[PATCH] CRIS update: configuration and build

Changes to configuration and build system. * Added v32 sub architecture. * Use generic hard IRQ. * Added SMP options. * Added options to OOPS at NMI and reboot at OOM. * Made it possible to set objtree. * Added option to select Kernel GDB serial port. * Corrected Kconfig usage. * Added system profiler. Signed-off-by: N Mikael Starvik <starvik@axis.com> Signed-off-by: N Andrew Morton <akpm@osdl.org> Signed-off-by: N Linus Torvalds <torvalds@osdl.org>

[PATCH] CRIS update: configuration and build
Changes to configuration and build system. * Added v32 sub architecture. * Use generic hard IRQ. * Added SMP options. * Added options to OOPS at NMI and reboot at OOM. * Made it possible to set objtree. * Added option to select Kernel GDB serial port. * Corrected Kconfig usage. * Added system profiler. Signed-off-by: N Mikael Starvik <starvik@axis.com> Signed-off-by: N Andrew Morton <akpm@osdl.org> Signed-off-by: N Linus Torvalds <torvalds@osdl.org>
3e41d652 · Mikael Starvik · Linus Torvalds · cb09f540 · 3e41d652 · 3e41d652
9 changed file
--- a/arch/cris/Kconfig.debug
+++ b/arch/cris/Kconfig.debug
@@ -38,4 +38,9 @@ config FRAME_POINTER
          If you don't debug the kernel, you can say N, but we may not be able
          to solve problems without frame pointers.

+config DEBUG_NMI_OOPS
+       bool "NMI causes oops printout"
+       help
+         If the system locks up without any debug information you can say Y
+         here to make it possible to dump an OOPS with an external NMI.
 endmenu
--- a/arch/cris/Makefile
+++ b/arch/cris/Makefile
-# $Id: Makefile,v 1.23 2004/10/19 13:07:34 starvik Exp $
+# $Id: Makefile,v 1.28 2005/03/17 10:44:37 larsv Exp $
 # cris/Makefile
 #
 # This file is included by the global makefile so that you can add your own
@@ -15,6 +15,7 @@

 arch-y := v10
 arch-$(CONFIG_ETRAX_ARCH_V10) := v10
+arch-$(CONFIG_ETRAX_ARCH_V32) := v32

 # No config avaiable for make clean etc
 ifneq ($(arch-y),)
@@ -46,6 +47,21 @@ core-y		+= arch/$(ARCH)/$(SARCH)/kernel/ arch/$(ARCH)/$(SARCH)/mm/
 drivers-y	+= arch/$(ARCH)/$(SARCH)/drivers/
 libs-y		+= arch/$(ARCH)/$(SARCH)/lib/ $(LIBGCC)

+# cris source path
+SRC_ARCH              = $(srctree)/arch/$(ARCH)
+# cris object files path
+OBJ_ARCH              = $(objtree)/arch/$(ARCH)
+
+target_boot_arch_dir  = $(OBJ_ARCH)/$(SARCH)/boot
+target_boot_dir       = $(OBJ_ARCH)/boot
+src_boot_dir          = $(SRC_ARCH)/boot
+target_compressed_dir = $(OBJ_ARCH)/boot/compressed
+src_compressed_dir    = $(SRC_ARCH)/boot/compressed
+target_rescue_dir     = $(OBJ_ARCH)/boot/rescue
+src_rescue_dir        = $(SRC_ARCH)/boot/rescue
+
+export target_boot_arch_dir target_boot_dir src_boot_dir target_compressed_dir src_compressed_dir target_rescue_dir src_rescue_dir
+
 vmlinux.bin: vmlinux
 	$(OBJCOPY) $(OBJCOPYFLAGS) vmlinux vmlinux.bin

@@ -65,44 +81,52 @@ cramfs:

 clinux: vmlinux.bin decompress.bin rescue.bin

-decompress.bin: FORCE
-	@make -C arch/$(ARCH)/boot/compressed decompress.bin
+decompress.bin: $(target_boot_dir)
+	@$(MAKE) -f $(src_compressed_dir)/Makefile $(target_compressed_dir)/decompress.bin

-rescue.bin: FORCE
-	@make -C arch/$(ARCH)/boot/rescue rescue.bin
+$(target_rescue_dir)/rescue.bin: $(target_boot_dir)
+	@$(MAKE) -f $(src_rescue_dir)/Makefile $(target_rescue_dir)/rescue.bin

-zImage: vmlinux.bin rescue.bin
+zImage: $(target_boot_dir) vmlinux.bin $(target_rescue_dir)/rescue.bin
 ## zImage     - Compressed kernel (gzip)
-	@make -C arch/$(ARCH)/boot/ zImage
+	@$(MAKE) -f $(src_boot_dir)/Makefile zImage
+
+$(target_boot_dir): $(target_boot_arch_dir)
+	ln -sfn $< $@
+
+$(target_boot_arch_dir):
+	mkdir -p $@

 compressed: zImage

 archmrproper:
 archclean:
-	$(Q)$(MAKE) $(clean)=arch/$(ARCH)/boot
+	@if [ -d arch/$(ARCH)/boot ]; then \
+		$(MAKE) $(clean)=arch/$(ARCH)/boot ; \
+	fi
 	rm -f timage vmlinux.bin decompress.bin rescue.bin cramfs.img
 	rm -rf $(LD_SCRIPT).tmp

-prepare: arch/$(ARCH)/.links include/asm-$(ARCH)/.arch \
+prepare: $(SRC_ARCH)/.links $(srctree)/include/asm-$(ARCH)/.arch \
 	 include/asm-$(ARCH)/$(SARCH)/offset.h

 # Create some links to make all tools happy
-arch/$(ARCH)/.links:
-	@rm -rf arch/$(ARCH)/drivers
-	@ln -sfn $(SARCH)/drivers arch/$(ARCH)/drivers
-	@rm -rf arch/$(ARCH)/boot
-	@ln -sfn $(SARCH)/boot arch/$(ARCH)/boot
-	@rm -rf arch/$(ARCH)/lib
-	@ln -sfn $(SARCH)/lib arch/$(ARCH)/lib
-	@ln -sfn $(SARCH) arch/$(ARCH)/arch
-	@ln -sfn ../$(SARCH)/vmlinux.lds.S arch/$(ARCH)/kernel/vmlinux.lds.S
+$(SRC_ARCH)/.links:
+	@rm -rf $(SRC_ARCH)/drivers
+	@ln -sfn $(SRC_ARCH)/$(SARCH)/drivers $(SRC_ARCH)/drivers
+	@rm -rf $(SRC_ARCH)/boot
+	@ln -sfn $(SRC_ARCH)/$(SARCH)/boot $(SRC_ARCH)/boot
+	@rm -rf $(SRC_ARCH)/lib
+	@ln -sfn $(SRC_ARCH)/$(SARCH)/lib $(SRC_ARCH)/lib
+	@ln -sfn $(SRC_ARCH)/$(SARCH) $(SRC_ARCH)/arch
+	@ln -sfn $(SRC_ARCH)/$(SARCH)/vmlinux.lds.S $(SRC_ARCH)/kernel/vmlinux.lds.S
 	@touch $@

 # Create link to sub arch includes
-include/asm-$(ARCH)/.arch: $(wildcard include/config/arch/*.h)
-	@echo '  Making asm-$(ARCH)/arch -> asm-$(ARCH)/$(SARCH) symlink'
+$(srctree)/include/asm-$(ARCH)/.arch: $(wildcard include/config/arch/*.h)
+	@echo '  Making $(srctree)/include/asm-$(ARCH)/arch -> $(srctree)/include/asm-$(ARCH)/$(SARCH) symlink'
 	@rm -f include/asm-$(ARCH)/arch
-	@ln -sf $(SARCH) include/asm-$(ARCH)/arch
+	@ln -sf $(srctree)/include/asm-$(ARCH)/$(SARCH) $(srctree)/include/asm-$(ARCH)/arch
 	@touch $@

 arch/$(ARCH)/$(SARCH)/kernel/asm-offsets.s: include/asm include/linux/version.h \

--- a/arch/cris/arch-v10/Kconfig
+++ b/arch/cris/arch-v10/Kconfig
@@ -259,6 +259,37 @@ config ETRAX_DEBUG_PORT_NULL

 endchoice

+choice
+	prompt "Kernel GDB port"
+	depends on ETRAX_KGDB
+	default ETRAX_KGDB_PORT0
+	help
+	  Choose a serial port for kernel debugging.  NOTE: This port should
+	  not be enabled under Drivers for built-in interfaces (as it has its
+	  own initialization code) and should not be the same as the debug port.
+
+config ETRAX_KGDB_PORT0
+	bool "Serial-0"
+	help
+	  Use serial port 0 for kernel debugging.
+
+config ETRAX_KGDB_PORT1
+	bool "Serial-1"
+	help
+	  Use serial port 1 for kernel debugging.
+
+config ETRAX_KGDB_PORT2
+	bool "Serial-2"
+	help
+	  Use serial port 2 for kernel debugging.
+
+config ETRAX_KGDB_PORT3
+	bool "Serial-3"
+	help
+	  Use serial port 3 for kernel debugging.
+
+endchoice
+
 choice
 	prompt "Product rescue-port"
 	depends on ETRAX_ARCH_V10

--- a/arch/cris/arch-v10/boot/Makefile
+++ b/arch/cris/arch-v10/boot/Makefile
 #
 # arch/cris/boot/Makefile
 #
+target = $(target_boot_dir)
+src    = $(src_boot_dir)

 zImage: compressed/vmlinuz

-compressed/vmlinuz: $(TOPDIR)/vmlinux
-	@$(MAKE) -C compressed vmlinuz
+compressed/vmlinuz:
+	@$(MAKE) -f $(src)/compressed/Makefile $(target_compressed_dir)/vmlinuz

 clean:
-	rm -f zImage tools/build compressed/vmlinux.out
-	@$(MAKE) -C compressed clean
+	@$(MAKE) -f $(src)/compressed/Makefile clean
--- a/arch/cris/arch-v10/boot/compressed/Makefile
+++ b/arch/cris/arch-v10/boot/compressed/Makefile
 #
-# linux/arch/etrax100/boot/compressed/Makefile
-#
-# create a compressed vmlinux image from the original vmlinux files and romfs
+# create a compressed vmlinuz image from the binary vmlinux.bin file
 #
+target = $(target_compressed_dir)
+src    = $(src_compressed_dir)

-CC = gcc-cris -melf -I $(TOPDIR)/include
+CC = gcc-cris -melf $(LINUXINCLUDE)
 CFLAGS = -O2
 LD = ld-cris
 OBJCOPY = objcopy-cris
 OBJCOPYFLAGS = -O binary --remove-section=.bss
-OBJECTS = head.o misc.o
+OBJECTS = $(target)/head.o $(target)/misc.o

 # files to compress
-SYSTEM = $(TOPDIR)/vmlinux.bin
+SYSTEM = $(objtree)/vmlinux.bin

-all: vmlinuz
+all: $(target_compressed_dir)/vmlinuz

-decompress.bin: $(OBJECTS)
-	$(LD) -T decompress.ld -o decompress.o $(OBJECTS)
-	$(OBJCOPY) $(OBJCOPYFLAGS) decompress.o decompress.bin
-# save it for mkprod in the topdir.
-	cp decompress.bin $(TOPDIR)
+$(target)/decompress.bin: $(OBJECTS)
+	$(LD) -T $(src)/decompress.ld -o $(target)/decompress.o $(OBJECTS)
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/decompress.o $(target)/decompress.bin

+# Create vmlinuz image in top-level build directory
+$(target_compressed_dir)/vmlinuz: $(target) piggy.img $(target)/decompress.bin
+	@echo "  COMPR   vmlinux.bin --> vmlinuz"
+	@cat $(target)/decompress.bin piggy.img > $(target_compressed_dir)/vmlinuz
+	@rm -f piggy.img

-vmlinuz: piggy.img decompress.bin
-	cat decompress.bin piggy.img > vmlinuz
-	rm -f piggy.img
+$(target)/head.o: $(src)/head.S
+	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $@

-head.o: head.S
-	$(CC) -D__ASSEMBLY__ -traditional -c head.S -o head.o
+$(target)/misc.o: $(src)/misc.c
+	$(CC) -D__KERNEL__ -c $< -o $@

 # gzip the kernel image

 piggy.img: $(SYSTEM)
-	cat $(SYSTEM) | gzip -f -9 > piggy.img
+	@cat $(SYSTEM) | gzip -f -9 > piggy.img
+
+$(target):
+	mkdir -p $(target)

 clean:
-	rm -f piggy.img vmlinuz vmlinuz.o
+	rm -f piggy.img $(objtree)/vmlinuz

--- a/arch/cris/arch-v10/boot/rescue/Makefile
+++ b/arch/cris/arch-v10/boot/rescue/Makefile
 #
 # Makefile for rescue code
 #
-ifndef TOPDIR
-TOPDIR = ../../../..
-endif
-CC = gcc-cris -mlinux -I $(TOPDIR)/include
+target = $(target_rescue_dir)
+src    = $(src_rescue_dir)
+
+CC = gcc-cris -mlinux $(LINUXINCLUDE)
 CFLAGS = -O2
 LD = gcc-cris -mlinux -nostdlib
 OBJCOPY = objcopy-cris
 OBJCOPYFLAGS = -O binary --remove-section=.bss

-all: rescue.bin testrescue.bin kimagerescue.bin
-
-rescue: rescue.bin
-	# do nothing
+all: $(target)/rescue.bin $(target)/testrescue.bin $(target)/kimagerescue.bin

-rescue.bin: head.o
-	$(LD) -T rescue.ld -o rescue.o head.o
-	$(OBJCOPY) $(OBJCOPYFLAGS) rescue.o rescue.bin
-	cp rescue.bin $(TOPDIR)
+$(target)/rescue.bin: $(target) $(target)/head.o
+	$(LD) -T $(src)/rescue.ld -o $(target)/rescue.o $(target)/head.o
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/rescue.o $(target)/rescue.bin
+# Place a copy in top-level build directory
+	cp -p $(target)/rescue.bin $(objtree)

-testrescue.bin: testrescue.o
-	$(OBJCOPY) $(OBJCOPYFLAGS) testrescue.o tr.bin
+$(target)/testrescue.bin: $(target) $(target)/testrescue.o
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/testrescue.o tr.bin
 # Pad it to 784 bytes
 	dd if=/dev/zero of=tmp2423 bs=1 count=784
 	cat tr.bin tmp2423 >testrescue_tmp.bin
-	dd if=testrescue_tmp.bin of=testrescue.bin bs=1 count=784
+	dd if=testrescue_tmp.bin of=$(target)/testrescue.bin bs=1 count=784
 	rm tr.bin tmp2423 testrescue_tmp.bin

-kimagerescue.bin: kimagerescue.o
-	$(OBJCOPY) $(OBJCOPYFLAGS) kimagerescue.o ktr.bin
+$(target)/kimagerescue.bin: $(target) $(target)/kimagerescue.o
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/kimagerescue.o ktr.bin
 # Pad it to 784 bytes, that's what the rescue loader expects
 	dd if=/dev/zero of=tmp2423 bs=1 count=784
 	cat ktr.bin tmp2423 >kimagerescue_tmp.bin
-	dd if=kimagerescue_tmp.bin of=kimagerescue.bin bs=1 count=784
+	dd if=kimagerescue_tmp.bin of=$(target)/kimagerescue.bin bs=1 count=784
 	rm ktr.bin tmp2423 kimagerescue_tmp.bin

-head.o: head.S
+$(target):
+	mkdir -p $(target)
+
+$(target)/head.o: $(src)/head.S
 	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o

-testrescue.o: testrescue.S
+$(target)/testrescue.o: $(src)/testrescue.S
 	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o

-kimagerescue.o: kimagerescue.S
+$(target)/kimagerescue.o: $(src)/kimagerescue.S
 	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o

 clean:
-	rm -f *.o *.bin
+	rm -f $(target)/*.o $(target)/*.bin

 fastdep:


--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
 config ETRAX_ETHERNET
 	bool "Ethernet support"
 	depends on ETRAX_ARCH_V10
+	select NET_ETHERNET
 	help
 	  This option enables the ETRAX 100LX built-in 10/100Mbit Ethernet
 	  controller.

-# this is just so that the user does not have to go into the
-# normal ethernet driver section just to enable ethernetworking
-config NET_ETHERNET
-	bool
-	depends on ETRAX_ETHERNET
-	default y
-
 choice
 	prompt "Network LED behavior"
 	depends on ETRAX_ETHERNET
@@ -20,26 +14,26 @@ choice
 config ETRAX_NETWORK_LED_ON_WHEN_LINK
 	bool "LED_on_when_link"
 	help
-	  Selecting LED_on_when_link will light the LED when there is a 
-	  connection and will flash off when there is activity. 
+	  Selecting LED_on_when_link will light the LED when there is a
+	  connection and will flash off when there is activity.

-	  Selecting LED_on_when_activity will light the LED only when 
+	  Selecting LED_on_when_activity will light the LED only when
 	  there is activity.

-	  This setting will also affect the behaviour of other activity LEDs 
-	  e.g. Bluetooth. 
+	  This setting will also affect the behaviour of other activity LEDs
+	  e.g. Bluetooth.

 config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
 	bool "LED_on_when_activity"
 	help
-	  Selecting LED_on_when_link will light the LED when there is a 
-	  connection and will flash off when there is activity. 
+	  Selecting LED_on_when_link will light the LED when there is a
+	  connection and will flash off when there is activity.

-	  Selecting LED_on_when_activity will light the LED only when 
+	  Selecting LED_on_when_activity will light the LED only when
 	  there is activity.

-	  This setting will also affect the behaviour of other activity LEDs 
-	  e.g. Bluetooth. 
+	  This setting will also affect the behaviour of other activity LEDs
+	  e.g. Bluetooth.

 endchoice

@@ -91,11 +85,11 @@ choice
 	depends on ETRAX_SERIAL_PORT0
 	default ETRAX_SERIAL_PORT0_DMA6_OUT

-config CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT0_NO_DMA_OUT
+	bool "No DMA out"

-config CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT
-       bool "DMA 6"
+config ETRAX_SERIAL_PORT0_DMA6_OUT
+	bool "DMA 6"

 endchoice

@@ -104,11 +98,11 @@ choice
 	depends on ETRAX_SERIAL_PORT0
 	default ETRAX_SERIAL_PORT0_DMA7_IN

-config CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT0_NO_DMA_IN
+	bool "No DMA in"

-config CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN
-       bool "DMA 7"
+config ETRAX_SERIAL_PORT0_DMA7_IN
+	bool "DMA 7"

 endchoice

@@ -205,11 +199,11 @@ choice
 	depends on ETRAX_SERIAL_PORT1
 	default ETRAX_SERIAL_PORT1_DMA8_OUT

-config CONFIG_ETRAX_SERIAL_PORT1_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT1_NO_DMA_OUT
+	bool "No DMA out"

-config CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT
-       bool "DMA 8"
+config ETRAX_SERIAL_PORT1_DMA8_OUT
+	bool "DMA 8"

 endchoice

@@ -218,11 +212,11 @@ choice
 	depends on ETRAX_SERIAL_PORT1
 	default ETRAX_SERIAL_PORT1_DMA9_IN

-config CONFIG_ETRAX_SERIAL_PORT1_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT1_NO_DMA_IN
+	bool "No DMA in"

-config CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN
-       bool "DMA 9"
+config ETRAX_SERIAL_PORT1_DMA9_IN
+	bool "DMA 9"

 endchoice

@@ -308,7 +302,7 @@ config ETRAX_SER1_CD_ON_PB_BIT
 	  Specify the pin of the PB port to carry the CD signal for serial
 	  port 1.

-comment "Make sure you dont have the same PB bits more than once!"
+comment "Make sure you do not have the same PB bits more than once!"
 	depends on ETRAX_SERIAL && ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && ETRAX_SER1_DTR_RI_DSR_CD_ON_PB

 config ETRAX_SERIAL_PORT2
@@ -322,11 +316,11 @@ choice
 	depends on ETRAX_SERIAL_PORT2
 	default ETRAX_SERIAL_PORT2_DMA2_OUT

-config CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT2_NO_DMA_OUT
+	bool "No DMA out"

-config CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT
-       bool "DMA 2"
+config ETRAX_SERIAL_PORT2_DMA2_OUT
+	bool "DMA 2"

 endchoice

@@ -335,11 +329,11 @@ choice
 	depends on ETRAX_SERIAL_PORT2
 	default ETRAX_SERIAL_PORT2_DMA3_IN

-config CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT2_NO_DMA_IN
+	bool "No DMA in"

-config CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN
-       bool "DMA 3"
+config ETRAX_SERIAL_PORT2_DMA3_IN
+	bool "DMA 3"

 endchoice

@@ -436,11 +430,11 @@ choice
 	depends on ETRAX_SERIAL_PORT3
 	default ETRAX_SERIAL_PORT3_DMA4_OUT

-config CONFIG_ETRAX_SERIAL_PORT3_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT3_NO_DMA_OUT
+	bool "No DMA out"

-config CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT
-       bool "DMA 4"
+config ETRAX_SERIAL_PORT3_DMA4_OUT
+	bool "DMA 4"

 endchoice

@@ -449,11 +443,11 @@ choice
 	depends on ETRAX_SERIAL_PORT3
 	default ETRAX_SERIAL_PORT3_DMA5_IN

-config CONFIG_ETRAX_SERIAL_PORT3_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT3_NO_DMA_IN
+	bool "No DMA in"

-config CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN
-       bool "DMA 5"
+config ETRAX_SERIAL_PORT3_DMA5_IN
+	bool "DMA 5"

 endchoice

@@ -554,7 +548,6 @@ config ETRAX_IDE
 	select BLK_DEV_IDEDISK
 	select BLK_DEV_IDECD
 	select BLK_DEV_IDEDMA
-	select DMA_NONPCI
 	help
 	  Enable this to get support for ATA/IDE.
 	  You can't use paralell ports or SCSI ports
@@ -579,7 +572,7 @@ config ETRAX_IDE_PB7_RESET
 	  IDE reset on pin 7 on port B

 config ETRAX_IDE_G27_RESET
-        bool "Port_G_Bit_27"
+	bool "Port_G_Bit_27"
 	help
 	  IDE reset on pin 27 on port G

@@ -588,30 +581,36 @@ endchoice

 config ETRAX_USB_HOST
 	bool "USB host"
+	select USB
 	help
 	   This option enables the host functionality of the ETRAX 100LX
 	   built-in USB controller. In host mode the controller is designed
 	   for CTRL and BULK traffic only, INTR traffic may work as well
 	   however (depending on the requirements of timeliness).

-config USB
-       tristate
-       depends on ETRAX_USB_HOST
-       default y
-
 config ETRAX_USB_HOST_PORT1
-       bool "  USB port 1 enabled"
-       depends on ETRAX_USB_HOST
-       default n
+	bool "USB port 1 enabled"
+	depends on ETRAX_USB_HOST
+	default n

 config ETRAX_USB_HOST_PORT2
-       bool "  USB port 2 enabled"
-       depends on ETRAX_USB_HOST
-       default n
+	bool "USB port 2 enabled"
+	depends on ETRAX_USB_HOST
+	default n

 config ETRAX_AXISFLASHMAP
 	bool "Axis flash-map support"
 	depends on ETRAX_ARCH_V10
+	select MTD
+	select MTD_CFI
+	select MTD_CFI_AMDSTD
+	select MTD_OBSOLETE_CHIPS
+	select MTD_AMDSTD
+	select MTD_CHAR
+	select MTD_BLOCK
+	select MTD_PARTITIONS
+	select MTD_CONCAT
+	select MTD_COMPLEX_MAPPINGS
 	help
 	  This option enables MTD mapping of flash devices.  Needed to use
 	  flash memories.  If unsure, say Y.
@@ -627,119 +626,6 @@ config ETRAX_PTABLE_SECTOR
 	  for changing this is when the flash block size is bigger
 	  than 64kB (e.g. when using two parallel 16 bit flashes).

-# here we define the CONFIG_'s necessary to enable MTD support
-# for the flash
-config MTD
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  Memory Technology Devices are flash, RAM and similar chips, often
-	  used for solid state file systems on embedded devices. This option
-	  will provide the generic support for MTD drivers to register
-	  themselves with the kernel and for potential users of MTD devices
-	  to enumerate the devices which are present and obtain a handle on
-	  them. It will also allow you to select individual drivers for 
-	  particular hardware and users of MTD devices. If unsure, say N.
-
-config MTD_CFI
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  The Common Flash Interface specification was developed by Intel,
-	  AMD and other flash manufactures that provides a universal method
-	  for probing the capabilities of flash devices. If you wish to
-	  support any device that is CFI-compliant, you need to enable this
-	  option. Visit <http://www.amd.com/products/nvd/overview/cfi.html>
-	  for more information on CFI.
-
-config MTD_CFI_AMDSTD
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  The Common Flash Interface defines a number of different command
-	  sets which a CFI-compliant chip may claim to implement. This code
-	  provides support for one of those command sets, used on chips 
-	  chips including the AMD Am29LV320.
-
-config MTD_OBSOLETE_CHIPS
-	bool
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  This option does not enable any code directly, but will allow you to
-	  select some other chip drivers which are now considered obsolete,
-	  because the generic CONFIG_JEDEC_PROBE code above should now detect
-	  the chips which are supported by these drivers, and allow the generic
-	  CFI-compatible drivers to drive the chips. Say 'N' here unless you have
-	  already tried the CONFIG_JEDEC_PROBE method and reported its failure
-	  to the MTD mailing list at <linux-mtd@lists.infradead.org>
-
-config MTD_AMDSTD
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  This option enables support for flash chips using AMD-compatible
-	  commands, including some which are not CFI-compatible and hence 
-	  cannot be used with the CONFIG_MTD_CFI_AMDSTD option.
-
-	  It also works on AMD compatible chips that do conform to CFI.
-
-config MTD_CHAR
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  This provides a character device for each MTD device present in
-	  the system, allowing the user to read and write directly to the
-	  memory chips, and also use ioctl() to obtain information about
-	  the device, or to erase parts of it.
-
-config MTD_BLOCK
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	---help---
-	  Although most flash chips have an erase size too large to be useful
-	  as block devices, it is possible to use MTD devices which are based
-	  on RAM chips in this manner. This block device is a user of MTD
-	  devices performing that function.
-
-	  At the moment, it is also required for the Journalling Flash File
-	  System(s) to obtain a handle on the MTD device when it's mounted
-	  (although JFFS and JFFS2 don't actually use any of the functionality
-	  of the mtdblock device).
-
-	  Later, it may be extended to perform read/erase/modify/write cycles
-	  on flash chips to emulate a smaller block size. Needless to say,
-	  this is very unsafe, but could be useful for file systems which are
-	  almost never written to.
-
-	  You do not need this option for use with the DiskOnChip devices. For
-	  those, enable NFTL support (CONFIG_NFTL) instead.
-
-config MTD_PARTITIONS
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  If you have a device which needs to divide its flash chip(s) up
-	  into multiple 'partitions', each of which appears to the user as
-	  a separate MTD device, you require this option to be enabled. If
-	  unsure, say 'Y'.
-
-	  Note, however, that you don't need this option for the DiskOnChip
-	  devices. Partitioning on NFTL 'devices' is a different - that's the
-	  'normal' form of partitioning used on a block device.
-
-config MTD_CONCAT
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-
 config ETRAX_I2C
 	bool "I2C support"
 	depends on ETRAX_ARCH_V10
@@ -752,7 +638,7 @@ config ETRAX_I2C
 	  val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg);

 # this is true for most products since PB-I2C seems to be somewhat
-# flawed.. 
+# flawed..
 config ETRAX_I2C_USES_PB_NOT_PB_I2C
 	bool "I2C uses PB not PB-I2C"
 	depends on ETRAX_I2C
@@ -886,7 +772,7 @@ config ETRAX_RTC
 	bool "Real Time Clock support"
 	depends on ETRAX_ARCH_V10
 	help
-	  Enables drivers for the Real-Time Clock battery-backed chips on 
+	  Enables drivers for the Real-Time Clock battery-backed chips on
 	  some products. The kernel reads the time when booting, and
 	  the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a
 	  rtc_time struct (see <file:include/asm-cris/rtc.h>) on the /dev/rtc
@@ -903,13 +789,13 @@ config ETRAX_DS1302
 	bool "DS1302"
 	help
 	  Enables the driver for the DS1302 Real-Time Clock battery-backed
-	  chip on some products. 
+	  chip on some products.

 config ETRAX_PCF8563
 	bool "PCF8563"
 	help
 	  Enables the driver for the PCF8563 Real-Time Clock battery-backed
-	  chip on some products.  
+	  chip on some products.

 endchoice

@@ -954,10 +840,8 @@ config ETRAX_DS1302_TRICKLE_CHARGE
 	help
 	  This controls the initial value of the trickle charge register.
 	  0 = disabled (use this if you are unsure or have a non rechargable battery)
-	  Otherwise the following values can be OR:ed together to control the 
+	  Otherwise the following values can be OR:ed together to control the
 	  charge current:
 	  1 = 2kohm, 2 = 4kohm, 3 = 4kohm
 	  4 = 1 diode, 8 = 2 diodes
 	  Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5
-
-
--- a/arch/cris/defconfig
+++ b/arch/cris/defconfig
 #
 # Automatically generated make config: don't edit
+# Linux kernel version: 2.6.11
+# Mon Jun 20 13:42:02 2005
 #
 CONFIG_MMU=y
 CONFIG_UID16=y
 CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_GENERIC_IOMAP=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_CRIS=y

 #
 # Code maturity level options
 #
 CONFIG_EXPERIMENTAL=y
 CONFIG_CLEAN_COMPILE=y
-CONFIG_STANDALONE=y
 CONFIG_BROKEN_ON_SMP=y

 #
 # General setup
 #
-CONFIG_SWAP=y
+CONFIG_LOCALVERSION=""
+# CONFIG_SWAP is not set
 # CONFIG_SYSVIPC is not set
 # CONFIG_POSIX_MQUEUE is not set
 # CONFIG_BSD_PROCESS_ACCT is not set
@@ -24,16 +29,19 @@ CONFIG_SYSCTL=y
 # CONFIG_AUDIT is not set
 CONFIG_LOG_BUF_SHIFT=14
 # CONFIG_HOTPLUG is not set
+CONFIG_KOBJECT_UEVENT=y
 # CONFIG_IKCONFIG is not set
 CONFIG_EMBEDDED=y
 # CONFIG_KALLSYMS is not set
 CONFIG_FUTEX=y
 CONFIG_EPOLL=y
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_CC_ALIGN_FUNCTIONS=0
+CONFIG_CC_ALIGN_LABELS=0
+CONFIG_CC_ALIGN_LOOPS=0
+CONFIG_CC_ALIGN_JUMPS=0
+# CONFIG_TINY_SHMEM is not set

 #
 # Loadable module support
@@ -45,23 +53,28 @@ CONFIG_IOSCHED_CFQ=y
 #
 CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
+CONFIG_GENERIC_HARDIRQS=y
+# CONFIG_SMP is not set
 CONFIG_ETRAX_CMDLINE="root=/dev/mtdblock3 init=/linuxrc"
-CONFIG_ETRAX_WATCHDOG=y
-CONFIG_ETRAX_WATCHDOG_NICE_DOGGY=y
+# CONFIG_ETRAX_WATCHDOG is not set
 CONFIG_ETRAX_FAST_TIMER=y
 # CONFIG_PREEMPT is not set
+# CONFIG_OOM_REBOOT is not set

 #
 # Hardware setup
 #
-CONFIG_ETRAX100LX=y
-# CONFIG_ETRAX100LX_V2 is not set
+# CONFIG_ETRAX100LX is not set
+CONFIG_ETRAX100LX_V2=y
 # CONFIG_SVINTO_SIM is not set
+# CONFIG_ETRAXFS is not set
+# CONFIG_ETRAXFS_SIM is not set
 CONFIG_ETRAX_ARCH_V10=y
-CONFIG_ETRAX_DRAM_SIZE=16
+# CONFIG_ETRAX_ARCH_V32 is not set
+CONFIG_ETRAX_DRAM_SIZE=32
 CONFIG_ETRAX_FLASH_BUSWIDTH=2
-CONFIG_CRIS_LOW_MAP=y
-CONFIG_ETRAX_DRAM_VIRTUAL_BASE=60000000
+CONFIG_ETRAX_FLASH1_SIZE=4
+CONFIG_ETRAX_DRAM_VIRTUAL_BASE=c0000000
 CONFIG_ETRAX_PA_LEDS=y
 # CONFIG_ETRAX_PB_LEDS is not set
 # CONFIG_ETRAX_CSP0_LEDS is not set
@@ -81,13 +94,13 @@ CONFIG_ETRAX_RESCUE_SER0=y
 # CONFIG_ETRAX_RESCUE_SER1 is not set
 # CONFIG_ETRAX_RESCUE_SER2 is not set
 # CONFIG_ETRAX_RESCUE_SER3 is not set
-CONFIG_ETRAX_DEF_R_WAITSTATES=0x95f8
-CONFIG_ETRAX_DEF_R_BUS_CONFIG=0x104
+CONFIG_ETRAX_DEF_R_WAITSTATES=0x95a6
+CONFIG_ETRAX_DEF_R_BUS_CONFIG=0x4
 CONFIG_ETRAX_SDRAM=y
-CONFIG_ETRAX_DEF_R_SDRAM_CONFIG=0x00e03636
+CONFIG_ETRAX_DEF_R_SDRAM_CONFIG=0x09e05757
 CONFIG_ETRAX_DEF_R_SDRAM_TIMING=0x80008002
 CONFIG_ETRAX_DEF_R_PORT_PA_DIR=0x1d
-CONFIG_ETRAX_DEF_R_PORT_PA_DATA=0xf0
+CONFIG_ETRAX_DEF_R_PORT_PA_DATA=0x00
 CONFIG_ETRAX_DEF_R_PORT_PB_CONFIG=0x00
 CONFIG_ETRAX_DEF_R_PORT_PB_DIR=0x1e
 CONFIG_ETRAX_DEF_R_PORT_PB_DATA=0xf3
@@ -97,16 +110,17 @@ CONFIG_ETRAX_DEF_R_PORT_PB_DATA=0xf3
 # Drivers for built-in interfaces
 #
 CONFIG_ETRAX_ETHERNET=y
-CONFIG_NET_ETHERNET=y
 # CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK is not set
 CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY=y
 CONFIG_ETRAX_SERIAL=y
-CONFIG_ETRAX_SERIAL_FAST_TIMER=y
+# CONFIG_ETRAX_SERIAL_FAST_TIMER is not set
+# CONFIG_ETRAX_SERIAL_FLUSH_DMA_FAST is not set
+CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS=5
 CONFIG_ETRAX_SERIAL_PORT0=y
-# CONFIG_CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_OUT is not set
-CONFIG_CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT=y
-# CONFIG_CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_IN is not set
-CONFIG_CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN=y
+# CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_OUT is not set
+CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT=y
+# CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_IN is not set
+CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN=y
 CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_ON_NONE=y
 # CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_ON_PA is not set
 # CONFIG_ETRAX_SER0_DTR_RI_DSR_CD_ON_PB is not set
@@ -121,10 +135,10 @@ CONFIG_ETRAX_SER0_DSR_ON_PB_BIT=-1
 CONFIG_ETRAX_SER0_CD_ON_PB_BIT=-1
 # CONFIG_ETRAX_SERIAL_PORT1 is not set
 CONFIG_ETRAX_SERIAL_PORT2=y
-# CONFIG_CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_OUT is not set
-CONFIG_CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT=y
-# CONFIG_CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_IN is not set
-CONFIG_CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN=y
+# CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_OUT is not set
+CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT=y
+# CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_IN is not set
+CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN=y
 CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_ON_NONE=y
 # CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_ON_PA is not set
 # CONFIG_ETRAX_SER2_DTR_RI_DSR_CD_ON_PB is not set
@@ -138,44 +152,51 @@ CONFIG_ETRAX_SER2_RI_ON_PB_BIT=-1
 CONFIG_ETRAX_SER2_DSR_ON_PB_BIT=-1
 CONFIG_ETRAX_SER2_CD_ON_PB_BIT=-1
 # CONFIG_ETRAX_SERIAL_PORT3 is not set
-# CONFIG_ETRAX_RS485 is not set
-# CONFIG_ETRAX_IDE is not set
-# CONFIG_IDE is not set
-# CONFIG_ETRAX_USB_HOST is not set
+CONFIG_ETRAX_RS485=y
+# CONFIG_ETRAX_RS485_ON_PA is not set
+# CONFIG_ETRAX_RS485_DISABLE_RECEIVER is not set
+CONFIG_ETRAX_IDE=y
+CONFIG_ETRAX_IDE_DELAY=15
+CONFIG_ETRAX_IDE_PB7_RESET=y
+# CONFIG_ETRAX_IDE_G27_RESET is not set
+CONFIG_ETRAX_USB_HOST=y
+CONFIG_ETRAX_USB_HOST_PORT1=y
+CONFIG_ETRAX_USB_HOST_PORT2=y
 CONFIG_ETRAX_AXISFLASHMAP=y
 CONFIG_ETRAX_PTABLE_SECTOR=65536
-CONFIG_MTD=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_OBSOLETE_CHIPS=y
-CONFIG_MTD_AMDSTD=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CONCAT=y
 # CONFIG_ETRAX_I2C is not set
-CONFIG_ETRAX_GPIO=y
-CONFIG_ETRAX_PA_BUTTON_BITMASK=0x02
-CONFIG_ETRAX_PA_CHANGEABLE_DIR=0x00
-CONFIG_ETRAX_PA_CHANGEABLE_BITS=0xFF
-CONFIG_ETRAX_PB_CHANGEABLE_DIR=0x00
-CONFIG_ETRAX_PB_CHANGEABLE_BITS=0xFF
-# CONFIG_ETRAX_RTC is not set
+# CONFIG_ETRAX_GPIO is not set
+CONFIG_ETRAX_RTC=y
+CONFIG_ETRAX_DS1302=y
+# CONFIG_ETRAX_PCF8563 is not set
+CONFIG_ETRAX_DS1302_RST_ON_GENERIC_PORT=y
+CONFIG_ETRAX_DS1302_RSTBIT=0
+CONFIG_ETRAX_DS1302_SCLBIT=1
+CONFIG_ETRAX_DS1302_SDABIT=0
+CONFIG_ETRAX_DS1302_TRICKLE_CHARGE=0

 #
 # Generic Driver Options
 #
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_FW_LOADER is not set

 #
 # Memory Technology Devices (MTD)
 #
+CONFIG_MTD=y
 # CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_PARTITIONS=y
+CONFIG_MTD_CONCAT=y
 # CONFIG_MTD_REDBOOT_PARTS is not set
 # CONFIG_MTD_CMDLINE_PARTS is not set

 #
 # User Modules And Translation Layers
 #
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
 # CONFIG_FTL is not set
 # CONFIG_NFTL is not set
 # CONFIG_INFTL is not set
@@ -183,14 +204,30 @@ CONFIG_ETRAX_PB_CHANGEABLE_BITS=0xFF
 #
 # RAM/ROM/Flash chip drivers
 #
+CONFIG_MTD_CFI=y
 # CONFIG_MTD_JEDECPROBE is not set
 CONFIG_MTD_GEN_PROBE=y
 # CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
 # CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_AMDSTD_RETRY=0
 # CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
 CONFIG_MTD_RAM=y
 # CONFIG_MTD_ROM is not set
 # CONFIG_MTD_ABSENT is not set
+CONFIG_MTD_OBSOLETE_CHIPS=y
+CONFIG_MTD_AMDSTD=y
 # CONFIG_MTD_SHARP is not set
 # CONFIG_MTD_JEDEC is not set

@@ -204,11 +241,13 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
 # Self-contained MTD device drivers
 #
 # CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
 CONFIG_MTD_MTDRAM=y
 CONFIG_MTDRAM_TOTAL_SIZE=0
 CONFIG_MTDRAM_ERASE_SIZE=64
 CONFIG_MTDRAM_ABS_POS=0x0
 # CONFIG_MTD_BLKMTD is not set
+# CONFIG_MTD_BLOCK2MTD is not set

 #
 # Disk-On-Chip Device Drivers
@@ -235,11 +274,25 @@ CONFIG_MTDRAM_ABS_POS=0x0
 # Block devices
 #
 # CONFIG_BLK_DEV_FD is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
 # CONFIG_BLK_DEV_LOOP is not set
 # CONFIG_BLK_DEV_NBD is not set
+# CONFIG_BLK_DEV_UB is not set
 CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
 CONFIG_BLK_DEV_RAM_SIZE=4096
 # CONFIG_BLK_DEV_INITRD is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CDROM_PKTCDVD is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+# CONFIG_IOSCHED_AS is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_ATA_OVER_ETH is not set

 #
 # Multi-device support (RAID and LVM)
@@ -249,6 +302,28 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
 #
 # ATA/ATAPI/MFM/RLL support
 #
+CONFIG_IDE=y
+CONFIG_BLK_DEV_IDE=y
+
+#
+# Please see Documentation/ide.txt for help/info on IDE drives
+#
+# CONFIG_BLK_DEV_IDE_SATA is not set
+CONFIG_BLK_DEV_IDEDISK=y
+# CONFIG_IDEDISK_MULTI_MODE is not set
+CONFIG_BLK_DEV_IDECD=y
+# CONFIG_BLK_DEV_IDETAPE is not set
+# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_IDE_TASK_IOCTL is not set
+
+#
+# IDE chipset support/bugfixes
+#
+# CONFIG_IDE_GENERIC is not set
+# CONFIG_IDE_ARM is not set
+CONFIG_BLK_DEV_IDEDMA=y
+# CONFIG_IDEDMA_AUTO is not set
+# CONFIG_BLK_DEV_HD is not set

 #
 # SCSI device support
@@ -258,7 +333,6 @@ CONFIG_BLK_DEV_RAM_SIZE=4096
 #
 # IEEE 1394 (FireWire) support
 #
-# CONFIG_IEEE1394 is not set

 #
 # I2O device support
@@ -288,6 +362,9 @@ CONFIG_INET=y
 # CONFIG_INET_AH is not set
 # CONFIG_INET_ESP is not set
 # CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_IP_TCPDIAG=y
+# CONFIG_IP_TCPDIAG_IPV6 is not set

 #
 # IP: Virtual Server Configuration
@@ -301,11 +378,10 @@ CONFIG_NETFILTER=y
 # IP: Netfilter Configuration
 #
 # CONFIG_IP_NF_CONNTRACK is not set
+# CONFIG_IP_NF_CONNTRACK_MARK is not set
 # CONFIG_IP_NF_QUEUE is not set
 # CONFIG_IP_NF_IPTABLES is not set
 # CONFIG_IP_NF_ARPTABLES is not set
-# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
-# CONFIG_IP_NF_COMPAT_IPFWADM is not set

 #
 # SCTP Configuration (EXPERIMENTAL)
@@ -323,12 +399,12 @@ CONFIG_NETFILTER=y
 # CONFIG_NET_DIVERT is not set
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_HW_FLOWCONTROL is not set

 #
 # QoS and/or fair queueing
 #
 # CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS_ROUTE is not set

 #
 # Network testing
@@ -338,7 +414,26 @@ CONFIG_NETFILTER=y
 # CONFIG_NET_POLL_CONTROLLER is not set
 # CONFIG_HAMRADIO is not set
 # CONFIG_IRDA is not set
-# CONFIG_BT is not set
+CONFIG_BT=y
+CONFIG_BT_L2CAP=y
+# CONFIG_BT_SCO is not set
+CONFIG_BT_RFCOMM=y
+# CONFIG_BT_RFCOMM_TTY is not set
+CONFIG_BT_BNEP=y
+# CONFIG_BT_BNEP_MC_FILTER is not set
+# CONFIG_BT_BNEP_PROTO_FILTER is not set
+# CONFIG_BT_HIDP is not set
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIUSB=y
+# CONFIG_BT_HCIUSB_SCO is not set
+# CONFIG_BT_HCIUART is not set
+# CONFIG_BT_HCIBCM203X is not set
+# CONFIG_BT_HCIBPA10X is not set
+# CONFIG_BT_HCIBFUSB is not set
+# CONFIG_BT_HCIVHCI is not set
 CONFIG_NETDEVICES=y
 # CONFIG_DUMMY is not set
 # CONFIG_BONDING is not set
@@ -348,6 +443,7 @@ CONFIG_NETDEVICES=y
 #
 # Ethernet (10 or 100Mbit)
 #
+CONFIG_NET_ETHERNET=y
 # CONFIG_MII is not set

 #
@@ -389,11 +485,19 @@ CONFIG_NETDEVICES=y
 #
 # Input device support
 #
-# CONFIG_INPUT is not set
+CONFIG_INPUT=y

 #
 # Userland interfaces
 #
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+# CONFIG_INPUT_TSDEV is not set
+# CONFIG_INPUT_EVDEV is not set
+# CONFIG_INPUT_EVBUG is not set

 #
 # Input I/O drivers
@@ -404,10 +508,25 @@ CONFIG_SERIO=y
 # CONFIG_SERIO_I8042 is not set
 # CONFIG_SERIO_SERPORT is not set
 # CONFIG_SERIO_CT82C710 is not set
+CONFIG_SERIO_LIBPS2=y
+# CONFIG_SERIO_RAW is not set

 #
 # Input Device Drivers
 #
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_ATKBD=y
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TOUCHSCREEN is not set
+# CONFIG_INPUT_MISC is not set

 #
 # Character devices
@@ -426,7 +545,6 @@ CONFIG_SERIO=y
 CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=256
-# CONFIG_QIC02_TAPE is not set

 #
 # IPMI
@@ -441,13 +559,10 @@ CONFIG_LEGACY_PTY_COUNT=256
 # CONFIG_GEN_RTC is not set
 # CONFIG_DTLK is not set
 # CONFIG_R3964 is not set
-# CONFIG_APPLICOM is not set

 #
 # Ftape, the floppy tape device driver
 #
-# CONFIG_FTAPE is not set
-# CONFIG_AGP is not set
 # CONFIG_DRM is not set
 # CONFIG_RAW_DRIVER is not set

@@ -469,10 +584,15 @@ CONFIG_LEGACY_PTY_COUNT=256
 # CONFIG_JBD is not set
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
+
+#
+# XFS support
+#
 # CONFIG_XFS_FS is not set
 # CONFIG_MINIX_FS is not set
 # CONFIG_ROMFS_FS is not set
 # CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
 # CONFIG_AUTOFS_FS is not set
 # CONFIG_AUTOFS4_FS is not set

@@ -485,7 +605,8 @@ CONFIG_LEGACY_PTY_COUNT=256
 #
 # DOS/FAT/NT Filesystems
 #
-# CONFIG_FAT_FS is not set
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
 # CONFIG_NTFS_FS is not set

 #
@@ -497,6 +618,7 @@ CONFIG_SYSFS=y
 # CONFIG_DEVFS_FS is not set
 # CONFIG_DEVPTS_FS_XATTR is not set
 CONFIG_TMPFS=y
+# CONFIG_TMPFS_XATTR is not set
 # CONFIG_HUGETLB_PAGE is not set
 CONFIG_RAMFS=y

@@ -512,7 +634,15 @@ CONFIG_RAMFS=y
 # CONFIG_EFS_FS is not set
 CONFIG_JFFS_FS=y
 CONFIG_JFFS_FS_VERBOSE=0
-# CONFIG_JFFS2_FS is not set
+# CONFIG_JFFS_PROC_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+# CONFIG_JFFS2_FS_NAND is not set
+# CONFIG_JFFS2_FS_NOR_ECC is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
 CONFIG_CRAMFS=y
 # CONFIG_VXFS_FS is not set
 # CONFIG_HPFS_FS is not set
@@ -530,14 +660,13 @@ CONFIG_NFS_V3=y
 # CONFIG_NFSD is not set
 CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
-# CONFIG_EXPORTFS is not set
 CONFIG_SUNRPC=y
 # CONFIG_RPCSEC_GSS_KRB5 is not set
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
 # CONFIG_SMB_FS is not set
 # CONFIG_CIFS is not set
 # CONFIG_NCP_FS is not set
 # CONFIG_CODA_FS is not set
-# CONFIG_INTERMEZZO_FS is not set
 # CONFIG_AFS_FS is not set

 #
@@ -556,9 +685,121 @@ CONFIG_MSDOS_PARTITION=y
 #
 # CONFIG_SOUND is not set

+#
+# PCCARD (PCMCIA/CardBus) support
+#
+# CONFIG_PCCARD is not set
+
+#
+# PC-card bridges
+#
+
 #
 # USB support
 #
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_BANDWIDTH is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_ARCH_HAS_HCD is not set
+# CONFIG_USB_ARCH_HAS_OHCI is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_SL811_HCD is not set
+
+#
+# USB Device Class drivers
+#
+
+#
+# USB Bluetooth TTY can only be used with disabled Bluetooth subsystem
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
+
+#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' may also be needed; see USB_STORAGE Help for more information
+#
+# CONFIG_USB_STORAGE is not set
+
+#
+# USB Input Devices
+#
+# CONFIG_USB_HID is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
+# CONFIG_USB_AIPTEK is not set
+# CONFIG_USB_WACOM is not set
+# CONFIG_USB_KBTAB is not set
+# CONFIG_USB_POWERMATE is not set
+# CONFIG_USB_MTOUCH is not set
+# CONFIG_USB_EGALAX is not set
+# CONFIG_USB_XPAD is not set
+# CONFIG_USB_ATI_REMOTE is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+
+#
+# USB Multimedia devices
+#
+# CONFIG_USB_DABUSB is not set
+
+#
+# Video4Linux support is needed for USB Multimedia device support
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+CONFIG_USB_RTL8150=y
+# CONFIG_USB_USBNET is not set
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGETKIT is not set
+# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB ATM/DSL drivers
+#

 #
 # USB Gadget Support
@@ -568,14 +809,17 @@ CONFIG_MSDOS_PARTITION=y
 #
 # Kernel hacking
 #
-# CONFIG_PROFILE is not set
+# CONFIG_PROFILING is not set
+# CONFIG_SYSTEM_PROFILER is not set
 # CONFIG_ETRAX_KGDB is not set
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_FRAME_POINTER is not set
+# CONFIG_DEBUG_NMI_OOPS is not set

 #
 # Security options
 #
+# CONFIG_KEYS is not set
 # CONFIG_SECURITY is not set

 #
@@ -583,9 +827,15 @@ CONFIG_MSDOS_PARTITION=y
 #
 # CONFIG_CRYPTO is not set

+#
+# Hardware crypto devices
+#
+
 #
 # Library routines
 #
-# CONFIG_CRC32 is not set
+# CONFIG_CRC_CCITT is not set
+CONFIG_CRC32=y
 # CONFIG_LIBCRC32C is not set
 CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
--- a/arch/cris/kernel/Makefile
+++ b/arch/cris/kernel/Makefile
-# $Id: Makefile,v 1.10 2004/05/14 10:18:12 starvik Exp $
+# $Id: Makefile,v 1.12 2004/10/19 13:07:43 starvik Exp $
 #
 # Makefile for the linux kernel.
 #
@@ -10,6 +10,7 @@ obj-y   := process.o traps.o irq.o ptrace.o setup.o \

 obj-$(CONFIG_MODULES)    += crisksyms.o
 obj-$(CONFIG_MODULES)	 += module.o
+obj-$(CONFIG_SYSTEM_PROFILER)   += profile.o

 clean: