提交 486bc794 编写于 作者: L Linus Torvalds

Merge branch 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm2000: Fix use-after-free - don't release_firmware() twice on error
  ASoC: wm8958: Use correct format string in dev_err() call
  ASoC: wm8996: Call _POST_PMU callback for CPVDD
  ASoC: mxs: Fix mxs-saif timeout
  ASoC: Disable register synchronisation for low frequency WM8996 SYSCLK
  ASoC: Don't go through cache when applying WM5100 rev A updates
  ASoC: Mark WM5100 register map cache only when going into BIAS_OFF
  ASoC: tlv320aic32x4: always enable analouge block
  ASoC: tlv320aic32x4: always enable dividers
  ASoC: sgtl5000: Fix wrong register name in restore
......@@ -987,12 +987,12 @@ static int sgtl5000_restore_regs(struct snd_soc_codec *codec)
/* restore regular registers */
for (reg = 0; reg <= SGTL5000_CHIP_SHORT_CTRL; reg += 2) {
/* this regs depends on the others */
/* These regs should restore in particular order */
if (reg == SGTL5000_CHIP_ANA_POWER ||
reg == SGTL5000_CHIP_CLK_CTRL ||
reg == SGTL5000_CHIP_LINREG_CTRL ||
reg == SGTL5000_CHIP_LINE_OUT_CTRL ||
reg == SGTL5000_CHIP_CLK_CTRL)
reg == SGTL5000_CHIP_REF_CTRL)
continue;
snd_soc_write(codec, reg, cache[reg]);
......@@ -1003,8 +1003,17 @@ static int sgtl5000_restore_regs(struct snd_soc_codec *codec)
snd_soc_write(codec, reg, cache[reg]);
/*
* restore power and other regs according
* to set_power() and set_clock()
* restore these regs according to the power setting sequence in
* sgtl5000_set_power_regs() and clock setting sequence in
* sgtl5000_set_clock().
*
* The order of restore is:
* 1. SGTL5000_CHIP_CLK_CTRL MCLK_FREQ bits (1:0) should be restore after
* SGTL5000_CHIP_ANA_POWER PLL bits set
* 2. SGTL5000_CHIP_LINREG_CTRL should be set before
* SGTL5000_CHIP_ANA_POWER LINREG_D restored
* 3. SGTL5000_CHIP_REF_CTRL controls Analog Ground Voltage,
* prefer to resotre it after SGTL5000_CHIP_ANA_POWER restored
*/
snd_soc_write(codec, SGTL5000_CHIP_LINREG_CTRL,
cache[SGTL5000_CHIP_LINREG_CTRL]);
......
......@@ -60,7 +60,6 @@ struct aic32x4_rate_divs {
struct aic32x4_priv {
u32 sysclk;
s32 master;
u8 page_no;
void *control_data;
u32 power_cfg;
......@@ -369,7 +368,6 @@ static int aic32x4_set_dai_sysclk(struct snd_soc_dai *codec_dai,
static int aic32x4_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
{
struct snd_soc_codec *codec = codec_dai->codec;
struct aic32x4_priv *aic32x4 = snd_soc_codec_get_drvdata(codec);
u8 iface_reg_1;
u8 iface_reg_2;
u8 iface_reg_3;
......@@ -384,11 +382,9 @@ static int aic32x4_set_dai_fmt(struct snd_soc_dai *codec_dai, unsigned int fmt)
/* set master/slave audio interface */
switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
case SND_SOC_DAIFMT_CBM_CFM:
aic32x4->master = 1;
iface_reg_1 |= AIC32X4_BCLKMASTER | AIC32X4_WCLKMASTER;
break;
case SND_SOC_DAIFMT_CBS_CFS:
aic32x4->master = 0;
break;
default:
printk(KERN_ERR "aic32x4: invalid DAI master/slave interface\n");
......@@ -526,64 +522,58 @@ static int aic32x4_mute(struct snd_soc_dai *dai, int mute)
static int aic32x4_set_bias_level(struct snd_soc_codec *codec,
enum snd_soc_bias_level level)
{
struct aic32x4_priv *aic32x4 = snd_soc_codec_get_drvdata(codec);
switch (level) {
case SND_SOC_BIAS_ON:
if (aic32x4->master) {
/* Switch on PLL */
snd_soc_update_bits(codec, AIC32X4_PLLPR,
AIC32X4_PLLEN, AIC32X4_PLLEN);
/* Switch on NDAC Divider */
snd_soc_update_bits(codec, AIC32X4_NDAC,
AIC32X4_NDACEN, AIC32X4_NDACEN);
/* Switch on MDAC Divider */
snd_soc_update_bits(codec, AIC32X4_MDAC,
AIC32X4_MDACEN, AIC32X4_MDACEN);
/* Switch on NADC Divider */
snd_soc_update_bits(codec, AIC32X4_NADC,
AIC32X4_NADCEN, AIC32X4_NADCEN);
/* Switch on MADC Divider */
snd_soc_update_bits(codec, AIC32X4_MADC,
AIC32X4_MADCEN, AIC32X4_MADCEN);
/* Switch on BCLK_N Divider */
snd_soc_update_bits(codec, AIC32X4_BCLKN,
AIC32X4_BCLKEN, AIC32X4_BCLKEN);
}
/* Switch on PLL */
snd_soc_update_bits(codec, AIC32X4_PLLPR,
AIC32X4_PLLEN, AIC32X4_PLLEN);
/* Switch on NDAC Divider */
snd_soc_update_bits(codec, AIC32X4_NDAC,
AIC32X4_NDACEN, AIC32X4_NDACEN);
/* Switch on MDAC Divider */
snd_soc_update_bits(codec, AIC32X4_MDAC,
AIC32X4_MDACEN, AIC32X4_MDACEN);
/* Switch on NADC Divider */
snd_soc_update_bits(codec, AIC32X4_NADC,
AIC32X4_NADCEN, AIC32X4_NADCEN);
/* Switch on MADC Divider */
snd_soc_update_bits(codec, AIC32X4_MADC,
AIC32X4_MADCEN, AIC32X4_MADCEN);
/* Switch on BCLK_N Divider */
snd_soc_update_bits(codec, AIC32X4_BCLKN,
AIC32X4_BCLKEN, AIC32X4_BCLKEN);
break;
case SND_SOC_BIAS_PREPARE:
break;
case SND_SOC_BIAS_STANDBY:
if (aic32x4->master) {
/* Switch off PLL */
snd_soc_update_bits(codec, AIC32X4_PLLPR,
AIC32X4_PLLEN, 0);
/* Switch off NDAC Divider */
snd_soc_update_bits(codec, AIC32X4_NDAC,
AIC32X4_NDACEN, 0);
/* Switch off MDAC Divider */
snd_soc_update_bits(codec, AIC32X4_MDAC,
AIC32X4_MDACEN, 0);
/* Switch off NADC Divider */
snd_soc_update_bits(codec, AIC32X4_NADC,
AIC32X4_NADCEN, 0);
/* Switch off MADC Divider */
snd_soc_update_bits(codec, AIC32X4_MADC,
AIC32X4_MADCEN, 0);
/* Switch off BCLK_N Divider */
snd_soc_update_bits(codec, AIC32X4_BCLKN,
AIC32X4_BCLKEN, 0);
}
/* Switch off PLL */
snd_soc_update_bits(codec, AIC32X4_PLLPR,
AIC32X4_PLLEN, 0);
/* Switch off NDAC Divider */
snd_soc_update_bits(codec, AIC32X4_NDAC,
AIC32X4_NDACEN, 0);
/* Switch off MDAC Divider */
snd_soc_update_bits(codec, AIC32X4_MDAC,
AIC32X4_MDACEN, 0);
/* Switch off NADC Divider */
snd_soc_update_bits(codec, AIC32X4_NADC,
AIC32X4_NADCEN, 0);
/* Switch off MADC Divider */
snd_soc_update_bits(codec, AIC32X4_MADC,
AIC32X4_MADCEN, 0);
/* Switch off BCLK_N Divider */
snd_soc_update_bits(codec, AIC32X4_BCLKN,
AIC32X4_BCLKEN, 0);
break;
case SND_SOC_BIAS_OFF:
break;
......@@ -651,9 +641,11 @@ static int aic32x4_probe(struct snd_soc_codec *codec)
if (aic32x4->power_cfg & AIC32X4_PWR_AVDD_DVDD_WEAK_DISABLE) {
snd_soc_write(codec, AIC32X4_PWRCFG, AIC32X4_AVDDWEAKDISABLE);
}
if (aic32x4->power_cfg & AIC32X4_PWR_AIC32X4_LDO_ENABLE) {
snd_soc_write(codec, AIC32X4_LDOCTL, AIC32X4_LDOCTLEN);
}
tmp_reg = (aic32x4->power_cfg & AIC32X4_PWR_AIC32X4_LDO_ENABLE) ?
AIC32X4_LDOCTLEN : 0;
snd_soc_write(codec, AIC32X4_LDOCTL, tmp_reg);
tmp_reg = snd_soc_read(codec, AIC32X4_CMMODE);
if (aic32x4->power_cfg & AIC32X4_PWR_CMMODE_LDOIN_RANGE_18_36) {
tmp_reg |= AIC32X4_LDOIN_18_36;
......
......@@ -733,8 +733,9 @@ static int __devinit wm2000_i2c_probe(struct i2c_client *i2c,
struct wm2000_priv *wm2000;
struct wm2000_platform_data *pdata;
const char *filename;
const struct firmware *fw;
int reg, ret;
const struct firmware *fw = NULL;
int ret;
int reg;
u16 id;
wm2000 = devm_kzalloc(&i2c->dev, sizeof(struct wm2000_priv),
......@@ -751,7 +752,7 @@ static int __devinit wm2000_i2c_probe(struct i2c_client *i2c,
ret = PTR_ERR(wm2000->regmap);
dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
ret);
goto err;
goto out;
}
/* Verify that this is a WM2000 */
......@@ -763,7 +764,7 @@ static int __devinit wm2000_i2c_probe(struct i2c_client *i2c,
if (id != 0x2000) {
dev_err(&i2c->dev, "Device is not a WM2000 - ID %x\n", id);
ret = -ENODEV;
goto err_regmap;
goto out_regmap_exit;
}
reg = wm2000_read(i2c, WM2000_REG_REVISON);
......@@ -782,7 +783,7 @@ static int __devinit wm2000_i2c_probe(struct i2c_client *i2c,
ret = request_firmware(&fw, filename, &i2c->dev);
if (ret != 0) {
dev_err(&i2c->dev, "Failed to acquire ANC data: %d\n", ret);
goto err_regmap;
goto out_regmap_exit;
}
/* Pre-cook the concatenation of the register address onto the image */
......@@ -793,15 +794,13 @@ static int __devinit wm2000_i2c_probe(struct i2c_client *i2c,
if (wm2000->anc_download == NULL) {
dev_err(&i2c->dev, "Out of memory\n");
ret = -ENOMEM;
goto err_fw;
goto out_regmap_exit;
}
wm2000->anc_download[0] = 0x80;
wm2000->anc_download[1] = 0x00;
memcpy(wm2000->anc_download + 2, fw->data, fw->size);
release_firmware(fw);
wm2000->anc_eng_ena = 1;
wm2000->anc_active = 1;
wm2000->spk_ena = 1;
......@@ -809,18 +808,14 @@ static int __devinit wm2000_i2c_probe(struct i2c_client *i2c,
wm2000_reset(wm2000);
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000, NULL, 0);
if (!ret)
goto out;
return 0;
err_fw:
release_firmware(fw);
err_regmap:
out_regmap_exit:
regmap_exit(wm2000->regmap);
err:
out:
release_firmware(fw);
return ret;
}
......
......@@ -1377,6 +1377,7 @@ static int wm5100_set_bias_level(struct snd_soc_codec *codec,
switch (wm5100->rev) {
case 0:
regcache_cache_bypass(wm5100->regmap, true);
snd_soc_write(codec, 0x11, 0x3);
snd_soc_write(codec, 0x203, 0xc);
snd_soc_write(codec, 0x206, 0);
......@@ -1392,6 +1393,7 @@ static int wm5100_set_bias_level(struct snd_soc_codec *codec,
snd_soc_write(codec,
wm5100_reva_patches[i].reg,
wm5100_reva_patches[i].val);
regcache_cache_bypass(wm5100->regmap, false);
break;
default:
break;
......@@ -1402,6 +1404,7 @@ static int wm5100_set_bias_level(struct snd_soc_codec *codec,
break;
case SND_SOC_BIAS_OFF:
regcache_cache_only(wm5100->regmap, true);
if (wm5100->pdata.ldo_ena)
gpio_set_value_cansleep(wm5100->pdata.ldo_ena, 0);
regulator_bulk_disable(ARRAY_SIZE(wm5100->core_supplies),
......
......@@ -55,7 +55,7 @@ static int wm8958_dsp2_fw(struct snd_soc_codec *codec, const char *name,
return 0;
if (fw->size < 32) {
dev_err(codec->dev, "%s: firmware too short (%d bytes)\n",
dev_err(codec->dev, "%s: firmware too short (%zd bytes)\n",
name, fw->size);
goto err;
}
......
......@@ -1120,7 +1120,8 @@ SND_SOC_DAPM_SUPPLY_S("SYSCLK", 1, WM8996_AIF_CLOCKING_1, 0, 0, NULL, 0),
SND_SOC_DAPM_SUPPLY_S("SYSDSPCLK", 2, WM8996_CLOCKING_1, 1, 0, NULL, 0),
SND_SOC_DAPM_SUPPLY_S("AIFCLK", 2, WM8996_CLOCKING_1, 2, 0, NULL, 0),
SND_SOC_DAPM_SUPPLY_S("Charge Pump", 2, WM8996_CHARGE_PUMP_1, 15, 0, cp_event,
SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU |
SND_SOC_DAPM_POST_PMD),
SND_SOC_DAPM_SUPPLY("Bandgap", SND_SOC_NOPM, 0, 0, bg_event,
SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
SND_SOC_DAPM_SUPPLY("LDO2", WM8996_POWER_MANAGEMENT_2, 1, 0, NULL, 0),
......@@ -2007,6 +2008,7 @@ static int wm8996_set_sysclk(struct snd_soc_dai *dai,
struct wm8996_priv *wm8996 = snd_soc_codec_get_drvdata(codec);
int lfclk = 0;
int ratediv = 0;
int sync = WM8996_REG_SYNC;
int src;
int old;
......@@ -2051,6 +2053,7 @@ static int wm8996_set_sysclk(struct snd_soc_dai *dai,
case 32000:
case 32768:
lfclk = WM8996_LFCLK_ENA;
sync = 0;
break;
default:
dev_warn(codec->dev, "Unsupported clock rate %dHz\n",
......@@ -2064,6 +2067,8 @@ static int wm8996_set_sysclk(struct snd_soc_dai *dai,
WM8996_SYSCLK_SRC_MASK | WM8996_SYSCLK_DIV_MASK,
src << WM8996_SYSCLK_SRC_SHIFT | ratediv);
snd_soc_update_bits(codec, WM8996_CLOCKING_1, WM8996_LFCLK_ENA, lfclk);
snd_soc_update_bits(codec, WM8996_CONTROL_INTERFACE_1,
WM8996_REG_SYNC, sync);
snd_soc_update_bits(codec, WM8996_AIF_CLOCKING_1,
WM8996_SYSCLK_ENA, old);
......
......@@ -1567,6 +1567,10 @@ int wm8996_detect(struct snd_soc_codec *codec, struct snd_soc_jack *jack,
/*
* R257 (0x101) - Control Interface (1)
*/
#define WM8996_REG_SYNC 0x8000 /* REG_SYNC */
#define WM8996_REG_SYNC_MASK 0x8000 /* REG_SYNC */
#define WM8996_REG_SYNC_SHIFT 15 /* REG_SYNC */
#define WM8996_REG_SYNC_WIDTH 1 /* REG_SYNC */
#define WM8996_AUTO_INC 0x0004 /* AUTO_INC */
#define WM8996_AUTO_INC_MASK 0x0004 /* AUTO_INC */
#define WM8996_AUTO_INC_SHIFT 2 /* AUTO_INC */
......
......@@ -124,6 +124,8 @@ static int mxs_saif_set_clk(struct mxs_saif *saif,
*
* If MCLK is not used, we just set saif clk to 512*fs.
*/
clk_prepare_enable(master_saif->clk);
if (master_saif->mclk_in_use) {
if (mclk % 32 == 0) {
scr &= ~BM_SAIF_CTRL_BITCLK_BASE_RATE;
......@@ -133,6 +135,7 @@ static int mxs_saif_set_clk(struct mxs_saif *saif,
ret = clk_set_rate(master_saif->clk, 384 * rate);
} else {
/* SAIF MCLK should be either 32x or 48x */
clk_disable_unprepare(master_saif->clk);
return -EINVAL;
}
} else {
......@@ -140,6 +143,8 @@ static int mxs_saif_set_clk(struct mxs_saif *saif,
scr &= ~BM_SAIF_CTRL_BITCLK_BASE_RATE;
}
clk_disable_unprepare(master_saif->clk);
if (ret)
return ret;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册