,
-						    "switch_reset");
-			if (ret)
-				goto out_free_chip;
-
-			cd->reset = gpio_to_desc(gpio);
-			gpiod_direction_output(cd->reset, 0);
-		}
 
 		for_each_available_child_of_node(child, port) {
 			port_reg = of_get_property(port, "reg", NULL);