Revert "serial: sccnxp: Add DT support"

This reverts commit 85c99690.

Alexander wishes to remove this patch as it is incorrect.
Reported-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/tty/serial/sccnxp-serial.txt

-* NXP (Philips) SCC+++(SCN+++) serial driver
-
-Required properties:
-- compatible: Should be "nxp,<ictype>". The supported ICs include sc2681,
-  sc2691, sc2692, sc2891, sc2892, sc28202, sc68681 and sc68692.
-- reg: Address and length of the register set for the device.
-- interrupts: Should contain the interrupt number. If omitted,
-  polling mode will be used instead, so "poll-interval" property should
-  be populated in this case.
-
-Optional properties:
-- clocks: Phandle to input clock. If omitted, default IC frequency will be
-  used instead.
-- poll-interval: Poll interval time in nanoseconds.
-- vcc-supply: The regulator supplying the VCC to drive the chip.
-- nxp,sccnxp-io-cfg: Array contains values for the emulated modem signals.
-  The number of values depends on the UART-number in the selected chip.
-  Each value should be composed according to the following rules:
-  (LINE1 << SIGNAL1) | ... | (LINEX << SIGNALX), where:
-   LINE - VALUE:
-    OP0 - 1
-    OP1 - 2
-    OP2 - 3
-    OP3 - 4
-    OP4 - 5
-    OP5 - 6
-    OP6 - 7
-    OP7 - 8
-    IP0 - 9
-    IP1 - 10
-    IP2 - 11
-    IP3 - 12
-    IP4 - 13
-    IP5 - 14
-    IP6 - 15
-   SIGNAL - VALUE:
-    DTR - 0
-    RTS - 4
-    DSR - 8
-    CTS - 12
-    DCD - 16
-    RNG - 20
-    DIR - 24
-
-Example (Dual UART with direction control on OP0 & OP1):
-sc2892@10100000 {
-	compatible = "nxp,sc2892";
-	reg = <0x10100000 0x10>;
-	poll-interval = <10000>;
-	clocks = <&sc2892_clk>;
-	vcc-supply = <&sc2892_reg>;
-	nxp,sccnxp-io-cfg = <0x01000000 0x02000000>;
-};

drivers/tty/serial/sccnxp.c

@@ -20,8 +20,6 @@
 #include <linux/module.h>
 #include <linux/device.h>
 #include <linux/console.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
 #include <linux/serial_core.h>
 #include <linux/serial.h>
 #include <linux/io.h>
@@ -855,25 +853,10 @@ static const struct platform_device_id sccnxp_id_table[] = {
 };
 MODULE_DEVICE_TABLE(platform, sccnxp_id_table);
 
-static const struct of_device_id sccnxp_dt_id_table[] = {
-	{ .compatible = "nxp,sc2681",	.data = &sc2681, },
-	{ .compatible = "nxp,sc2691",	.data = &sc2691, },
-	{ .compatible = "nxp,sc2692",	.data = &sc2692, },
-	{ .compatible = "nxp,sc2891",	.data = &sc2891, },
-	{ .compatible = "nxp,sc2892",	.data = &sc2892, },
-	{ .compatible = "nxp,sc28202",	.data = &sc28202, },
-	{ .compatible = "nxp,sc68681",	.data = &sc68681, },
-	{ .compatible = "nxp,sc68692",	.data = &sc68692, },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, sccnxp_dt_id_table);
-
 static int sccnxp_probe(struct platform_device *pdev)
 {
 	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	struct sccnxp_pdata *pdata = dev_get_platdata(&pdev->dev);
-	const struct of_device_id *of_id =
-		of_match_device(sccnxp_dt_id_table, &pdev->dev);
 	int i, ret, uartclk;
 	struct sccnxp_port *s;
 	void __iomem *membase;
@@ -892,22 +875,7 @@ static int sccnxp_probe(struct platform_device *pdev)
 
 	spin_lock_init(&s->lock);
 
-	if (of_id) {
-		s->chip = (struct sccnxp_chip *)of_id->data;
-
-		of_property_read_u32(pdev->dev.of_node, "poll-interval",
-				     &s->pdata.poll_time_us);
-		of_property_read_u32(pdev->dev.of_node, "reg-shift",
-				     &s->pdata.reg_shift);
-		of_property_read_u32_array(pdev->dev.of_node,
-					   "nxp,sccnxp-io-cfg",
-					   s->pdata.mctrl_cfg, s->chip->nr);
-	} else {
-		s->chip = (struct sccnxp_chip *)pdev->id_entry->driver_data;
-
-		if (pdata)
-			memcpy(&s->pdata, pdata, sizeof(struct sccnxp_pdata));
-	}
+	s->chip = (struct sccnxp_chip *)pdev->id_entry->driver_data;
 
 	s->regulator = devm_regulator_get(&pdev->dev, "vcc");
 	if (!IS_ERR(s->regulator)) {
@@ -938,11 +906,16 @@ static int sccnxp_probe(struct platform_device *pdev)
 		goto err_out;
 	}
 
+	if (pdata)
+		memcpy(&s->pdata, pdata, sizeof(struct sccnxp_pdata));
+
 	if (s->pdata.poll_time_us) {
 		dev_info(&pdev->dev, "Using poll mode, resolution %u usecs\n",
 			 s->pdata.poll_time_us);
 		s->poll = 1;
-	} else {
+	}
+
+	if (!s->poll) {
 		s->irq = platform_get_irq(pdev, 0);
 		if (s->irq < 0) {
 			dev_err(&pdev->dev, "Missing irq resource data\n");
@@ -1043,9 +1016,8 @@ static int sccnxp_remove(struct platform_device *pdev)
 
 static struct platform_driver sccnxp_uart_driver = {
 	.driver = {
-		.name		= SCCNXP_NAME,
-		.owner		= THIS_MODULE,
-		.of_match_table	= sccnxp_dt_id_table,
+		.name	= SCCNXP_NAME,
+		.owner	= THIS_MODULE,
 	},
 	.probe		= sccnxp_probe,
 	.remove		= sccnxp_remove,

include/linux/platform_data/serial-sccnxp.h

@@ -78,11 +78,11 @@
 /* SCCNXP platform data structure */
 struct sccnxp_pdata {
 	/* Shift for A0 line */
-	u32	reg_shift;
+	const u8		reg_shift;
 	/* Modem control lines configuration */
-	u32	mctrl_cfg[SCCNXP_MAX_UARTS];
+	const u32		mctrl_cfg[SCCNXP_MAX_UARTS];
 	/* Timer value for polling mode (usecs) */
-	u32	poll_time_us;
+	const unsigned int	poll_time_us;
 };
 
 #endif