Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
提交 0ffd89e4 编写于 作者: P Paul Gortmaker
浏览文件
操作

drivers/net: delete Digital EtherWorks-3 support. 

This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.

Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:

	 "...designed to  work with all kernels > 1.1.33"
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
上级 1f1c7a5c
展开全部 隐藏空白更改
内联 并排
Showing with 0 addition and 2352 deletion
Documentation/networking/00-INDEX
浏览文件 @ 0ffd89e4
......@@ -70,8 +70,6 @@ e1000e.txt
- README for the Intel Gigabit Ethernet Driver (e1000e).
eql.txt
- serial IP load balancing
ewrk3.txt
- the Digital EtherWORKS 3 DE203/4/5 Ethernet driver
fib_trie.txt
- Level Compressed Trie (LC-trie) notes: a structure for routing.
filter.txt
......
Documentation/networking/ewrk3.txt 已删除 100644 → 0
浏览文件 @ 1f1c7a5c
The EtherWORKS 3 driver in this distribution is designed to work with all
kernels > 1.1.33 (approx) and includes tools in the 'ewrk3tools'
subdirectory to allow set up of the card, similar to the MSDOS
'NICSETUP.EXE' tools provided on the DOS drivers disk (type 'make' in that
subdirectory to make the tools).
The supported cards are DE203, DE204 and DE205. All other cards are NOT
supported - refer to 'depca.c' for running the LANCE based network cards and
'de4x5.c' for the DIGITAL Semiconductor PCI chip based adapters from
Digital.
The ability to load this driver as a loadable module has been included and
used extensively during the driver development (to save those long reboot
sequences). To utilise this ability, you have to do 8 things:
0) have a copy of the loadable modules code installed on your system.
1) copy ewrk3.c from the /linux/drivers/net directory to your favourite
temporary directory.
2) edit the source code near line 1898 to reflect the I/O address and
IRQ you're using.
3) compile ewrk3.c, but include -DMODULE in the command line to ensure
that the correct bits are compiled (see end of source code).
4) if you are wanting to add a new card, goto 5. Otherwise, recompile a
kernel with the ewrk3 configuration turned off and reboot.
5) insmod ewrk3.o
[Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
[Adam Kropelin: Multiple cards now supported by irq=x1,x2 io=y1,y2]
6) run the net startup bits for your new eth?? interface manually
(usually /etc/rc.inet[12] at boot time).
7) enjoy!
Note that autoprobing is not allowed in loadable modules - the system is
already up and running and you're messing with interrupts.
To unload a module, turn off the associated interface
'ifconfig eth?? down' then 'rmmod ewrk3'.
The performance we've achieved so far has been measured through the 'ttcp'
tool at 975kB/s. This measures the total TCP stack performance which
includes the card, so don't expect to get much nearer the 1.25MB/s
theoretical Ethernet rate.
Enjoy!
Dave
drivers/net/Space.c
浏览文件 @ 0ffd89e4
......@@ -43,7 +43,6 @@ extern struct net_device *wd_probe(int unit);
extern struct net_device *ne_probe(int unit);
extern struct net_device *fmv18x_probe(int unit);
extern struct net_device *i82596_probe(int unit);
extern struct net_device *ewrk3_probe(int unit);
extern struct net_device *ni65_probe(int unit);
extern struct net_device *sonic_probe(int unit);
extern struct net_device *seeq8005_probe(int unit);
......@@ -122,9 +121,6 @@ static struct devprobe2 isa_probes[] __initdata = {
{cs89x0_probe, 0},
#endif
#endif
#ifdef CONFIG_EWRK3 /* DEC EtherWORKS 3 */
{ewrk3_probe, 0},
#endif
#if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET) /* Intel I82596 */
{i82596_probe, 0},
#endif
......
drivers/net/ethernet/dec/Kconfig
浏览文件 @ 0ffd89e4
......@@ -17,21 +17,5 @@ config NET_VENDOR_DEC
your specific card in the following questions.
if NET_VENDOR_DEC
config EWRK3
tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
depends on ISA
select CRC32
---help---
This driver supports the DE203, DE204 and DE205 network (Ethernet)
cards. If this is for you, say Y and read
<file:Documentation/networking/ewrk3.txt> in the kernel source as
well as the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
To compile this driver as a module, choose M here. The module
will be called ewrk3.
source "drivers/net/ethernet/dec/tulip/Kconfig"
endif # NET_VENDOR_DEC
drivers/net/ethernet/dec/Makefile
浏览文件 @ 0ffd89e4
......@@ -2,5 +2,4 @@
# Makefile for the Digital Equipment Inc. network device drivers.
#
obj-$(CONFIG_EWRK3) += ewrk3.o
obj-$(CONFIG_NET_TULIP) += tulip/
drivers/net/ethernet/dec/ewrk3.c 已删除 100644 → 0
浏览文件 @ 1f1c7a5c
此差异已折叠。
drivers/net/ethernet/dec/ewrk3.h 已删除 100644 → 0
浏览文件 @ 1f1c7a5c
/*
Written 1994 by David C. Davies.
Copyright 1994 Digital Equipment Corporation.
This software may be used and distributed according to the terms of the
GNU General Public License, incorporated herein by reference.
The author may be reached as davies@wanton.lkg.dec.com or Digital
Equipment Corporation, 550 King Street, Littleton MA 01460.
=========================================================================
*/
/*
** I/O Address Register Map
*/
#define EWRK3_CSR iobase+0x00 /* Control and Status Register */
#define EWRK3_CR iobase+0x01 /* Control Register */
#define EWRK3_ICR iobase+0x02 /* Interrupt Control Register */
#define EWRK3_TSR iobase+0x03 /* Transmit Status Register */
#define EWRK3_RSVD1 iobase+0x04 /* RESERVED */
#define EWRK3_RSVD2 iobase+0x05 /* RESERVED */
#define EWRK3_FMQ iobase+0x06 /* Free Memory Queue */
#define EWRK3_FMQC iobase+0x07 /* Free Memory Queue Counter */
#define EWRK3_RQ iobase+0x08 /* Receive Queue */
#define EWRK3_RQC iobase+0x09 /* Receive Queue Counter */
#define EWRK3_TQ iobase+0x0a /* Transmit Queue */
#define EWRK3_TQC iobase+0x0b /* Transmit Queue Counter */
#define EWRK3_TDQ iobase+0x0c /* Transmit Done Queue */
#define EWRK3_TDQC iobase+0x0d /* Transmit Done Queue Counter */
#define EWRK3_PIR1 iobase+0x0e /* Page Index Register 1 */
#define EWRK3_PIR2 iobase+0x0f /* Page Index Register 2 */
#define EWRK3_DATA iobase+0x10 /* Data Register */
#define EWRK3_IOPR iobase+0x11 /* I/O Page Register */
#define EWRK3_IOBR iobase+0x12 /* I/O Base Register */
#define EWRK3_MPR iobase+0x13 /* Memory Page Register */
#define EWRK3_MBR iobase+0x14 /* Memory Base Register */
#define EWRK3_APROM iobase+0x15 /* Address PROM */
#define EWRK3_EPROM1 iobase+0x16 /* EEPROM Data Register 1 */
#define EWRK3_EPROM2 iobase+0x17 /* EEPROM Data Register 2 */
#define EWRK3_PAR0 iobase+0x18 /* Physical Address Register 0 */
#define EWRK3_PAR1 iobase+0x19 /* Physical Address Register 1 */
#define EWRK3_PAR2 iobase+0x1a /* Physical Address Register 2 */
#define EWRK3_PAR3 iobase+0x1b /* Physical Address Register 3 */
#define EWRK3_PAR4 iobase+0x1c /* Physical Address Register 4 */
#define EWRK3_PAR5 iobase+0x1d /* Physical Address Register 5 */
#define EWRK3_CMR iobase+0x1e /* Configuration/Management Register */
/*
** Control Page Map
*/
#define PAGE0_FMQ 0x000 /* Free Memory Queue */
#define PAGE0_RQ 0x080 /* Receive Queue */
#define PAGE0_TQ 0x100 /* Transmit Queue */
#define PAGE0_TDQ 0x180 /* Transmit Done Queue */
#define PAGE0_HTE 0x200 /* Hash Table Entries */
#define PAGE0_RSVD 0x240 /* RESERVED */
#define PAGE0_USRD 0x600 /* User Data */
/*
** Control and Status Register bit definitions (EWRK3_CSR)
*/
#define CSR_RA 0x80 /* Runt Accept */
#define CSR_PME 0x40 /* Promiscuous Mode Enable */
#define CSR_MCE 0x20 /* Multicast Enable */
#define CSR_TNE 0x08 /* TX Done Queue Not Empty */
#define CSR_RNE 0x04 /* RX Queue Not Empty */
#define CSR_TXD 0x02 /* TX Disable */
#define CSR_RXD 0x01 /* RX Disable */
/*
** Control Register bit definitions (EWRK3_CR)
*/
#define CR_APD 0x80 /* Auto Port Disable */
#define CR_PSEL 0x40 /* Port Select (0->TP port) */
#define CR_LBCK 0x20 /* LoopBaCK enable */
#define CR_FDUP 0x10 /* Full DUPlex enable */
#define CR_FBUS 0x08 /* Fast BUS enable (ISA clk > 8.33MHz) */
#define CR_EN_16 0x04 /* ENable 16 bit memory accesses */
#define CR_LED 0x02 /* LED (1-> turn on) */
/*
** Interrupt Control Register bit definitions (EWRK3_ICR)
*/
#define ICR_IE 0x80 /* Interrupt Enable */
#define ICR_IS 0x60 /* Interrupt Selected */
#define ICR_TNEM 0x08 /* TNE Mask (0->mask) */
#define ICR_RNEM 0x04 /* RNE Mask (0->mask) */
#define ICR_TXDM 0x02 /* TXD Mask (0->mask) */
#define ICR_RXDM 0x01 /* RXD Mask (0->mask) */
/*
** Transmit Status Register bit definitions (EWRK3_TSR)
*/
#define TSR_NCL 0x80 /* No Carrier Loopback */
#define TSR_ID 0x40 /* Initially Deferred */
#define TSR_LCL 0x20 /* Late CoLlision */
#define TSR_ECL 0x10 /* Excessive CoLlisions */
#define TSR_RCNTR 0x0f /* Retries CouNTeR */
/*
** I/O Page Register bit definitions (EWRK3_IOPR)
*/
#define EEPROM_INIT 0xc0 /* EEPROM INIT command */
#define EEPROM_WR_EN 0xc8 /* EEPROM WRITE ENABLE command */
#define EEPROM_WR 0xd0 /* EEPROM WRITE command */
#define EEPROM_WR_DIS 0xd8 /* EEPROM WRITE DISABLE command */
#define EEPROM_RD 0xe0 /* EEPROM READ command */
/*
** I/O Base Register bit definitions (EWRK3_IOBR)
*/
#define EISA_REGS_EN 0x20 /* Enable EISA ID and Control Registers */
#define EISA_IOB 0x1f /* Compare bits for I/O Base Address */
/*
** I/O Configuration/Management Register bit definitions (EWRK3_CMR)
*/
#define CMR_RA 0x80 /* Read Ahead */
#define CMR_WB 0x40 /* Write Behind */
#define CMR_LINK 0x20 /* 0->TP */
#define CMR_POLARITY 0x10 /* Informational */
#define CMR_NO_EEPROM 0x0c /* NO_EEPROM<1:0> pin status */
#define CMR_HS 0x08 /* Hard Strapped pin status (LeMAC2) */
#define CMR_PNP 0x04 /* Plug 'n Play */
#define CMR_DRAM 0x02 /* 0-> 1DRAM, 1-> 2 DRAM on board */
#define CMR_0WS 0x01 /* Zero Wait State */
/*
** MAC Receive Status Register bit definitions
*/
#define R_ROK 0x80 /* Receive OK summary */
#define R_IAM 0x10 /* Individual Address Match */
#define R_MCM 0x08 /* MultiCast Match */
#define R_DBE 0x04 /* Dribble Bit Error */
#define R_CRC 0x02 /* CRC error */
#define R_PLL 0x01 /* Phase Lock Lost */
/*
** MAC Transmit Control Register bit definitions
*/
#define TCR_SQEE 0x40 /* SQE Enable - look for heartbeat */
#define TCR_SED 0x20 /* Stop when Error Detected */
#define TCR_QMODE 0x10 /* Q_MODE */
#define TCR_LAB 0x08 /* Less Aggressive Backoff */
#define TCR_PAD 0x04 /* PAD Runt Packets */
#define TCR_IFC 0x02 /* Insert Frame Check */
#define TCR_ISA 0x01 /* Insert Source Address */
/*
** MAC Transmit Status Register bit definitions
*/
#define T_VSTS 0x80 /* Valid STatuS */
#define T_CTU 0x40 /* Cut Through Used */
#define T_SQE 0x20 /* Signal Quality Error */
#define T_NCL 0x10 /* No Carrier Loopback */
#define T_LCL 0x08 /* Late Collision */
#define T_ID 0x04 /* Initially Deferred */
#define T_COLL 0x03 /* COLLision status */
#define T_XCOLL 0x03 /* Excessive Collisions */
#define T_MCOLL 0x02 /* Multiple Collisions */
#define T_OCOLL 0x01 /* One Collision */
#define T_NOCOLL 0x00 /* No Collisions */
#define T_XUR 0x03 /* Excessive Underruns */
#define T_TXE 0x7f /* TX Errors */
/*
** EISA Configuration Register bit definitions
*/
#define EISA_ID iobase + 0x0c80 /* EISA ID Registers */
#define EISA_ID0 iobase + 0x0c80 /* EISA ID Register 0 */
#define EISA_ID1 iobase + 0x0c81 /* EISA ID Register 1 */
#define EISA_ID2 iobase + 0x0c82 /* EISA ID Register 2 */
#define EISA_ID3 iobase + 0x0c83 /* EISA ID Register 3 */
#define EISA_CR iobase + 0x0c84 /* EISA Control Register */
/*
** EEPROM BYTES
*/
#define EEPROM_MEMB 0x00
#define EEPROM_IOB 0x01
#define EEPROM_EISA_ID0 0x02
#define EEPROM_EISA_ID1 0x03
#define EEPROM_EISA_ID2 0x04
#define EEPROM_EISA_ID3 0x05
#define EEPROM_MISC0 0x06
#define EEPROM_MISC1 0x07
#define EEPROM_PNAME7 0x08
#define EEPROM_PNAME6 0x09
#define EEPROM_PNAME5 0x0a
#define EEPROM_PNAME4 0x0b
#define EEPROM_PNAME3 0x0c
#define EEPROM_PNAME2 0x0d
#define EEPROM_PNAME1 0x0e
#define EEPROM_PNAME0 0x0f
#define EEPROM_SWFLAGS 0x10
#define EEPROM_HWCAT 0x11
#define EEPROM_NETMAN2 0x12
#define EEPROM_REVLVL 0x13
#define EEPROM_NETMAN0 0x14
#define EEPROM_NETMAN1 0x15
#define EEPROM_CHIPVER 0x16
#define EEPROM_SETUP 0x17
#define EEPROM_PADDR0 0x18
#define EEPROM_PADDR1 0x19
#define EEPROM_PADDR2 0x1a
#define EEPROM_PADDR3 0x1b
#define EEPROM_PADDR4 0x1c
#define EEPROM_PADDR5 0x1d
#define EEPROM_PA_CRC 0x1e
#define EEPROM_CHKSUM 0x1f
/*
** EEPROM bytes for checksumming
*/
#define EEPROM_MAX 32 /* bytes */
/*
** EEPROM MISCELLANEOUS FLAGS
*/
#define RBE_SHADOW 0x0100 /* Remote Boot Enable Shadow */
#define READ_AHEAD 0x0080 /* Read Ahead feature */
#define IRQ_SEL2 0x0070 /* IRQ line selection (LeMAC2) */
#define IRQ_SEL 0x0060 /* IRQ line selection */
#define FAST_BUS 0x0008 /* ISA Bus speeds > 8.33MHz */
#define ENA_16 0x0004 /* Enables 16 bit memory transfers */
#define WRITE_BEHIND 0x0002 /* Write Behind feature */
#define _0WS_ENA 0x0001 /* Zero Wait State Enable */
/*
** EEPROM NETWORK MANAGEMENT FLAGS
*/
#define NETMAN_POL 0x04 /* Polarity defeat */
#define NETMAN_LINK 0x02 /* Link defeat */
#define NETMAN_CCE 0x01 /* Custom Counters Enable */
/*
** EEPROM SW FLAGS
*/
#define SW_SQE 0x10 /* Signal Quality Error */
#define SW_LAB 0x08 /* Less Aggressive Backoff */
#define SW_INIT 0x04 /* Initialized */
#define SW_TIMEOUT 0x02 /* 0:2.5 mins, 1: 30 secs */
#define SW_REMOTE 0x01 /* Remote Boot Enable -> 1 */
/*
** EEPROM SETUP FLAGS
*/
#define SETUP_APD 0x80 /* AutoPort Disable */
#define SETUP_PS 0x40 /* Port Select */
#define SETUP_MP 0x20 /* MultiPort */
#define SETUP_1TP 0x10 /* 1 port, TP */
#define SETUP_1COAX 0x00 /* 1 port, Coax */
#define SETUP_DRAM 0x02 /* Number of DRAMS on board */
/*
** EEPROM MANAGEMENT FLAGS
*/
#define MGMT_CCE 0x01 /* Custom Counters Enable */
/*
** EEPROM VERSIONS
*/
#define LeMAC 0x11
#define LeMAC2 0x12
/*
** Miscellaneous
*/
#define EEPROM_WAIT_TIME 1000 /* Number of microseconds */
#define EISA_EN 0x0001 /* Enable EISA bus buffers */
#define HASH_TABLE_LEN 512 /* Bits */
#define XCT 0x80 /* Transmit Cut Through */
#define PRELOAD 16 /* 4 long words */
#define MASK_INTERRUPTS 1
#define UNMASK_INTERRUPTS 0
#define EEPROM_OFFSET(a) ((u_short)((u_long)(a)))
/*
** Include the IOCTL stuff
*/
#include <linux/sockios.h>
#define EWRK3IOCTL SIOCDEVPRIVATE
struct ewrk3_ioctl {
unsigned short cmd; /* Command to run */
unsigned short len; /* Length of the data buffer */
unsigned char __user *data; /* Pointer to the data buffer */
};
/*
** Recognised commands for the driver
*/
#define EWRK3_GET_HWADDR 0x01 /* Get the hardware address */
#define EWRK3_SET_HWADDR 0x02 /* Get the hardware address */
#define EWRK3_SET_PROM 0x03 /* Set Promiscuous Mode */
#define EWRK3_CLR_PROM 0x04 /* Clear Promiscuous Mode */
#define EWRK3_SAY_BOO 0x05 /* Say "Boo!" to the kernel log file */
#define EWRK3_GET_MCA 0x06 /* Get a multicast address */
#define EWRK3_SET_MCA 0x07 /* Set a multicast address */
#define EWRK3_CLR_MCA 0x08 /* Clear a multicast address */
#define EWRK3_MCA_EN 0x09 /* Enable a multicast address group */
#define EWRK3_GET_STATS 0x0a /* Get the driver statistics */
#define EWRK3_CLR_STATS 0x0b /* Zero out the driver statistics */
#define EWRK3_GET_CSR 0x0c /* Get the CSR Register contents */
#define EWRK3_SET_CSR 0x0d /* Set the CSR Register contents */
#define EWRK3_GET_EEPROM 0x0e /* Get the EEPROM contents */
#define EWRK3_SET_EEPROM 0x0f /* Set the EEPROM contents */
#define EWRK3_GET_CMR 0x10 /* Get the CMR Register contents */
#define EWRK3_CLR_TX_CUT_THRU 0x11 /* Clear the TX cut through mode */
#define EWRK3_SET_TX_CUT_THRU 0x12 /* Set the TX cut through mode */
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或