Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
提交 1c0daab7 编写于 作者: A Alexander Shiyan 提交者： Shawn Guo
浏览文件
操作

ARM: dts: imx51-babbage: Sort nodes by name 

This patch sorts nodes by name and moves "iomux" configuration at
the bottom of file.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>
上级 db8235ec
无相关合并请求
隐藏空白更改
内联 并排
Showing with 133 addition and 133 deletion
arch/arm/boot/dts/imx51-babbage.dts
浏览文件 @ 1c0daab7
......@@ -21,6 +21,20 @@
reg = <0x90000000 0x20000000>;
};
clocks {
ckih1 {
clock-frequency = <22579200>;
};
clk_26M: codec_clock {
compatible = "fixed-clock";
reg=<0>;
#clock-cells = <0>;
clock-frequency = <26000000>;
gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
};
};
display0: display@di0 {
compatible = "fsl,imx-parallel-display";
interface-pix-fmt = "rgb24";
......@@ -104,34 +118,6 @@
};
};
sound {
compatible = "fsl,imx51-babbage-sgtl5000",
"fsl,imx-audio-sgtl5000";
model = "imx51-babbage-sgtl5000";
ssi-controller = <&ssi2>;
audio-codec = <&sgtl5000>;
audio-routing =
"MIC_IN", "Mic Jack",
"Mic Jack", "Mic Bias",
"Headphone Jack", "HP_OUT";
mux-int-port = <2>;
mux-ext-port = <3>;
};
clocks {
ckih1 {
clock-frequency = <22579200>;
};
clk_26M: codec_clock {
compatible = "fixed-clock";
reg=<0>;
#clock-cells = <0>;
clock-frequency = <26000000>;
gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
};
};
regulators {
compatible = "simple-bus";
#address-cells = <1>;
......@@ -162,6 +148,20 @@
};
};
sound {
compatible = "fsl,imx51-babbage-sgtl5000",
"fsl,imx-audio-sgtl5000";
model = "imx51-babbage-sgtl5000";
ssi-controller = <&ssi2>;
audio-codec = <&sgtl5000>;
audio-routing =
"MIC_IN", "Mic Jack",
"Mic Jack", "Mic Bias",
"Headphone Jack", "HP_OUT";
mux-int-port = <2>;
mux-ext-port = <3>;
};
usbphy {
#address-cells = <1>;
#size-cells = <0>;
......@@ -176,26 +176,9 @@
};
};
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>;
fsl,cd-controller;
fsl,wp-controller;
status = "okay";
};
&esdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc2>;
cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&uart3 {
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
fsl,uart-has-rtscts;
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
};
......@@ -327,6 +310,47 @@
};
};
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>;
fsl,cd-controller;
fsl,wp-controller;
status = "okay";
};
&esdhc2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc2>;
cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
phy-reset-duration = <1>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_clkcodec>;
reg = <0x0a>;
clocks = <&clk_26M>;
VDDA-supply = <&vdig_reg>;
VDDIO-supply = <&vvideo_reg>;
};
};
&ipu_di0_disp0 {
remote-endpoint = <&display0_in>;
};
......@@ -335,11 +359,72 @@
remote-endpoint = <&display1_in>;
};
&kpp {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_kpp>;
linux,keymap = <
MATRIX_KEY(0, 0, KEY_UP)
MATRIX_KEY(0, 1, KEY_DOWN)
MATRIX_KEY(0, 2, KEY_VOLUMEDOWN)
MATRIX_KEY(0, 3, KEY_HOME)
MATRIX_KEY(1, 0, KEY_RIGHT)
MATRIX_KEY(1, 1, KEY_LEFT)
MATRIX_KEY(1, 2, KEY_ENTER)
MATRIX_KEY(1, 3, KEY_VOLUMEUP)
MATRIX_KEY(2, 0, KEY_F6)
MATRIX_KEY(2, 1, KEY_F8)
MATRIX_KEY(2, 2, KEY_F9)
MATRIX_KEY(2, 3, KEY_F10)
MATRIX_KEY(3, 0, KEY_F1)
MATRIX_KEY(3, 1, KEY_F2)
MATRIX_KEY(3, 2, KEY_F3)
MATRIX_KEY(3, 3, KEY_POWER)
>;
status = "okay";
};
&ssi2 {
fsl,mode = "i2s-slave";
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
fsl,uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
fsl,uart-has-rtscts;
status = "okay";
};
&usbh1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1>;
vbus-supply = <&reg_usbh1_vbus>;
fsl,usbphy = <&usbh1phy>;
phy_type = "ulpi";
status = "okay";
};
&usbotg {
dr_mode = "otg";
disable-over-current;
phy_type = "utmi_wide";
vbus-supply = <&reg_usbotg_vbus>;
status = "okay";
};
&iomuxc {
imx51-babbage {
pinctrl_audmux: audmuxgrp {
......@@ -412,7 +497,7 @@
MX51_PAD_NANDF_CS6__FEC_TDATA3 0x80000000
MX51_PAD_NANDF_CS7__FEC_TX_EN 0x80000000
MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK 0x80000000
MX51_PAD_EIM_A20__GPIO2_14 0x85 /* Reset */
MX51_PAD_EIM_A20__GPIO2_14 0x85 /* Reset */
>;
};
......@@ -564,88 +649,3 @@
};
};
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
fsl,uart-has-rtscts;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
sgtl5000: codec@0a {
compatible = "fsl,sgtl5000";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_clkcodec>;
reg = <0x0a>;
clocks = <&clk_26M>;
VDDA-supply = <&vdig_reg>;
VDDIO-supply = <&vvideo_reg>;
};
};
&audmux {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_audmux>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
phy-reset-duration = <1>;
status = "okay";
};
&kpp {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_kpp>;
linux,keymap = <
MATRIX_KEY(0, 0, KEY_UP)
MATRIX_KEY(0, 1, KEY_DOWN)
MATRIX_KEY(0, 2, KEY_VOLUMEDOWN)
MATRIX_KEY(0, 3, KEY_HOME)
MATRIX_KEY(1, 0, KEY_RIGHT)
MATRIX_KEY(1, 1, KEY_LEFT)
MATRIX_KEY(1, 2, KEY_ENTER)
MATRIX_KEY(1, 3, KEY_VOLUMEUP)
MATRIX_KEY(2, 0, KEY_F6)
MATRIX_KEY(2, 1, KEY_F8)
MATRIX_KEY(2, 2, KEY_F9)
MATRIX_KEY(2, 3, KEY_F10)
MATRIX_KEY(3, 0, KEY_F1)
MATRIX_KEY(3, 1, KEY_F2)
MATRIX_KEY(3, 2, KEY_F3)
MATRIX_KEY(3, 3, KEY_POWER)
>;
status = "okay";
};
&usbh1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh1>;
vbus-supply = <&reg_usbh1_vbus>;
fsl,usbphy = <&usbh1phy>;
phy_type = "ulpi";
status = "okay";
};
&usbotg {
dr_mode = "otg";
disable-over-current;
phy_type = "utmi_wide";
vbus-supply = <&reg_usbotg_vbus>;
status = "okay";
};
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或
反馈
建议 客服 返回
顶部