USB: Driver for Freescale QUICC Engine USB Host Controller

This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.

Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.

This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/Makefile

@@ -13,6 +13,7 @@ obj-$(CONFIG_USB_EHCI_HCD)	+= host/
 obj-$(CONFIG_USB_ISP116X_HCD)	+= host/
 obj-$(CONFIG_USB_OHCI_HCD)	+= host/
 obj-$(CONFIG_USB_UHCI_HCD)	+= host/
+obj-$(CONFIG_USB_FHCI_HCD)	+= host/
 obj-$(CONFIG_USB_SL811_HCD)	+= host/
 obj-$(CONFIG_USB_U132_HCD)	+= host/
 obj-$(CONFIG_USB_R8A66597_HCD)	+= host/

drivers/usb/host/Kconfig

@@ -239,6 +239,23 @@ config USB_UHCI_HCD
 	  To compile this driver as a module, choose M here: the
 	  module will be called uhci-hcd.
 
+config USB_FHCI_HCD
+	tristate "Freescale QE USB Host Controller support"
+	depends on USB && OF_GPIO && QE_GPIO && QUICC_ENGINE
+	select FSL_GTM
+	select QE_USB
+	help
+	  This driver enables support for Freescale QE USB Host Controller
+	  (as found on MPC8360 and MPC8323 processors), the driver supports
+	  Full and Low Speed USB.
+
+config FHCI_DEBUG
+	bool "Freescale QE USB Host Controller debug support"
+	depends on USB_FHCI_HCD && DEBUG_FS
+	help
+	  Say "y" to see some FHCI debug information and statistics
+	  throught debugfs.
+
 config USB_U132_HCD
 	tristate "Elan U132 Adapter Host Controller"
 	depends on USB && USB_FTDI_ELAN

drivers/usb/host/Makefile

@@ -7,6 +7,11 @@ ifeq ($(CONFIG_USB_DEBUG),y)
 endif
 
 isp1760-objs := isp1760-hcd.o isp1760-if.o
+fhci-objs := fhci-hcd.o fhci-hub.o fhci-q.o fhci-mem.o \
+	     fhci-tds.o fhci-sched.o
+ifeq ($(CONFIG_FHCI_DEBUG),y)
+fhci-objs += fhci-dbg.o
+endif
 
 obj-$(CONFIG_USB_WHCI_HCD)	+= whci/
 
@@ -17,6 +22,7 @@ obj-$(CONFIG_USB_OXU210HP_HCD)	+= oxu210hp-hcd.o
 obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
 obj-$(CONFIG_USB_OHCI_HCD)	+= ohci-hcd.o
 obj-$(CONFIG_USB_UHCI_HCD)	+= uhci-hcd.o
+obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
 obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o
 obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
 obj-$(CONFIG_USB_U132_HCD)	+= u132-hcd.o

drivers/usb/host/fhci-dbg.c

+/*
+ * Freescale QUICC Engine USB Host Controller Driver
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ *               Shlomi Gridish <gridish@freescale.com>
+ *               Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) Logic Product Development, Inc. 2007
+ *               Peter Barada <peterb@logicpd.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *               Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/usb.h>
+#include "../core/hcd.h"
+#include "fhci.h"
+
+void fhci_dbg_isr(struct fhci_hcd *fhci, int usb_er)
+{
+	int i;
+
+	if (usb_er == -1) {
+		fhci->usb_irq_stat[12]++;
+		return;
+	}
+
+	for (i = 0; i < 12; ++i) {
+		if (usb_er & (1 << i))
+			fhci->usb_irq_stat[i]++;
+	}
+}
+
+static int fhci_dfs_regs_show(struct seq_file *s, void *v)
+{
+	struct fhci_hcd *fhci = s->private;
+	struct fhci_regs __iomem *regs = fhci->regs;
+
+	seq_printf(s,
+		"mode: 0x%x\n" "addr: 0x%x\n"
+		"command: 0x%x\n" "ep0: 0x%x\n"
+		"event: 0x%x\n" "mask: 0x%x\n"
+		"status: 0x%x\n" "SOF timer: %d\n"
+		"frame number: %d\n"
+		"lines status: 0x%x\n",
+		in_8(&regs->usb_mod), in_8(&regs->usb_addr),
+		in_8(&regs->usb_comm), in_be16(&regs->usb_ep[0]),
+		in_be16(&regs->usb_event), in_be16(&regs->usb_mask),
+		in_8(&regs->usb_status), in_be16(&regs->usb_sof_tmr),
+		in_be16(&regs->usb_frame_num),
+		fhci_ioports_check_bus_state(fhci));
+
+	return 0;
+}
+
+static int fhci_dfs_irq_stat_show(struct seq_file *s, void *v)
+{
+	struct fhci_hcd *fhci = s->private;
+	int *usb_irq_stat = fhci->usb_irq_stat;
+
+	seq_printf(s,
+		"RXB: %d\n" "TXB: %d\n" "BSY: %d\n"
+		"SOF: %d\n" "TXE0: %d\n" "TXE1: %d\n"
+		"TXE2: %d\n" "TXE3: %d\n" "IDLE: %d\n"
+		"RESET: %d\n" "SFT: %d\n" "MSF: %d\n"
+		"IDLE_ONLY: %d\n",
+		usb_irq_stat[0], usb_irq_stat[1], usb_irq_stat[2],
+		usb_irq_stat[3], usb_irq_stat[4], usb_irq_stat[5],
+		usb_irq_stat[6], usb_irq_stat[7], usb_irq_stat[8],
+		usb_irq_stat[9], usb_irq_stat[10], usb_irq_stat[11],
+		usb_irq_stat[12]);
+
+	return 0;
+}
+
+static int fhci_dfs_regs_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, fhci_dfs_regs_show, inode->i_private);
+}
+
+static int fhci_dfs_irq_stat_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, fhci_dfs_irq_stat_show, inode->i_private);
+}
+
+static const struct file_operations fhci_dfs_regs_fops = {
+	.open = fhci_dfs_regs_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+
+static const struct file_operations fhci_dfs_irq_stat_fops = {
+	.open = fhci_dfs_irq_stat_open,
+	.read = seq_read,
+	.llseek = seq_lseek,
+	.release = single_release,
+};
+
+void fhci_dfs_create(struct fhci_hcd *fhci)
+{
+	struct device *dev = fhci_to_hcd(fhci)->self.controller;
+
+	fhci->dfs_root = debugfs_create_dir(dev->bus_id, NULL);
+	if (!fhci->dfs_root) {
+		WARN_ON(1);
+		return;
+	}
+
+	fhci->dfs_regs = debugfs_create_file("regs", S_IFREG | S_IRUGO,
+		fhci->dfs_root, fhci, &fhci_dfs_regs_fops);
+
+	fhci->dfs_irq_stat = debugfs_create_file("irq_stat",
+		S_IFREG | S_IRUGO, fhci->dfs_root, fhci,
+		&fhci_dfs_irq_stat_fops);
+
+	WARN_ON(!fhci->dfs_regs || !fhci->dfs_irq_stat);
+}
+
+void fhci_dfs_destroy(struct fhci_hcd *fhci)
+{
+	if (!fhci->dfs_root)
+		return;
+
+	if (fhci->dfs_irq_stat)
+		debugfs_remove(fhci->dfs_irq_stat);
+
+	if (fhci->dfs_regs)
+		debugfs_remove(fhci->dfs_regs);
+
+	debugfs_remove(fhci->dfs_root);
+}

drivers/usb/host/fhci-hub.c

+/*
+ * Freescale QUICC Engine USB Host Controller Driver
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ *               Shlomi Gridish <gridish@freescale.com>
+ *               Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) Logic Product Development, Inc. 2007
+ *               Peter Barada <peterb@logicpd.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *               Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/usb.h>
+#include <linux/gpio.h>
+#include <asm/qe.h>
+#include "../core/hcd.h"
+#include "fhci.h"
+
+/* virtual root hub specific descriptor */
+static u8 root_hub_des[] = {
+	0x09, /* blength */
+	0x29, /* bDescriptorType;hub-descriptor */
+	0x01, /* bNbrPorts */
+	0x00, /* wHubCharacteristics */
+	0x00,
+	0x01, /* bPwrOn2pwrGood;2ms */
+	0x00, /* bHubContrCurrent;0mA */
+	0x00, /* DeviceRemoveable */
+	0xff, /* PortPwrCtrlMask */
+};
+
+static void fhci_gpio_set_value(struct fhci_hcd *fhci, int gpio_nr, bool on)
+{
+	int gpio = fhci->gpios[gpio_nr];
+	bool alow = fhci->alow_gpios[gpio_nr];
+
+	if (!gpio_is_valid(gpio))
+		return;
+
+	gpio_set_value(gpio, on ^ alow);
+	mdelay(5);
+}
+
+void fhci_config_transceiver(struct fhci_hcd *fhci,
+			     enum fhci_port_status status)
+{
+	fhci_dbg(fhci, "-> %s: %d\n", __func__, status);
+
+	switch (status) {
+	case FHCI_PORT_POWER_OFF:
+		fhci_gpio_set_value(fhci, GPIO_POWER, false);
+		break;
+	case FHCI_PORT_DISABLED:
+	case FHCI_PORT_WAITING:
+		fhci_gpio_set_value(fhci, GPIO_POWER, true);
+		break;
+	case FHCI_PORT_LOW:
+		fhci_gpio_set_value(fhci, GPIO_SPEED, false);
+		break;
+	case FHCI_PORT_FULL:
+		fhci_gpio_set_value(fhci, GPIO_SPEED, true);
+		break;
+	default:
+		WARN_ON(1);
+		break;
+	}
+
+	fhci_dbg(fhci, "<- %s: %d\n", __func__, status);
+}
+
+/* disable the USB port by clearing the EN bit in the USBMOD register */
+void fhci_port_disable(struct fhci_hcd *fhci)
+{
+	struct fhci_usb *usb = (struct fhci_usb *)fhci->usb_lld;
+	enum fhci_port_status port_status;
+
+	fhci_dbg(fhci, "-> %s\n", __func__);
+
+	fhci_stop_sof_timer(fhci);
+
+	fhci_flush_all_transmissions(usb);
+
+	fhci_usb_disable_interrupt((struct fhci_usb *)fhci->usb_lld);
+	port_status = usb->port_status;
+	usb->port_status = FHCI_PORT_DISABLED;
+
+	/* Enable IDLE since we want to know if something comes along */
+	usb->saved_msk |= USB_E_IDLE_MASK;
+	out_be16(&usb->fhci->regs->usb_mask, usb->saved_msk);
+
+	/* check if during the disconnection process attached new device */
+	if (port_status == FHCI_PORT_WAITING)
+		fhci_device_connected_interrupt(fhci);
+	usb->vroot_hub->port.wPortStatus &= ~USB_PORT_STAT_ENABLE;
+	usb->vroot_hub->port.wPortChange |= USB_PORT_STAT_C_ENABLE;
+	fhci_usb_enable_interrupt((struct fhci_usb *)fhci->usb_lld);
+
+	fhci_dbg(fhci, "<- %s\n", __func__);
+}
+
+/* enable the USB port by setting the EN bit in the USBMOD register */
+void fhci_port_enable(void *lld)
+{
+	struct fhci_usb *usb = (struct fhci_usb *)lld;
+	struct fhci_hcd *fhci = usb->fhci;
+
+	fhci_dbg(fhci, "-> %s\n", __func__);
+
+	fhci_config_transceiver(fhci, usb->port_status);
+
+	if ((usb->port_status != FHCI_PORT_FULL) &&
+			(usb->port_status != FHCI_PORT_LOW))
+		fhci_start_sof_timer(fhci);
+
+	usb->vroot_hub->port.wPortStatus |= USB_PORT_STAT_ENABLE;
+	usb->vroot_hub->port.wPortChange |= USB_PORT_STAT_C_ENABLE;
+
+	fhci_dbg(fhci, "<- %s\n", __func__);
+}
+
+void fhci_io_port_generate_reset(struct fhci_hcd *fhci)
+{
+	fhci_dbg(fhci, "-> %s\n", __func__);
+
+	gpio_direction_output(fhci->gpios[GPIO_USBOE], 0);
+	gpio_direction_output(fhci->gpios[GPIO_USBTP], 0);
+	gpio_direction_output(fhci->gpios[GPIO_USBTN], 0);
+
+	mdelay(5);
+
+	qe_pin_set_dedicated(fhci->pins[PIN_USBOE]);
+	qe_pin_set_dedicated(fhci->pins[PIN_USBTP]);
+	qe_pin_set_dedicated(fhci->pins[PIN_USBTN]);
+
+	fhci_dbg(fhci, "<- %s\n", __func__);
+}
+
+/* generate the RESET condition on the bus */
+void fhci_port_reset(void *lld)
+{
+	struct fhci_usb *usb = (struct fhci_usb *)lld;
+	struct fhci_hcd *fhci = usb->fhci;
+	u8 mode;
+	u16 mask;
+
+	fhci_dbg(fhci, "-> %s\n", __func__);
+
+	fhci_stop_sof_timer(fhci);
+	/* disable the USB controller */
+	mode = in_8(&fhci->regs->usb_mod);
+	out_8(&fhci->regs->usb_mod, mode & (~USB_MODE_EN));
+
+	/* disable idle interrupts */
+	mask = in_be16(&fhci->regs->usb_mask);
+	out_be16(&fhci->regs->usb_mask, mask & (~USB_E_IDLE_MASK));
+
+	fhci_io_port_generate_reset(fhci);
+
+	/* enable interrupt on this endpoint */
+	out_be16(&fhci->regs->usb_mask, mask);
+
+	/* enable the USB controller */
+	mode = in_8(&fhci->regs->usb_mod);
+	out_8(&fhci->regs->usb_mod, mode | USB_MODE_EN);
+	fhci_start_sof_timer(fhci);
+
+	fhci_dbg(fhci, "<- %s\n", __func__);
+}
+
+int fhci_hub_status_data(struct usb_hcd *hcd, char *buf)
+{
+	struct fhci_hcd *fhci = hcd_to_fhci(hcd);
+	int ret = 0;
+	unsigned long flags;
+
+	fhci_dbg(fhci, "-> %s\n", __func__);
+
+	spin_lock_irqsave(&fhci->lock, flags);
+
+	if (fhci->vroot_hub->port.wPortChange & (USB_PORT_STAT_C_CONNECTION |
+			USB_PORT_STAT_C_ENABLE | USB_PORT_STAT_C_SUSPEND |
+			USB_PORT_STAT_C_RESET | USB_PORT_STAT_C_OVERCURRENT)) {
+		*buf = 1 << 1;
+		ret = 1;
+		fhci_dbg(fhci, "-- %s\n", __func__);
+	}
+
+	spin_unlock_irqrestore(&fhci->lock, flags);
+
+	fhci_dbg(fhci, "<- %s\n", __func__);
+
+	return ret;
+}
+
+int fhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
+			    u16 wIndex, char *buf, u16 wLength)
+{
+	struct fhci_hcd *fhci = hcd_to_fhci(hcd);
+	int retval = 0;
+	int len = 0;
+	struct usb_hub_status *hub_status;
+	struct usb_port_status *port_status;
+	unsigned long flags;
+
+	spin_lock_irqsave(&fhci->lock, flags);
+
+	fhci_dbg(fhci, "-> %s\n", __func__);
+
+	switch (typeReq) {
+	case ClearHubFeature:
+		switch (wValue) {
+		case C_HUB_LOCAL_POWER:
+		case C_HUB_OVER_CURRENT:
+			break;
+		default:
+			goto error;
+		}
+		break;
+	case ClearPortFeature:
+		fhci->vroot_hub->feature &= (1 << wValue);
+
+		switch (wValue) {
+		case USB_PORT_FEAT_ENABLE:
+			fhci->vroot_hub->port.wPortStatus &=
+			    ~USB_PORT_STAT_ENABLE;
+			fhci_port_disable(fhci);
+			break;
+		case USB_PORT_FEAT_C_ENABLE:
+			fhci->vroot_hub->port.wPortChange &=
+			    ~USB_PORT_STAT_C_ENABLE;
+			break;
+		case USB_PORT_FEAT_SUSPEND:
+			fhci->vroot_hub->port.wPortStatus &=
+			    ~USB_PORT_STAT_SUSPEND;
+			fhci_stop_sof_timer(fhci);
+			break;
+		case USB_PORT_FEAT_C_SUSPEND:
+			fhci->vroot_hub->port.wPortChange &=
+			    ~USB_PORT_STAT_C_SUSPEND;
+			break;
+		case USB_PORT_FEAT_POWER:
+			fhci->vroot_hub->port.wPortStatus &=
+			    ~USB_PORT_STAT_POWER;
+			fhci_config_transceiver(fhci, FHCI_PORT_POWER_OFF);
+			break;
+		case USB_PORT_FEAT_C_CONNECTION:
+			fhci->vroot_hub->port.wPortChange &=
+			    ~USB_PORT_STAT_C_CONNECTION;
+			break;
+		case USB_PORT_FEAT_C_OVER_CURRENT:
+			fhci->vroot_hub->port.wPortChange &=
+			    ~USB_PORT_STAT_C_OVERCURRENT;
+			break;
+		case USB_PORT_FEAT_C_RESET:
+			fhci->vroot_hub->port.wPortChange &=
+			    ~USB_PORT_STAT_C_RESET;
+			break;
+		default:
+			goto error;
+		}
+		break;
+	case GetHubDescriptor:
+		memcpy(buf, root_hub_des, sizeof(root_hub_des));
+		buf[3] = 0x11; /* per-port power, no ovrcrnt */
+		len = (buf[0] < wLength) ? buf[0] : wLength;
+		break;
+	case GetHubStatus:
+		hub_status = (struct usb_hub_status *)buf;
+		hub_status->wHubStatus =
+		    cpu_to_le16(fhci->vroot_hub->hub.wHubStatus);
+		hub_status->wHubChange =
+		    cpu_to_le16(fhci->vroot_hub->hub.wHubChange);
+		len = 4;
+		break;
+	case GetPortStatus:
+		port_status = (struct usb_port_status *)buf;
+		port_status->wPortStatus =
+		    cpu_to_le16(fhci->vroot_hub->port.wPortStatus);
+		port_status->wPortChange =
+		    cpu_to_le16(fhci->vroot_hub->port.wPortChange);
+		len = 4;
+		break;
+	case SetHubFeature:
+		switch (wValue) {
+		case C_HUB_OVER_CURRENT:
+		case C_HUB_LOCAL_POWER:
+			break;
+		default:
+			goto error;
+		}
+		break;
+	case SetPortFeature:
+		fhci->vroot_hub->feature |= (1 << wValue);
+
+		switch (wValue) {
+		case USB_PORT_FEAT_ENABLE:
+			fhci->vroot_hub->port.wPortStatus |=
+			    USB_PORT_STAT_ENABLE;
+			fhci_port_enable(fhci->usb_lld);
+			break;
+		case USB_PORT_FEAT_SUSPEND:
+			fhci->vroot_hub->port.wPortStatus |=
+			    USB_PORT_STAT_SUSPEND;
+			fhci_stop_sof_timer(fhci);
+			break;
+		case USB_PORT_FEAT_RESET:
+			fhci->vroot_hub->port.wPortStatus |=
+			    USB_PORT_STAT_RESET;
+			fhci_port_reset(fhci->usb_lld);
+			fhci->vroot_hub->port.wPortStatus |=
+			    USB_PORT_STAT_ENABLE;
+			fhci->vroot_hub->port.wPortStatus &=
+			    ~USB_PORT_STAT_RESET;
+			break;
+		case USB_PORT_FEAT_POWER:
+			fhci->vroot_hub->port.wPortStatus |=
+			    USB_PORT_STAT_POWER;
+			fhci_config_transceiver(fhci, FHCI_PORT_WAITING);
+			break;
+		default:
+			goto error;
+		}
+		break;
+	default:
+error:
+		retval = -EPIPE;
+	}
+
+	fhci_dbg(fhci, "<- %s\n", __func__);
+
+	spin_unlock_irqrestore(&fhci->lock, flags);
+
+	return retval;
+}

drivers/usb/host/fhci-mem.c

+/*
+ * Freescale QUICC Engine USB Host Controller Driver
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ *               Shlomi Gridish <gridish@freescale.com>
+ *               Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) Logic Product Development, Inc. 2007
+ *               Peter Barada <peterb@logicpd.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *               Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/list.h>
+#include <linux/usb.h>
+#include "../core/hcd.h"
+#include "fhci.h"
+
+static void init_td(struct td *td)
+{
+	memset(td, 0, sizeof(*td));
+	INIT_LIST_HEAD(&td->node);
+	INIT_LIST_HEAD(&td->frame_lh);
+}
+
+static void init_ed(struct ed *ed)
+{
+	memset(ed, 0, sizeof(*ed));
+	INIT_LIST_HEAD(&ed->td_list);
+	INIT_LIST_HEAD(&ed->node);
+}
+
+static struct td *get_empty_td(struct fhci_hcd *fhci)
+{
+	struct td *td;
+
+	if (!list_empty(&fhci->empty_tds)) {
+		td = list_entry(fhci->empty_tds.next, struct td, node);
+		list_del(fhci->empty_tds.next);
+	} else {
+		td = kmalloc(sizeof(*td), GFP_ATOMIC);
+		if (!td)
+			fhci_err(fhci, "No memory to allocate to TD\n");
+		else
+			init_td(td);
+	}
+
+	return td;
+}
+
+void fhci_recycle_empty_td(struct fhci_hcd *fhci, struct td *td)
+{
+	init_td(td);
+	list_add(&td->node, &fhci->empty_tds);
+}
+
+struct ed *fhci_get_empty_ed(struct fhci_hcd *fhci)
+{
+	struct ed *ed;
+
+	if (!list_empty(&fhci->empty_eds)) {
+		ed = list_entry(fhci->empty_eds.next, struct ed, node);
+		list_del(fhci->empty_eds.next);
+	} else {
+		ed = kmalloc(sizeof(*ed), GFP_ATOMIC);
+		if (!ed)
+			fhci_err(fhci, "No memory to allocate to ED\n");
+		else
+			init_ed(ed);
+	}
+
+	return ed;
+}
+
+void fhci_recycle_empty_ed(struct fhci_hcd *fhci, struct ed *ed)
+{
+	init_ed(ed);
+	list_add(&ed->node, &fhci->empty_eds);
+}
+
+struct td *fhci_td_fill(struct fhci_hcd *fhci, struct urb *urb,
+			struct urb_priv *urb_priv, struct ed *ed, u16 index,
+			enum fhci_ta_type type, int toggle, u8 *data, u32 len,
+			u16 interval, u16 start_frame, bool ioc)
+{
+	struct td *td = get_empty_td(fhci);
+
+	if (!td)
+		return NULL;
+
+	td->urb = urb;
+	td->ed = ed;
+	td->type = type;
+	td->toggle = toggle;
+	td->data = data;
+	td->len = len;
+	td->iso_index = index;
+	td->interval = interval;
+	td->start_frame = start_frame;
+	td->ioc = ioc;
+	td->status = USB_TD_OK;
+
+	urb_priv->tds[index] = td;
+
+	return td;
+}

drivers/usb/host/fhci-q.c

+/*
+ * Freescale QUICC Engine USB Host Controller Driver
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ *               Shlomi Gridish <gridish@freescale.com>
+ *               Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) Logic Product Development, Inc. 2007
+ *               Peter Barada <peterb@logicpd.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *               Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/list.h>
+#include <linux/usb.h>
+#include "../core/hcd.h"
+#include "fhci.h"
+
+/* maps the hardware error code to the USB error code */
+static int status_to_error(u32 status)
+{
+	if (status == USB_TD_OK)
+		return 0;
+	else if (status & USB_TD_RX_ER_CRC)
+		return -EILSEQ;
+	else if (status & USB_TD_RX_ER_NONOCT)
+		return -EPROTO;
+	else if (status & USB_TD_RX_ER_OVERUN)
+		return -ECOMM;
+	else if (status & USB_TD_RX_ER_BITSTUFF)
+		return -EPROTO;
+	else if (status & USB_TD_RX_ER_PID)
+		return -EILSEQ;
+	else if (status & (USB_TD_TX_ER_NAK | USB_TD_TX_ER_TIMEOUT))
+		return -ETIMEDOUT;
+	else if (status & USB_TD_TX_ER_STALL)
+		return -EPIPE;
+	else if (status & USB_TD_TX_ER_UNDERUN)
+		return -ENOSR;
+	else if (status & USB_TD_RX_DATA_UNDERUN)
+		return -EREMOTEIO;
+	else if (status & USB_TD_RX_DATA_OVERUN)
+		return -EOVERFLOW;
+	else
+		return -EINVAL;
+}
+
+void fhci_add_td_to_frame(struct fhci_time_frame *frame, struct td *td)
+{
+	list_add_tail(&td->frame_lh, &frame->tds_list);
+}
+
+void fhci_add_tds_to_ed(struct ed *ed, struct td **td_list, int number)
+{
+	int i;
+
+	for (i = 0; i < number; i++) {
+		struct td *td = td_list[i];
+		list_add_tail(&td->node, &ed->td_list);
+	}
+	if (ed->td_head == NULL)
+		ed->td_head = td_list[0];
+}
+
+static struct td *peek_td_from_ed(struct ed *ed)
+{
+	struct td *td;
+
+	if (!list_empty(&ed->td_list))
+		td = list_entry(ed->td_list.next, struct td, node);
+	else
+		td = NULL;
+
+	return td;
+}
+
+struct td *fhci_remove_td_from_frame(struct fhci_time_frame *frame)
+{
+	struct td *td;
+
+	if (!list_empty(&frame->tds_list)) {
+		td = list_entry(frame->tds_list.next, struct td, frame_lh);
+		list_del_init(frame->tds_list.next);
+	} else
+		td = NULL;
+
+	return td;
+}
+
+struct td *fhci_peek_td_from_frame(struct fhci_time_frame *frame)
+{
+	struct td *td;
+
+	if (!list_empty(&frame->tds_list))
+		td = list_entry(frame->tds_list.next, struct td, frame_lh);
+	else
+		td = NULL;
+
+	return td;
+}
+
+struct td *fhci_remove_td_from_ed(struct ed *ed)
+{
+	struct td *td;
+
+	if (!list_empty(&ed->td_list)) {
+		td = list_entry(ed->td_list.next, struct td, node);
+		list_del_init(ed->td_list.next);
+
+		/* if this TD was the ED's head, find next TD */
+		if (!list_empty(&ed->td_list))
+			ed->td_head = list_entry(ed->td_list.next, struct td,
+						 node);
+		else
+			ed->td_head = NULL;
+	} else
+		td = NULL;
+
+	return td;
+}
+
+struct td *fhci_remove_td_from_done_list(struct fhci_controller_list *p_list)
+{
+	struct td *td;
+
+	if (!list_empty(&p_list->done_list)) {
+		td = list_entry(p_list->done_list.next, struct td, node);
+		list_del_init(p_list->done_list.next);
+	} else
+		td = NULL;
+
+	return td;
+}
+
+void fhci_move_td_from_ed_to_done_list(struct fhci_usb *usb, struct ed *ed)
+{
+	struct td *td;
+
+	td = ed->td_head;
+	list_del_init(&td->node);
+
+	/* If this TD was the ED's head,find next TD */
+	if (!list_empty(&ed->td_list))
+		ed->td_head = list_entry(ed->td_list.next, struct td, node);
+	else {
+		ed->td_head = NULL;
+		ed->state = FHCI_ED_SKIP;
+	}
+	ed->toggle_carry = td->toggle;
+	list_add_tail(&td->node, &usb->hc_list->done_list);
+	if (td->ioc)
+		usb->transfer_confirm(usb->fhci);
+}
+
+/* free done FHCI URB resource such as ED and TD */
+static void free_urb_priv(struct fhci_hcd *fhci, struct urb *urb)
+{
+	int i;
+	struct urb_priv *urb_priv = urb->hcpriv;
+	struct ed *ed = urb_priv->ed;
+
+	for (i = 0; i < urb_priv->num_of_tds; i++) {
+		list_del_init(&urb_priv->tds[i]->node);
+		fhci_recycle_empty_td(fhci, urb_priv->tds[i]);
+	}
+
+	/* if this TD was the ED's head,find the next TD */
+	if (!list_empty(&ed->td_list))
+		ed->td_head = list_entry(ed->td_list.next, struct td, node);
+	else
+		ed->td_head = NULL;
+
+	kfree(urb_priv->tds);
+	kfree(urb_priv);
+	urb->hcpriv = NULL;
+
+	/* if this TD was the ED's head,find next TD */
+	if (ed->td_head == NULL)
+		list_del_init(&ed->node);
+	fhci->active_urbs--;
+}
+
+/* this routine called to complete and free done URB */
+void fhci_urb_complete_free(struct fhci_hcd *fhci, struct urb *urb)
+{
+	free_urb_priv(fhci, urb);
+
+	if (urb->status == -EINPROGRESS) {
+		if (urb->actual_length != urb->transfer_buffer_length &&
+				urb->transfer_flags & URB_SHORT_NOT_OK)
+			urb->status = -EREMOTEIO;
+		else
+			urb->status = 0;
+	}
+
+	usb_hcd_unlink_urb_from_ep(fhci_to_hcd(fhci), urb);
+
+	spin_unlock(&fhci->lock);
+
+	usb_hcd_giveback_urb(fhci_to_hcd(fhci), urb, urb->status);
+
+	spin_lock(&fhci->lock);
+}
+
+/*
+ * caculate transfer length/stats and update the urb
+ * Precondition: irqsafe(only for urb-?status locking)
+ */
+void fhci_done_td(struct urb *urb, struct td *td)
+{
+	struct ed *ed = td->ed;
+	u32 cc = td->status;
+
+	/* ISO...drivers see per-TD length/status */
+	if (ed->mode == FHCI_TF_ISO) {
+		u32 len;
+		if (!(urb->transfer_flags & URB_SHORT_NOT_OK &&
+				cc == USB_TD_RX_DATA_UNDERUN))
+			cc = USB_TD_OK;
+
+		if (usb_pipeout(urb->pipe))
+			len = urb->iso_frame_desc[td->iso_index].length;
+		else
+			len = td->actual_len;
+
+		urb->actual_length += len;
+		urb->iso_frame_desc[td->iso_index].actual_length = len;
+		urb->iso_frame_desc[td->iso_index].status =
+			status_to_error(cc);
+	}
+
+	/* BULK,INT,CONTROL... drivers see aggregate length/status,
+	 * except that "setup" bytes aren't counted and "short" transfers
+	 * might not be reported as errors.
+	 */
+	else {
+		if (td->error_cnt >= 3)
+			urb->error_count = 3;
+
+		/* control endpoint only have soft stalls */
+
+		/* update packet status if needed(short may be ok) */
+		if (!(urb->transfer_flags & URB_SHORT_NOT_OK) &&
+				cc == USB_TD_RX_DATA_UNDERUN) {
+			ed->state = FHCI_ED_OPER;
+			cc = USB_TD_OK;
+		}
+		if (cc != USB_TD_OK) {
+			if (urb->status == -EINPROGRESS)
+				urb->status = status_to_error(cc);
+		}
+
+		/* count all non-empty packets except control SETUP packet */
+		if (td->type != FHCI_TA_SETUP || td->iso_index != 0)
+			urb->actual_length += td->actual_len;
+	}
+}
+
+/* there are some pedning request to unlink */
+void fhci_del_ed_list(struct fhci_hcd *fhci, struct ed *ed)
+{
+	struct td *td = peek_td_from_ed(ed);
+	struct urb *urb = td->urb;
+	struct urb_priv *urb_priv = urb->hcpriv;
+
+	if (urb_priv->state == URB_DEL) {
+		td = fhci_remove_td_from_ed(ed);
+		/* HC may have partly processed this TD */
+		if (td->status != USB_TD_INPROGRESS)
+			fhci_done_td(urb, td);
+
+		/* URB is done;clean up */
+		if (++(urb_priv->tds_cnt) == urb_priv->num_of_tds)
+			fhci_urb_complete_free(fhci, urb);
+	}
+}

drivers/usb/host/fhci-tds.c

+/*
+ * Freescale QUICC Engine USB Host Controller Driver
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ *               Shlomi Gridish <gridish@freescale.com>
+ *               Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) Logic Product Development, Inc. 2007
+ *               Peter Barada <peterb@logicpd.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *               Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/list.h>
+#include <linux/io.h>
+#include <linux/usb.h>
+#include "../core/hcd.h"
+#include "fhci.h"
+
+#define DUMMY_BD_BUFFER  0xdeadbeef
+#define DUMMY2_BD_BUFFER 0xbaadf00d
+
+/* Transaction Descriptors bits */
+#define TD_R		0x8000 /* ready bit */
+#define TD_W		0x2000 /* wrap bit */
+#define TD_I		0x1000 /* interrupt on completion */
+#define TD_L		0x0800 /* last */
+#define TD_TC		0x0400 /* transmit CRC */
+#define TD_CNF		0x0200 /* CNF - Must be always 1 */
+#define TD_LSP		0x0100 /* Low-speed transaction */
+#define TD_PID		0x00c0 /* packet id */
+#define TD_RXER		0x0020 /* Rx error or not */
+
+#define TD_NAK		0x0010 /* No ack. */
+#define TD_STAL		0x0008 /* Stall recieved */
+#define TD_TO		0x0004 /* time out */
+#define TD_UN		0x0002 /* underrun */
+#define TD_NO		0x0010 /* Rx Non Octet Aligned Packet */
+#define TD_AB		0x0008 /* Frame Aborted */
+#define TD_CR		0x0004 /* CRC Error */
+#define TD_OV		0x0002 /* Overrun */
+#define TD_BOV		0x0001 /* Buffer Overrun */
+
+#define TD_ERRORS	(TD_NAK | TD_STAL | TD_TO | TD_UN | \
+			 TD_NO | TD_AB | TD_CR | TD_OV | TD_BOV)
+
+#define TD_PID_DATA0	0x0080 /* Data 0 toggle */
+#define TD_PID_DATA1	0x00c0 /* Data 1 toggle */
+#define TD_PID_TOGGLE	0x00c0 /* Data 0/1 toggle mask */
+
+#define TD_TOK_SETUP	0x0000
+#define TD_TOK_OUT	0x4000
+#define TD_TOK_IN	0x8000
+#define TD_ISO		0x1000
+#define TD_ENDP		0x0780
+#define TD_ADDR		0x007f
+
+#define TD_ENDP_SHIFT 7
+
+struct usb_td {
+	__be16 status;
+	__be16 length;
+	__be32 buf_ptr;
+	__be16 extra;
+	__be16 reserved;
+};
+
+static struct usb_td __iomem *next_bd(struct usb_td __iomem *base,
+				      struct usb_td __iomem *td,
+				      u16 status)
+{
+	if (status & TD_W)
+		return base;
+	else
+		return ++td;
+}
+
+void fhci_push_dummy_bd(struct endpoint *ep)
+{
+	if (ep->already_pushed_dummy_bd == false) {
+		u16 td_status = in_be16(&ep->empty_td->status);
+
+		out_be32(&ep->empty_td->buf_ptr, DUMMY_BD_BUFFER);
+		/* get the next TD in the ring */
+		ep->empty_td = next_bd(ep->td_base, ep->empty_td, td_status);
+		ep->already_pushed_dummy_bd = true;
+	}
+}
+
+/* destroy an USB endpoint */
+void fhci_ep0_free(struct fhci_usb *usb)
+{
+	struct endpoint *ep;
+	int size;
+
+	ep = usb->ep0;
+	if (ep) {
+		if (ep->td_base)
+			cpm_muram_free(cpm_muram_offset(ep->td_base));
+
+		if (ep->conf_frame_Q) {
+			size = cq_howmany(ep->conf_frame_Q);
+			for (; size; size--) {
+				struct packet *pkt = cq_get(ep->conf_frame_Q);
+
+				kfree(pkt);
+			}
+			cq_delete(ep->conf_frame_Q);
+		}
+
+		if (ep->empty_frame_Q) {
+			size = cq_howmany(ep->empty_frame_Q);
+			for (; size; size--) {
+				struct packet *pkt = cq_get(ep->empty_frame_Q);
+
+				kfree(pkt);
+			}
+			cq_delete(ep->empty_frame_Q);
+		}
+
+		if (ep->dummy_packets_Q) {
+			size = cq_howmany(ep->dummy_packets_Q);
+			for (; size; size--) {
+				u8 *buff = cq_get(ep->dummy_packets_Q);
+
+				kfree(buff);
+			}
+			cq_delete(ep->dummy_packets_Q);
+		}
+
+		kfree(ep);
+		usb->ep0 = NULL;
+	}
+}
+
+/*
+ * create the endpoint structure
+ *
+ * arguments:
+ * usb		A pointer to the data structure of the USB
+ * data_mem	The data memory partition(BUS)
+ * ring_len	TD ring length
+ */
+u32 fhci_create_ep(struct fhci_usb *usb, enum fhci_mem_alloc data_mem,
+			   u32 ring_len)
+{
+	struct endpoint *ep;
+	struct usb_td __iomem *td;
+	unsigned long ep_offset;
+	char *err_for = "enpoint PRAM";
+	int ep_mem_size;
+	u32 i;
+
+	/* we need at least 3 TDs in the ring */
+	if (!(ring_len > 2)) {
+		fhci_err(usb->fhci, "illegal TD ring length parameters\n");
+		return -EINVAL;
+	}
+
+	ep = kzalloc(sizeof(*ep), GFP_KERNEL);
+	if (!ep)
+		return -ENOMEM;
+
+	ep_mem_size = ring_len * sizeof(*td) + sizeof(struct fhci_ep_pram);
+	ep_offset = cpm_muram_alloc(ep_mem_size, 32);
+	if (IS_ERR_VALUE(ep_offset))
+		goto err;
+	ep->td_base = cpm_muram_addr(ep_offset);
+
+	/* zero all queue pointers */
+	ep->conf_frame_Q = cq_new(ring_len + 2);
+	ep->empty_frame_Q = cq_new(ring_len + 2);
+	ep->dummy_packets_Q = cq_new(ring_len + 2);
+	if (!ep->conf_frame_Q || !ep->empty_frame_Q || !ep->dummy_packets_Q) {
+		err_for = "frame_queues";
+		goto err;
+	}
+
+	for (i = 0; i < (ring_len + 1); i++) {
+		struct packet *pkt;
+		u8 *buff;
+
+		pkt = kmalloc(sizeof(*pkt), GFP_KERNEL);
+		if (!pkt) {
+			err_for = "frame";
+			goto err;
+		}
+
+		buff = kmalloc(1028 * sizeof(*buff), GFP_KERNEL);
+		if (!buff) {
+			kfree(pkt);
+			err_for = "buffer";
+			goto err;
+		}
+		cq_put(ep->empty_frame_Q, pkt);
+		cq_put(ep->dummy_packets_Q, buff);
+	}
+
+	/* we put the endpoint parameter RAM right behind the TD ring */
+	ep->ep_pram_ptr = (void __iomem *)ep->td_base + sizeof(*td) * ring_len;
+
+	ep->conf_td = ep->td_base;
+	ep->empty_td = ep->td_base;
+
+	ep->already_pushed_dummy_bd = false;
+
+	/* initialize tds */
+	td = ep->td_base;
+	for (i = 0; i < ring_len; i++) {
+		out_be32(&td->buf_ptr, 0);
+		out_be16(&td->status, 0);
+		out_be16(&td->length, 0);
+		out_be16(&td->extra, 0);
+		td++;
+	}
+	td--;
+	out_be16(&td->status, TD_W); /* for last TD set Wrap bit */
+	out_be16(&td->length, 0);
+
+	/* endpoint structure has been created */
+	usb->ep0 = ep;
+
+	return 0;
+err:
+	fhci_ep0_free(usb);
+	kfree(ep);
+	fhci_err(usb->fhci, "no memory for the %s\n", err_for);
+	return -ENOMEM;
+}
+
+/*
+ * initialize the endpoint register according to the given parameters
+ *
+ * artuments:
+ * usb		A pointer to the data strucutre of the USB
+ * ep		A pointer to the endpoint structre
+ * data_mem	The data memory partition(BUS)
+ */
+void fhci_init_ep_registers(struct fhci_usb *usb, struct endpoint *ep,
+			    enum fhci_mem_alloc data_mem)
+{
+	u8 rt;
+
+	/* set the endpoint registers according to the endpoint */
+	out_be16(&usb->fhci->regs->usb_ep[0],
+		 USB_TRANS_CTR | USB_EP_MF | USB_EP_RTE);
+	out_be16(&usb->fhci->pram->ep_ptr[0],
+		 cpm_muram_offset(ep->ep_pram_ptr));
+
+	rt = (BUS_MODE_BO_BE | BUS_MODE_GBL);
+#ifdef MULTI_DATA_BUS
+	if (data_mem == MEM_SECONDARY)
+		rt |= BUS_MODE_DTB;
+#endif
+	out_8(&ep->ep_pram_ptr->rx_func_code, rt);
+	out_8(&ep->ep_pram_ptr->tx_func_code, rt);
+	out_be16(&ep->ep_pram_ptr->rx_buff_len, 1028);
+	out_be16(&ep->ep_pram_ptr->rx_base, 0);
+	out_be16(&ep->ep_pram_ptr->tx_base, cpm_muram_offset(ep->td_base));
+	out_be16(&ep->ep_pram_ptr->rx_bd_ptr, 0);
+	out_be16(&ep->ep_pram_ptr->tx_bd_ptr, cpm_muram_offset(ep->td_base));
+	out_be32(&ep->ep_pram_ptr->tx_state, 0);
+}
+
+/*
+ * Collect the submitted frames and inform the application about them
+ * It is also prepearing the TDs for new frames. If the Tx interrupts
+ * are diabled, the application should call that routine to get
+ * confirmation about the submitted frames. Otherwise, the routine is
+ * called frome the interrupt service routine during the Tx interrupt.
+ * In that case the application is informed by calling the application
+ * specific 'fhci_transaction_confirm' routine
+ */
+static void fhci_td_transaction_confirm(struct fhci_usb *usb)
+{
+	struct endpoint *ep = usb->ep0;
+	struct packet *pkt;
+	struct usb_td __iomem *td;
+	u16 extra_data;
+	u16 td_status;
+	u16 td_length;
+	u32 buf;
+
+	/*
+	 * collect transmitted BDs from the chip. The routine clears all BDs
+	 * with R bit = 0 and the pointer to data buffer is not NULL, that is
+	 * BDs which point to the transmitted data buffer
+	 */
+	while (1) {
+		td = ep->conf_td;
+		td_status = in_be16(&td->status);
+		td_length = in_be16(&td->length);
+		buf = in_be32(&td->buf_ptr);
+		extra_data = in_be16(&td->extra);
+
+		/* check if the TD is empty */
+		if (!(!(td_status & TD_R) && ((td_status & ~TD_W) || buf)))
+			break;
+		/* check if it is a dummy buffer */
+		else if ((buf == DUMMY_BD_BUFFER) && !(td_status & ~TD_W))
+			break;
+
+		/* mark TD as empty */
+		clrbits16(&td->status, ~TD_W);
+		out_be16(&td->length, 0);
+		out_be32(&td->buf_ptr, 0);
+		out_be16(&td->extra, 0);
+		/* advance the TD pointer */
+		ep->conf_td = next_bd(ep->td_base, ep->conf_td, td_status);
+
+		/* check if it is a dummy buffer(type2) */
+		if ((buf == DUMMY2_BD_BUFFER) && !(td_status & ~TD_W))
+			continue;
+
+		pkt = cq_get(ep->conf_frame_Q);
+		if (!pkt)
+			fhci_err(usb->fhci, "no frame to confirm\n");
+
+		if (td_status & TD_ERRORS) {
+			if (td_status & TD_RXER) {
+				if (td_status & TD_CR)
+					pkt->status = USB_TD_RX_ER_CRC;
+				else if (td_status & TD_AB)
+					pkt->status = USB_TD_RX_ER_BITSTUFF;
+				else if (td_status & TD_OV)
+					pkt->status = USB_TD_RX_ER_OVERUN;
+				else if (td_status & TD_BOV)
+					pkt->status = USB_TD_RX_DATA_OVERUN;
+				else if (td_status & TD_NO)
+					pkt->status = USB_TD_RX_ER_NONOCT;
+				else
+					fhci_err(usb->fhci, "illegal error "
+						 "occured\n");
+			} else if (td_status & TD_NAK)
+				pkt->status = USB_TD_TX_ER_NAK;
+			else if (td_status & TD_TO)
+				pkt->status = USB_TD_TX_ER_TIMEOUT;
+			else if (td_status & TD_UN)
+				pkt->status = USB_TD_TX_ER_UNDERUN;
+			else if (td_status & TD_STAL)
+				pkt->status = USB_TD_TX_ER_STALL;
+			else
+				fhci_err(usb->fhci, "illegal error occured\n");
+		} else if ((extra_data & TD_TOK_IN) &&
+				pkt->len > td_length - CRC_SIZE) {
+			pkt->status = USB_TD_RX_DATA_UNDERUN;
+		}
+
+		if (extra_data & TD_TOK_IN)
+			pkt->len = td_length - CRC_SIZE;
+		else if (pkt->info & PKT_ZLP)
+			pkt->len = 0;
+		else
+			pkt->len = td_length;
+
+		fhci_transaction_confirm(usb, pkt);
+	}
+}
+
+/*
+ * Submitting a data frame to a specified endpoint of a USB device
+ * The frame is put in the driver's transmit queue for this endpoint
+ *
+ * Arguments:
+ * usb          A pointer to the USB structure
+ * pkt          A pointer to the user frame structure
+ * trans_type   Transaction tyep - IN,OUT or SETUP
+ * dest_addr    Device address - 0~127
+ * dest_ep      Endpoint number of the device - 0~16
+ * trans_mode   Pipe type - ISO,Interrupt,bulk or control
+ * dest_speed   USB speed - Low speed or FULL speed
+ * data_toggle  Data sequence toggle - 0 or 1
+ */
+u32 fhci_host_transaction(struct fhci_usb *usb,
+			  struct packet *pkt,
+			  enum fhci_ta_type trans_type,
+			  u8 dest_addr,
+			  u8 dest_ep,
+			  enum fhci_tf_mode trans_mode,
+			  enum fhci_speed dest_speed, u8 data_toggle)
+{
+	struct endpoint *ep = usb->ep0;
+	struct usb_td __iomem *td;
+	u16 extra_data;
+	u16 td_status;
+
+	fhci_usb_disable_interrupt(usb);
+	/* start from the next BD that should be filled */
+	td = ep->empty_td;
+	td_status = in_be16(&td->status);
+
+	if (td_status & TD_R && in_be16(&td->length)) {
+		/* if the TD is not free */
+		fhci_usb_enable_interrupt(usb);
+		return -1;
+	}
+
+	/* get the next TD in the ring */
+	ep->empty_td = next_bd(ep->td_base, ep->empty_td, td_status);
+	fhci_usb_enable_interrupt(usb);
+	pkt->priv_data = td;
+	out_be32(&td->buf_ptr, virt_to_phys(pkt->data));
+	/* sets up transaction parameters - addr,endp,dir,and type */
+	extra_data = (dest_ep << TD_ENDP_SHIFT) | dest_addr;
+	switch (trans_type) {
+	case FHCI_TA_IN:
+		extra_data |= TD_TOK_IN;
+		break;
+	case FHCI_TA_OUT:
+		extra_data |= TD_TOK_OUT;
+		break;
+	case FHCI_TA_SETUP:
+		extra_data |= TD_TOK_SETUP;
+		break;
+	}
+	if (trans_mode == FHCI_TF_ISO)
+		extra_data |= TD_ISO;
+	out_be16(&td->extra, extra_data);
+
+	/* sets up the buffer descriptor */
+	td_status = ((td_status & TD_W) | TD_R | TD_L | TD_I | TD_CNF);
+	if (!(pkt->info & PKT_NO_CRC))
+		td_status |= TD_TC;
+
+	switch (trans_type) {
+	case FHCI_TA_IN:
+		if (data_toggle)
+			pkt->info |= PKT_PID_DATA1;
+		else
+			pkt->info |= PKT_PID_DATA0;
+		break;
+	default:
+		if (data_toggle) {
+			td_status |= TD_PID_DATA1;
+			pkt->info |= PKT_PID_DATA1;
+		} else {
+			td_status |= TD_PID_DATA0;
+			pkt->info |= PKT_PID_DATA0;
+		}
+		break;
+	}
+
+	if ((dest_speed == FHCI_LOW_SPEED) &&
+	    (usb->port_status == FHCI_PORT_FULL))
+		td_status |= TD_LSP;
+
+	out_be16(&td->status, td_status);
+
+	/* set up buffer length */
+	if (trans_type == FHCI_TA_IN)
+		out_be16(&td->length, pkt->len + CRC_SIZE);
+	else
+		out_be16(&td->length, pkt->len);
+
+	/* put the frame to the confirmation queue */
+	cq_put(ep->conf_frame_Q, pkt);
+
+	if (cq_howmany(ep->conf_frame_Q) == 1)
+		out_8(&usb->fhci->regs->usb_comm, USB_CMD_STR_FIFO);
+
+	return 0;
+}
+
+/* Reset the Tx BD ring */
+void fhci_flush_bds(struct fhci_usb *usb)
+{
+	u16 extra_data;
+	u16 td_status;
+	u32 buf;
+	struct usb_td __iomem *td;
+	struct endpoint *ep = usb->ep0;
+
+	td = ep->td_base;
+	while (1) {
+		td_status = in_be16(&td->status);
+		buf = in_be32(&td->buf_ptr);
+		extra_data = in_be16(&td->extra);
+
+		/* if the TD is not empty - we'll confirm it as Timeout */
+		if (td_status & TD_R)
+			out_be16(&td->status, (td_status & ~TD_R) | TD_TO);
+		/* if this TD is dummy - let's skip this TD */
+		else if (in_be32(&td->buf_ptr) == DUMMY_BD_BUFFER)
+			out_be32(&td->buf_ptr, DUMMY2_BD_BUFFER);
+		/* if this is the last TD - break */
+		if (td_status & TD_W)
+			break;
+
+		td++;
+	}
+
+	fhci_td_transaction_confirm(usb);
+
+	td = ep->td_base;
+	do {
+		out_be16(&td->status, 0);
+		out_be16(&td->length, 0);
+		out_be32(&td->buf_ptr, 0);
+		out_be16(&td->extra, 0);
+		td++;
+	} while (!(in_be16(&td->status) & TD_W));
+	out_be16(&td->status, TD_W); /* for last TD set Wrap bit */
+	out_be16(&td->length, 0);
+	out_be32(&td->buf_ptr, 0);
+	out_be16(&td->extra, 0);
+
+	out_be16(&ep->ep_pram_ptr->tx_bd_ptr,
+		 in_be16(&ep->ep_pram_ptr->tx_base));
+	out_be32(&ep->ep_pram_ptr->tx_state, 0);
+	out_be16(&ep->ep_pram_ptr->tx_cnt, 0);
+	ep->empty_td = ep->td_base;
+	ep->conf_td = ep->td_base;
+}
+
+/*
+ * Flush all transmitted packets from TDs in the actual frame.
+ * This routine is called when something wrong with the controller and
+ * we want to get rid of the actual frame and start again next frame
+ */
+void fhci_flush_actual_frame(struct fhci_usb *usb)
+{
+	u8 mode;
+	u16 tb_ptr;
+	u16 extra_data;
+	u16 td_status;
+	u32 buf_ptr;
+	struct usb_td __iomem *td;
+	struct endpoint *ep = usb->ep0;
+
+	/* disable the USB controller */
+	mode = in_8(&usb->fhci->regs->usb_mod);
+	out_8(&usb->fhci->regs->usb_mod, mode & ~USB_MODE_EN);
+
+	tb_ptr = in_be16(&ep->ep_pram_ptr->tx_bd_ptr);
+	td = cpm_muram_addr(tb_ptr);
+	td_status = in_be16(&td->status);
+	buf_ptr = in_be32(&td->buf_ptr);
+	extra_data = in_be16(&td->extra);
+	do {
+		if (td_status & TD_R) {
+			out_be16(&td->status, (td_status & ~TD_R) | TD_TO);
+		} else {
+			out_be32(&td->buf_ptr, 0);
+			ep->already_pushed_dummy_bd = false;
+			break;
+		}
+
+		/* advance the TD pointer */
+		td = next_bd(ep->td_base, td, td_status);
+		td_status = in_be16(&td->status);
+		buf_ptr = in_be32(&td->buf_ptr);
+		extra_data = in_be16(&td->extra);
+	} while ((td_status & TD_R) || buf_ptr);
+
+	fhci_td_transaction_confirm(usb);
+
+	out_be16(&ep->ep_pram_ptr->tx_bd_ptr,
+		 in_be16(&ep->ep_pram_ptr->tx_base));
+	out_be32(&ep->ep_pram_ptr->tx_state, 0);
+	out_be16(&ep->ep_pram_ptr->tx_cnt, 0);
+	ep->empty_td = ep->td_base;
+	ep->conf_td = ep->td_base;
+
+	usb->actual_frame->frame_status = FRAME_TIMER_END_TRANSMISSION;
+
+	/* reset the event register */
+	out_be16(&usb->fhci->regs->usb_event, 0xffff);
+	/* enable the USB controller */
+	out_8(&usb->fhci->regs->usb_mod, mode | USB_MODE_EN);
+}
+
+/* handles Tx confirm and Tx error interrupt */
+void fhci_tx_conf_interrupt(struct fhci_usb *usb)
+{
+	fhci_td_transaction_confirm(usb);
+
+	/*
+	 * Schedule another transaction to this frame only if we have
+	 * already confirmed all transaction in the frame.
+	 */
+	if (((fhci_get_sof_timer_count(usb) < usb->max_frame_usage) ||
+	     (usb->actual_frame->frame_status & FRAME_END_TRANSMISSION)) &&
+	    (list_empty(&usb->actual_frame->tds_list)))
+		fhci_schedule_transactions(usb);
+}
+
+void fhci_host_transmit_actual_frame(struct fhci_usb *usb)
+{
+	u16 tb_ptr;
+	u16 td_status;
+	struct usb_td __iomem *td;
+	struct endpoint *ep = usb->ep0;
+
+	tb_ptr = in_be16(&ep->ep_pram_ptr->tx_bd_ptr);
+	td = cpm_muram_addr(tb_ptr);
+
+	if (in_be32(&td->buf_ptr) == DUMMY_BD_BUFFER) {
+		struct usb_td __iomem *old_td = td;
+
+		ep->already_pushed_dummy_bd = false;
+		td_status = in_be16(&td->status);
+		/* gets the next TD in the ring */
+		td = next_bd(ep->td_base, td, td_status);
+		tb_ptr = cpm_muram_offset(td);
+		out_be16(&ep->ep_pram_ptr->tx_bd_ptr, tb_ptr);
+
+		/* start transmit only if we have something in the TDs */
+		if (in_be16(&td->status) & TD_R)
+			out_8(&usb->fhci->regs->usb_comm, USB_CMD_STR_FIFO);
+
+		if (in_be32(&ep->conf_td->buf_ptr) == DUMMY_BD_BUFFER) {
+			out_be32(&old_td->buf_ptr, 0);
+			ep->conf_td = next_bd(ep->td_base, ep->conf_td,
+					      td_status);
+		} else {
+			out_be32(&old_td->buf_ptr, DUMMY2_BD_BUFFER);
+		}
+	}
+}

drivers/usb/host/fhci.h

+/*
+ * Freescale QUICC Engine USB Host Controller Driver
+ *
+ * Copyright (c) Freescale Semicondutor, Inc. 2006.
+ *               Shlomi Gridish <gridish@freescale.com>
+ *               Jerry Huang <Chang-Ming.Huang@freescale.com>
+ * Copyright (c) Logic Product Development, Inc. 2007
+ *               Peter Barada <peterb@logicpd.com>
+ * Copyright (c) MontaVista Software, Inc. 2008.
+ *               Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __FHCI_H
+#define __FHCI_H
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/kfifo.h>
+#include <linux/io.h>
+#include <linux/usb.h>
+#include <asm/qe.h>
+#include "../core/hcd.h"
+
+#define USB_CLOCK	48000000
+
+#define FHCI_PRAM_SIZE 0x100
+
+#define MAX_EDS		32
+#define MAX_TDS		32
+
+
+/* CRC16 field size */
+#define CRC_SIZE 2
+
+/* USB protocol overhead for each frame transmitted from the host */
+#define PROTOCOL_OVERHEAD 7
+
+/* Packet structure, info field */
+#define PKT_PID_DATA0		0x80000000 /* PID - Data toggle zero */
+#define PKT_PID_DATA1		0x40000000 /* PID - Data toggle one  */
+#define PKT_PID_SETUP		0x20000000 /* PID - Setup bit */
+#define PKT_SETUP_STATUS	0x10000000 /* Setup status bit */
+#define PKT_SETADDR_STATUS	0x08000000 /* Set address status bit */
+#define PKT_SET_HOST_LAST	0x04000000 /* Last data packet */
+#define PKT_HOST_DATA		0x02000000 /* Data packet */
+#define PKT_FIRST_IN_FRAME	0x01000000 /* First packet in the frame */
+#define PKT_TOKEN_FRAME		0x00800000 /* Token packet */
+#define PKT_ZLP			0x00400000 /* Zero length packet */
+#define PKT_IN_TOKEN_FRAME	0x00200000 /* IN token packet */
+#define PKT_OUT_TOKEN_FRAME	0x00100000 /* OUT token packet */
+#define PKT_SETUP_TOKEN_FRAME	0x00080000 /* SETUP token packet */
+#define PKT_STALL_FRAME		0x00040000 /* STALL packet */
+#define PKT_NACK_FRAME		0x00020000 /* NACK packet */
+#define PKT_NO_PID		0x00010000 /* No PID */
+#define PKT_NO_CRC		0x00008000 /* don't append CRC */
+#define PKT_HOST_COMMAND	0x00004000 /* Host command packet */
+#define PKT_DUMMY_PACKET	0x00002000 /* Dummy packet, used for mmm */
+#define PKT_LOW_SPEED_PACKET	0x00001000 /* Low-Speed packet */
+
+#define TRANS_OK		(0)
+#define TRANS_INPROGRESS	(-1)
+#define TRANS_DISCARD		(-2)
+#define TRANS_FAIL		(-3)
+
+#define PS_INT		0
+#define PS_DISCONNECTED	1
+#define PS_CONNECTED	2
+#define PS_READY	3
+#define PS_MISSING	4
+
+/* Transfer Descriptor status field */
+#define USB_TD_OK		0x00000000 /* TD transmited or received ok */
+#define USB_TD_INPROGRESS	0x80000000 /* TD is being transmitted */
+#define USB_TD_RX_ER_NONOCT	0x40000000 /* Tx Non Octet Aligned Packet */
+#define USB_TD_RX_ER_BITSTUFF	0x20000000 /* Frame Aborted-Received pkt */
+#define USB_TD_RX_ER_CRC	0x10000000 /* CRC error */
+#define USB_TD_RX_ER_OVERUN	0x08000000 /* Over - run occured */
+#define USB_TD_RX_ER_PID	0x04000000 /* wrong PID received */
+#define USB_TD_RX_DATA_UNDERUN	0x02000000 /* shorter than expected */
+#define USB_TD_RX_DATA_OVERUN	0x01000000 /* longer than expected */
+#define USB_TD_TX_ER_NAK	0x00800000 /* NAK handshake */
+#define USB_TD_TX_ER_STALL	0x00400000 /* STALL handshake */
+#define USB_TD_TX_ER_TIMEOUT	0x00200000 /* transmit time out */
+#define USB_TD_TX_ER_UNDERUN	0x00100000 /* transmit underrun */
+
+#define USB_TD_ERROR (USB_TD_RX_ER_NONOCT | USB_TD_RX_ER_BITSTUFF | \
+		USB_TD_RX_ER_CRC | USB_TD_RX_ER_OVERUN | USB_TD_RX_ER_PID | \
+		USB_TD_RX_DATA_UNDERUN | USB_TD_RX_DATA_OVERUN | \
+		USB_TD_TX_ER_NAK | USB_TD_TX_ER_STALL | \
+		USB_TD_TX_ER_TIMEOUT | USB_TD_TX_ER_UNDERUN)
+
+/* Transfer Descriptor toggle field */
+#define USB_TD_TOGGLE_DATA0	0
+#define USB_TD_TOGGLE_DATA1	1
+#define USB_TD_TOGGLE_CARRY	2
+
+/* #define MULTI_DATA_BUS */
+
+/* Bus mode register RBMR/TBMR */
+#define BUS_MODE_GBL	0x20	/* Global snooping */
+#define BUS_MODE_BO	0x18	/* Byte ordering */
+#define BUS_MODE_BO_BE	0x10	/* Byte ordering - Big-endian */
+#define BUS_MODE_DTB	0x02	/* Data bus */
+
+/* FHCI QE USB Register Description */
+
+/* USB Mode Register bit define */
+#define USB_MODE_EN		0x01
+#define USB_MODE_HOST		0x02
+#define USB_MODE_TEST		0x04
+#define USB_MODE_SFTE		0x08
+#define USB_MODE_RESUME		0x40
+#define USB_MODE_LSS		0x80
+
+/* USB Slave Address Register Mask */
+#define USB_SLVADDR_MASK	0x7F
+
+/* USB Endpoint register define */
+#define USB_EPNUM_MASK		0xF000
+#define USB_EPNUM_SHIFT		12
+
+#define USB_TRANS_MODE_SHIFT	8
+#define USB_TRANS_CTR		0x0000
+#define USB_TRANS_INT		0x0100
+#define USB_TRANS_BULK		0x0200
+#define USB_TRANS_ISO		0x0300
+
+#define USB_EP_MF		0x0020
+#define USB_EP_RTE		0x0010
+
+#define USB_THS_SHIFT		2
+#define USB_THS_MASK		0x000c
+#define USB_THS_NORMAL		0x0
+#define USB_THS_IGNORE_IN	0x0004
+#define USB_THS_NACK		0x0008
+#define USB_THS_STALL		0x000c
+
+#define USB_RHS_SHIFT   	0
+#define USB_RHS_MASK		0x0003
+#define USB_RHS_NORMAL  	0x0
+#define USB_RHS_IGNORE_OUT	0x0001
+#define USB_RHS_NACK		0x0002
+#define USB_RHS_STALL		0x0003
+
+#define USB_RTHS_MASK		0x000f
+
+/* USB Command Register define */
+#define USB_CMD_STR_FIFO	0x80
+#define USB_CMD_FLUSH_FIFO	0x40
+#define USB_CMD_ISFT		0x20
+#define USB_CMD_DSFT		0x10
+#define USB_CMD_EP_MASK		0x03
+
+/* USB Event and Mask Register define */
+#define USB_E_MSF_MASK		0x0800
+#define USB_E_SFT_MASK		0x0400
+#define USB_E_RESET_MASK	0x0200
+#define USB_E_IDLE_MASK		0x0100
+#define USB_E_TXE4_MASK		0x0080
+#define USB_E_TXE3_MASK		0x0040
+#define USB_E_TXE2_MASK		0x0020
+#define USB_E_TXE1_MASK		0x0010
+#define USB_E_SOF_MASK		0x0008
+#define USB_E_BSY_MASK		0x0004
+#define USB_E_TXB_MASK		0x0002
+#define USB_E_RXB_MASK		0x0001
+
+/* Freescale USB Host controller registers */
+struct fhci_regs {
+	u8 usb_mod;		/* mode register */
+	u8 usb_addr;		/* address register */
+	u8 usb_comm;		/* command register */
+	u8 reserved1[1];
+	__be16 usb_ep[4];	/* endpoint register */
+	u8 reserved2[4];
+	__be16 usb_event;	/* event register */
+	u8 reserved3[2];
+	__be16 usb_mask;	/* mask register */
+	u8 reserved4[1];
+	u8 usb_status;		/* status register */
+	__be16 usb_sof_tmr;	/* Start Of Frame timer */
+	u8 reserved5[2];
+	__be16 usb_frame_num;	/* frame number register */
+	u8 reserved6[1];
+};
+
+/* Freescale USB HOST */
+struct fhci_pram {
+	__be16 ep_ptr[4];	/* Endpoint porter reg */
+	__be32 rx_state;	/* Rx internal state */
+	__be32 rx_ptr;		/* Rx internal data pointer */
+	__be16 frame_num;	/* Frame number */
+	__be16 rx_cnt;		/* Rx byte count */
+	__be32 rx_temp;		/* Rx temp */
+	__be32 rx_data_temp;	/* Rx data temp */
+	__be16 rx_u_ptr;	/* Rx microcode return address temp */
+	u8 reserved1[2];	/* reserved area */
+	__be32 sof_tbl;		/* SOF lookup table pointer */
+	u8 sof_u_crc_temp;	/* SOF micorcode CRC5 temp reg */
+	u8 reserved2[0xdb];
+};
+
+/* Freescale USB Endpoint*/
+struct fhci_ep_pram {
+	__be16 rx_base;		/* Rx BD base address */
+	__be16 tx_base;		/* Tx BD base address */
+	u8 rx_func_code;	/* Rx function code */
+	u8 tx_func_code;	/* Tx function code */
+	__be16 rx_buff_len;	/* Rx buffer length */
+	__be16 rx_bd_ptr;	/* Rx BD pointer */
+	__be16 tx_bd_ptr;	/* Tx BD pointer */
+	__be32 tx_state;	/* Tx internal state */
+	__be32 tx_ptr;		/* Tx internal data pointer */
+	__be16 tx_crc;		/* temp transmit CRC */
+	__be16 tx_cnt;		/* Tx byte count */
+	__be32 tx_temp;		/* Tx temp */
+	__be16 tx_u_ptr;	/* Tx microcode return address temp */
+	__be16 reserved;
+};
+
+struct fhci_controller_list {
+	struct list_head ctrl_list;	/* control endpoints */
+	struct list_head bulk_list;	/* bulk endpoints */
+	struct list_head iso_list;	/* isochronous endpoints */
+	struct list_head intr_list;	/* interruput endpoints */
+	struct list_head done_list;	/* done transfers */
+};
+
+struct virtual_root_hub {
+	int dev_num;	/* USB address of the root hub */
+	u32 feature;	/* indicates what feature has been set */
+	struct usb_hub_status hub;
+	struct usb_port_status port;
+};
+
+enum fhci_gpios {
+	GPIO_USBOE = 0,
+	GPIO_USBTP,
+	GPIO_USBTN,
+	GPIO_USBRP,
+	GPIO_USBRN,
+	/* these are optional */
+	GPIO_SPEED,
+	GPIO_POWER,
+	NUM_GPIOS,
+};
+
+enum fhci_pins {
+	PIN_USBOE = 0,
+	PIN_USBTP,
+	PIN_USBTN,
+	NUM_PINS,
+};
+
+struct fhci_hcd {
+	enum qe_clock fullspeed_clk;
+	enum qe_clock lowspeed_clk;
+	struct qe_pin *pins[NUM_PINS];
+	int gpios[NUM_GPIOS];
+	bool alow_gpios[NUM_GPIOS];
+
+	struct fhci_regs __iomem *regs;	/* I/O memory used to communicate */
+	struct fhci_pram __iomem *pram;	/* Parameter RAM */
+	struct gtm_timer *timer;
+
+	spinlock_t lock;
+	struct fhci_usb *usb_lld; /* Low-level driver */
+	struct virtual_root_hub *vroot_hub; /* the virtual root hub */
+	int active_urbs;
+	struct fhci_controller_list *hc_list;
+	struct tasklet_struct *process_done_task; /* tasklet for done list */
+
+	struct list_head empty_eds;
+	struct list_head empty_tds;
+
+#ifdef CONFIG_FHCI_DEBUG
+	int usb_irq_stat[13];
+	struct dentry *dfs_root;
+	struct dentry *dfs_regs;
+	struct dentry *dfs_irq_stat;
+#endif
+};
+
+#define USB_FRAME_USAGE 90
+#define FRAME_TIME_USAGE (USB_FRAME_USAGE*10)	/* frame time usage */
+#define SW_FIX_TIME_BETWEEN_TRANSACTION 150	/* SW */
+#define MAX_BYTES_PER_FRAME (USB_FRAME_USAGE*15)
+#define MAX_PERIODIC_FRAME_USAGE 90
+
+/* transaction type */
+enum fhci_ta_type {
+	FHCI_TA_IN = 0,	/* input transaction */
+	FHCI_TA_OUT,	/* output transaction */
+	FHCI_TA_SETUP,	/* setup transaction */
+};
+
+/* transfer mode */
+enum fhci_tf_mode {
+	FHCI_TF_CTRL = 0,
+	FHCI_TF_ISO,
+	FHCI_TF_BULK,
+	FHCI_TF_INTR,
+};
+
+enum fhci_speed {
+	FHCI_FULL_SPEED,
+	FHCI_LOW_SPEED,
+};
+
+/* endpoint state */
+enum fhci_ed_state {
+	FHCI_ED_NEW = 0, /* pipe is new */
+	FHCI_ED_OPER,    /* pipe is operating */
+	FHCI_ED_URB_DEL, /* pipe is in hold because urb is being deleted */
+	FHCI_ED_SKIP,    /* skip this pipe */
+	FHCI_ED_HALTED,  /* pipe is halted */
+};
+
+enum fhci_port_status {
+	FHCI_PORT_POWER_OFF = 0,
+	FHCI_PORT_DISABLED,
+	FHCI_PORT_DISCONNECTING,
+	FHCI_PORT_WAITING,	/* waiting for connection */
+	FHCI_PORT_FULL,		/* full speed connected */
+	FHCI_PORT_LOW,		/* low speed connected */
+};
+
+enum fhci_mem_alloc {
+	MEM_CACHABLE_SYS = 0x00000001,	/* primary DDR,cachable */
+	MEM_NOCACHE_SYS = 0x00000004,	/* primary DDR,non-cachable */
+	MEM_SECONDARY = 0x00000002,	/* either secondary DDR or SDRAM */
+	MEM_PRAM = 0x00000008,		/* multi-user RAM identifier */
+};
+
+/* USB default parameters*/
+#define DEFAULT_RING_LEN	8
+#define DEFAULT_DATA_MEM	MEM_CACHABLE_SYS
+
+struct ed {
+	u8 dev_addr;		/* device address */
+	u8 ep_addr;		/* endpoint address */
+	enum fhci_tf_mode mode;	/* USB transfer mode */
+	enum fhci_speed speed;
+	unsigned int max_pkt_size;
+	enum fhci_ed_state state;
+	struct list_head td_list; /* a list of all queued TD to this pipe */
+	struct list_head node;
+
+	/* read only parameters, should be cleared upon initialization */
+	u8 toggle_carry;	/* toggle carry from the last TD submitted */
+	u32 last_iso;		/* time stamp of last queued ISO transfer */
+	struct td *td_head;	/* a pointer to the current TD handled */
+};
+
+struct td {
+	void *data;		 /* a pointer to the data buffer */
+	unsigned int len;	 /* length of the data to be submitted */
+	unsigned int actual_len; /* actual bytes transfered on this td */
+	enum fhci_ta_type type;	 /* transaction type */
+	u8 toggle;		 /* toggle for next trans. within this TD */
+	u16 iso_index;		 /* ISO transaction index */
+	u16 start_frame;	 /* start frame time stamp */
+	u16 interval;		 /* interval between trans. (for ISO/Intr) */
+	u32 status;		 /* status of the TD */
+	struct ed *ed;		 /* a handle to the corresponding ED */
+	struct urb *urb;	 /* a handle to the corresponding URB */
+	bool ioc;		 /* Inform On Completion */
+	struct list_head node;
+
+	/* read only parameters should be cleared upon initialization */
+	struct packet *pkt;
+	int nak_cnt;
+	int error_cnt;
+	struct list_head frame_lh;
+};
+
+struct packet {
+	u8 *data;	/* packet data */
+	u32 len;	/* packet length */
+	u32 status;	/* status of the packet - equivalent to the status
+			 * field for the corresponding structure td */
+	u32 info;	/* packet information */
+	void __iomem *priv_data; /* private data of the driver (TDs or BDs) */
+};
+
+/* struct for each URB */
+#define URB_INPROGRESS	0
+#define URB_DEL		1
+
+/* URB states (state field) */
+#define US_BULK		0
+#define US_BULK0	1
+
+/* three setup states */
+#define US_CTRL_SETUP	2
+#define US_CTRL_DATA	1
+#define US_CTRL_ACK	0
+
+#define EP_ZERO	0
+
+struct urb_priv {
+	int num_of_tds;
+	int tds_cnt;
+	int state;
+
+	struct td **tds;
+	struct ed *ed;
+	struct timer_list time_out;
+};
+
+struct endpoint {
+	/* Pointer to ep parameter RAM */
+	struct fhci_ep_pram __iomem *ep_pram_ptr;
+
+	/* Host transactions */
+	struct usb_td __iomem *td_base; /* first TD in the ring */
+	struct usb_td __iomem *conf_td; /* next TD for confirm after transac */
+	struct usb_td __iomem *empty_td;/* next TD for new transaction req. */
+	struct kfifo *empty_frame_Q;  /* Empty frames list to use */
+	struct kfifo *conf_frame_Q;   /* frames passed to TDs,waiting for tx */
+	struct kfifo *dummy_packets_Q;/* dummy packets for the CRC overun */
+
+	bool already_pushed_dummy_bd;
+};
+
+/* struct for each 1mSec frame time */
+#define FRAME_IS_TRANSMITTED		0x00
+#define FRAME_TIMER_END_TRANSMISSION	0x01
+#define FRAME_DATA_END_TRANSMISSION	0x02
+#define FRAME_END_TRANSMISSION		0x03
+#define FRAME_IS_PREPARED		0x04
+
+struct fhci_time_frame {
+	u16 frame_num;	 /* frame number */
+	u16 total_bytes; /* total bytes submitted within this frame */
+	u8 frame_status; /* flag that indicates to stop fill this frame */
+	struct list_head tds_list; /* all tds of this frame */
+};
+
+/* internal driver structure*/
+struct fhci_usb {
+	u16 saved_msk;		 /* saving of the USB mask register */
+	struct endpoint *ep0;	 /* pointer for endpoint0 structure */
+	int intr_nesting_cnt;	 /* interrupt nesting counter */
+	u16 max_frame_usage;	 /* max frame time usage,in micro-sec */
+	u16 max_bytes_per_frame; /* max byte can be tx in one time frame */
+	u32 sw_transaction_time; /* sw complete trans time,in micro-sec */
+	struct fhci_time_frame *actual_frame;
+	struct fhci_controller_list *hc_list;	/* main structure for hc */
+	struct virtual_root_hub *vroot_hub;
+	enum fhci_port_status port_status;	/* v_rh port status */
+
+	u32 (*transfer_confirm)(struct fhci_hcd *fhci);
+
+	struct fhci_hcd *fhci;
+};
+
+/*
+ * Various helpers and prototypes below.
+ */
+
+static inline u16 get_frame_num(struct fhci_hcd *fhci)
+{
+	return in_be16(&fhci->pram->frame_num) & 0x07ff;
+}
+
+#define fhci_dbg(fhci, fmt, args...) \
+		dev_dbg(fhci_to_hcd(fhci)->self.controller, fmt, ##args)
+#define fhci_vdbg(fhci, fmt, args...) \
+		dev_vdbg(fhci_to_hcd(fhci)->self.controller, fmt, ##args)
+#define fhci_err(fhci, fmt, args...) \
+		dev_err(fhci_to_hcd(fhci)->self.controller, fmt, ##args)
+#define fhci_info(fhci, fmt, args...) \
+		dev_info(fhci_to_hcd(fhci)->self.controller, fmt, ##args)
+#define fhci_warn(fhci, fmt, args...) \
+		dev_warn(fhci_to_hcd(fhci)->self.controller, fmt, ##args)
+
+static inline struct fhci_hcd *hcd_to_fhci(struct usb_hcd *hcd)
+{
+	return (struct fhci_hcd *)hcd->hcd_priv;
+}
+
+static inline struct usb_hcd *fhci_to_hcd(struct fhci_hcd *fhci)
+{
+	return container_of((void *)fhci, struct usb_hcd, hcd_priv);
+}
+
+/* fifo of pointers */
+static inline struct kfifo *cq_new(int size)
+{
+	return kfifo_alloc(size * sizeof(void *), GFP_KERNEL, NULL);
+}
+
+static inline void cq_delete(struct kfifo *kfifo)
+{
+	kfifo_free(kfifo);
+}
+
+static inline unsigned int cq_howmany(struct kfifo *kfifo)
+{
+	return __kfifo_len(kfifo) / sizeof(void *);
+}
+
+static inline int cq_put(struct kfifo *kfifo, void *p)
+{
+	return __kfifo_put(kfifo, (void *)&p, sizeof(p));
+}
+
+static inline void *cq_get(struct kfifo *kfifo)
+{
+	void *p = NULL;
+
+	__kfifo_get(kfifo, (void *)&p, sizeof(p));
+	return p;
+}
+
+/* fhci-hcd.c */
+void fhci_start_sof_timer(struct fhci_hcd *fhci);
+void fhci_stop_sof_timer(struct fhci_hcd *fhci);
+u16 fhci_get_sof_timer_count(struct fhci_usb *usb);
+void fhci_usb_enable_interrupt(struct fhci_usb *usb);
+void fhci_usb_disable_interrupt(struct fhci_usb *usb);
+int fhci_ioports_check_bus_state(struct fhci_hcd *fhci);
+
+/* fhci-mem.c */
+void fhci_recycle_empty_td(struct fhci_hcd *fhci, struct td *td);
+void fhci_recycle_empty_ed(struct fhci_hcd *fhci, struct ed *ed);
+struct ed *fhci_get_empty_ed(struct fhci_hcd *fhci);
+struct td *fhci_td_fill(struct fhci_hcd *fhci, struct urb *urb,
+			struct urb_priv *urb_priv, struct ed *ed, u16 index,
+			enum fhci_ta_type type, int toggle, u8 *data, u32 len,
+			u16 interval, u16 start_frame, bool ioc);
+void fhci_add_tds_to_ed(struct ed *ed, struct td **td_list, int number);
+
+/* fhci-hub.c */
+void fhci_config_transceiver(struct fhci_hcd *fhci,
+			enum fhci_port_status status);
+void fhci_port_disable(struct fhci_hcd *fhci);
+void fhci_port_enable(void *lld);
+void fhci_io_port_generate_reset(struct fhci_hcd *fhci);
+void fhci_port_reset(void *lld);
+int fhci_hub_status_data(struct usb_hcd *hcd, char *buf);
+int fhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
+		     u16 wIndex, char *buf, u16 wLength);
+
+/* fhci-tds.c */
+void fhci_flush_bds(struct fhci_usb *usb);
+void fhci_flush_actual_frame(struct fhci_usb *usb);
+u32 fhci_host_transaction(struct fhci_usb *usb, struct packet *pkt,
+			  enum fhci_ta_type trans_type, u8 dest_addr,
+			  u8 dest_ep, enum fhci_tf_mode trans_mode,
+			  enum fhci_speed dest_speed, u8 data_toggle);
+void fhci_host_transmit_actual_frame(struct fhci_usb *usb);
+void fhci_tx_conf_interrupt(struct fhci_usb *usb);
+void fhci_push_dummy_bd(struct endpoint *ep);
+u32 fhci_create_ep(struct fhci_usb *usb, enum fhci_mem_alloc data_mem,
+		   u32 ring_len);
+void fhci_init_ep_registers(struct fhci_usb *usb,
+			    struct endpoint *ep,
+			    enum fhci_mem_alloc data_mem);
+void fhci_ep0_free(struct fhci_usb *usb);
+
+/* fhci-sched.c */
+extern struct tasklet_struct fhci_tasklet;
+void fhci_transaction_confirm(struct fhci_usb *usb, struct packet *pkt);
+void fhci_flush_all_transmissions(struct fhci_usb *usb);
+void fhci_schedule_transactions(struct fhci_usb *usb);
+void fhci_device_connected_interrupt(struct fhci_hcd *fhci);
+void fhci_device_disconnected_interrupt(struct fhci_hcd *fhci);
+void fhci_queue_urb(struct fhci_hcd *fhci, struct urb *urb);
+u32 fhci_transfer_confirm_callback(struct fhci_hcd *fhci);
+irqreturn_t fhci_irq(struct usb_hcd *hcd);
+irqreturn_t fhci_frame_limit_timer_irq(int irq, void *_hcd);
+
+/* fhci-q.h */
+void fhci_urb_complete_free(struct fhci_hcd *fhci, struct urb *urb);
+struct td *fhci_remove_td_from_ed(struct ed *ed);
+struct td *fhci_remove_td_from_frame(struct fhci_time_frame *frame);
+void fhci_move_td_from_ed_to_done_list(struct fhci_usb *usb, struct ed *ed);
+struct td *fhci_peek_td_from_frame(struct fhci_time_frame *frame);
+void fhci_add_td_to_frame(struct fhci_time_frame *frame, struct td *td);
+struct td *fhci_remove_td_from_done_list(struct fhci_controller_list *p_list);
+void fhci_done_td(struct urb *urb, struct td *td);
+void fhci_del_ed_list(struct fhci_hcd *fhci, struct ed *ed);
+
+#ifdef CONFIG_FHCI_DEBUG
+
+void fhci_dbg_isr(struct fhci_hcd *fhci, int usb_er);
+void fhci_dfs_destroy(struct fhci_hcd *fhci);
+void fhci_dfs_create(struct fhci_hcd *fhci);
+
+#else
+
+static inline void fhci_dbg_isr(struct fhci_hcd *fhci, int usb_er) {}
+static inline void fhci_dfs_destroy(struct fhci_hcd *fhci) {}
+static inline void fhci_dfs_create(struct fhci_hcd *fhci) {}
+
+#endif /* CONFIG_FHCI_DEBUG */
+
+#endif /* __FHCI_H */