powerpc/eeh: Fix stale cached primary bus

When PE is created, its primary bus is cached to pe->bus. At later
point, the cached primary bus is returned from eeh_pe_bus_get().
However, we could get stale cached primary bus and run into kernel
crash in one case: full hotplug as part of fenced PHB error recovery
releases all PCI busses under the PHB at unplugging time and recreate
them at plugging time. pe->bus is still dereferencing the PCI bus
that was released.

This adds another PE flag (EEH_PE_PRI_BUS) to represent the validity
of pe->bus. pe->bus is updated when its first child EEH device is
online and the flag is set. Before unplugging in full hotplug for
error recovery, the flag is cleared.

Fixes: 8cdb2833 ("powerpc/eeh: Trace PCI bus from PE")
Cc: stable@vger.kernel.org #v3.11+
Reported-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: NPradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

arch/powerpc/include/asm/eeh.h

@@ -81,6 +81,7 @@ struct pci_dn;
 #define EEH_PE_KEEP		(1 << 8)	/* Keep PE on hotplug	*/
 #define EEH_PE_CFG_RESTRICTED	(1 << 9)	/* Block config on error */
 #define EEH_PE_REMOVED		(1 << 10)	/* Removed permanently	*/
+#define EEH_PE_PRI_BUS		(1 << 11)	/* Cached primary bus   */
 
 struct eeh_pe {
 	int type;			/* PE type: PHB/Bus/Device	*/

arch/powerpc/kernel/eeh_driver.c

@@ -564,6 +564,7 @@ static int eeh_reset_device(struct eeh_pe *pe, struct pci_bus *bus)
 	 */
 	eeh_pe_state_mark(pe, EEH_PE_KEEP);
 	if (bus) {
+		eeh_pe_state_clear(pe, EEH_PE_PRI_BUS);
 		pci_lock_rescan_remove();
 		pcibios_remove_pci_devices(bus);
 		pci_unlock_rescan_remove();
@@ -803,6 +804,7 @@ static void eeh_handle_normal_event(struct eeh_pe *pe)
 	 * the their PCI config any more.
 	 */
 	if (frozen_bus) {
+		eeh_pe_state_clear(pe, EEH_PE_PRI_BUS);
 		eeh_pe_dev_mode_mark(pe, EEH_DEV_REMOVED);
 
 		pci_lock_rescan_remove();
@@ -886,6 +888,7 @@ static void eeh_handle_special_event(void)
 					continue;
 
 				/* Notify all devices to be down */
+				eeh_pe_state_clear(pe, EEH_PE_PRI_BUS);
 				bus = eeh_pe_bus_get(phb_pe);
 				eeh_pe_dev_traverse(pe,
 					eeh_report_failure, NULL);

arch/powerpc/kernel/eeh_pe.c

@@ -928,7 +928,7 @@ struct pci_bus *eeh_pe_bus_get(struct eeh_pe *pe)
 		bus = pe->phb->bus;
 	} else if (pe->type & EEH_PE_BUS ||
 		   pe->type & EEH_PE_DEVICE) {
-		if (pe->bus) {
+		if (pe->state & EEH_PE_PRI_BUS) {
 			bus = pe->bus;
 			goto out;
 		}

arch/powerpc/platforms/powernv/eeh-powernv.c

@@ -444,9 +444,12 @@ static void *pnv_eeh_probe(struct pci_dn *pdn, void *data)
 	 * PCI devices of the PE are expected to be removed prior
 	 * to PE reset.
 	 */
-	if (!edev->pe->bus)
+	if (!(edev->pe->state & EEH_PE_PRI_BUS)) {
 		edev->pe->bus = pci_find_bus(hose->global_number,
 					     pdn->busno);
+		if (edev->pe->bus)
+			edev->pe->state |= EEH_PE_PRI_BUS;
+	}
 
 	/*
 	 * Enable EEH explicitly so that we will do EEH check