allwinner,sunxi-pinctrl.txt

* Allwinner A1X Pin Controller

The pins controlled by sunXi pin controller are organized in banks,
each bank has 32 pins.  Each pin has 7 multiplexing functions, with
the first two functions being GPIO in and out. The configuration on
the pins includes drive strength and pull-up.

Required properties:
- compatible: Should be one of the followings (depending on you SoC):
  "allwinner,sun4i-a10-pinctrl"
  "allwinner,sun5i-a10s-pinctrl"
  "allwinner,sun5i-a13-pinctrl"
  "allwinner,sun6i-a31-pinctrl"
  "allwinner,sun6i-a31s-pinctrl"
  "allwinner,sun6i-a31-r-pinctrl"
  "allwinner,sun7i-a20-pinctrl"
  "allwinner,sun8i-a23-pinctrl"
  "allwinner,sun8i-a23-r-pinctrl"
  "allwinner,sun8i-a33-pinctrl"
  "allwinner,sun9i-a80-pinctrl"
  "allwinner,sun9i-a80-r-pinctrl"
  "allwinner,sun8i-a83t-pinctrl"
  "allwinner,sun8i-h3-pinctrl"
  "allwinner,sun8i-h3-r-pinctrl"
  "allwinner,sun50i-a64-pinctrl"
  "nextthing,gr8-pinctrl"

- reg: Should contain the register physical address and length for the
  pin controller.

- clocks: phandle to the clocks feeding the pin controller:
  - "apb": the gated APB parent clock
  - "hosc": the high frequency oscillator in the system
  - "losc": the low frequency oscillator in the system

Note: For backward compatibility reasons, the hosc and losc clocks are only
required if you need to use the optional input-debounce property. Any new
device tree should set them.

Optional properties:
  - input-debounce: Array of debouncing periods in microseconds. One period per
    irq bank found in the controller. 0 if no setup required.


Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices.

A pinctrl node should contain at least one subnodes representing the
pinctrl groups available on the machine. Each subnode will list the
pins it needs, and how they should be configured, with regard to muxer
configuration, drive strength and pullups. If one of these options is
not set, its actual value will be unspecified.

This driver supports the generic pin multiplexing and configuration
bindings. For details on each properties, you can refer to
./pinctrl-bindings.txt.

Required sub-node properties:
  - pins
  - function

Optional sub-node properties:
  - bias-disable
  - bias-pull-up
  - bias-pull-down
  - drive-strength

*** Deprecated pin configuration and multiplexing binding

Required subnode-properties:

- allwinner,pins: List of strings containing the pin name.
- allwinner,function: Function to mux the pins listed above to.

Optional subnode-properties:
- allwinner,drive: Integer. Represents the current sent to the pin
    0: 10 mA
    1: 20 mA
    2: 30 mA
    3: 40 mA
- allwinner,pull: Integer.
    0: No resistor
    1: Pull-up resistor
    2: Pull-down resistor

Examples:

pio: pinctrl@01c20800 {
	compatible = "allwinner,sun5i-a13-pinctrl";
	reg = <0x01c20800 0x400>;
	#address-cells = <1>;
	#size-cells = <0>;

	uart1_pins_a: uart1@0 {
		allwinner,pins = "PE10", "PE11";
		allwinner,function = "uart1";
		allwinner,drive = <0>;
		allwinner,pull = <0>;
	};

	uart1_pins_b: uart1@1 {
		allwinner,pins = "PG3", "PG4";
		allwinner,function = "uart1";
		allwinner,drive = <0>;
		allwinner,pull = <0>;
	};
};


GPIO and interrupt controller
-----------------------------

This hardware also acts as a GPIO controller and an interrupt
controller.

Consumers that would want to refer to one or the other (or both)
should provide through the usual *-gpios and interrupts properties a
cell with 3 arguments, first the number of the bank, then the pin
inside that bank, and finally the flags for the GPIO/interrupts.

Example:

xio: gpio@38 {
	compatible = "nxp,pcf8574a";
	reg = <0x38>;

	gpio-controller;
	#gpio-cells = <2>;

	interrupt-parent = <&pio>;
	interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>;
	interrupt-controller;
	#interrupt-cells = <2>;
};

reg_usb1_vbus: usb1-vbus {
	compatible = "regulator-fixed";
	regulator-name = "usb1-vbus";
	regulator-min-microvolt = <5000000>;
	regulator-max-microvolt = <5000000>;
	gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>;
};