Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (25 commits)
  sh: fix up sh7785lcr_32bit_defconfig.
  arch/sh/lib/strlen.S: Checkpatch cleanup
  sh: fix up sh7786 dmaengine build.
  sh: guard cookie consistency across termination in the DMA driver
  sh: prevent the DMA driver from unloading, while in use
  sh: fix Oops in the serial SCI driver
  sh: allow platforms to specify SD-card supported voltages
  mmc: let MFD's provide supported Vdd card voltages to tmio_mmc
  sh: disable SD-card write-protection detection on kfr2r09
  mfd: pass platform flags down to the tmio_mmc driver
  tmio: add a platform flag to disable card write-protection detection
  sh: Add SDHI DMA support to migor
  sh: Add SDHI DMA support to kfr2r09
  sh: Add SDHI DMA support to ms7724se
  sh: Add SDHI DMA support to ecovec
  mmc: add DMA support to tmio_mmc driver, when used on SuperH
  sh: prepare the SDHI MFD driver to pass DMA configuration to tmio_mmc.c
  mmc: prepare tmio_mmc for passing of DMA configuration from the MFD cell
  sh: add DMA slave definitions to sh7724
  sh: add DMA slaves for two SDHI controllers to sh7722
  ...

arch/sh/boards/mach-ecovec24/setup.c

@@ -11,6 +11,7 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/sh_mobile_sdhi.h>
 #include <linux/mtd/physmap.h>
 #include <linux/gpio.h>
 #include <linux/interrupt.h>
@@ -442,7 +443,9 @@ static void sdhi0_set_pwr(struct platform_device *pdev, int state)
 }
 
 static struct sh_mobile_sdhi_info sdhi0_info = {
-	.set_pwr = sdhi0_set_pwr,
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI0_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI0_RX,
+	.set_pwr	= sdhi0_set_pwr,
 };
 
 static struct resource sdhi0_resources[] = {
@@ -478,7 +481,9 @@ static void sdhi1_set_pwr(struct platform_device *pdev, int state)
 }
 
 static struct sh_mobile_sdhi_info sdhi1_info = {
-	.set_pwr = sdhi1_set_pwr,
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI1_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI1_RX,
+	.set_pwr	= sdhi1_set_pwr,
 };
 
 static struct resource sdhi1_resources[] = {
@@ -769,6 +774,51 @@ static struct platform_device irda_device = {
 	.resource       = irda_resources,
 };
 
+#include <media/ak881x.h>
+#include <media/sh_vou.h>
+
+struct ak881x_pdata ak881x_pdata = {
+	.flags = AK881X_IF_MODE_SLAVE,
+};
+
+static struct i2c_board_info ak8813 = {
+	I2C_BOARD_INFO("ak8813", 0x20),
+	.platform_data = &ak881x_pdata,
+};
+
+struct sh_vou_pdata sh_vou_pdata = {
+	.bus_fmt	= SH_VOU_BUS_8BIT,
+	.flags		= SH_VOU_HSYNC_LOW | SH_VOU_VSYNC_LOW,
+	.board_info	= &ak8813,
+	.i2c_adap	= 0,
+	.module_name	= "ak881x",
+};
+
+static struct resource sh_vou_resources[] = {
+	[0] = {
+		.start  = 0xfe960000,
+		.end    = 0xfe962043,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 55,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device vou_device = {
+	.name           = "sh-vou",
+	.id		= -1,
+	.num_resources  = ARRAY_SIZE(sh_vou_resources),
+	.resource       = sh_vou_resources,
+	.dev		= {
+		.platform_data	= &sh_vou_pdata,
+	},
+	.archdata	= {
+		.hwblk_id	= HWBLK_VOU,
+	},
+};
+
 static struct platform_device *ecovec_devices[] __initdata = {
 	&heartbeat_device,
 	&nor_flash_device,
@@ -790,6 +840,7 @@ static struct platform_device *ecovec_devices[] __initdata = {
 	&camera_devices[2],
 	&fsi_device,
 	&irda_device,
+	&vou_device,
 };
 
 #ifdef CONFIG_I2C
@@ -1179,6 +1230,38 @@ static int __init arch_setup(void)
 	i2c_register_board_info(1, i2c1_devices,
 				ARRAY_SIZE(i2c1_devices));
 
+	/* VOU */
+	gpio_request(GPIO_FN_DV_D15, NULL);
+	gpio_request(GPIO_FN_DV_D14, NULL);
+	gpio_request(GPIO_FN_DV_D13, NULL);
+	gpio_request(GPIO_FN_DV_D12, NULL);
+	gpio_request(GPIO_FN_DV_D11, NULL);
+	gpio_request(GPIO_FN_DV_D10, NULL);
+	gpio_request(GPIO_FN_DV_D9, NULL);
+	gpio_request(GPIO_FN_DV_D8, NULL);
+	gpio_request(GPIO_FN_DV_CLKI, NULL);
+	gpio_request(GPIO_FN_DV_CLK, NULL);
+	gpio_request(GPIO_FN_DV_VSYNC, NULL);
+	gpio_request(GPIO_FN_DV_HSYNC, NULL);
+
+	/* AK8813 power / reset sequence */
+	gpio_request(GPIO_PTG4, NULL);
+	gpio_request(GPIO_PTU3, NULL);
+	/* Reset */
+	gpio_direction_output(GPIO_PTG4, 0);
+	/* Power down */
+	gpio_direction_output(GPIO_PTU3, 1);
+
+	udelay(10);
+
+	/* Power up, reset */
+	gpio_set_value(GPIO_PTU3, 0);
+
+	udelay(10);
+
+	/* Remove reset */
+	gpio_set_value(GPIO_PTG4, 1);
+
 	return platform_add_devices(ecovec_devices,
 				    ARRAY_SIZE(ecovec_devices));
 }

arch/sh/boards/mach-kfr2r09/setup.c

@@ -10,6 +10,8 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
+#include <linux/mfd/sh_mobile_sdhi.h>
+#include <linux/mfd/tmio.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/onenand.h>
 #include <linux/delay.h>
@@ -356,10 +358,19 @@ static struct resource kfr2r09_sh_sdhi0_resources[] = {
 	},
 };
 
+static struct sh_mobile_sdhi_info sh7724_sdhi0_data = {
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI0_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI0_RX,
+	.tmio_flags	= TMIO_MMC_WRPROTECT_DISABLE,
+};
+
 static struct platform_device kfr2r09_sh_sdhi0_device = {
 	.name           = "sh_mobile_sdhi",
 	.num_resources  = ARRAY_SIZE(kfr2r09_sh_sdhi0_resources),
 	.resource       = kfr2r09_sh_sdhi0_resources,
+	.dev = {
+		.platform_data	= &sh7724_sdhi0_data,
+	},
 	.archdata = {
 		.hwblk_id = HWBLK_SDHI0,
 	},

arch/sh/boards/mach-migor/setup.c

@@ -12,6 +12,7 @@
 #include <linux/interrupt.h>
 #include <linux/input.h>
 #include <linux/input/sh_keysc.h>
+#include <linux/mfd/sh_mobile_sdhi.h>
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/nand.h>
 #include <linux/i2c.h>
@@ -402,10 +403,18 @@ static struct resource sdhi_cn9_resources[] = {
 	},
 };
 
+static struct sh_mobile_sdhi_info sh7724_sdhi_data = {
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI0_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI0_RX,
+};
+
 static struct platform_device sdhi_cn9_device = {
 	.name		= "sh_mobile_sdhi",
 	.num_resources	= ARRAY_SIZE(sdhi_cn9_resources),
 	.resource	= sdhi_cn9_resources,
+	.dev = {
+		.platform_data	= &sh7724_sdhi_data,
+	},
 	.archdata = {
 		.hwblk_id = HWBLK_SDHI,
 	},

arch/sh/boards/mach-se/7724/setup.c

@@ -14,6 +14,7 @@
 #include <linux/device.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/mfd/sh_mobile_sdhi.h>
 #include <linux/mtd/physmap.h>
 #include <linux/delay.h>
 #include <linux/smc91x.h>
@@ -462,11 +463,19 @@ static struct resource sdhi0_cn7_resources[] = {
 	},
 };
 
+static struct sh_mobile_sdhi_info sh7724_sdhi0_data = {
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI0_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI0_RX,
+};
+
 static struct platform_device sdhi0_cn7_device = {
 	.name           = "sh_mobile_sdhi",
 	.id		= 0,
 	.num_resources  = ARRAY_SIZE(sdhi0_cn7_resources),
 	.resource       = sdhi0_cn7_resources,
+	.dev = {
+		.platform_data	= &sh7724_sdhi0_data,
+	},
 	.archdata = {
 		.hwblk_id = HWBLK_SDHI0,
 	},
@@ -485,11 +494,19 @@ static struct resource sdhi1_cn8_resources[] = {
 	},
 };
 
+static struct sh_mobile_sdhi_info sh7724_sdhi1_data = {
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI1_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI1_RX,
+};
+
 static struct platform_device sdhi1_cn8_device = {
 	.name           = "sh_mobile_sdhi",
 	.id		= 1,
 	.num_resources  = ARRAY_SIZE(sdhi1_cn8_resources),
 	.resource       = sdhi1_cn8_resources,
+	.dev = {
+		.platform_data	= &sh7724_sdhi1_data,
+	},
 	.archdata = {
 		.hwblk_id = HWBLK_SDHI1,
 	},
@@ -515,6 +532,52 @@ static struct platform_device irda_device = {
 	.resource       = irda_resources,
 };
 
+#include <media/ak881x.h>
+#include <media/sh_vou.h>
+
+struct ak881x_pdata ak881x_pdata = {
+	.flags = AK881X_IF_MODE_SLAVE,
+};
+
+static struct i2c_board_info ak8813 = {
+	/* With open J18 jumper address is 0x21 */
+	I2C_BOARD_INFO("ak8813", 0x20),
+	.platform_data = &ak881x_pdata,
+};
+
+struct sh_vou_pdata sh_vou_pdata = {
+	.bus_fmt	= SH_VOU_BUS_8BIT,
+	.flags		= SH_VOU_HSYNC_LOW | SH_VOU_VSYNC_LOW,
+	.board_info	= &ak8813,
+	.i2c_adap	= 0,
+	.module_name	= "ak881x",
+};
+
+static struct resource sh_vou_resources[] = {
+	[0] = {
+		.start  = 0xfe960000,
+		.end    = 0xfe962043,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = 55,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device vou_device = {
+	.name           = "sh-vou",
+	.id		= -1,
+	.num_resources  = ARRAY_SIZE(sh_vou_resources),
+	.resource       = sh_vou_resources,
+	.dev		= {
+		.platform_data	= &sh_vou_pdata,
+	},
+	.archdata	= {
+		.hwblk_id	= HWBLK_VOU,
+	},
+};
+
 static struct platform_device *ms7724se_devices[] __initdata = {
 	&heartbeat_device,
 	&smc91x_eth_device,
@@ -530,6 +593,7 @@ static struct platform_device *ms7724se_devices[] __initdata = {
 	&sdhi0_cn7_device,
 	&sdhi1_cn8_device,
 	&irda_device,
+	&vou_device,
 };
 
 /* I2C device */
@@ -614,6 +678,7 @@ static int __init devices_setup(void)
 {
 	u16 sw = __raw_readw(SW4140); /* select camera, monitor */
 	struct clk *clk;
+	u16 fpga_out;
 
 	/* register board specific self-refresh code */
 	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF |
@@ -623,14 +688,26 @@ static int __init devices_setup(void)
 					&ms7724se_sdram_leave_start,
 					&ms7724se_sdram_leave_end);
 	/* Reset Release */
-	__raw_writew(__raw_readw(FPGA_OUT) &
-		  ~((1 << 1)  | /* LAN */
-		    (1 << 6)  | /* VIDEO DAC */
-		    (1 << 7)  | /* AK4643 */
-		    (1 << 8)  | /* IrDA */
-		    (1 << 12) | /* USB0 */
-		    (1 << 14)), /* RMII */
-		  FPGA_OUT);
+	fpga_out = __raw_readw(FPGA_OUT);
+	/* bit4: NTSC_PDN, bit5: NTSC_RESET */
+	fpga_out &= ~((1 << 1)  | /* LAN */
+		      (1 << 4)  | /* AK8813 PDN */
+		      (1 << 5)  | /* AK8813 RESET */
+		      (1 << 6)  | /* VIDEO DAC */
+		      (1 << 7)  | /* AK4643 */
+		      (1 << 8)  | /* IrDA */
+		      (1 << 12) | /* USB0 */
+		      (1 << 14)); /* RMII */
+	__raw_writew(fpga_out | (1 << 4), FPGA_OUT);
+
+	udelay(10);
+
+	/* AK8813 RESET */
+	__raw_writew(fpga_out | (1 << 5), FPGA_OUT);
+
+	udelay(10);
+
+	__raw_writew(fpga_out, FPGA_OUT);
 
 	/* turn on USB clocks, use external clock */
 	__raw_writew((__raw_readw(PORT_MSELCRB) & ~0xc000) | 0x8000, PORT_MSELCRB);
@@ -862,6 +939,20 @@ static int __init devices_setup(void)
 		lcdc_info.ch[0].flags          = LCDC_FLAGS_DWPOL;
 	}
 
+	/* VOU */
+	gpio_request(GPIO_FN_DV_D15, NULL);
+	gpio_request(GPIO_FN_DV_D14, NULL);
+	gpio_request(GPIO_FN_DV_D13, NULL);
+	gpio_request(GPIO_FN_DV_D12, NULL);
+	gpio_request(GPIO_FN_DV_D11, NULL);
+	gpio_request(GPIO_FN_DV_D10, NULL);
+	gpio_request(GPIO_FN_DV_D9, NULL);
+	gpio_request(GPIO_FN_DV_D8, NULL);
+	gpio_request(GPIO_FN_DV_CLKI, NULL);
+	gpio_request(GPIO_FN_DV_CLK, NULL);
+	gpio_request(GPIO_FN_DV_VSYNC, NULL);
+	gpio_request(GPIO_FN_DV_HSYNC, NULL);
+
 	return platform_add_devices(ms7724se_devices,
 				    ARRAY_SIZE(ms7724se_devices));
 }

arch/sh/configs/sh7785lcr_32bit_defconfig

 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.34-rc5
-# Tue May 18 17:22:09 2010
+# Linux kernel version: 2.6.34
+# Mon May 24 08:33:02 2010
 #
 CONFIG_SUPERH=y
 CONFIG_SUPERH32=y
@@ -76,7 +76,7 @@ CONFIG_RCU_FANOUT=32
 # CONFIG_TREE_RCU_TRACE is not set
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=14
+CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_CGROUPS is not set
 # CONFIG_SYSFS_DEPRECATED_V2 is not set
 # CONFIG_RELAY is not set
@@ -111,18 +111,17 @@ CONFIG_PERF_USE_VMALLOC=y
 #
 CONFIG_PERF_EVENTS=y
 CONFIG_PERF_COUNTERS=y
+# CONFIG_DEBUG_PERF_USE_VMALLOC is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_PCI_QUIRKS=y
-CONFIG_COMPAT_BRK=y
+# CONFIG_COMPAT_BRK is not set
 CONFIG_SLAB=y
 # CONFIG_SLUB is not set
 # CONFIG_SLOB is not set
 CONFIG_PROFILING=y
-CONFIG_TRACEPOINTS=y
-CONFIG_OPROFILE=y
+# CONFIG_OPROFILE is not set
 CONFIG_HAVE_OPROFILE=y
-CONFIG_KPROBES=y
-CONFIG_KRETPROBES=y
+# CONFIG_KPROBES is not set
 CONFIG_HAVE_KPROBES=y
 CONFIG_HAVE_KRETPROBES=y
 CONFIG_HAVE_ARCH_TRACEHOOK=y
@@ -130,6 +129,7 @@ CONFIG_HAVE_DMA_ATTRS=y
 CONFIG_HAVE_CLK=y
 CONFIG_HAVE_DMA_API_DEBUG=y
 CONFIG_HAVE_HW_BREAKPOINT=y
+CONFIG_HAVE_MIXED_BREAKPOINTS_REGS=y
 
 #
 # GCOV-based kernel profiling
@@ -243,8 +243,9 @@ CONFIG_PAGE_OFFSET=0x80000000
 CONFIG_FORCE_MAX_ZONEORDER=11
 CONFIG_MEMORY_START=0x40000000
 CONFIG_MEMORY_SIZE=0x20000000
-CONFIG_29BIT=y
-# CONFIG_PMB is not set
+# CONFIG_29BIT is not set
+CONFIG_32BIT=y
+CONFIG_PMB=y
 CONFIG_X2TLB=y
 CONFIG_VSYSCALL=y
 # CONFIG_NUMA is not set
@@ -262,9 +263,9 @@ CONFIG_PAGE_SIZE_4KB=y
 # CONFIG_PAGE_SIZE_8KB is not set
 # CONFIG_PAGE_SIZE_16KB is not set
 # CONFIG_PAGE_SIZE_64KB is not set
-CONFIG_HUGETLB_PAGE_SIZE_64K=y
+# CONFIG_HUGETLB_PAGE_SIZE_64K is not set
 # CONFIG_HUGETLB_PAGE_SIZE_256K is not set
-# CONFIG_HUGETLB_PAGE_SIZE_1MB is not set
+CONFIG_HUGETLB_PAGE_SIZE_1MB=y
 # CONFIG_HUGETLB_PAGE_SIZE_4MB is not set
 # CONFIG_HUGETLB_PAGE_SIZE_64MB is not set
 # CONFIG_HUGETLB_PAGE_SIZE_512MB is not set
@@ -276,7 +277,7 @@ CONFIG_SPARSEMEM=y
 CONFIG_HAVE_MEMORY_PRESENT=y
 CONFIG_SPARSEMEM_STATIC=y
 # CONFIG_MEMORY_HOTPLUG is not set
-CONFIG_SPLIT_PTLOCK_CPUS=4
+CONFIG_SPLIT_PTLOCK_CPUS=999999
 CONFIG_MIGRATION=y
 # CONFIG_PHYS_ADDR_T_64BIT is not set
 CONFIG_ZONE_DMA_FLAG=0
@@ -298,7 +299,7 @@ CONFIG_CPU_LITTLE_ENDIAN=y
 # CONFIG_CPU_BIG_ENDIAN is not set
 CONFIG_SH_FPU=y
 CONFIG_SH_STORE_QUEUES=y
-# CONFIG_SPECULATIVE_EXECUTION is not set
+CONFIG_SPECULATIVE_EXECUTION=y
 CONFIG_CPU_HAS_INTEVT=y
 CONFIG_CPU_HAS_SR_RB=y
 CONFIG_CPU_HAS_FPU=y
@@ -308,7 +309,7 @@ CONFIG_CPU_HAS_FPU=y
 #
 # CONFIG_SH_HIGHLANDER is not set
 CONFIG_SH_SH7785LCR=y
-CONFIG_SH_SH7785LCR_29BIT_PHYSMAPS=y
+# CONFIG_SH_SH7785LCR_PT is not set
 
 #
 # Timer and clock configuration
@@ -371,7 +372,7 @@ CONFIG_SECCOMP=y
 # CONFIG_PREEMPT_VOLUNTARY is not set
 CONFIG_PREEMPT=y
 CONFIG_GUSA=y
-# CONFIG_INTC_USERIMASK is not set
+CONFIG_INTC_USERIMASK=y
 
 #
 # Boot options
@@ -389,6 +390,7 @@ CONFIG_PCI=y
 CONFIG_PCI_DOMAINS=y
 # CONFIG_PCIEPORTBUS is not set
 # CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_DEBUG=y
 # CONFIG_PCI_STUB is not set
 # CONFIG_PCI_IOV is not set
 # CONFIG_PCCARD is not set
@@ -465,6 +467,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_RDS is not set
 # CONFIG_TIPC is not set
 # CONFIG_ATM is not set
+# CONFIG_L2TP is not set
 # CONFIG_BRIDGE is not set
 # CONFIG_NET_DSA is not set
 # CONFIG_VLAN_8021Q is not set
@@ -485,8 +488,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # Network testing
 #
 # CONFIG_NET_PKTGEN is not set
-# CONFIG_NET_TCPPROBE is not set
-# CONFIG_NET_DROP_MONITOR is not set
 # CONFIG_HAMRADIO is not set
 # CONFIG_CAN is not set
 # CONFIG_IRDA is not set
@@ -499,10 +500,19 @@ CONFIG_WIRELESS=y
 #
 # CFG80211 needs to be enabled for MAC80211
 #
+
+#
+# Some wireless drivers require a rate control algorithm
+#
 # CONFIG_WIMAX is not set
 # CONFIG_RFKILL is not set
 # CONFIG_NET_9P is not set
 
+#
+# CAIF Support
+#
+# CONFIG_CAIF is not set
+
 #
 # Device Drivers
 #
@@ -514,7 +524,11 @@ CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 # CONFIG_DEVTMPFS is not set
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
 # CONFIG_SYS_HYPERVISOR is not set
 # CONFIG_CONNECTOR is not set
 CONFIG_MTD=y
@@ -537,6 +551,7 @@ CONFIG_MTD_BLOCK=y
 # CONFIG_INFTL is not set
 # CONFIG_RFD_FTL is not set
 # CONFIG_SSFDC is not set
+# CONFIG_SM_FTL is not set
 # CONFIG_MTD_OOPS is not set
 
 #
@@ -668,7 +683,9 @@ CONFIG_ATA=y
 CONFIG_ATA_VERBOSE_ERROR=y
 CONFIG_SATA_PMP=y
 # CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_AHCI_PLATFORM is not set
 # CONFIG_SATA_SIL24 is not set
+# CONFIG_SATA_INIC162X is not set
 CONFIG_ATA_SFF=y
 # CONFIG_SATA_SVW is not set
 # CONFIG_ATA_PIIX is not set
@@ -683,7 +700,6 @@ CONFIG_SATA_SIL=y
 # CONFIG_SATA_ULI is not set
 # CONFIG_SATA_VIA is not set
 # CONFIG_SATA_VITESSE is not set
-# CONFIG_SATA_INIC162X is not set
 # CONFIG_PATA_ALI is not set
 # CONFIG_PATA_AMD is not set
 # CONFIG_PATA_ARTOP is not set
@@ -753,8 +769,36 @@ CONFIG_NETDEVICES=y
 # CONFIG_TUN is not set
 # CONFIG_VETH is not set
 # CONFIG_ARCNET is not set
-# CONFIG_NET_ETHERNET is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_STNIC is not set
+# CONFIG_HAPPYMEAL is not set
+# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
+CONFIG_NET_VENDOR_3COM=y
+CONFIG_VORTEX=y
+# CONFIG_TYPHOON is not set
+# CONFIG_SMC91X is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_NET_TULIP is not set
+# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
+# CONFIG_KS8842 is not set
+# CONFIG_KS8851_MLL is not set
+# CONFIG_ATL2 is not set
 CONFIG_NETDEV_1000=y
 # CONFIG_ACENIC is not set
 # CONFIG_DL2K is not set
@@ -836,6 +880,7 @@ CONFIG_INPUT_KEYBOARD=y
 CONFIG_KEYBOARD_ATKBD=y
 # CONFIG_QT2160 is not set
 # CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_TCA6416 is not set
 # CONFIG_KEYBOARD_MAX7359 is not set
 # CONFIG_KEYBOARD_NEWTON is not set
 # CONFIG_KEYBOARD_OPENCORES is not set
@@ -884,6 +929,7 @@ CONFIG_HW_CONSOLE=y
 CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_DEVKMEM is not set
 # CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_N_GSM is not set
 # CONFIG_NOZOMI is not set
 
 #
@@ -901,6 +947,8 @@ CONFIG_SERIAL_CORE=y
 CONFIG_SERIAL_CORE_CONSOLE=y
 # CONFIG_SERIAL_JSM is not set
 # CONFIG_SERIAL_TIMBERDALE is not set
+# CONFIG_SERIAL_ALTERA_JTAGUART is not set
+# CONFIG_SERIAL_ALTERA_UART is not set
 CONFIG_UNIX98_PTYS=y
 CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
 # CONFIG_LEGACY_PTYS is not set
@@ -1071,7 +1119,7 @@ CONFIG_FB_CFB_IMAGEBLIT=y
 # CONFIG_FB_SIS is not set
 # CONFIG_FB_VIA is not set
 # CONFIG_FB_NEOMAGIC is not set
-# CONFIG_FB_KYRO is not set
+CONFIG_FB_KYRO=y
 # CONFIG_FB_3DFX is not set
 # CONFIG_FB_VOODOO1 is not set
 # CONFIG_FB_VT8623 is not set
@@ -1097,15 +1145,15 @@ CONFIG_FB_SM501=y
 #
 CONFIG_DUMMY_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
-# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
 # CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
 # CONFIG_FONTS is not set
 CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-# CONFIG_LOGO_LINUX_CLUT224 is not set
+CONFIG_LOGO_LINUX_MONO=y
+CONFIG_LOGO_LINUX_VGA16=y
+CONFIG_LOGO_LINUX_CLUT224=y
 CONFIG_LOGO_SUPERH_MONO=y
 CONFIG_LOGO_SUPERH_VGA16=y
 CONFIG_LOGO_SUPERH_CLUT224=y
@@ -1129,15 +1177,18 @@ CONFIG_SND_SEQ_HRTIMER_DEFAULT=y
 CONFIG_SND_DYNAMIC_MINORS=y
 # CONFIG_SND_SUPPORT_OLD_API is not set
 # CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_VERBOSE_PRINTK is not set
-# CONFIG_SND_DEBUG is not set
+CONFIG_SND_VERBOSE_PRINTK=y
+CONFIG_SND_DEBUG=y
+CONFIG_SND_DEBUG_VERBOSE=y
+CONFIG_SND_VMASTER=y
 CONFIG_SND_RAWMIDI_SEQ=y
 CONFIG_SND_OPL3_LIB_SEQ=y
 # CONFIG_SND_OPL4_LIB_SEQ is not set
 # CONFIG_SND_SBAWE_SEQ is not set
-# CONFIG_SND_EMU10K1_SEQ is not set
+CONFIG_SND_EMU10K1_SEQ=y
 CONFIG_SND_MPU401_UART=y
 CONFIG_SND_OPL3_LIB=y
+CONFIG_SND_AC97_CODEC=y
 # CONFIG_SND_DRIVERS is not set
 CONFIG_SND_PCI=y
 # CONFIG_SND_AD1889 is not set
@@ -1172,7 +1223,7 @@ CONFIG_SND_CMIPCI=y
 # CONFIG_SND_INDIGODJ is not set
 # CONFIG_SND_INDIGOIOX is not set
 # CONFIG_SND_INDIGODJX is not set
-# CONFIG_SND_EMU10K1 is not set
+CONFIG_SND_EMU10K1=y
 # CONFIG_SND_EMU10K1X is not set
 # CONFIG_SND_ENS1370 is not set
 # CONFIG_SND_ENS1371 is not set
@@ -1211,6 +1262,7 @@ CONFIG_SND_USB=y
 # CONFIG_SND_USB_CAIAQ is not set
 # CONFIG_SND_SOC is not set
 # CONFIG_SOUND_PRIME is not set
+CONFIG_AC97_BUS=y
 CONFIG_HID_SUPPORT=y
 CONFIG_HID=y
 # CONFIG_HIDRAW is not set
@@ -1226,44 +1278,42 @@ CONFIG_USB_HID=y
 # Special HID drivers
 #
 # CONFIG_HID_3M_PCT is not set
-CONFIG_HID_A4TECH=m
-CONFIG_HID_APPLE=m
-CONFIG_HID_BELKIN=m
-CONFIG_HID_CHERRY=m
-CONFIG_HID_CHICONY=m
-CONFIG_HID_CYPRESS=m
-CONFIG_HID_DRAGONRISE=m
-# CONFIG_DRAGONRISE_FF is not set
-CONFIG_HID_EZKEY=m
-CONFIG_HID_KYE=m
-CONFIG_HID_GYRATION=m
-CONFIG_HID_TWINHAN=m
-CONFIG_HID_KENSINGTON=m
-CONFIG_HID_LOGITECH=m
-# CONFIG_LOGITECH_FF is not set
-# CONFIG_LOGIRUMBLEPAD2_FF is not set
-# CONFIG_LOGIG940_FF is not set
-CONFIG_HID_MICROSOFT=m
+# CONFIG_HID_A4TECH is not set
+# CONFIG_HID_APPLE is not set
+# CONFIG_HID_BELKIN is not set
+# CONFIG_HID_CANDO is not set
+# CONFIG_HID_CHERRY is not set
+# CONFIG_HID_CHICONY is not set
+# CONFIG_HID_PRODIKEYS is not set
+# CONFIG_HID_CYPRESS is not set
+# CONFIG_HID_DRAGONRISE is not set
+# CONFIG_HID_EGALAX is not set
+# CONFIG_HID_EZKEY is not set
+# CONFIG_HID_KYE is not set
+# CONFIG_HID_GYRATION is not set
+# CONFIG_HID_TWINHAN is not set
+# CONFIG_HID_KENSINGTON is not set
+# CONFIG_HID_LOGITECH is not set
+# CONFIG_HID_MICROSOFT is not set
 # CONFIG_HID_MOSART is not set
-CONFIG_HID_MONTEREY=m
-CONFIG_HID_NTRIG=m
+# CONFIG_HID_MONTEREY is not set
+# CONFIG_HID_NTRIG is not set
 # CONFIG_HID_ORTEK is not set
-CONFIG_HID_PANTHERLORD=m
-# CONFIG_PANTHERLORD_FF is not set
-CONFIG_HID_PETALYNX=m
+# CONFIG_HID_PANTHERLORD is not set
+# CONFIG_HID_PETALYNX is not set
+# CONFIG_HID_PICOLCD is not set
 # CONFIG_HID_QUANTA is not set
-CONFIG_HID_SAMSUNG=m
-CONFIG_HID_SONY=m
+# CONFIG_HID_ROCCAT_KONE is not set
+# CONFIG_HID_SAMSUNG is not set
+# CONFIG_HID_SONY is not set
 # CONFIG_HID_STANTUM is not set
-CONFIG_HID_SUNPLUS=m
-CONFIG_HID_GREENASIA=m
-# CONFIG_GREENASIA_FF is not set
-CONFIG_HID_SMARTJOYPLUS=m
-# CONFIG_SMARTJOYPLUS_FF is not set
-CONFIG_HID_TOPSEED=m
+# CONFIG_HID_SUNPLUS is not set
+# CONFIG_HID_GREENASIA is not set
+# CONFIG_HID_SMARTJOYPLUS is not set
+# CONFIG_HID_TOPSEED is not set
 # CONFIG_HID_THRUSTMASTER is not set
-CONFIG_HID_ZEROPLUS=m
-# CONFIG_ZEROPLUS_FF is not set
+# CONFIG_HID_ZEROPLUS is not set
+# CONFIG_HID_ZYDACRON is not set
 CONFIG_USB_SUPPORT=y
 CONFIG_USB_ARCH_HAS_HCD=y
 CONFIG_USB_ARCH_HAS_OHCI=y
@@ -1276,9 +1326,8 @@ CONFIG_USB=y
 # Miscellaneous USB options
 #
 # CONFIG_USB_DEVICEFS is not set
-CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DEVICE_CLASS is not set
 # CONFIG_USB_DYNAMIC_MINORS is not set
-# CONFIG_USB_OTG is not set
 # CONFIG_USB_OTG_WHITELIST is not set
 # CONFIG_USB_OTG_BLACKLIST_HUB is not set
 # CONFIG_USB_MON is not set
@@ -1290,9 +1339,7 @@ CONFIG_USB_DEVICE_CLASS=y
 #
 # CONFIG_USB_C67X00_HCD is not set
 # CONFIG_USB_XHCI_HCD is not set
-CONFIG_USB_EHCI_HCD=m
-# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
-# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_EHCI_HCD is not set
 # CONFIG_USB_OXU210HP_HCD is not set
 # CONFIG_USB_ISP116X_HCD is not set
 # CONFIG_USB_ISP1760_HCD is not set
@@ -1361,7 +1408,6 @@ CONFIG_USB_STORAGE=y
 # CONFIG_USB_IDMOUSE is not set
 # CONFIG_USB_FTDI_ELAN is not set
 # CONFIG_USB_APPLEDISPLAY is not set
-# CONFIG_USB_SISUSBVGA is not set
 # CONFIG_USB_LD is not set
 # CONFIG_USB_TRANCEVIBRATOR is not set
 # CONFIG_USB_IOWARRIOR is not set
@@ -1464,6 +1510,7 @@ CONFIG_DMADEVICES=y
 #
 # DMA Devices
 #
+# CONFIG_TIMB_DMA is not set
 # CONFIG_AUXDISPLAY is not set
 CONFIG_UIO=m
 # CONFIG_UIO_CIF is not set
@@ -1473,10 +1520,6 @@ CONFIG_UIO=m
 # CONFIG_UIO_SERCOS3 is not set
 # CONFIG_UIO_PCI_GENERIC is not set
 # CONFIG_UIO_NETX is not set
-
-#
-# TI VLYNQ
-#
 # CONFIG_STAGING is not set
 
 #
@@ -1653,63 +1696,75 @@ CONFIG_MAGIC_SYSRQ=y
 # CONFIG_UNUSED_SYMBOLS is not set
 CONFIG_DEBUG_FS=y
 # CONFIG_HEADERS_CHECK is not set
-# CONFIG_DEBUG_KERNEL is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
 CONFIG_SCHED_DEBUG=y
 CONFIG_SCHEDSTATS=y
-CONFIG_TRACE_IRQFLAGS=y
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_DEBUG_SLAB is not set
+CONFIG_DEBUG_KMEMLEAK=y
+CONFIG_DEBUG_KMEMLEAK_EARLY_LOG_SIZE=400
+# CONFIG_DEBUG_KMEMLEAK_TEST is not set
+CONFIG_DEBUG_PREEMPT=y
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+CONFIG_DEBUG_SPINLOCK=y
+CONFIG_DEBUG_MUTEXES=y
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+CONFIG_DEBUG_SPINLOCK_SLEEP=y
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
 CONFIG_STACKTRACE=y
+# CONFIG_DEBUG_KOBJECT is not set
 CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
 # CONFIG_DEBUG_MEMORY_INIT is not set
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_DEBUG_CREDENTIALS is not set
 CONFIG_FRAME_POINTER=y
+# CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
 # CONFIG_LKDTM is not set
+# CONFIG_FAULT_INJECTION is not set
 CONFIG_LATENCYTOP=y
 CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_NOP_TRACER=y
-CONFIG_HAVE_FTRACE_NMI_ENTER=y
+# CONFIG_PAGE_POISONING is not set
 CONFIG_HAVE_FUNCTION_TRACER=y
 CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
 CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
 CONFIG_HAVE_DYNAMIC_FTRACE=y
 CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
 CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_TRACER_MAX_TRACE=y
-CONFIG_RING_BUFFER=y
-CONFIG_FTRACE_NMI_ENTER=y
-CONFIG_EVENT_TRACING=y
-CONFIG_CONTEXT_SWITCH_TRACER=y
-CONFIG_RING_BUFFER_ALLOW_SWAP=y
-CONFIG_TRACING=y
-CONFIG_GENERIC_TRACER=y
 CONFIG_TRACING_SUPPORT=y
-CONFIG_FTRACE=y
-CONFIG_FUNCTION_TRACER=y
-CONFIG_FUNCTION_GRAPH_TRACER=y
-CONFIG_IRQSOFF_TRACER=y
-# CONFIG_PREEMPT_TRACER is not set
-CONFIG_SCHED_TRACER=y
-# CONFIG_FTRACE_SYSCALLS is not set
-# CONFIG_BOOT_TRACER is not set
-CONFIG_BRANCH_PROFILE_NONE=y
-# CONFIG_PROFILE_ANNOTATED_BRANCHES is not set
-# CONFIG_PROFILE_ALL_BRANCHES is not set
-# CONFIG_KSYM_TRACER is not set
-CONFIG_STACK_TRACER=y
-CONFIG_KMEMTRACE=y
-CONFIG_WORKQUEUE_TRACER=y
-# CONFIG_BLK_DEV_IO_TRACE is not set
-CONFIG_DYNAMIC_FTRACE=y
-# CONFIG_FUNCTION_PROFILER is not set
-CONFIG_FTRACE_MCOUNT_RECORD=y
-# CONFIG_FTRACE_STARTUP_TEST is not set
-# CONFIG_RING_BUFFER_BENCHMARK is not set
+# CONFIG_FTRACE is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 # CONFIG_DMA_API_DEBUG is not set
+# CONFIG_ATOMIC64_SELFTEST is not set
 # CONFIG_SAMPLES is not set
 CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
 # CONFIG_SH_STANDARD_BIOS is not set
-CONFIG_DWARF_UNWINDER=y
-CONFIG_MCOUNT=y
+# CONFIG_STACK_DEBUG is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_4KSTACKS is not set
+CONFIG_DUMP_CODE=y
+# CONFIG_DWARF_UNWINDER is not set
+# CONFIG_SH_NO_BSS_INIT is not set
 
 #
 # Security options
@@ -1820,7 +1875,7 @@ CONFIG_CRYPTO_DES=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 # CONFIG_CRYPTO_HW is not set
 # CONFIG_VIRTUALIZATION is not set
-CONFIG_BINARY_PRINTF=y
+# CONFIG_BINARY_PRINTF is not set
 
 #
 # Library routines

arch/sh/include/asm/dmaengine.h

-/*
- * Header for the new SH dmaengine driver
- *
- * Copyright (C) 2010 Guennadi Liakhovetski <g.liakhovetski@gmx.de>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef ASM_DMAENGINE_H
-#define ASM_DMAENGINE_H
-
-#include <linux/sh_dma.h>
-
-enum {
-	SHDMA_SLAVE_SCIF0_TX,
-	SHDMA_SLAVE_SCIF0_RX,
-	SHDMA_SLAVE_SCIF1_TX,
-	SHDMA_SLAVE_SCIF1_RX,
-	SHDMA_SLAVE_SCIF2_TX,
-	SHDMA_SLAVE_SCIF2_RX,
-	SHDMA_SLAVE_SCIF3_TX,
-	SHDMA_SLAVE_SCIF3_RX,
-	SHDMA_SLAVE_SCIF4_TX,
-	SHDMA_SLAVE_SCIF4_RX,
-	SHDMA_SLAVE_SCIF5_TX,
-	SHDMA_SLAVE_SCIF5_RX,
-	SHDMA_SLAVE_SIUA_TX,
-	SHDMA_SLAVE_SIUA_RX,
-	SHDMA_SLAVE_SIUB_TX,
-	SHDMA_SLAVE_SIUB_RX,
-};
-
-#endif

arch/sh/include/asm/siu.h

@@ -11,8 +11,6 @@
 #ifndef ASM_SIU_H
 #define ASM_SIU_H
 
-#include <asm/dmaengine.h>
-
 struct device;
 
 struct siu_platform {

arch/sh/include/cpu-sh4/cpu/sh7722.h

@@ -235,4 +235,19 @@ enum {
 	HWBLK_NR,
 };
 
+enum {
+	SHDMA_SLAVE_SCIF0_TX,
+	SHDMA_SLAVE_SCIF0_RX,
+	SHDMA_SLAVE_SCIF1_TX,
+	SHDMA_SLAVE_SCIF1_RX,
+	SHDMA_SLAVE_SCIF2_TX,
+	SHDMA_SLAVE_SCIF2_RX,
+	SHDMA_SLAVE_SIUA_TX,
+	SHDMA_SLAVE_SIUA_RX,
+	SHDMA_SLAVE_SIUB_TX,
+	SHDMA_SLAVE_SIUB_RX,
+	SHDMA_SLAVE_SDHI0_TX,
+	SHDMA_SLAVE_SDHI0_RX,
+};
+
 #endif /* __ASM_SH7722_H__ */

arch/sh/include/cpu-sh4/cpu/sh7724.h

@@ -283,4 +283,23 @@ enum {
 	HWBLK_NR,
 };
 
+enum {
+	SHDMA_SLAVE_SCIF0_TX,
+	SHDMA_SLAVE_SCIF0_RX,
+	SHDMA_SLAVE_SCIF1_TX,
+	SHDMA_SLAVE_SCIF1_RX,
+	SHDMA_SLAVE_SCIF2_TX,
+	SHDMA_SLAVE_SCIF2_RX,
+	SHDMA_SLAVE_SCIF3_TX,
+	SHDMA_SLAVE_SCIF3_RX,
+	SHDMA_SLAVE_SCIF4_TX,
+	SHDMA_SLAVE_SCIF4_RX,
+	SHDMA_SLAVE_SCIF5_TX,
+	SHDMA_SLAVE_SCIF5_RX,
+	SHDMA_SLAVE_SDHI0_TX,
+	SHDMA_SLAVE_SDHI0_RX,
+	SHDMA_SLAVE_SDHI1_TX,
+	SHDMA_SLAVE_SDHI1_RX,
+};
+
 #endif /* __ASM_SH7724_H__ */

arch/sh/kernel/cpu/sh4a/clock-sh7786.c

@@ -13,7 +13,6 @@
 #include <linux/kernel.h>
 #include <linux/clk.h>
 #include <linux/io.h>
-#include <linux/clk.h>
 #include <asm/clkdev.h>
 #include <asm/clock.h>
 #include <asm/freq.h>

arch/sh/kernel/cpu/sh4a/setup-sh7722.c

@@ -17,7 +17,6 @@
 #include <linux/usb/m66592.h>
 
 #include <asm/clock.h>
-#include <asm/dmaengine.h>
 #include <asm/mmzone.h>
 #include <asm/siu.h>
 
@@ -75,6 +74,16 @@ static const struct sh_dmae_slave_config sh7722_dmae_slaves[] = {
 		.addr		= 0xa454c094,
 		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_32BIT),
 		.mid_rid	= 0xb6,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SDHI0_TX,
+		.addr		= 0x04ce0030,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc1,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SDHI0_RX,
+		.addr		= 0x04ce0030,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc2,
 	},
 };
 

arch/sh/kernel/cpu/sh4a/setup-sh7724.c

@@ -18,19 +18,103 @@
 #include <linux/mm.h>
 #include <linux/serial_sci.h>
 #include <linux/uio_driver.h>
+#include <linux/sh_dma.h>
 #include <linux/sh_timer.h>
 #include <linux/io.h>
 #include <linux/notifier.h>
 
 #include <asm/suspend.h>
 #include <asm/clock.h>
-#include <asm/dmaengine.h>
 #include <asm/mmzone.h>
 
 #include <cpu/dma-register.h>
 #include <cpu/sh7724.h>
 
 /* DMA */
+static const struct sh_dmae_slave_config sh7724_dmae_slaves[] = {
+	{
+		.slave_id	= SHDMA_SLAVE_SCIF0_TX,
+		.addr		= 0xffe0000c,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x21,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF0_RX,
+		.addr		= 0xffe00014,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x22,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF1_TX,
+		.addr		= 0xffe1000c,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x25,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF1_RX,
+		.addr		= 0xffe10014,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x26,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF2_TX,
+		.addr		= 0xffe2000c,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x29,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF2_RX,
+		.addr		= 0xffe20014,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x2a,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF3_TX,
+		.addr		= 0xa4e30020,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x2d,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF3_RX,
+		.addr		= 0xa4e30024,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x2e,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF4_TX,
+		.addr		= 0xa4e40020,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x31,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF4_RX,
+		.addr		= 0xa4e40024,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x32,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF5_TX,
+		.addr		= 0xa4e50020,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x35,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SCIF5_RX,
+		.addr		= 0xa4e50024,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_8BIT),
+		.mid_rid	= 0x36,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SDHI0_TX,
+		.addr		= 0x04ce0030,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc1,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SDHI0_RX,
+		.addr		= 0x04ce0030,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc2,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SDHI1_TX,
+		.addr		= 0x04cf0030,
+		.chcr		= DM_FIX | SM_INC | 0x800 | TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xc9,
+	}, {
+		.slave_id	= SHDMA_SLAVE_SDHI1_RX,
+		.addr		= 0x04cf0030,
+		.chcr		= DM_INC | SM_FIX | 0x800 | TS_INDEX2VAL(XMIT_SZ_16BIT),
+		.mid_rid	= 0xca,
+	},
+};
+
 static const struct sh_dmae_channel sh7724_dmae_channels[] = {
 	{
 		.offset = 0,
@@ -62,6 +146,8 @@ static const struct sh_dmae_channel sh7724_dmae_channels[] = {
 static const unsigned int ts_shift[] = TS_SHIFT;
 
 static struct sh_dmae_pdata dma_platform_data = {
+	.slave		= sh7724_dmae_slaves,
+	.slave_num	= ARRAY_SIZE(sh7724_dmae_slaves),
 	.channel	= sh7724_dmae_channels,
 	.channel_num	= ARRAY_SIZE(sh7724_dmae_channels),
 	.ts_low_shift	= CHCR_TS_LOW_SHIFT,

arch/sh/kernel/cpu/sh4a/setup-sh7780.c

@@ -12,10 +12,9 @@
 #include <linux/serial.h>
 #include <linux/io.h>
 #include <linux/serial_sci.h>
+#include <linux/sh_dma.h>
 #include <linux/sh_timer.h>
 
-#include <asm/dmaengine.h>
-
 #include <cpu/dma-register.h>
 
 static struct plat_sci_port scif0_platform_data = {

arch/sh/kernel/cpu/sh4a/setup-sh7785.c

@@ -13,9 +13,9 @@
 #include <linux/serial_sci.h>
 #include <linux/io.h>
 #include <linux/mm.h>
+#include <linux/sh_dma.h>
 #include <linux/sh_timer.h>
 
-#include <asm/dmaengine.h>
 #include <asm/mmzone.h>
 
 #include <cpu/dma-register.h>

arch/sh/kernel/cpu/sh4a/setup-sh7786.c

@@ -21,10 +21,10 @@
 #include <linux/mm.h>
 #include <linux/dma-mapping.h>
 #include <linux/sh_timer.h>
+#include <linux/sh_dma.h>
 #include <linux/sh_intc.h>
 #include <cpu/dma-register.h>
 #include <asm/mmzone.h>
-#include <asm/dmaengine.h>
 
 static struct plat_sci_port scif0_platform_data = {
 	.mapbase	= 0xffea0000,

arch/sh/kernel/dwarf.c

@@ -845,8 +845,10 @@ static int dwarf_parse_cie(void *entry, void *p, unsigned long len,
 	rb_link_node(&cie->node, parent, rb_node);
 	rb_insert_color(&cie->node, &cie_root);
 
+#ifdef CONFIG_MODULES
 	if (mod != NULL)
 		list_add_tail(&cie->link, &mod->arch.cie_list);
+#endif
 
 	spin_unlock_irqrestore(&dwarf_cie_lock, flags);
 
@@ -935,8 +937,10 @@ static int dwarf_parse_fde(void *entry, u32 entry_type,
 	rb_link_node(&fde->node, parent, rb_node);
 	rb_insert_color(&fde->node, &fde_root);
 
+#ifdef CONFIG_MODULES
 	if (mod != NULL)
 		list_add_tail(&fde->link, &mod->arch.fde_list);
+#endif
 
 	spin_unlock_irqrestore(&dwarf_fde_lock, flags);
 

arch/sh/lib/strlen.S

@@ -35,7 +35,7 @@ ENTRY(strlen)
 	mov.b	@r4+,r1
 	tst	r1,r1
 	bt	8f
-	add	#1,r2	
+	add	#1,r2
 
 1:
 	mov	#0,r3

drivers/dma/shdma.c

@@ -722,6 +722,10 @@ static void sh_dmae_chan_ld_cleanup(struct sh_dmae_chan *sh_chan, bool all)
 {
 	while (__ld_cleanup(sh_chan, all))
 		;
+
+	if (all)
+		/* Terminating - forgive uncompleted cookies */
+		sh_chan->completed_cookie = sh_chan->common.cookie;
 }
 
 static void sh_chan_xfer_ld_queue(struct sh_dmae_chan *sh_chan)
@@ -1188,6 +1192,7 @@ static struct platform_driver sh_dmae_driver = {
 	.remove		= __exit_p(sh_dmae_remove),
 	.shutdown	= sh_dmae_shutdown,
 	.driver = {
+		.owner	= THIS_MODULE,
 		.name	= "sh-dma-engine",
 	},
 };

drivers/mfd/Kconfig

@@ -49,6 +49,7 @@ config MFD_SH_MOBILE_SDHI
 	bool "Support for SuperH Mobile SDHI"
 	depends on SUPERH || ARCH_SHMOBILE
 	select MFD_CORE
+	select TMIO_MMC_DMA
 	 ---help---
 	  This driver supports the SDHI hardware block found in many
 	  SuperH Mobile SoCs.
@@ -162,6 +163,11 @@ config MFD_TMIO
 	bool
 	default n
 
+config TMIO_MMC_DMA
+	bool
+	select DMA_ENGINE
+	select DMADEVICES
+
 config MFD_T7L66XB
 	bool "Support Toshiba T7L66XB"
 	depends on ARM && HAVE_CLK

drivers/mfd/sh_mobile_sdhi.c

@@ -26,11 +26,15 @@
 #include <linux/mfd/core.h>
 #include <linux/mfd/tmio.h>
 #include <linux/mfd/sh_mobile_sdhi.h>
+#include <linux/sh_dma.h>
 
 struct sh_mobile_sdhi {
 	struct clk *clk;
 	struct tmio_mmc_data mmc_data;
 	struct mfd_cell cell_mmc;
+	struct sh_dmae_slave param_tx;
+	struct sh_dmae_slave param_rx;
+	struct tmio_mmc_dma dma_priv;
 };
 
 static struct resource sh_mobile_sdhi_resources[] = {
@@ -64,6 +68,8 @@ static void sh_mobile_sdhi_set_pwr(struct platform_device *tmio, int state)
 static int __init sh_mobile_sdhi_probe(struct platform_device *pdev)
 {
 	struct sh_mobile_sdhi *priv;
+	struct tmio_mmc_data *mmc_data;
+	struct sh_mobile_sdhi_info *p = pdev->dev.platform_data;
 	struct resource *mem;
 	char clk_name[8];
 	int ret, irq;
@@ -85,6 +91,8 @@ static int __init sh_mobile_sdhi_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
+	mmc_data = &priv->mmc_data;
+
 	snprintf(clk_name, sizeof(clk_name), "sdhi%d", pdev->id);
 	priv->clk = clk_get(&pdev->dev, clk_name);
 	if (IS_ERR(priv->clk)) {
@@ -96,12 +104,24 @@ static int __init sh_mobile_sdhi_probe(struct platform_device *pdev)
 
 	clk_enable(priv->clk);
 
-	priv->mmc_data.hclk = clk_get_rate(priv->clk);
-	priv->mmc_data.set_pwr = sh_mobile_sdhi_set_pwr;
-	priv->mmc_data.capabilities = MMC_CAP_MMC_HIGHSPEED;
+	mmc_data->hclk = clk_get_rate(priv->clk);
+	mmc_data->set_pwr = sh_mobile_sdhi_set_pwr;
+	mmc_data->capabilities = MMC_CAP_MMC_HIGHSPEED;
+	if (p) {
+		mmc_data->flags = p->tmio_flags;
+		mmc_data->ocr_mask = p->tmio_ocr_mask;
+	}
+
+	if (p && p->dma_slave_tx >= 0 && p->dma_slave_rx >= 0) {
+		priv->param_tx.slave_id = p->dma_slave_tx;
+		priv->param_rx.slave_id = p->dma_slave_rx;
+		priv->dma_priv.chan_priv_tx = &priv->param_tx;
+		priv->dma_priv.chan_priv_rx = &priv->param_rx;
+		mmc_data->dma = &priv->dma_priv;
+	}
 
 	memcpy(&priv->cell_mmc, &sh_mobile_sdhi_cell, sizeof(priv->cell_mmc));
-	priv->cell_mmc.driver_data = &priv->mmc_data;
+	priv->cell_mmc.driver_data = mmc_data;
 	priv->cell_mmc.platform_data = &priv->cell_mmc;
 	priv->cell_mmc.data_size = sizeof(priv->cell_mmc);
 

drivers/mmc/host/tmio_mmc.c

@@ -29,6 +29,7 @@
 #include <linux/irq.h>
 #include <linux/device.h>
 #include <linux/delay.h>
+#include <linux/dmaengine.h>
 #include <linux/mmc/host.h>
 #include <linux/mfd/core.h>
 #include <linux/mfd/tmio.h>
@@ -131,8 +132,8 @@ tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
 
 	host->cmd = cmd;
 
-/* FIXME - this seems to be ok comented out but the spec suggest this bit should
- *         be set when issuing app commands.
+/* FIXME - this seems to be ok commented out but the spec suggest this bit
+ *         should be set when issuing app commands.
  *	if(cmd->flags & MMC_FLAG_ACMD)
  *		c |= APP_CMD;
  */
@@ -155,12 +156,12 @@ tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
 	return 0;
 }
 
-/* This chip always returns (at least?) as much data as you ask for.
+/*
+ * This chip always returns (at least?) as much data as you ask for.
  * I'm unsure what happens if you ask for less than a block. This should be
  * looked into to ensure that a funny length read doesnt hose the controller.
- *
  */
-static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
+static void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
 {
 	struct mmc_data *data = host->data;
 	unsigned short *buf;
@@ -180,7 +181,7 @@ static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
 		count = data->blksz;
 
 	pr_debug("count: %08x offset: %08x flags %08x\n",
-	    count, host->sg_off, data->flags);
+		 count, host->sg_off, data->flags);
 
 	/* Transfer the data */
 	if (data->flags & MMC_DATA_READ)
@@ -198,7 +199,7 @@ static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
 	return;
 }
 
-static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
+static void tmio_mmc_do_data_irq(struct tmio_mmc_host *host)
 {
 	struct mmc_data *data = host->data;
 	struct mmc_command *stop;
@@ -206,7 +207,7 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 	host->data = NULL;
 
 	if (!data) {
-		pr_debug("Spurious data end IRQ\n");
+		dev_warn(&host->pdev->dev, "Spurious data end IRQ\n");
 		return;
 	}
 	stop = data->stop;
@@ -219,7 +220,8 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 
 	pr_debug("Completed data request\n");
 
-	/*FIXME - other drivers allow an optional stop command of any given type
+	/*
+	 * FIXME: other drivers allow an optional stop command of any given type
 	 *        which we dont do, as the chip can auto generate them.
 	 *        Perhaps we can be smarter about when to use auto CMD12 and
 	 *        only issue the auto request when we know this is the desired
@@ -227,10 +229,17 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 	 *        upper layers expect. For now, we do what works.
 	 */
 
-	if (data->flags & MMC_DATA_READ)
-		disable_mmc_irqs(host, TMIO_MASK_READOP);
-	else
-		disable_mmc_irqs(host, TMIO_MASK_WRITEOP);
+	if (data->flags & MMC_DATA_READ) {
+		if (!host->chan_rx)
+			disable_mmc_irqs(host, TMIO_MASK_READOP);
+		dev_dbg(&host->pdev->dev, "Complete Rx request %p\n",
+			host->mrq);
+	} else {
+		if (!host->chan_tx)
+			disable_mmc_irqs(host, TMIO_MASK_WRITEOP);
+		dev_dbg(&host->pdev->dev, "Complete Tx request %p\n",
+			host->mrq);
+	}
 
 	if (stop) {
 		if (stop->opcode == 12 && !stop->arg)
@@ -242,7 +251,35 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 	tmio_mmc_finish_request(host);
 }
 
-static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
+static void tmio_mmc_data_irq(struct tmio_mmc_host *host)
+{
+	struct mmc_data *data = host->data;
+
+	if (!data)
+		return;
+
+	if (host->chan_tx && (data->flags & MMC_DATA_WRITE)) {
+		/*
+		 * Has all data been written out yet? Testing on SuperH showed,
+		 * that in most cases the first interrupt comes already with the
+		 * BUSY status bit clear, but on some operations, like mount or
+		 * in the beginning of a write / sync / umount, there is one
+		 * DATAEND interrupt with the BUSY bit set, in this cases
+		 * waiting for one more interrupt fixes the problem.
+		 */
+		if (!(sd_ctrl_read32(host, CTL_STATUS) & TMIO_STAT_CMD_BUSY)) {
+			disable_mmc_irqs(host, TMIO_STAT_DATAEND);
+			tasklet_schedule(&host->dma_complete);
+		}
+	} else if (host->chan_rx && (data->flags & MMC_DATA_READ)) {
+		disable_mmc_irqs(host, TMIO_STAT_DATAEND);
+		tasklet_schedule(&host->dma_complete);
+	} else {
+		tmio_mmc_do_data_irq(host);
+	}
+}
+
+static void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 	unsigned int stat)
 {
 	struct mmc_command *cmd = host->cmd;
@@ -282,10 +319,16 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 	 * If theres no data or we encountered an error, finish now.
 	 */
 	if (host->data && !cmd->error) {
-		if (host->data->flags & MMC_DATA_READ)
-			enable_mmc_irqs(host, TMIO_MASK_READOP);
-		else
-			enable_mmc_irqs(host, TMIO_MASK_WRITEOP);
+		if (host->data->flags & MMC_DATA_READ) {
+			if (!host->chan_rx)
+				enable_mmc_irqs(host, TMIO_MASK_READOP);
+		} else {
+			struct dma_chan *chan = host->chan_tx;
+			if (!chan)
+				enable_mmc_irqs(host, TMIO_MASK_WRITEOP);
+			else
+				tasklet_schedule(&host->dma_issue);
+		}
 	} else {
 		tmio_mmc_finish_request(host);
 	}
@@ -293,7 +336,6 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 	return;
 }
 
-
 static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 {
 	struct tmio_mmc_host *host = devid;
@@ -311,7 +353,7 @@ static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 	if (!ireg) {
 		disable_mmc_irqs(host, status & ~irq_mask);
 
-		pr_debug("tmio_mmc: Spurious irq, disabling! "
+		pr_warning("tmio_mmc: Spurious irq, disabling! "
 			"0x%08x 0x%08x 0x%08x\n", status, irq_mask, ireg);
 		pr_debug_status(status);
 
@@ -363,16 +405,265 @@ static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 	return IRQ_HANDLED;
 }
 
+#ifdef CONFIG_TMIO_MMC_DMA
+static void tmio_mmc_enable_dma(struct tmio_mmc_host *host, bool enable)
+{
+#if defined(CONFIG_SUPERH) || defined(CONFIG_ARCH_SHMOBILE)
+	/* Switch DMA mode on or off - SuperH specific? */
+	sd_ctrl_write16(host, 0xd8, enable ? 2 : 0);
+#endif
+}
+
+static void tmio_dma_complete(void *arg)
+{
+	struct tmio_mmc_host *host = arg;
+
+	dev_dbg(&host->pdev->dev, "Command completed\n");
+
+	if (!host->data)
+		dev_warn(&host->pdev->dev, "NULL data in DMA completion!\n");
+	else
+		enable_mmc_irqs(host, TMIO_STAT_DATAEND);
+}
+
+static int tmio_mmc_start_dma_rx(struct tmio_mmc_host *host)
+{
+	struct scatterlist *sg = host->sg_ptr;
+	struct dma_async_tx_descriptor *desc = NULL;
+	struct dma_chan *chan = host->chan_rx;
+	int ret;
+
+	ret = dma_map_sg(&host->pdev->dev, sg, host->sg_len, DMA_FROM_DEVICE);
+	if (ret > 0) {
+		host->dma_sglen = ret;
+		desc = chan->device->device_prep_slave_sg(chan, sg, ret,
+			DMA_FROM_DEVICE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	}
+
+	if (desc) {
+		host->desc = desc;
+		desc->callback = tmio_dma_complete;
+		desc->callback_param = host;
+		host->cookie = desc->tx_submit(desc);
+		if (host->cookie < 0) {
+			host->desc = NULL;
+			ret = host->cookie;
+		} else {
+			chan->device->device_issue_pending(chan);
+		}
+	}
+	dev_dbg(&host->pdev->dev, "%s(): mapped %d -> %d, cookie %d, rq %p\n",
+		__func__, host->sg_len, ret, host->cookie, host->mrq);
+
+	if (!host->desc) {
+		/* DMA failed, fall back to PIO */
+		if (ret >= 0)
+			ret = -EIO;
+		host->chan_rx = NULL;
+		dma_release_channel(chan);
+		/* Free the Tx channel too */
+		chan = host->chan_tx;
+		if (chan) {
+			host->chan_tx = NULL;
+			dma_release_channel(chan);
+		}
+		dev_warn(&host->pdev->dev,
+			 "DMA failed: %d, falling back to PIO\n", ret);
+		tmio_mmc_enable_dma(host, false);
+		reset(host);
+		/* Fail this request, let above layers recover */
+		host->mrq->cmd->error = ret;
+		tmio_mmc_finish_request(host);
+	}
+
+	dev_dbg(&host->pdev->dev, "%s(): desc %p, cookie %d, sg[%d]\n", __func__,
+		desc, host->cookie, host->sg_len);
+
+	return ret > 0 ? 0 : ret;
+}
+
+static int tmio_mmc_start_dma_tx(struct tmio_mmc_host *host)
+{
+	struct scatterlist *sg = host->sg_ptr;
+	struct dma_async_tx_descriptor *desc = NULL;
+	struct dma_chan *chan = host->chan_tx;
+	int ret;
+
+	ret = dma_map_sg(&host->pdev->dev, sg, host->sg_len, DMA_TO_DEVICE);
+	if (ret > 0) {
+		host->dma_sglen = ret;
+		desc = chan->device->device_prep_slave_sg(chan, sg, ret,
+			DMA_TO_DEVICE, DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	}
+
+	if (desc) {
+		host->desc = desc;
+		desc->callback = tmio_dma_complete;
+		desc->callback_param = host;
+		host->cookie = desc->tx_submit(desc);
+		if (host->cookie < 0) {
+			host->desc = NULL;
+			ret = host->cookie;
+		}
+	}
+	dev_dbg(&host->pdev->dev, "%s(): mapped %d -> %d, cookie %d, rq %p\n",
+		__func__, host->sg_len, ret, host->cookie, host->mrq);
+
+	if (!host->desc) {
+		/* DMA failed, fall back to PIO */
+		if (ret >= 0)
+			ret = -EIO;
+		host->chan_tx = NULL;
+		dma_release_channel(chan);
+		/* Free the Rx channel too */
+		chan = host->chan_rx;
+		if (chan) {
+			host->chan_rx = NULL;
+			dma_release_channel(chan);
+		}
+		dev_warn(&host->pdev->dev,
+			 "DMA failed: %d, falling back to PIO\n", ret);
+		tmio_mmc_enable_dma(host, false);
+		reset(host);
+		/* Fail this request, let above layers recover */
+		host->mrq->cmd->error = ret;
+		tmio_mmc_finish_request(host);
+	}
+
+	dev_dbg(&host->pdev->dev, "%s(): desc %p, cookie %d\n", __func__,
+		desc, host->cookie);
+
+	return ret > 0 ? 0 : ret;
+}
+
+static int tmio_mmc_start_dma(struct tmio_mmc_host *host,
+			       struct mmc_data *data)
+{
+	if (data->flags & MMC_DATA_READ) {
+		if (host->chan_rx)
+			return tmio_mmc_start_dma_rx(host);
+	} else {
+		if (host->chan_tx)
+			return tmio_mmc_start_dma_tx(host);
+	}
+
+	return 0;
+}
+
+static void tmio_issue_tasklet_fn(unsigned long priv)
+{
+	struct tmio_mmc_host *host = (struct tmio_mmc_host *)priv;
+	struct dma_chan *chan = host->chan_tx;
+
+	chan->device->device_issue_pending(chan);
+}
+
+static void tmio_tasklet_fn(unsigned long arg)
+{
+	struct tmio_mmc_host *host = (struct tmio_mmc_host *)arg;
+
+	if (host->data->flags & MMC_DATA_READ)
+		dma_unmap_sg(&host->pdev->dev, host->sg_ptr, host->dma_sglen,
+			     DMA_FROM_DEVICE);
+	else
+		dma_unmap_sg(&host->pdev->dev, host->sg_ptr, host->dma_sglen,
+			     DMA_TO_DEVICE);
+
+	tmio_mmc_do_data_irq(host);
+}
+
+/* It might be necessary to make filter MFD specific */
+static bool tmio_mmc_filter(struct dma_chan *chan, void *arg)
+{
+	dev_dbg(chan->device->dev, "%s: slave data %p\n", __func__, arg);
+	chan->private = arg;
+	return true;
+}
+
+static void tmio_mmc_request_dma(struct tmio_mmc_host *host,
+				 struct tmio_mmc_data *pdata)
+{
+	host->cookie = -EINVAL;
+	host->desc = NULL;
+
+	/* We can only either use DMA for both Tx and Rx or not use it at all */
+	if (pdata->dma) {
+		dma_cap_mask_t mask;
+
+		dma_cap_zero(mask);
+		dma_cap_set(DMA_SLAVE, mask);
+
+		host->chan_tx = dma_request_channel(mask, tmio_mmc_filter,
+						    pdata->dma->chan_priv_tx);
+		dev_dbg(&host->pdev->dev, "%s: TX: got channel %p\n", __func__,
+			host->chan_tx);
+
+		if (!host->chan_tx)
+			return;
+
+		host->chan_rx = dma_request_channel(mask, tmio_mmc_filter,
+						    pdata->dma->chan_priv_rx);
+		dev_dbg(&host->pdev->dev, "%s: RX: got channel %p\n", __func__,
+			host->chan_rx);
+
+		if (!host->chan_rx) {
+			dma_release_channel(host->chan_tx);
+			host->chan_tx = NULL;
+			return;
+		}
+
+		tasklet_init(&host->dma_complete, tmio_tasklet_fn, (unsigned long)host);
+		tasklet_init(&host->dma_issue, tmio_issue_tasklet_fn, (unsigned long)host);
+
+		tmio_mmc_enable_dma(host, true);
+	}
+}
+
+static void tmio_mmc_release_dma(struct tmio_mmc_host *host)
+{
+	if (host->chan_tx) {
+		struct dma_chan *chan = host->chan_tx;
+		host->chan_tx = NULL;
+		dma_release_channel(chan);
+	}
+	if (host->chan_rx) {
+		struct dma_chan *chan = host->chan_rx;
+		host->chan_rx = NULL;
+		dma_release_channel(chan);
+	}
+
+	host->cookie = -EINVAL;
+	host->desc = NULL;
+}
+#else
+static int tmio_mmc_start_dma(struct tmio_mmc_host *host,
+			       struct mmc_data *data)
+{
+	return 0;
+}
+
+static void tmio_mmc_request_dma(struct tmio_mmc_host *host,
+				 struct tmio_mmc_data *pdata)
+{
+	host->chan_tx = NULL;
+	host->chan_rx = NULL;
+}
+
+static void tmio_mmc_release_dma(struct tmio_mmc_host *host)
+{
+}
+#endif
+
 static int tmio_mmc_start_data(struct tmio_mmc_host *host,
 	struct mmc_data *data)
 {
 	pr_debug("setup data transfer: blocksize %08x  nr_blocks %d\n",
-	    data->blksz, data->blocks);
+		 data->blksz, data->blocks);
 
 	/* Hardware cannot perform 1 and 2 byte requests in 4 bit mode */
 	if (data->blksz < 4 && host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) {
-		printk(KERN_ERR "%s: %d byte block unsupported in 4 bit mode\n",
-			mmc_hostname(host->mmc), data->blksz);
+		pr_err("%s: %d byte block unsupported in 4 bit mode\n",
+		       mmc_hostname(host->mmc), data->blksz);
 		return -EINVAL;
 	}
 
@@ -383,7 +674,7 @@ static int tmio_mmc_start_data(struct tmio_mmc_host *host,
 	sd_ctrl_write16(host, CTL_SD_XFER_LEN, data->blksz);
 	sd_ctrl_write16(host, CTL_XFER_BLK_COUNT, data->blocks);
 
-	return 0;
+	return tmio_mmc_start_dma(host, data);
 }
 
 /* Process requests from the MMC layer */
@@ -404,7 +695,6 @@ static void tmio_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
 	}
 
 	ret = tmio_mmc_start_command(host, mrq->cmd);
-
 	if (!ret)
 		return;
 
@@ -458,11 +748,14 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 static int tmio_mmc_get_ro(struct mmc_host *mmc)
 {
 	struct tmio_mmc_host *host = mmc_priv(mmc);
+	struct mfd_cell	*cell = host->pdev->dev.platform_data;
+	struct tmio_mmc_data *pdata = cell->driver_data;
 
-	return (sd_ctrl_read16(host, CTL_STATUS) & TMIO_STAT_WRPROTECT) ? 0 : 1;
+	return ((pdata->flags & TMIO_MMC_WRPROTECT_DISABLE) ||
+		(sd_ctrl_read32(host, CTL_STATUS) & TMIO_STAT_WRPROTECT)) ? 0 : 1;
 }
 
-static struct mmc_host_ops tmio_mmc_ops = {
+static const struct mmc_host_ops tmio_mmc_ops = {
 	.request	= tmio_mmc_request,
 	.set_ios	= tmio_mmc_set_ios,
 	.get_ro         = tmio_mmc_get_ro,
@@ -515,6 +808,7 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	struct tmio_mmc_host *host;
 	struct mmc_host *mmc;
 	int ret = -EINVAL;
+	u32 irq_mask = TMIO_MASK_CMD;
 
 	if (dev->num_resources != 2)
 		goto out;
@@ -553,7 +847,10 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	mmc->caps |= pdata->capabilities;
 	mmc->f_max = pdata->hclk;
 	mmc->f_min = mmc->f_max / 512;
-	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+	if (pdata->ocr_mask)
+		mmc->ocr_avail = pdata->ocr_mask;
+	else
+		mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	/* Tell the MFD core we are ready to be enabled */
 	if (cell->enable) {
@@ -578,13 +875,20 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	if (ret)
 		goto cell_disable;
 
+	/* See if we also get DMA */
+	tmio_mmc_request_dma(host, pdata);
+
 	mmc_add_host(mmc);
 
-	printk(KERN_INFO "%s at 0x%08lx irq %d\n", mmc_hostname(host->mmc),
-	       (unsigned long)host->ctl, host->irq);
+	pr_info("%s at 0x%08lx irq %d\n", mmc_hostname(host->mmc),
+		(unsigned long)host->ctl, host->irq);
 
 	/* Unmask the IRQs we want to know about */
-	enable_mmc_irqs(host, TMIO_MASK_IRQ);
+	if (!host->chan_rx)
+		irq_mask |= TMIO_MASK_READOP;
+	if (!host->chan_tx)
+		irq_mask |= TMIO_MASK_WRITEOP;
+	enable_mmc_irqs(host, irq_mask);
 
 	return 0;
 
@@ -609,6 +913,7 @@ static int __devexit tmio_mmc_remove(struct platform_device *dev)
 	if (mmc) {
 		struct tmio_mmc_host *host = mmc_priv(mmc);
 		mmc_remove_host(mmc);
+		tmio_mmc_release_dma(host);
 		free_irq(host->irq, host);
 		if (cell->disable)
 			cell->disable(dev);

drivers/mmc/host/tmio_mmc.h

@@ -10,6 +10,8 @@
  */
 
 #include <linux/highmem.h>
+#include <linux/interrupt.h>
+#include <linux/dmaengine.h>
 
 #define CTL_SD_CMD 0x00
 #define CTL_ARG_REG 0x04
@@ -106,6 +108,17 @@ struct tmio_mmc_host {
 	unsigned int            sg_off;
 
 	struct platform_device *pdev;
+
+	/* DMA support */
+	struct dma_chan		*chan_rx;
+	struct dma_chan		*chan_tx;
+	struct tasklet_struct	dma_complete;
+	struct tasklet_struct	dma_issue;
+#ifdef CONFIG_TMIO_MMC_DMA
+	struct dma_async_tx_descriptor *desc;
+	unsigned int            dma_sglen;
+	dma_cookie_t		cookie;
+#endif
 };
 
 #include <linux/io.h>

drivers/serial/sh-sci.c

@@ -1004,8 +1004,9 @@ static void sci_rx_dma_release(struct sci_port *s, bool enable_pio)
 	s->chan_rx = NULL;
 	s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL;
 	dma_release_channel(chan);
-	dma_free_coherent(port->dev, s->buf_len_rx * 2,
-			  sg_virt(&s->sg_rx[0]), sg_dma_address(&s->sg_rx[0]));
+	if (sg_dma_address(&s->sg_rx[0]))
+		dma_free_coherent(port->dev, s->buf_len_rx * 2,
+				  sg_virt(&s->sg_rx[0]), sg_dma_address(&s->sg_rx[0]));
 	if (enable_pio)
 		sci_start_rx(port);
 }

include/linux/mfd/sh_mobile_sdhi.h

 #ifndef __SH_MOBILE_SDHI_H__
 #define __SH_MOBILE_SDHI_H__
 
+#include <linux/types.h>
+
 struct sh_mobile_sdhi_info {
+	int dma_slave_tx;
+	int dma_slave_rx;
+	unsigned long tmio_flags;
+	u32 tmio_ocr_mask;	/* available MMC voltages */
 	void (*set_pwr)(struct platform_device *pdev, int state);
 };
 

include/linux/mfd/tmio.h

@@ -50,17 +50,28 @@
 		tmio_iowrite16((val) >> 16, (base) + ((reg + 2) << (shift))); \
 	} while (0)
 
+/* tmio MMC platform flags */
+#define TMIO_MMC_WRPROTECT_DISABLE	(1 << 0)
+
 int tmio_core_mmc_enable(void __iomem *cnf, int shift, unsigned long base);
 int tmio_core_mmc_resume(void __iomem *cnf, int shift, unsigned long base);
 void tmio_core_mmc_pwr(void __iomem *cnf, int shift, int state);
 void tmio_core_mmc_clk_div(void __iomem *cnf, int shift, int state);
 
+struct tmio_mmc_dma {
+	void *chan_priv_tx;
+	void *chan_priv_rx;
+};
+
 /*
  * data for the MMC controller
  */
 struct tmio_mmc_data {
 	unsigned int			hclk;
 	unsigned long			capabilities;
+	unsigned long			flags;
+	u32				ocr_mask;	/* available voltages */
+	struct tmio_mmc_dma		*dma;
 	void (*set_pwr)(struct platform_device *host, int state);
 	void (*set_clk_div)(struct platform_device *host, int state);
 };

sound/soc/sh/siu.h

@@ -71,8 +71,7 @@ struct siu_firmware {
 #include <linux/dmaengine.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
-
-#include <asm/dmaengine.h>
+#include <linux/sh_dma.h>
 
 #include <sound/core.h>
 #include <sound/pcm.h>

sound/soc/sh/siu_pcm.c

@@ -31,7 +31,6 @@
 #include <sound/pcm_params.h>
 #include <sound/soc-dai.h>
 
-#include <asm/dmaengine.h>
 #include <asm/siu.h>
 
 #include "siu.h"
@@ -358,13 +357,13 @@ static int siu_pcm_open(struct snd_pcm_substream *ss)
 	if (ss->stream == SNDRV_PCM_STREAM_PLAYBACK) {
 		siu_stream = &port_info->playback;
 		param = &siu_stream->param;
-		param->slave_id = port ? SHDMA_SLAVE_SIUB_TX :
-			SHDMA_SLAVE_SIUA_TX;
+		param->slave_id = port ? pdata->dma_slave_tx_b :
+			pdata->dma_slave_tx_a;
 	} else {
 		siu_stream = &port_info->capture;
 		param = &siu_stream->param;
-		param->slave_id = port ? SHDMA_SLAVE_SIUB_RX :
-			SHDMA_SLAVE_SIUA_RX;
+		param->slave_id = port ? pdata->dma_slave_rx_b :
+			pdata->dma_slave_rx_a;
 	}
 
 	param->dma_dev = pdata->dma_dev;