macb: Kill PHY reset code

With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/cadence/macb.h

@@ -1171,7 +1171,6 @@ struct macb {
 	unsigned int		dma_burst_length;
 
 	phy_interface_t		phy_interface;
-	struct gpio_desc	*reset_gpio;
 
 	/* AT91RM9200 transmit */
 	struct sk_buff *skb;			/* holds skb until xmit interrupt completes */

drivers/net/ethernet/cadence/macb_main.c

@@ -3803,7 +3803,6 @@ static int macb_probe(struct platform_device *pdev)
 					      = macb_config->clk_init;
 	int (*init)(struct platform_device *) = macb_config->init;
 	struct device_node *np = pdev->dev.of_node;
-	struct device_node *phy_node;
 	struct clk *pclk, *hclk = NULL, *tx_clk = NULL, *rx_clk = NULL;
 	unsigned int queue_mask, num_queues;
 	struct macb_platform_data *pdata;
@@ -3909,18 +3908,6 @@ static int macb_probe(struct platform_device *pdev)
 	else
 		macb_get_hwaddr(bp);
 
-	/* Power up the PHY if there is a GPIO reset */
-	phy_node =  of_get_next_available_child(np, NULL);
-	if (phy_node) {
-		int gpio = of_get_named_gpio(phy_node, "reset-gpios", 0);
-
-		if (gpio_is_valid(gpio)) {
-			bp->reset_gpio = gpio_to_desc(gpio);
-			gpiod_direction_output(bp->reset_gpio, 1);
-		}
-	}
-	of_node_put(phy_node);
-
 	err = of_get_phy_mode(np);
 	if (err < 0) {
 		pdata = dev_get_platdata(&pdev->dev);
@@ -3967,10 +3954,6 @@ static int macb_probe(struct platform_device *pdev)
 		of_phy_deregister_fixed_link(np);
 	mdiobus_free(bp->mii_bus);
 
-	/* Shutdown the PHY if there is a GPIO reset */
-	if (bp->reset_gpio)
-		gpiod_set_value(bp->reset_gpio, 0);
-
 err_out_free_netdev:
 	free_netdev(dev);
 
@@ -4001,10 +3984,6 @@ static int macb_remove(struct platform_device *pdev)
 		dev->phydev = NULL;
 		mdiobus_free(bp->mii_bus);
 
-		/* Shutdown the PHY if there is a GPIO reset */
-		if (bp->reset_gpio)
-			gpiod_set_value(bp->reset_gpio, 0);
-
 		unregister_netdev(dev);
 		clk_disable_unprepare(bp->tx_clk);
 		clk_disable_unprepare(bp->hclk);