• V
    vlan: Correctly propagate promisc|allmulti flags in notifier. · be346ffa
    Vlad Yasevich 提交于
    Currently vlan notifier handler will try to update all vlans
    for a device when that device comes up.  A problem occurs,
    however, when the vlan device was set to promiscuous, but not
    by the user (ex: a bridge).  In that case, dev->gflags are
    not updated.  What results is that the lower device ends
    up with an extra promiscuity count.  Here are the
    backtraces that prove this:
    [62852.052179]  [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
    [62852.052186]  [<ffffffff8160bcbb>] ? _raw_spin_unlock_bh+0x1b/0x40
    [62852.052188]  [<ffffffff814fe4be>] ? dev_set_rx_mode+0x2e/0x40
    [62852.052190]  [<ffffffff814fe694>] dev_set_promiscuity+0x24/0x50
    [62852.052194]  [<ffffffffa0324795>] vlan_dev_open+0xd5/0x1f0 [8021q]
    [62852.052196]  [<ffffffff814fe58f>] __dev_open+0xbf/0x140
    [62852.052198]  [<ffffffff814fe88d>] __dev_change_flags+0x9d/0x170
    [62852.052200]  [<ffffffff814fe989>] dev_change_flags+0x29/0x60
    
    The above comes from the setting the vlan device to IFF_UP state.
    
    [62852.053569]  [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
    [62852.053571]  [<ffffffffa032459b>] ? vlan_dev_set_rx_mode+0x2b/0x30
    [8021q]
    [62852.053573]  [<ffffffff814fe8d5>] __dev_change_flags+0xe5/0x170
    [62852.053645]  [<ffffffff814fe989>] dev_change_flags+0x29/0x60
    [62852.053647]  [<ffffffffa032334a>] vlan_device_event+0x18a/0x690
    [8021q]
    [62852.053649]  [<ffffffff8161036c>] notifier_call_chain+0x4c/0x70
    [62852.053651]  [<ffffffff8109d456>] raw_notifier_call_chain+0x16/0x20
    [62852.053653]  [<ffffffff814f744d>] call_netdevice_notifiers+0x2d/0x60
    [62852.053654]  [<ffffffff814fe1a3>] __dev_notify_flags+0x33/0xa0
    [62852.053656]  [<ffffffff814fe9b2>] dev_change_flags+0x52/0x60
    [62852.053657]  [<ffffffff8150cd57>] do_setlink+0x397/0xa40
    
    And this one comes from the notification code.  What we end
    up with is a vlan with promiscuity count of 1 and and a physical
    device with a promiscuity count of 2.  They should both have
    a count 1.
    
    To resolve this issue, vlan code can use dev_get_flags() api
    which correctly masks promiscuity and allmulti flags.
    Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
    Signed-off-by: NDavid S. Miller <davem@davemloft.net>
    be346ffa
vlan.c 16.6 KB