ixgbe: Adding 100MB FULL support in ethtool

Current driver does not show 100MB support in ethtool.
Adding support for the same.
Signed-off-by: NAtita Shirwaikar <atita.shirwaikar@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/ixgbe/ixgbe_ethtool.c

@@ -152,7 +152,17 @@ static int ixgbe_get_settings(struct net_device *netdev,
 		ecmd->supported |= (SUPPORTED_1000baseT_Full |
 		                    SUPPORTED_Autoneg);
 
+		switch (hw->mac.type) {
+		case ixgbe_mac_X540:
+			ecmd->supported |= SUPPORTED_100baseT_Full;
+			break;
+		default:
+			break;
+		}
+
 		ecmd->advertising = ADVERTISED_Autoneg;
+		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL)
+			ecmd->advertising |= ADVERTISED_100baseT_Full;
 		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10GB_FULL)
 			ecmd->advertising |= ADVERTISED_10000baseT_Full;
 		if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL)
@@ -167,6 +177,15 @@ static int ixgbe_get_settings(struct net_device *netdev,
 			ecmd->advertising |= (ADVERTISED_10000baseT_Full |
 					      ADVERTISED_1000baseT_Full);
 
+		switch (hw->mac.type) {
+		case ixgbe_mac_X540:
+			if (!(ecmd->advertising & ADVERTISED_100baseT_Full))
+				ecmd->advertising |= (ADVERTISED_100baseT_Full);
+			break;
+		default:
+			break;
+		}
+
 		if (hw->phy.media_type == ixgbe_media_type_copper) {
 			ecmd->supported |= SUPPORTED_TP;
 			ecmd->advertising |= ADVERTISED_TP;
@@ -271,8 +290,19 @@ static int ixgbe_get_settings(struct net_device *netdev,
 
 	hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
 	if (link_up) {
-		ecmd->speed = (link_speed == IXGBE_LINK_SPEED_10GB_FULL) ?
-		               SPEED_10000 : SPEED_1000;
+		switch (link_speed) {
+		case IXGBE_LINK_SPEED_10GB_FULL:
+			ecmd->speed = SPEED_10000;
+			break;
+		case IXGBE_LINK_SPEED_1GB_FULL:
+			ecmd->speed = SPEED_1000;
+			break;
+		case IXGBE_LINK_SPEED_100_FULL:
+			ecmd->speed = SPEED_100;
+			break;
+		default:
+			break;
+		}
 		ecmd->duplex = DUPLEX_FULL;
 	} else {
 		ecmd->speed = -1;

drivers/net/ixgbe/ixgbe_main.c

@@ -6102,7 +6102,10 @@ static void ixgbe_watchdog_task(struct work_struct *work)
 			       (link_speed == IXGBE_LINK_SPEED_10GB_FULL ?
 			       "10 Gbps" :
 			       (link_speed == IXGBE_LINK_SPEED_1GB_FULL ?
-			       "1 Gbps" : "unknown speed")),
+			       "1 Gbps" :
+			       (link_speed == IXGBE_LINK_SPEED_100_FULL ?
+			       "100 Mbps" :
+			       "unknown speed"))),
 			       ((flow_rx && flow_tx) ? "RX/TX" :
 			       (flow_rx ? "RX" :
 			       (flow_tx ? "TX" : "None"))));