Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
提交 11b64d31 编写于 作者: M Maxim Levitsky 提交者： Mauro Carvalho Chehab
浏览文件
操作

[media] IR: ene_ir: updates 

* Add support for newer firmware version that uses different
buffer format. Makes hardware work for many users.

* Register name updates

* Lot of refactoring

* Lots of fixes as a result of full testing

* Idle mode is done now by resetting the device, and this eliminates
the ugly sample_period = 75 hack.

Every feature of the driver is now well tested.
Signed-off-by: NMaxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
上级 991369e3
展开全部 隐藏空白更改
内联 并排
Showing with 719 addition and 538 deletion
drivers/media/IR/Kconfig
浏览文件 @ 11b64d31
......@@ -102,15 +102,15 @@ config IR_LIRC_CODEC
the LIRC interface.
config IR_ENE
tristate "ENE eHome Receiver/Transciever (pnp id: ENE0100/ENE02xxx)"
tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
depends on PNP
depends on IR_CORE
---help---
Say Y here to enable support for integrated infrared receiver
/transciever made by ENE.
/transceiver made by ENE.
You can see if you have it by looking at lspnp output.
Output should include ENE0100 ENE0200 or something similiar.
Output should include ENE0100 ENE0200 or something similar.
To compile this driver as a module, choose M here: the
module will be called ene_ir.
......
drivers/media/IR/ene_ir.c
浏览文件 @ 11b64d31
此差异已折叠。
drivers/media/IR/ene_ir.h
浏览文件 @ 11b64d31
/*
* driver for ENE KB3926 B/C/D CIR (also known as ENE0XXX)
* driver for ENE KB3926 B/C/D/E/F CIR (also known as ENE0XXX)
*
* Copyright (C) 2010 Maxim Levitsky <maximlevitsky@gmail.com>
*
......@@ -26,43 +26,50 @@
#define ENE_ADDR_HI 1 /* hi byte of register address */
#define ENE_ADDR_LO 2 /* low byte of register address */
#define ENE_IO 3 /* read/write window */
#define ENE_MAX_IO 4
/* 8 bytes of samples, divided in 2 halfs*/
#define ENE_SAMPLE_BUFFER 0xF8F0 /* regular sample buffer */
#define ENE_SAMPLE_SPC_MASK 0x80 /* sample is space */
#define ENE_SAMPLE_VALUE_MASK 0x7F
#define ENE_SAMPLE_OVERFLOW 0x7F
#define ENE_SAMPLES_SIZE 4
/* fan input sample buffer */
#define ENE_SAMPLE_BUFFER_FAN 0xF8FB /* this buffer holds high byte of */
/* each sample of normal buffer */
#define ENE_FAN_SMPL_PULS_MSK 0x8000 /* this bit of combined sample */
/* if set, says that sample is pulse */
#define ENE_FAN_VALUE_MASK 0x0FFF /* mask for valid bits of the value */
/* first firmware register */
#define ENE_FW1 0xF8F8
#define ENE_IO_SIZE 4
/* 8 bytes of samples, divided in 2 packets*/
#define ENE_FW_SAMPLE_BUFFER 0xF8F0 /* sample buffer */
#define ENE_FW_SAMPLE_SPACE 0x80 /* sample is space */
#define ENE_FW_PACKET_SIZE 4
/* first firmware flag register */
#define ENE_FW1 0xF8F8 /* flagr */
#define ENE_FW1_ENABLE 0x01 /* enable fw processing */
#define ENE_FW1_TXIRQ 0x02 /* TX interrupt pending */
#define ENE_FW1_HAS_EXTRA_BUF 0x04 /* fw uses extra buffer*/
#define ENE_FW1_EXTRA_BUF_HND 0x08 /* extra buffer handshake bit*/
#define ENE_FW1_LED_ON 0x10 /* turn on a led */
#define ENE_FW1_WPATTERN 0x20 /* enable wake pattern */
#define ENE_FW1_WAKE 0x40 /* enable wake from S3 */
#define ENE_FW1_IRQ 0x80 /* enable interrupt */
/* second firmware register */
#define ENE_FW2 0xF8F9
#define ENE_FW2_BUF_HIGH 0x01 /* which half of the buffer to read */
#define ENE_FW2_IRQ_CLR 0x04 /* clear this on IRQ */
#define ENE_FW2_GP40_AS_LEARN 0x08 /* normal input is used as */
/* learning input */
#define ENE_FW2_FAN_AS_NRML_IN 0x40 /* fan is used as normal input */
/* second firmware flag register */
#define ENE_FW2 0xF8F9 /* flagw */
#define ENE_FW2_BUF_WPTR 0x01 /* which half of the buffer to read */
#define ENE_FW2_RXIRQ 0x04 /* RX IRQ pending*/
#define ENE_FW2_GP0A 0x08 /* Use GPIO0A for demodulated input */
#define ENE_FW2_EMMITER1_CONN 0x10 /* TX emmiter 1 connected */
#define ENE_FW2_EMMITER2_CONN 0x20 /* TX emmiter 2 connected */
#define ENE_FW2_FAN_INPUT 0x40 /* fan input used for demodulated data*/
#define ENE_FW2_LEARNING 0x80 /* hardware supports learning and TX */
/* firmware RX pointer for new style buffer */
#define ENE_FW_RX_POINTER 0xF8FA
/* high parts of samples for fan input (8 samples)*/
#define ENE_FW_SMPL_BUF_FAN 0xF8FB
#define ENE_FW_SMPL_BUF_FAN_PLS 0x8000 /* combined sample is pulse */
#define ENE_FW_SMPL_BUF_FAN_MSK 0x0FFF /* combined sample maximum value */
#define ENE_FW_SAMPLE_PERIOD_FAN 61 /* fan input has fixed sample period */
/* transmitter ports */
#define ENE_TX_PORT2 0xFC01 /* this enables one or both */
#define ENE_TX_PORT2_EN 0x20 /* TX ports */
#define ENE_TX_PORT1 0xFC08
#define ENE_TX_PORT1_EN 0x02
#define ENE_GPIOFS1 0xFC01
#define ENE_GPIOFS1_GPIO0D 0x20 /* enable tx output on GPIO0D */
#define ENE_GPIOFS8 0xFC08
#define ENE_GPIOFS8_GPIO41 0x02 /* enable tx output on GPIO40 */
/* IRQ registers block (for revision B) */
#define ENEB_IRQ 0xFD09 /* IRQ number */
......@@ -70,97 +77,99 @@
#define ENEB_IRQ_STATUS 0xFD80 /* irq status */
#define ENEB_IRQ_STATUS_IR 0x20 /* IR irq */
/* fan as input settings - only if learning capable */
/* fan as input settings */
#define ENE_FAN_AS_IN1 0xFE30 /* fan init reg 1 */
#define ENE_FAN_AS_IN1_EN 0xCD
#define ENE_FAN_AS_IN2 0xFE31 /* fan init reg 2 */
#define ENE_FAN_AS_IN2_EN 0x03
#define ENE_SAMPLE_PERIOD_FAN 61 /* fan input has fixed sample period */
/* IRQ registers block (for revision C,D) */
#define ENEC_IRQ 0xFE9B /* new irq settings register */
#define ENEC_IRQ_MASK 0x0F /* irq number mask */
#define ENEC_IRQ_UNK_EN 0x10 /* always enabled */
#define ENEC_IRQ_STATUS 0x20 /* irq status and ACK */
/* CIR block settings */
#define ENE_CIR_CONF1 0xFEC0
#define ENE_CIR_CONF1_TX_CLEAR 0x01 /* clear that on revC */
/* while transmitting */
#define ENE_CIR_CONF1_RX_ON 0x07 /* normal receiver enabled */
#define ENE_CIR_CONF1_LEARN1 0x08 /* enabled on learning mode */
#define ENE_CIR_CONF1_TX_ON 0x30 /* enabled on transmit */
#define ENE_CIR_CONF1_TX_CARR 0x80 /* send TX carrier or not */
#define ENE_CIR_CONF2 0xFEC1 /* unknown setting = 0 */
#define ENE_CIR_CONF2_LEARN2 0x10 /* set on enable learning */
#define ENE_CIR_CONF2_GPIO40DIS 0x20 /* disable input via gpio40 */
#define ENE_CIR_SAMPLE_PERIOD 0xFEC8 /* sample period in us */
#define ENE_CIR_SAMPLE_OVERFLOW 0x80 /* interrupt on overflows if set */
/* Two byte tx buffer */
#define ENE_TX_INPUT1 0xFEC9
#define ENE_TX_INPUT2 0xFECA
#define ENE_TX_PULSE_MASK 0x80 /* Transmitted sample is pulse */
#define ENE_TX_SMLP_MASK 0x7F
#define ENE_TX_SMPL_PERIOD 50 /* transmit sample period - fixed */
#define ENE_IRQ 0xFE9B /* new irq settings register */
#define ENE_IRQ_MASK 0x0F /* irq number mask */
#define ENE_IRQ_UNK_EN 0x10 /* always enabled */
#define ENE_IRQ_STATUS 0x20 /* irq status and ACK */
/* CIR Config register #1 */
#define ENE_CIRCFG 0xFEC0
#define ENE_CIRCFG_RX_EN 0x01 /* RX enable */
#define ENE_CIRCFG_RX_IRQ 0x02 /* Enable hardware interrupt */
#define ENE_CIRCFG_REV_POL 0x04 /* Input polarity reversed */
#define ENE_CIRCFG_CARR_DEMOD 0x08 /* Enable carrier demodulator */
#define ENE_CIRCFG_TX_EN 0x10 /* TX enable */
#define ENE_CIRCFG_TX_IRQ 0x20 /* Send interrupt on TX done */
#define ENE_CIRCFG_TX_POL_REV 0x40 /* TX polarity reversed */
#define ENE_CIRCFG_TX_CARR 0x80 /* send TX carrier or not */
/* CIR config register #2 */
#define ENE_CIRCFG2 0xFEC1
#define ENE_CIRCFG2_RLC 0x00
#define ENE_CIRCFG2_RC5 0x01
#define ENE_CIRCFG2_RC6 0x02
#define ENE_CIRCFG2_NEC 0x03
#define ENE_CIRCFG2_CARR_DETECT 0x10 /* Enable carrier detection */
#define ENE_CIRCFG2_GPIO0A 0x20 /* Use GPIO0A instead of GPIO40 for input */
#define ENE_CIRCFG2_FAST_SAMPL1 0x40 /* Fast leading pulse detection for RC6 */
#define ENE_CIRCFG2_FAST_SAMPL2 0x80 /* Fast data detection for RC6 */
/* Knobs for protocol decoding - will document when/if will use them */
#define ENE_CIRPF 0xFEC2
#define ENE_CIRHIGH 0xFEC3
#define ENE_CIRBIT 0xFEC4
#define ENE_CIRSTART 0xFEC5
#define ENE_CIRSTART2 0xFEC6
/* Actual register which contains RLC RX data - read by firmware */
#define ENE_CIRDAT_IN 0xFEC7
/* RLC configuration - sample period (1us resulution) + idle mode */
#define ENE_CIRRLC_CFG 0xFEC8
#define ENE_CIRRLC_CFG_OVERFLOW 0x80 /* interrupt on overflows if set */
#define ENE_DEFAULT_SAMPLE_PERIOD 50
/* Two byte RLC TX buffer */
#define ENE_CIRRLC_OUT0 0xFEC9
#define ENE_CIRRLC_OUT1 0xFECA
#define ENE_CIRRLC_OUT_PULSE 0x80 /* Transmitted sample is pulse */
#define ENE_CIRRLC_OUT_MASK 0x7F
/* Carrier detect setting
* Low nibble - number of carrier pulses to average
* High nibble - number of initial carrier pulses to discard
*/
#define ENE_CIRCAR_PULS 0xFECB
/* detected RX carrier period (resolution: 500 ns) */
#define ENE_CIRCAR_PRD 0xFECC
#define ENE_CIRCAR_PRD_VALID 0x80 /* data valid content valid */
/* Unknown TX setting - TX sample period ??? */
#define ENE_TX_UNK1 0xFECB /* set to 0x63 */
/* detected RX carrier pulse width (resolution: 500 ns) */
#define ENE_CIRCAR_HPRD 0xFECD
/* Current received carrier period */
#define ENE_RX_CARRIER 0xFECC /* RX period (500 ns) */
#define ENE_RX_CARRIER_VALID 0x80 /* Register content valid */
/* TX period (resolution: 500 ns, minimum 2)*/
#define ENE_CIRMOD_PRD 0xFECE
#define ENE_CIRMOD_PRD_POL 0x80 /* TX carrier polarity*/
#define ENE_CIRMOD_PRD_MAX 0x7F /* 15.87 kHz */
#define ENE_CIRMOD_PRD_MIN 0x02 /* 1 Mhz */
/* TX period (1/carrier) */
#define ENE_TX_PERIOD 0xFECE /* TX period (500 ns) */
#define ENE_TX_PERIOD_UNKBIT 0x80 /* This bit set on transmit*/
#define ENE_TX_PERIOD_PULSE 0xFECF /* TX pulse period (500 ns)*/
/* TX pulse width (resolution: 500 ns)*/
#define ENE_CIRMOD_HPRD 0xFECF
/* Hardware versions */
#define ENE_HW_VERSION 0xFF00 /* hardware revision */
#define ENE_ECHV 0xFF00 /* hardware revision */
#define ENE_PLLFRH 0xFF16
#define ENE_PLLFRL 0xFF17
#define ENE_DEFAULT_PLL_FREQ 1000
#define ENE_HW_UNK 0xFF1D
#define ENE_HW_UNK_CLR 0x04
#define ENE_HW_VER_MAJOR 0xFF1E /* chip version */
#define ENE_HW_VER_MINOR 0xFF1F
#define ENE_HW_VER_OLD 0xFD00
/* Normal/Learning carrier ranges - only valid if we have learning input*/
/* TODO: test */
#define ENE_NORMAL_RX_LOW 34
#define ENE_NORMAL_RX_HI 38
#define ENE_ECSTS 0xFF1D
#define ENE_ECSTS_RSRVD 0x04
/* Tx carrier range */
/* Hardware might be able to do more, but this range is enough for
all purposes */
#define ENE_TX_PERIOD_MAX 32 /* corresponds to 29.4 kHz */
#define ENE_TX_PERIOD_MIN 16 /* corrsponds to 62.5 kHz */
/* Minimal and maximal gaps */
/* Normal case:
Minimal gap is 0x7F * sample period
Maximum gap depends on hardware.
For KB3926B, it is unlimited, for newer models its around
250000, after which HW stops sending samples, and that is
not possible to change */
/* Fan case:
Both minimal and maximal gaps are same, and equal to 0xFFF * 0x61
And there is nothing to change this setting
*/
#define ENE_MAXGAP 250000
#define ENE_MINGAP (127 * sample_period)
#define ENE_ECVER_MAJOR 0xFF1E /* chip version */
#define ENE_ECVER_MINOR 0xFF1F
#define ENE_HW_VER_OLD 0xFD00
/******************************************************************************/
......@@ -171,46 +180,60 @@
#define ENE_HW_B 1 /* 3926B */
#define ENE_HW_C 2 /* 3926C */
#define ENE_HW_D 3 /* 3926D */
#define ENE_HW_D 3 /* 3926D or later */
#define ene_printk(level, text, ...) \
printk(level ENE_DRIVER_NAME ": " text, ## __VA_ARGS__)
printk(level ENE_DRIVER_NAME ": " text "\n", ## __VA_ARGS__)
#define ene_dbg(text, ...) \
if (debug) \
printk(KERN_DEBUG \
ENE_DRIVER_NAME ": " text "\n" , ## __VA_ARGS__)
#define ene_notice(text, ...) ene_printk(KERN_NOTICE, text, ## __VA_ARGS__)
#define ene_warn(text, ...) ene_printk(KERN_WARNING, text, ## __VA_ARGS__)
#define ene_dbg_verbose(text, ...) \
if (debug > 1) \
printk(KERN_DEBUG \
ENE_DRIVER_NAME ": " text "\n" , ## __VA_ARGS__)
#define __dbg(level, format, ...) \
do { \
if (debug >= level) \
printk(KERN_DEBUG ENE_DRIVER_NAME \
": " format "\n", ## __VA_ARGS__); \
} while (0)
#define dbg(format, ...) __dbg(1, format, ## __VA_ARGS__)
#define dbg_verbose(format, ...) __dbg(2, format, ## __VA_ARGS__)
#define dbg_regs(format, ...) __dbg(3, format, ## __VA_ARGS__)
#define MS_TO_NS(msec) ((msec) * 1000)
struct ene_device {
struct pnp_dev *pnp_dev;
struct input_dev *idev;
struct ir_dev_props *props;
int in_use;
/* hw IO settings */
unsigned long hw_io;
long hw_io;
int irq;
spinlock_t hw_lock;
/* HW features */
int hw_revision; /* hardware revision */
bool hw_learning_and_tx_capable; /* learning capable */
bool hw_gpio40_learning; /* gpio40 is learning */
bool hw_fan_as_normal_input; /* fan input is used as */
/* regular input */
bool hw_use_gpio_0a; /* gpio40 is demodulated input*/
bool hw_extra_buffer; /* hardware has 'extra buffer' */
bool hw_fan_input; /* fan input is IR data source */
bool hw_learning_and_tx_capable; /* learning & tx capable */
int pll_freq;
int buffer_len;
/* Extra RX buffer location */
int extra_buf1_address;
int extra_buf1_len;
int extra_buf2_address;
int extra_buf2_len;
/* HW state*/
int rx_pointer; /* hw pointer to rx buffer */
int r_pointer; /* pointer to next sample to read */
int w_pointer; /* pointer to next sample hw will write */
bool rx_fan_input_inuse; /* is fan input in use for rx*/
int tx_reg; /* current reg used for TX */
u8 saved_conf1; /* saved FEC0 reg */
/* TX sample handling */
unsigned int tx_sample; /* current sample for TX */
bool tx_sample_pulse; /* current sample is pulse */
......@@ -232,4 +255,8 @@ struct ene_device {
bool learning_enabled; /* learning input enabled */
bool carrier_detect_enabled; /* carrier detect enabled */
int rx_period_adjust;
bool rx_enabled;
};
static int ene_irq_status(struct ene_device *dev);
static void ene_read_hw_pointer(struct ene_device *dev);
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或