Merge branch 'davem-next' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6

Documentation/networking/dm9000.txt

+DM9000 Network driver
+=====================
+
+Copyright 2008 Simtec Electronics,
+	  Ben Dooks <ben@simtec.co.uk> <ben-linux@fluff.org>
+
+
+Introduction
+------------
+
+This file describes how to use the DM9000 platform-device based network driver
+that is contained in the files drivers/net/dm9000.c and drivers/net/dm9000.h.
+
+The driver supports three DM9000 variants, the DM9000E which is the first chip
+supported as well as the newer DM9000A and DM9000B devices. It is currently
+maintained and tested by Ben Dooks, who should be CC: to any patches for this
+driver.
+
+
+Defining the platform device
+----------------------------
+
+The minimum set of resources attached to the platform device are as follows:
+
+    1) The physical address of the address register
+    2) The physical address of the data register
+    3) The IRQ line the device's interrupt pin is connected to.
+
+These resources should be specified in that order, as the ordering of the
+two address regions is important (the driver expects these to be address
+and then data).
+
+An example from arch/arm/mach-s3c2410/mach-bast.c is:
+
+static struct resource bast_dm9k_resource[] = {
+	[0] = {
+		.start = S3C2410_CS5 + BAST_PA_DM9000,
+		.end   = S3C2410_CS5 + BAST_PA_DM9000 + 3,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = S3C2410_CS5 + BAST_PA_DM9000 + 0x40,
+		.end   = S3C2410_CS5 + BAST_PA_DM9000 + 0x40 + 0x3f,
+		.flags = IORESOURCE_MEM,
+	},
+	[2] = {
+		.start = IRQ_DM9000,
+		.end   = IRQ_DM9000,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	}
+};
+
+static struct platform_device bast_device_dm9k = {
+	.name		= "dm9000",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(bast_dm9k_resource),
+	.resource	= bast_dm9k_resource,
+};
+
+Note the setting of the IRQ trigger flag in bast_dm9k_resource[2].flags,
+as this will generate a warning if it is not present. The trigger from
+the flags field will be passed to request_irq() when registering the IRQ
+handler to ensure that the IRQ is setup correctly.
+
+This shows a typical platform device, without the optional configuration
+platform data supplied. The next example uses the same resources, but adds
+the optional platform data to pass extra configuration data:
+
+static struct dm9000_plat_data bast_dm9k_platdata = {
+	.flags		= DM9000_PLATF_16BITONLY,
+};
+
+static struct platform_device bast_device_dm9k = {
+	.name		= "dm9000",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(bast_dm9k_resource),
+	.resource	= bast_dm9k_resource,
+	.dev		= {
+		.platform_data = &bast_dm9k_platdata,
+	}
+};
+
+The platform data is defined in include/linux/dm9000.h and described below.
+
+
+Platform data
+-------------
+
+Extra platform data for the DM9000 can describe the IO bus width to the
+device, whether or not an external PHY is attached to the device and
+the availability of an external configuration EEPROM.
+
+The flags for the platform data .flags field are as follows:
+
+DM9000_PLATF_8BITONLY
+
+	The IO should be done with 8bit operations.
+
+DM9000_PLATF_16BITONLY
+
+	The IO should be done with 16bit operations.
+
+DM9000_PLATF_32BITONLY
+
+	The IO should be done with 32bit operations.
+
+DM9000_PLATF_EXT_PHY
+
+	The chip is connected to an external PHY.
+
+DM9000_PLATF_NO_EEPROM
+
+	This can be used to signify that the board does not have an
+	EEPROM, or that the EEPROM should be hidden from the user.
+
+DM9000_PLATF_SIMPLE_PHY
+
+	Switch to using the simpler PHY polling method which does not
+	try and read the MII PHY state regularly. This is only available
+	when using the internal PHY. See the section on link state polling
+	for more information.
+
+	The config symbol DM9000_FORCE_SIMPLE_PHY_POLL, Kconfig entry
+	"Force simple NSR based PHY polling" allows this flag to be
+	forced on at build time.
+
+
+PHY Link state polling
+----------------------
+
+The driver keeps track of the link state and informs the network core
+about link (carrier) availablilty. This is managed by several methods
+depending on the version of the chip and on which PHY is being used.
+
+For the internal PHY, the original (and currently default) method is
+to read the MII state, either when the status changes if we have the
+necessary interrupt support in the chip or every two seconds via a
+periodic timer.
+
+To reduce the overhead for the internal PHY, there is now the option
+of using the DM9000_FORCE_SIMPLE_PHY_POLL config, or DM9000_PLATF_SIMPLE_PHY
+platform data option to read the summary information without the
+expensive MII accesses. This method is faster, but does not print
+as much information.
+
+When using an external PHY, the driver currently has to poll the MII
+link status as there is no method for getting an interrupt on link change.
+
+
+DM9000A / DM9000B
+-----------------
+
+These chips are functionally similar to the DM9000E and are supported easily
+by the same driver. The features are:
+
+   1) Interrupt on internal PHY state change. This means that the periodic
+      polling of the PHY status may be disabled on these devices when using
+      the internal PHY.
+
+   2) TCP/UDP checksum offloading, which the driver does not currently support.
+
+
+ethtool
+-------
+
+The driver supports the ethtool interface for access to the driver
+state information, the PHY state and the EEPROM.

arch/blackfin/mach-bf527/boards/ezkit.c

@@ -323,10 +323,15 @@ static struct platform_device smc91x_device = {
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
-		.end	= 0x203FB800 + 8,
+		.end	= 0x203FB800 + 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
+		.start	= 0x203FB800 + 4,
+		.end	= 0x203FB800 + 5,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
 		.start	= IRQ_PF9,
 		.end	= IRQ_PF9,
 		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),

arch/blackfin/mach-bf533/boards/H8606.c

@@ -65,10 +65,15 @@ static struct platform_device rtc_device = {
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x20300000,
-		.end	= 0x20300000 + 8,
+		.end	= 0x20300000 + 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
+		.start	= 0x20300000 + 4,
+		.end	= 0x20300000 + 5,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
 		.start	= IRQ_PF10,
 		.end	= IRQ_PF10,
 		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),

arch/blackfin/mach-bf537/boards/generic_board.c

@@ -166,10 +166,15 @@ static struct platform_device smc91x_device = {
 static struct resource dm9000_resources[] = {
 	[0] = {
 		.start	= 0x203FB800,
-		.end	= 0x203FB800 + 8,
+		.end	= 0x203FB800 + 1,
 		.flags	= IORESOURCE_MEM,
 	},
 	[1] = {
+		.start	= 0x203FB800 + 4,
+		.end	= 0x203FB800 + 5,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
 		.start	= IRQ_PF9,
 		.end	= IRQ_PF9,
 		.flags	= (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),

drivers/net/8139cp.c

@@ -1213,7 +1213,6 @@ static int cp_close (struct net_device *dev)
 
 	spin_unlock_irqrestore(&cp->lock, flags);
 
-	synchronize_irq(dev->irq);
 	free_irq(dev->irq, dev);
 
 	cp_free_rings(cp);

drivers/net/8139too.c

@@ -107,8 +107,8 @@
 #include <linux/mii.h>
 #include <linux/completion.h>
 #include <linux/crc32.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
+#include <linux/io.h>
+#include <linux/uaccess.h>
 #include <asm/irq.h>
 
 #define RTL8139_DRIVER_NAME   DRV_NAME " Fast Ethernet driver " DRV_VERSION
@@ -134,7 +134,7 @@
 
 #if RTL8139_DEBUG
 /* note: prints function name for you */
-#  define DPRINTK(fmt, args...) printk(KERN_DEBUG "%s: " fmt, __FUNCTION__ , ## args)
+#  define DPRINTK(fmt, args...) printk(KERN_DEBUG "%s: " fmt, __func__ , ## args)
 #else
 #  define DPRINTK(fmt, args...)
 #endif
@@ -145,7 +145,7 @@
 #  define assert(expr) \
         if(unlikely(!(expr))) {				        \
         printk(KERN_ERR "Assertion failed! %s,%s,%s,line=%d\n",	\
-        #expr,__FILE__,__FUNCTION__,__LINE__);		        \
+	#expr, __FILE__, __func__, __LINE__);			\
         }
 #endif
 
@@ -219,7 +219,7 @@ enum {
 #define RTL8139B_IO_SIZE 256
 
 #define RTL8129_CAPS	HAS_MII_XCVR
-#define RTL8139_CAPS	HAS_CHIP_XCVR|HAS_LNK_CHNG
+#define RTL8139_CAPS	(HAS_CHIP_XCVR|HAS_LNK_CHNG)
 
 typedef enum {
 	RTL8139 = 0,
@@ -1889,7 +1889,7 @@ static void rtl8139_rx_err (u32 rx_status, struct net_device *dev,
 }
 
 #if RX_BUF_IDX == 3
-static __inline__ void wrap_copy(struct sk_buff *skb, const unsigned char *ring,
+static inline void wrap_copy(struct sk_buff *skb, const unsigned char *ring,
 				 u32 offset, unsigned int size)
 {
 	u32 left = RX_BUF_LEN - offset;
@@ -2231,7 +2231,6 @@ static int rtl8139_close (struct net_device *dev)
 
 	spin_unlock_irqrestore (&tp->lock, flags);
 
-	synchronize_irq (dev->irq);	/* racy, but that's ok here */
 	free_irq (dev->irq, dev);
 
 	rtl8139_tx_clear (tp);

drivers/net/Kconfig

@@ -938,6 +938,23 @@ config DM9000
 	  To compile this driver as a module, choose M here.  The module
 	  will be called dm9000.
 
+config DM9000_DEBUGLEVEL
+	int "DM9000 maximum debug level"
+	depends on DM9000
+	default 4
+	help
+	  The maximum level of debugging code compiled into the DM9000
+	  driver.
+
+config DM9000_FORCE_SIMPLE_PHY_POLL
+	bool "Force simple NSR based PHY polling"
+	depends on DM9000
+	---help---
+	  This configuration forces the DM9000 to use the NSR's LinkStatus
+	  bit to determine if the link is up or down instead of the more
+	  costly MII PHY reads. Note, this will not work if the chip is
+	  operating with an external PHY.
+
 config ENC28J60
 	tristate "ENC28J60 support"
 	depends on EXPERIMENTAL && SPI && NET_ETHERNET
@@ -955,14 +972,6 @@ config ENC28J60_WRITEVERIFY
 	  Enable the verify after the buffer write useful for debugging purpose.
 	  If unsure, say N.
 
-config DM9000_DEBUGLEVEL
-	int "DM9000 maximum debug level"
-	depends on DM9000
-	default 4
-	help
-	  The maximum level of debugging code compiled into the DM9000
-	  driver.
-
 config SMC911X
 	tristate "SMSC LAN911[5678] support"
 	select CRC32
@@ -2025,9 +2034,6 @@ config E1000E
 	  To compile this driver as a module, choose M here. The module
 	  will be called e1000e.
 
-config E1000E_ENABLED
-	def_bool E1000E != n
-
 config IP1000
 	tristate "IP1000 Gigabit Ethernet support"
 	depends on PCI && EXPERIMENTAL
@@ -2462,7 +2468,8 @@ config EHEA
 
 config IXGBE
 	tristate "Intel(R) 10GbE PCI Express adapters support"
-	depends on PCI
+	depends on PCI && INET
+	select INET_LRO
 	---help---
 	  This driver supports Intel(R) 10GbE PCI Express family of
 	  adapters.  For more information on how to identify your adapter, go

drivers/net/cxgb3/cxgb3_offload.c

@@ -1248,6 +1248,25 @@ static inline void unregister_tdev(struct t3cdev *tdev)
 	mutex_unlock(&cxgb3_db_lock);
 }
 
+static inline int adap2type(struct adapter *adapter)
+{
+	int type = 0;
+
+	switch (adapter->params.rev) {
+	case T3_REV_A:
+		type = T3A;
+		break;
+	case T3_REV_B:
+	case T3_REV_B2:
+		type = T3B;
+		break;
+	case T3_REV_C:
+		type = T3C;
+		break;
+	}
+	return type;
+}
+
 void __devinit cxgb3_adapter_ofld(struct adapter *adapter)
 {
 	struct t3cdev *tdev = &adapter->tdev;
@@ -1257,7 +1276,7 @@ void __devinit cxgb3_adapter_ofld(struct adapter *adapter)
 	cxgb3_set_dummy_ops(tdev);
 	tdev->send = t3_offload_tx;
 	tdev->ctl = cxgb_offload_ctl;
-	tdev->type = adapter->params.rev == 0 ? T3A : T3B;
+	tdev->type = adap2type(adapter);
 
 	register_tdev(tdev);
 }

drivers/net/cxgb3/t3cdev.h

@@ -45,7 +45,8 @@ struct cxgb3_client;
 
 enum t3ctype {
 	T3A = 0,
-	T3B
+	T3B,
+	T3C,
 };
 
 struct t3cdev {

drivers/net/dl2k.c

@@ -1753,7 +1753,7 @@ rio_close (struct net_device *dev)
 
 	/* Stop Tx and Rx logics */
 	writel (TxDisable | RxDisable | StatsDisable, ioaddr + MACCtrl);
-	synchronize_irq (dev->irq);
+
 	free_irq (dev->irq, dev);
 	del_timer_sync (&np->timer);
 

drivers/net/dm9000.h

@@ -45,6 +45,9 @@
 #define DM9000_CHIPR           0x2C
 #define DM9000_SMCR            0x2F
 
+#define CHIPR_DM9000A	       0x19
+#define CHIPR_DM9000B	       0x1B
+
 #define DM9000_MRCMDX          0xF0
 #define DM9000_MRCMD           0xF2
 #define DM9000_MRRL            0xF4
@@ -131,5 +134,13 @@
 #define DM9000_PKT_RDY		0x01	/* Packet ready to receive */
 #define DM9000_PKT_MAX		1536	/* Received packet max size */
 
+/* DM9000A / DM9000B definitions */
+
+#define IMR_LNKCHNG		(1<<5)
+#define IMR_UNDERRUN		(1<<4)
+
+#define ISR_LNKCHNG		(1<<5)
+#define ISR_UNDERRUN		(1<<4)
+
 #endif /* _DM9000X_H_ */
 

drivers/net/e1000/e1000_main.c

@@ -47,12 +47,6 @@ static const char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation
  * Macro expands to...
  *   {PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
  */
-#ifdef CONFIG_E1000E_ENABLED
-  #define PCIE(x) 
-#else
-  #define PCIE(x) x,
-#endif
-
 static struct pci_device_id e1000_pci_tbl[] = {
 	INTEL_E1000_ETHERNET_DEVICE(0x1000),
 	INTEL_E1000_ETHERNET_DEVICE(0x1001),
@@ -79,14 +73,6 @@ static struct pci_device_id e1000_pci_tbl[] = {
 	INTEL_E1000_ETHERNET_DEVICE(0x1026),
 	INTEL_E1000_ETHERNET_DEVICE(0x1027),
 	INTEL_E1000_ETHERNET_DEVICE(0x1028),
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x1049))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x104A))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x104B))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x104C))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x104D))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x105E))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x105F))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x1060))
 	INTEL_E1000_ETHERNET_DEVICE(0x1075),
 	INTEL_E1000_ETHERNET_DEVICE(0x1076),
 	INTEL_E1000_ETHERNET_DEVICE(0x1077),
@@ -95,28 +81,9 @@ PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x1060))
 	INTEL_E1000_ETHERNET_DEVICE(0x107A),
 	INTEL_E1000_ETHERNET_DEVICE(0x107B),
 	INTEL_E1000_ETHERNET_DEVICE(0x107C),
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x107D))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x107E))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x107F))
 	INTEL_E1000_ETHERNET_DEVICE(0x108A),
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x108B))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x108C))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x1096))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x1098))
 	INTEL_E1000_ETHERNET_DEVICE(0x1099),
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x109A))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10A4))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10A5))
 	INTEL_E1000_ETHERNET_DEVICE(0x10B5),
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10B9))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10BA))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10BB))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10BC))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10C4))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10C5))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10D5))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10D9))
-PCIE(	INTEL_E1000_ETHERNET_DEVICE(0x10DA))
 	/* required last entry */
 	{0,}
 };
@@ -5284,7 +5251,6 @@ e1000_netpoll(struct net_device *netdev)
 
 	disable_irq(adapter->pdev->irq);
 	e1000_intr(adapter->pdev->irq, netdev);
-	e1000_clean_tx_irq(adapter, adapter->tx_ring);
 #ifndef CONFIG_E1000_NAPI
 	adapter->clean_rx(adapter, adapter->rx_ring);
 #endif

drivers/net/e1000e/e1000.h

@@ -283,6 +283,10 @@ struct e1000_adapter {
 	unsigned long led_status;
 
 	unsigned int flags;
+
+	/* for ioport free */
+	int bars;
+	int need_ioport;
 };
 
 struct e1000_info {

drivers/net/e1000e/netdev.c

@@ -4003,7 +4003,11 @@ static int e1000_resume(struct pci_dev *pdev)
 	pci_set_power_state(pdev, PCI_D0);
 	pci_restore_state(pdev);
 	e1000e_disable_l1aspm(pdev);
-	err = pci_enable_device(pdev);
+
+	if (adapter->need_ioport)
+		err = pci_enable_device(pdev);
+	else
+		err = pci_enable_device_mem(pdev);
 	if (err) {
 		dev_err(&pdev->dev,
 			"Cannot enable PCI device from suspend\n");
@@ -4104,9 +4108,14 @@ static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	int err;
 
 	e1000e_disable_l1aspm(pdev);
-	if (pci_enable_device(pdev)) {
+	if (adapter->need_ioport)
+		err = pci_enable_device(pdev);
+	else
+		err = pci_enable_device_mem(pdev);
+	if (err) {
 		dev_err(&pdev->dev,
 			"Cannot re-enable PCI device after reset.\n");
 		return PCI_ERS_RESULT_DISCONNECT;
@@ -4184,6 +4193,21 @@ static void e1000_print_device_info(struct e1000_adapter *adapter)
 		  (pba_num >> 8), (pba_num & 0xff));
 }
 
+/**
+ * e1000e_is_need_ioport - determine if an adapter needs ioport resources or not
+ * @pdev: PCI device information struct
+ *
+ * Returns true if an adapters needs ioport resources
+ **/
+static int e1000e_is_need_ioport(struct pci_dev *pdev)
+{
+	switch (pdev->device) {
+	/* Currently there are no adapters that need ioport resources */
+	default:
+		return false;
+	}
+}
+
 /**
  * e1000_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -4209,9 +4233,19 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	int i, err, pci_using_dac;
 	u16 eeprom_data = 0;
 	u16 eeprom_apme_mask = E1000_EEPROM_APME;
+	int bars, need_ioport;
 
 	e1000e_disable_l1aspm(pdev);
-	err = pci_enable_device(pdev);
+
+	/* do not allocate ioport bars when not needed */
+	need_ioport = e1000e_is_need_ioport(pdev);
+	if (need_ioport) {
+		bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
+		err = pci_enable_device(pdev);
+	} else {
+		bars = pci_select_bars(pdev, IORESOURCE_MEM);
+		err = pci_enable_device_mem(pdev);
+	}
 	if (err)
 		return err;
 
@@ -4234,7 +4268,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 		}
 	}
 
-	err = pci_request_regions(pdev, e1000e_driver_name);
+	err = pci_request_selected_regions(pdev, bars, e1000e_driver_name);
 	if (err)
 		goto err_pci_reg;
 
@@ -4259,6 +4293,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 	adapter->hw.adapter = adapter;
 	adapter->hw.mac.type = ei->mac;
 	adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1;
+	adapter->bars = bars;
+	adapter->need_ioport = need_ioport;
 
 	mmio_start = pci_resource_start(pdev, 0);
 	mmio_len = pci_resource_len(pdev, 0);
@@ -4498,7 +4534,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev,
 err_ioremap:
 	free_netdev(netdev);
 err_alloc_etherdev:
-	pci_release_regions(pdev);
+	pci_release_selected_regions(pdev, bars);
 err_pci_reg:
 err_dma:
 	pci_disable_device(pdev);
@@ -4546,7 +4582,7 @@ static void __devexit e1000_remove(struct pci_dev *pdev)
 	iounmap(adapter->hw.hw_addr);
 	if (adapter->hw.flash_address)
 		iounmap(adapter->hw.flash_address);
-	pci_release_regions(pdev);
+	pci_release_selected_regions(pdev, adapter->bars);
 
 	free_netdev(netdev);
 

drivers/net/fealnx.c

@@ -90,6 +90,7 @@ static int full_duplex[MAX_UNITS] = { -1, -1, -1, -1, -1, -1, -1, -1 };
 #include <asm/processor.h>	/* Processor type for cache alignment. */
 #include <asm/io.h>
 #include <asm/uaccess.h>
+#include <asm/byteorder.h>
 
 /* These identify the driver base version and may not be removed. */
 static char version[] =
@@ -861,40 +862,20 @@ static int netdev_open(struct net_device *dev)
 	   Wait the specified 50 PCI cycles after a reset by initializing
 	   Tx and Rx queues and the address filter list.
 	   FIXME (Ueimor): optimistic for alpha + posted writes ? */
-#if defined(__powerpc__) || defined(__sparc__)
-// 89/9/1 modify,
-//   np->bcrvalue=0x04 | 0x0x38;  /* big-endian, 256 burst length */
-	np->bcrvalue = 0x04 | 0x10;	/* big-endian, tx 8 burst length */
-	np->crvalue = 0xe00;	/* rx 128 burst length */
-#elif defined(__alpha__) || defined(__x86_64__)
-// 89/9/1 modify,
-//   np->bcrvalue=0x38;           /* little-endian, 256 burst length */
-	np->bcrvalue = 0x10;	/* little-endian, 8 burst length */
-	np->crvalue = 0xe00;	/* rx 128 burst length */
-#elif defined(__i386__)
-#if defined(MODULE)
-// 89/9/1 modify,
-//   np->bcrvalue=0x38;           /* little-endian, 256 burst length */
+
 	np->bcrvalue = 0x10;	/* little-endian, 8 burst length */
-	np->crvalue = 0xe00;	/* rx 128 burst length */
-#else
-	/* When not a module we can work around broken '486 PCI boards. */
-#define x86 boot_cpu_data.x86
-// 89/9/1 modify,
-//   np->bcrvalue=(x86 <= 4 ? 0x10 : 0x38);
-	np->bcrvalue = 0x10;
-	np->crvalue = (x86 <= 4 ? 0xa00 : 0xe00);
-	if (x86 <= 4)
-		printk(KERN_INFO "%s: This is a 386/486 PCI system, setting burst "
-		       "length to %x.\n", dev->name, (x86 <= 4 ? 0x10 : 0x38));
+#ifdef __BIG_ENDIAN
+	np->bcrvalue |= 0x04;	/* big-endian */
 #endif
-#else
-// 89/9/1 modify,
-//   np->bcrvalue=0x38;
-	np->bcrvalue = 0x10;
-	np->crvalue = 0xe00;	/* rx 128 burst length */
-#warning Processor architecture undefined!
+
+#if defined(__i386__) && !defined(MODULE)
+	if (boot_cpu_data.x86 <= 4)
+		np->crvalue = 0xa00;
+	else
 #endif
+		np->crvalue = 0xe00;	/* rx 128 burst length */
+
+
 // 89/12/29 add,
 // 90/1/16 modify,
 //   np->imrvalue=FBE|TUNF|CNTOVF|RBU|TI|RI;

drivers/net/forcedeth.c

@@ -5559,6 +5559,11 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i
 	/* set mac address */
 	nv_copy_mac_to_hw(dev);
 
+	/* Workaround current PCI init glitch:  wakeup bits aren't
+	 * being set from PCI PM capability.
+	 */
+	device_init_wakeup(&pci_dev->dev, 1);
+
 	/* disable WOL */
 	writel(0, base + NvRegWakeUpFlags);
 	np->wolenabled = 0;

drivers/net/igb/igb.h

@@ -271,6 +271,10 @@ struct igb_adapter {
 	unsigned int msi_enabled;
 
 	u32 eeprom_wol;
+
+	/* for ioport free */
+	int bars;
+	int need_ioport;
 };
 
 enum e1000_state_t {

drivers/net/igb/igb_main.c

@@ -820,6 +820,21 @@ void igb_reset(struct igb_adapter *adapter)
 		adapter->hw.phy.ops.get_phy_info(&adapter->hw);
 }
 
+/**
+ * igb_is_need_ioport - determine if an adapter needs ioport resources or not
+ * @pdev: PCI device information struct
+ *
+ * Returns true if an adapter needs ioport resources
+ **/
+static int igb_is_need_ioport(struct pci_dev *pdev)
+{
+	switch (pdev->device) {
+	/* Currently there are no adapters that need ioport resources */
+	default:
+		return false;
+	}
+}
+
 /**
  * igb_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -844,8 +859,17 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 	u16 eeprom_data = 0;
 	u16 eeprom_apme_mask = IGB_EEPROM_APME;
 	u32 part_num;
+	int bars, need_ioport;
 
-	err = pci_enable_device(pdev);
+	/* do not allocate ioport bars when not needed */
+	need_ioport = igb_is_need_ioport(pdev);
+	if (need_ioport) {
+		bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
+		err = pci_enable_device(pdev);
+	} else {
+		bars = pci_select_bars(pdev, IORESOURCE_MEM);
+		err = pci_enable_device_mem(pdev);
+	}
 	if (err)
 		return err;
 
@@ -867,7 +891,7 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 		}
 	}
 
-	err = pci_request_regions(pdev, igb_driver_name);
+	err = pci_request_selected_regions(pdev, bars, igb_driver_name);
 	if (err)
 		goto err_pci_reg;
 
@@ -888,6 +912,8 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 	hw = &adapter->hw;
 	hw->back = adapter;
 	adapter->msg_enable = NETIF_MSG_DRV | NETIF_MSG_PROBE;
+	adapter->bars = bars;
+	adapter->need_ioport = need_ioport;
 
 	mmio_start = pci_resource_start(pdev, 0);
 	mmio_len = pci_resource_len(pdev, 0);
@@ -1128,7 +1154,7 @@ static int __devinit igb_probe(struct pci_dev *pdev,
 err_ioremap:
 	free_netdev(netdev);
 err_alloc_etherdev:
-	pci_release_regions(pdev);
+	pci_release_selected_regions(pdev, bars);
 err_pci_reg:
 err_dma:
 	pci_disable_device(pdev);
@@ -1175,7 +1201,7 @@ static void __devexit igb_remove(struct pci_dev *pdev)
 	iounmap(adapter->hw.hw_addr);
 	if (adapter->hw.flash_address)
 		iounmap(adapter->hw.flash_address);
-	pci_release_regions(pdev);
+	pci_release_selected_regions(pdev, adapter->bars);
 
 	free_netdev(netdev);
 
@@ -3976,7 +4002,11 @@ static int igb_resume(struct pci_dev *pdev)
 
 	pci_set_power_state(pdev, PCI_D0);
 	pci_restore_state(pdev);
-	err = pci_enable_device(pdev);
+
+	if (adapter->need_ioport)
+		err = pci_enable_device(pdev);
+	else
+		err = pci_enable_device_mem(pdev);
 	if (err) {
 		dev_err(&pdev->dev,
 			"igb: Cannot enable PCI device from suspend\n");
@@ -4079,8 +4109,13 @@ static pci_ers_result_t igb_io_slot_reset(struct pci_dev *pdev)
 	struct net_device *netdev = pci_get_drvdata(pdev);
 	struct igb_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	int err;
 
-	if (pci_enable_device(pdev)) {
+	if (adapter->need_ioport)
+		err = pci_enable_device(pdev);
+	else
+		err = pci_enable_device_mem(pdev);
+	if (err) {
 		dev_err(&pdev->dev,
 			"Cannot re-enable PCI device after reset.\n");
 		return PCI_ERS_RESULT_DISCONNECT;

drivers/net/ixgbe/ixgbe.h

@@ -32,6 +32,7 @@
 #include <linux/types.h>
 #include <linux/pci.h>
 #include <linux/netdevice.h>
+#include <linux/inet_lro.h>
 
 #include "ixgbe_type.h"
 #include "ixgbe_common.h"
@@ -100,6 +101,9 @@
 #define IXGBE_TX_FLAGS_VLAN_MASK	0xffff0000
 #define IXGBE_TX_FLAGS_VLAN_SHIFT	16
 
+#define IXGBE_MAX_LRO_DESCRIPTORS       8
+#define IXGBE_MAX_LRO_AGGREGATE         32
+
 /* wrapper around a pointer to a socket buffer,
  * so a DMA handle can be stored along with the buffer */
 struct ixgbe_tx_buffer {
@@ -150,6 +154,8 @@ struct ixgbe_ring {
 	/* cpu for tx queue */
 	int cpu;
 #endif
+	struct net_lro_mgr lro_mgr;
+	bool lro_used;
 	struct ixgbe_queue_stats stats;
 	u8 v_idx; /* maps directly to the index for this ring in the hardware
 		   * vector array, can also be used for finding the bit in EICR
@@ -287,6 +293,9 @@ struct ixgbe_adapter {
 
 	unsigned long state;
 	u64 tx_busy;
+	u64 lro_aggregated;
+	u64 lro_flushed;
+	u64 lro_no_desc;
 };
 
 enum ixbge_state_t {

drivers/net/ixgbe/ixgbe_ethtool.c

@@ -90,6 +90,8 @@ static struct ixgbe_stats ixgbe_gstrings_stats[] = {
 	{"rx_header_split", IXGBE_STAT(rx_hdr_split)},
 	{"alloc_rx_page_failed", IXGBE_STAT(alloc_rx_page_failed)},
 	{"alloc_rx_buff_failed", IXGBE_STAT(alloc_rx_buff_failed)},
+	{"lro_aggregated", IXGBE_STAT(lro_aggregated)},
+	{"lro_flushed", IXGBE_STAT(lro_flushed)},
 };
 
 #define IXGBE_QUEUE_STATS_LEN \
@@ -787,6 +789,7 @@ static void ixgbe_get_ethtool_stats(struct net_device *netdev,
 	int stat_count = sizeof(struct ixgbe_queue_stats) / sizeof(u64);
 	int j, k;
 	int i;
+	u64 aggregated = 0, flushed = 0, no_desc = 0;
 
 	ixgbe_update_stats(adapter);
 	for (i = 0; i < IXGBE_GLOBAL_STATS_LEN; i++) {
@@ -801,11 +804,17 @@ static void ixgbe_get_ethtool_stats(struct net_device *netdev,
 		i += k;
 	}
 	for (j = 0; j < adapter->num_rx_queues; j++) {
+		aggregated += adapter->rx_ring[j].lro_mgr.stats.aggregated;
+		flushed += adapter->rx_ring[j].lro_mgr.stats.flushed;
+		no_desc += adapter->rx_ring[j].lro_mgr.stats.no_desc;
 		queue_stat = (u64 *)&adapter->rx_ring[j].stats;
 		for (k = 0; k < stat_count; k++)
 			data[i + k] = queue_stat[k];
 		i += k;
 	}
+	adapter->lro_aggregated = aggregated;
+	adapter->lro_flushed = flushed;
+	adapter->lro_no_desc = no_desc;
 }
 
 static void ixgbe_get_strings(struct net_device *netdev, u32 stringset,
@@ -973,6 +982,8 @@ static struct ethtool_ops ixgbe_ethtool_ops = {
 	.get_ethtool_stats      = ixgbe_get_ethtool_stats,
 	.get_coalesce           = ixgbe_get_coalesce,
 	.set_coalesce           = ixgbe_set_coalesce,
+	.get_flags              = ethtool_op_get_flags,
+	.set_flags              = ethtool_op_set_flags,
 };
 
 void ixgbe_set_ethtool_ops(struct net_device *netdev)

drivers/net/ixgbe/ixgbe_main.c

@@ -389,24 +389,39 @@ static int __ixgbe_notify_dca(struct device *dev, void *data)
  * ixgbe_receive_skb - Send a completed packet up the stack
  * @adapter: board private structure
  * @skb: packet to send up
- * @is_vlan: packet has a VLAN tag
- * @tag: VLAN tag from descriptor
+ * @status: hardware indication of status of receive
+ * @rx_ring: rx descriptor ring (for a specific queue) to setup
+ * @rx_desc: rx descriptor
  **/
 static void ixgbe_receive_skb(struct ixgbe_adapter *adapter,
-			      struct sk_buff *skb, bool is_vlan,
-			      u16 tag)
+			      struct sk_buff *skb, u8 status,
+			      struct ixgbe_ring *ring,
+                              union ixgbe_adv_rx_desc *rx_desc)
 {
-	if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL)) {
-		if (adapter->vlgrp && is_vlan)
-			vlan_hwaccel_receive_skb(skb, adapter->vlgrp, tag);
-		else
-			netif_receive_skb(skb);
-	} else {
+	bool is_vlan = (status & IXGBE_RXD_STAT_VP);
+	u16 tag = le16_to_cpu(rx_desc->wb.upper.vlan);
 
+	if (adapter->netdev->features & NETIF_F_LRO &&
+	    skb->ip_summed == CHECKSUM_UNNECESSARY) {
 		if (adapter->vlgrp && is_vlan)
-			vlan_hwaccel_rx(skb, adapter->vlgrp, tag);
+			lro_vlan_hwaccel_receive_skb(&ring->lro_mgr, skb,
+			                             adapter->vlgrp, tag,
+			                             rx_desc);
 		else
-			netif_rx(skb);
+			lro_receive_skb(&ring->lro_mgr, skb, rx_desc);
+		ring->lro_used = true;
+	} else {
+		if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL)) {
+			if (adapter->vlgrp && is_vlan)
+				vlan_hwaccel_receive_skb(skb, adapter->vlgrp, tag);
+			else
+				netif_receive_skb(skb);
+		} else {
+			if (adapter->vlgrp && is_vlan)
+				vlan_hwaccel_rx(skb, adapter->vlgrp, tag);
+			else
+				netif_rx(skb);
+		}
 	}
 }
 
@@ -546,8 +561,8 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_adapter *adapter,
 	struct sk_buff *skb;
 	unsigned int i;
 	u32 upper_len, len, staterr;
-	u16 hdr_info, vlan_tag;
-	bool is_vlan, cleaned = false;
+	u16 hdr_info;
+	bool cleaned = false;
 	int cleaned_count = 0;
 	unsigned int total_rx_bytes = 0, total_rx_packets = 0;
 
@@ -556,8 +571,6 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_adapter *adapter,
 	rx_desc = IXGBE_RX_DESC_ADV(*rx_ring, i);
 	staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
 	rx_buffer_info = &rx_ring->rx_buffer_info[i];
-	is_vlan = (staterr & IXGBE_RXD_STAT_VP);
-	vlan_tag = le16_to_cpu(rx_desc->wb.upper.vlan);
 
 	while (staterr & IXGBE_RXD_STAT_DD) {
 		if (*work_done >= work_to_do)
@@ -635,7 +648,7 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_adapter *adapter,
 		total_rx_packets++;
 
 		skb->protocol = eth_type_trans(skb, netdev);
-		ixgbe_receive_skb(adapter, skb, is_vlan, vlan_tag);
+		ixgbe_receive_skb(adapter, skb, staterr, rx_ring, rx_desc);
 		netdev->last_rx = jiffies;
 
 next_desc:
@@ -652,8 +665,11 @@ static bool ixgbe_clean_rx_irq(struct ixgbe_adapter *adapter,
 		rx_buffer_info = next_buffer;
 
 		staterr = le32_to_cpu(rx_desc->wb.upper.status_error);
-		is_vlan = (staterr & IXGBE_RXD_STAT_VP);
-		vlan_tag = le16_to_cpu(rx_desc->wb.upper.vlan);
+	}
+
+	if (rx_ring->lro_used) {
+		lro_flush_all(&rx_ring->lro_mgr);
+		rx_ring->lro_used = false;
 	}
 
 	rx_ring->next_to_clean = i;
@@ -1381,6 +1397,33 @@ static void ixgbe_configure_tx(struct ixgbe_adapter *adapter)
 			(((S) & (PAGE_SIZE - 1)) ? 1 : 0))
 
 #define IXGBE_SRRCTL_BSIZEHDRSIZE_SHIFT			2
+/**
+ * ixgbe_get_skb_hdr - helper function for LRO header processing
+ * @skb: pointer to sk_buff to be added to LRO packet
+ * @iphdr: pointer to tcp header structure
+ * @tcph: pointer to tcp header structure
+ * @hdr_flags: pointer to header flags
+ * @priv: private data
+ **/
+static int ixgbe_get_skb_hdr(struct sk_buff *skb, void **iphdr, void **tcph,
+                             u64 *hdr_flags, void *priv)
+{
+	union ixgbe_adv_rx_desc *rx_desc = priv;
+
+	/* Verify that this is a valid IPv4 TCP packet */
+	if (!(rx_desc->wb.lower.lo_dword.pkt_info &
+	    (IXGBE_RXDADV_PKTTYPE_IPV4 | IXGBE_RXDADV_PKTTYPE_TCP)))
+		return -1;
+
+	/* Set network headers */
+	skb_reset_network_header(skb);
+	skb_set_transport_header(skb, ip_hdrlen(skb));
+	*iphdr = ip_hdr(skb);
+	*tcph = tcp_hdr(skb);
+	*hdr_flags = LRO_IPV4 | LRO_TCP;
+	return 0;
+}
+
 /**
  * ixgbe_configure_rx - Configure 8254x Receive Unit after Reset
  * @adapter: board private structure
@@ -1470,6 +1513,17 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter)
 		adapter->rx_ring[i].tail = IXGBE_RDT(i);
 	}
 
+	/* Intitial LRO Settings */
+	adapter->rx_ring[i].lro_mgr.max_aggr = IXGBE_MAX_LRO_AGGREGATE;
+	adapter->rx_ring[i].lro_mgr.max_desc = IXGBE_MAX_LRO_DESCRIPTORS;
+	adapter->rx_ring[i].lro_mgr.get_skb_header = ixgbe_get_skb_hdr;
+	adapter->rx_ring[i].lro_mgr.features = LRO_F_EXTRACT_VLAN_ID;
+	if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL))
+		adapter->rx_ring[i].lro_mgr.features |= LRO_F_NAPI;
+	adapter->rx_ring[i].lro_mgr.dev = adapter->netdev;
+	adapter->rx_ring[i].lro_mgr.ip_summed = CHECKSUM_UNNECESSARY;
+	adapter->rx_ring[i].lro_mgr.ip_summed_aggr = CHECKSUM_UNNECESSARY;
+
 	if (adapter->flags & IXGBE_FLAG_RSS_ENABLED) {
 		/* Fill out redirection table */
 		for (i = 0, j = 0; i < 128; i++, j++) {
@@ -2490,12 +2544,18 @@ int ixgbe_setup_rx_resources(struct ixgbe_adapter *adapter,
 	struct pci_dev *pdev = adapter->pdev;
 	int size;
 
+	size = sizeof(struct net_lro_desc) * IXGBE_MAX_LRO_DESCRIPTORS;
+	rxdr->lro_mgr.lro_arr = vmalloc(size);
+	if (!rxdr->lro_mgr.lro_arr)
+		return -ENOMEM;
+	memset(rxdr->lro_mgr.lro_arr, 0, size);
+
 	size = sizeof(struct ixgbe_rx_buffer) * rxdr->count;
 	rxdr->rx_buffer_info = vmalloc(size);
 	if (!rxdr->rx_buffer_info) {
 		DPRINTK(PROBE, ERR,
 			"vmalloc allocation failed for the rx desc ring\n");
-		return -ENOMEM;
+		goto alloc_failed;
 	}
 	memset(rxdr->rx_buffer_info, 0, size);
 
@@ -2509,13 +2569,18 @@ int ixgbe_setup_rx_resources(struct ixgbe_adapter *adapter,
 		DPRINTK(PROBE, ERR,
 			"Memory allocation failed for the rx desc ring\n");
 		vfree(rxdr->rx_buffer_info);
-		return -ENOMEM;
+		goto alloc_failed;
 	}
 
 	rxdr->next_to_clean = 0;
 	rxdr->next_to_use = 0;
 
 	return 0;
+
+alloc_failed:
+	vfree(rxdr->lro_mgr.lro_arr);
+	rxdr->lro_mgr.lro_arr = NULL;
+	return -ENOMEM;
 }
 
 /**
@@ -2566,6 +2631,9 @@ static void ixgbe_free_rx_resources(struct ixgbe_adapter *adapter,
 {
 	struct pci_dev *pdev = adapter->pdev;
 
+	vfree(rx_ring->lro_mgr.lro_arr);
+	rx_ring->lro_mgr.lro_arr = NULL;
+
 	ixgbe_clean_rx_ring(adapter, rx_ring);
 
 	vfree(rx_ring->rx_buffer_info);
@@ -3518,6 +3586,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
 			   NETIF_F_HW_VLAN_RX |
 			   NETIF_F_HW_VLAN_FILTER;
 
+	netdev->features |= NETIF_F_LRO;
 	netdev->features |= NETIF_F_TSO;
 	netdev->features |= NETIF_F_TSO6;
 

drivers/net/pci-skeleton.c

@@ -1739,7 +1739,6 @@ static int netdrv_close (struct net_device *dev)
 
 	spin_unlock_irqrestore (&tp->lock, flags);
 
-	synchronize_irq (dev->irq);
 	free_irq (dev->irq, dev);
 
 	netdrv_tx_clear (dev);

drivers/net/sh_eth.c

@@ -322,7 +322,7 @@ static int sh_eth_dev_init(struct net_device *ndev)
 	ctrl_outl((FIFO_SIZE_T | FIFO_SIZE_R), ioaddr + FDR);
 	ctrl_outl(0, ioaddr + TFTR);
 
-	ctrl_outl(RMCR_RST, ioaddr + RMCR);
+	ctrl_outl(0, ioaddr + RMCR);
 
 	rx_int_var = mdp->rx_int_var = DESC_I_RINT8 | DESC_I_RINT5;
 	tx_int_var = mdp->tx_int_var = DESC_I_TINT2;
@@ -994,7 +994,7 @@ static int sh_mdio_init(struct net_device *ndev, int id)
 	/* Hook up MII support for ethtool */
 	mdp->mii_bus->name = "sh_mii";
 	mdp->mii_bus->dev = &ndev->dev;
-	mdp->mii_bus->id = id;
+	mdp->mii_bus->id[0] = id;
 
 	/* PHY IRQ */
 	mdp->mii_bus->irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL);

drivers/net/sh_eth.h

@@ -40,8 +40,6 @@
 #define PKT_BUF_SZ		1538
 
 /* Chip Base Address */
-#define SH_ETH0_BASE 0xA7000000
-#define SH_ETH1_BASE 0xA7000400
 #define SH_TSU_ADDR 0xA7000804
 
 /* Chip Registers */
@@ -462,3 +460,5 @@ static void swaps(char *src, int len)
 		*p = swab32(*p);
 #endif
 }
+
+#endif

drivers/net/tsi108_eth.c

@@ -1437,7 +1437,6 @@ static int tsi108_close(struct net_device *dev)
 		dev_kfree_skb(skb);
 	}
 
-	synchronize_irq(data->irq_num);
 	free_irq(data->irq_num, dev);
 
 	/* Discard the RX ring. */

drivers/net/tulip/21142.c

 /*
 	drivers/net/tulip/21142.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,9 +8,8 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
-
+	for more information on this driver.
+	Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
 #include <linux/delay.h>

drivers/net/tulip/de2104x.c

@@ -124,8 +124,6 @@ MODULE_PARM_DESC (rx_copybreak, "de2104x Breakpoint at which Rx packets are copi
 /* Time in jiffies before concluding the transmitter is hung. */
 #define TX_TIMEOUT		(6*HZ)
 
-#define DE_UNALIGNED_16(a)	(u16)(get_unaligned((u16 *)(a)))
-
 /* This is a mysterious value that can be written to CSR11 in the 21040 (only)
    to support a pre-NWay full-duplex signaling mechanism using short frames.
    No one knows what it should be, but if left at its default value some
@@ -1811,7 +1809,7 @@ static void __devinit de21041_get_srom_info (struct de_private *de)
 		goto bad_srom;
 
 	/* get default media type */
-	switch (DE_UNALIGNED_16(&il->default_media)) {
+	switch (get_unaligned(&il->default_media)) {
 	case 0x0001:  de->media_type = DE_MEDIA_BNC; break;
 	case 0x0002:  de->media_type = DE_MEDIA_AUI; break;
 	case 0x0204:  de->media_type = DE_MEDIA_TP_FD; break;
@@ -1875,9 +1873,9 @@ static void __devinit de21041_get_srom_info (struct de_private *de)
 		bufp += sizeof (ib->opts);
 
 		if (ib->opts & MediaCustomCSRs) {
-			de->media[idx].csr13 = DE_UNALIGNED_16(&ib->csr13);
-			de->media[idx].csr14 = DE_UNALIGNED_16(&ib->csr14);
-			de->media[idx].csr15 = DE_UNALIGNED_16(&ib->csr15);
+			de->media[idx].csr13 = get_unaligned(&ib->csr13);
+			de->media[idx].csr14 = get_unaligned(&ib->csr14);
+			de->media[idx].csr15 = get_unaligned(&ib->csr15);
 			bufp += sizeof(ib->csr13) + sizeof(ib->csr14) +
 				sizeof(ib->csr15);
 

drivers/net/tulip/eeprom.c

 /*
 	drivers/net/tulip/eeprom.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,9 +8,8 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
-
+	for more information on this driver.
+	Please submit bug reports to http://bugzilla.kernel.org/.
 */
 
 #include <linux/pci.h>

drivers/net/tulip/interrupt.c

 /*
 	drivers/net/tulip/interrupt.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,8 +8,8 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
+        Please submit bugs to http://bugzilla.kernel.org/ .
 
 */
 

drivers/net/tulip/media.c

 /*
 	drivers/net/tulip/media.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,9 +8,9 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
 
+	Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
 #include <linux/kernel.h>

drivers/net/tulip/pnic.c

 /*
 	drivers/net/tulip/pnic.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,9 +8,9 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
 
+	Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
 #include <linux/kernel.h>

drivers/net/tulip/pnic2.c

 /*
 	drivers/net/tulip/pnic2.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
         Modified to hep support PNIC_II by Kevin B. Hendricks
@@ -10,9 +9,9 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
 
+        Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
 

drivers/net/tulip/timer.c

 /*
 	drivers/net/tulip/timer.c
 
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,11 +8,12 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
 
+	Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
+
 #include "tulip.h"
 
 

drivers/net/tulip/tulip.h

@@ -8,9 +8,9 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
 
+	Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
 #ifndef __NET_TULIP_H__

drivers/net/tulip/tulip_core.c

-/* tulip_core.c: A DEC 21x4x-family ethernet driver for Linux. */
+/*	tulip_core.c: A DEC 21x4x-family ethernet driver for Linux.
 
-/*
-	Maintained by Valerie Henson <val_henson@linux.intel.com>
 	Copyright 2000,2001  The Linux Kernel Team
 	Written/copyright 1994-2001 by Donald Becker.
 
@@ -9,9 +7,9 @@
 	of the GNU General Public License, incorporated herein by reference.
 
 	Please refer to Documentation/DocBook/tulip-user.{pdf,ps,html}
-	for more information on this driver, or visit the project
-	Web page at http://sourceforge.net/projects/tulip/
+	for more information on this driver.
 
+	Please submit bugs to http://bugzilla.kernel.org/ .
 */
 
 

drivers/net/typhoon.c

@@ -334,8 +334,6 @@ enum state_values {
 #define TYPHOON_RESET_TIMEOUT_NOSLEEP	((6 * 1000000) / TYPHOON_UDELAY)
 #define TYPHOON_WAIT_TIMEOUT		((1000000 / 2) / TYPHOON_UDELAY)
 
-#define typhoon_synchronize_irq(x) synchronize_irq(x)
-
 #if defined(NETIF_F_TSO)
 #define skb_tso_size(x)		(skb_shinfo(x)->gso_size)
 #define TSO_NUM_DESCRIPTORS	2
@@ -2143,7 +2141,6 @@ typhoon_close(struct net_device *dev)
 		printk(KERN_ERR "%s: unable to stop runtime\n", dev->name);
 
 	/* Make sure there is no irq handler running on a different CPU. */
-	typhoon_synchronize_irq(dev->irq);
 	free_irq(dev->irq, dev);
 
 	typhoon_free_rx_rings(tp);

drivers/net/usb/rndis_host.c

@@ -74,7 +74,7 @@ EXPORT_SYMBOL_GPL(rndis_status);
  * Call context is likely probe(), before interface name is known,
  * which is why we won't try to use it in the diagnostics.
  */
-int rndis_command(struct usbnet *dev, struct rndis_msg_hdr *buf)
+int rndis_command(struct usbnet *dev, struct rndis_msg_hdr *buf, int buflen)
 {
 	struct cdc_state	*info = (void *) &dev->data;
 	int			master_ifnum;
@@ -121,7 +121,7 @@ int rndis_command(struct usbnet *dev, struct rndis_msg_hdr *buf)
 			USB_CDC_GET_ENCAPSULATED_RESPONSE,
 			USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
 			0, master_ifnum,
-			buf, CONTROL_BUFFER_SIZE,
+			buf, buflen,
 			RNDIS_CONTROL_TIMEOUT_MS);
 		if (likely(retval >= 8)) {
 			msg_len = le32_to_cpu(buf->msg_len);
@@ -239,7 +239,7 @@ static int rndis_query(struct usbnet *dev, struct usb_interface *intf,
 	u.get->len = cpu_to_le32(in_len);
 	u.get->offset = ccpu2(20);
 
-	retval = rndis_command(dev, u.header);
+	retval = rndis_command(dev, u.header, CONTROL_BUFFER_SIZE);
 	if (unlikely(retval < 0)) {
 		dev_err(&intf->dev, "RNDIS_MSG_QUERY(0x%08x) failed, %d\n",
 				oid, retval);
@@ -328,7 +328,7 @@ generic_rndis_bind(struct usbnet *dev, struct usb_interface *intf, int flags)
 	u.init->max_transfer_size = cpu_to_le32(dev->rx_urb_size);
 
 	net->change_mtu = NULL;
-	retval = rndis_command(dev, u.header);
+	retval = rndis_command(dev, u.header, CONTROL_BUFFER_SIZE);
 	if (unlikely(retval < 0)) {
 		/* it might not even be an RNDIS device!! */
 		dev_err(&intf->dev, "RNDIS init failed, %d\n", retval);
@@ -409,7 +409,7 @@ generic_rndis_bind(struct usbnet *dev, struct usb_interface *intf, int flags)
 	u.set->offset = ccpu2((sizeof *u.set) - 8);
 	*(__le32 *)(u.buf + sizeof *u.set) = RNDIS_DEFAULT_FILTER;
 
-	retval = rndis_command(dev, u.header);
+	retval = rndis_command(dev, u.header, CONTROL_BUFFER_SIZE);
 	if (unlikely(retval < 0)) {
 		dev_err(&intf->dev, "rndis set packet filter, %d\n", retval);
 		goto halt_fail_and_release;
@@ -424,7 +424,7 @@ generic_rndis_bind(struct usbnet *dev, struct usb_interface *intf, int flags)
 	memset(u.halt, 0, sizeof *u.halt);
 	u.halt->msg_type = RNDIS_MSG_HALT;
 	u.halt->msg_len = ccpu2(sizeof *u.halt);
-	(void) rndis_command(dev, (void *)u.halt);
+	(void) rndis_command(dev, (void *)u.halt, CONTROL_BUFFER_SIZE);
 fail_and_release:
 	usb_set_intfdata(info->data, NULL);
 	usb_driver_release_interface(driver_of(intf), info->data);
@@ -449,7 +449,7 @@ void rndis_unbind(struct usbnet *dev, struct usb_interface *intf)
 	if (halt) {
 		halt->msg_type = RNDIS_MSG_HALT;
 		halt->msg_len = ccpu2(sizeof *halt);
-		(void) rndis_command(dev, (void *)halt);
+		(void) rndis_command(dev, (void *)halt, CONTROL_BUFFER_SIZE);
 		kfree(halt);
 	}
 

drivers/net/wireless/rndis_wlan.c

@@ -448,7 +448,7 @@ static int rndis_query_oid(struct usbnet *dev, __le32 oid, void *data, int *len)
 	u.get->msg_len = ccpu2(sizeof *u.get);
 	u.get->oid = oid;
 
-	ret = rndis_command(dev, u.header);
+	ret = rndis_command(dev, u.header, buflen);
 	if (ret == 0) {
 		ret = le32_to_cpu(u.get_c->len);
 		*len = (*len > ret) ? ret : *len;
@@ -498,7 +498,7 @@ static int rndis_set_oid(struct usbnet *dev, __le32 oid, void *data, int len)
 	u.set->handle = ccpu2(0);
 	memcpy(u.buf + sizeof(*u.set), data, len);
 
-	ret = rndis_command(dev, u.header);
+	ret = rndis_command(dev, u.header, buflen);
 	if (ret == 0)
 		ret = rndis_error_status(u.set_c->status);
 

drivers/pci/pci-acpi.c

@@ -315,6 +315,25 @@ static pci_power_t acpi_pci_choose_state(struct pci_dev *pdev,
 	}
 	return PCI_POWER_ERROR;
 }
+
+static int acpi_platform_enable_wakeup(struct device *dev, int is_on)
+{
+	struct acpi_device	*adev;
+	int			status;
+
+	if (!device_can_wakeup(dev))
+		return -EINVAL;
+
+	if (is_on && !device_may_wakeup(dev))
+		return -EINVAL;
+
+	status = acpi_bus_get_device(DEVICE_ACPI_HANDLE(dev), &adev);
+	if (status < 0)
+		return status;
+
+	adev->wakeup.state.enabled = !!is_on;
+	return 0;
+}
 #endif
 
 static int acpi_pci_set_power_state(struct pci_dev *dev, pci_power_t state)
@@ -399,6 +418,7 @@ static int __init acpi_pci_init(void)
 		return 0;
 #ifdef	CONFIG_ACPI_SLEEP
 	platform_pci_choose_state = acpi_pci_choose_state;
+	platform_enable_wakeup = acpi_platform_enable_wakeup;
 #endif
 	platform_pci_set_power_state = acpi_pci_set_power_state;
 	return 0;

include/linux/dm9000.h

@@ -21,6 +21,7 @@
 #define DM9000_PLATF_32BITONLY	(0x0004)
 #define DM9000_PLATF_EXT_PHY	(0x0008)
 #define DM9000_PLATF_NO_EEPROM	(0x0010)
+#define DM9000_PLATF_SIMPLE_PHY (0x0020)  /* Use NSR to find LinkStatus */
 
 /* platfrom data for platfrom device structure's platfrom_data field */
 

include/linux/usb/rndis_host.h

@@ -260,7 +260,8 @@ struct rndis_keepalive_c {	/* IN (optionally OUT) */
 
 
 extern void rndis_status(struct usbnet *dev, struct urb *urb);
-extern int rndis_command(struct usbnet *dev, struct rndis_msg_hdr *buf);
+extern int
+rndis_command(struct usbnet *dev, struct rndis_msg_hdr *buf, int buflen);
 extern int
 generic_rndis_bind(struct usbnet *dev, struct usb_interface *intf, int flags);
 extern void rndis_unbind(struct usbnet *dev, struct usb_interface *intf);