提交 3d3fb74a 编写于 作者: R Roger Chen 提交者: David S. Miller

ARM: dts: rockchip: add gmac info for rk3288

add gmac info in rk3288.dtsi for GMAC driver

changes since v2:
1. add drive-strength in the pinctrl settings
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 7f186025
......@@ -380,6 +380,22 @@
status = "disabled";
};
gmac: ethernet@ff290000 {
compatible = "rockchip,rk3288-gmac";
reg = <0xff290000 0x10000>;
interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "macirq";
rockchip,grf = <&grf>;
clocks = <&cru SCLK_MAC>,
<&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>,
<&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>,
<&cru ACLK_GMAC>, <&cru PCLK_GMAC>;
clock-names = "stmmaceth",
"mac_clk_rx", "mac_clk_tx",
"clk_mac_ref", "clk_mac_refout",
"aclk_mac", "pclk_mac";
};
usb_host0_ehci: usb@ff500000 {
compatible = "generic-ehci";
reg = <0xff500000 0x100>;
......@@ -725,6 +741,11 @@
bias-disable;
};
pcfg_pull_none_12ma: pcfg-pull-none-12ma {
bias-disable;
drive-strength = <12>;
};
i2c0 {
i2c0_xfer: i2c0-xfer {
rockchip,pins = <0 15 RK_FUNC_1 &pcfg_pull_none>,
......@@ -1068,5 +1089,38 @@
rockchip,pins = <7 23 3 &pcfg_pull_none>;
};
};
gmac {
rgmii_pins: rgmii-pins {
rockchip,pins = <3 30 3 &pcfg_pull_none>,
<3 31 3 &pcfg_pull_none>,
<3 26 3 &pcfg_pull_none>,
<3 27 3 &pcfg_pull_none>,
<3 28 3 &pcfg_pull_none_12ma>,
<3 29 3 &pcfg_pull_none_12ma>,
<3 24 3 &pcfg_pull_none_12ma>,
<3 25 3 &pcfg_pull_none_12ma>,
<4 0 3 &pcfg_pull_none>,
<4 5 3 &pcfg_pull_none>,
<4 6 3 &pcfg_pull_none>,
<4 9 3 &pcfg_pull_none_12ma>,
<4 4 3 &pcfg_pull_none_12ma>,
<4 1 3 &pcfg_pull_none>,
<4 3 3 &pcfg_pull_none>;
};
rmii_pins: rmii-pins {
rockchip,pins = <3 30 3 &pcfg_pull_none>,
<3 31 3 &pcfg_pull_none>,
<3 28 3 &pcfg_pull_none>,
<3 29 3 &pcfg_pull_none>,
<4 0 3 &pcfg_pull_none>,
<4 5 3 &pcfg_pull_none>,
<4 4 3 &pcfg_pull_none>,
<4 1 3 &pcfg_pull_none>,
<4 2 3 &pcfg_pull_none>,
<4 3 3 &pcfg_pull_none>;
};
};
};
};
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册