Kconfig 18.1 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4 5 6 7 8 9 10
#
# For a description of the syntax of this configuration file,
# see Documentation/kbuild/kconfig-language.txt.
#

mainmenu "Linux/SuperH Kernel Configuration"

config SUPERH
	bool
	default y
P
Paul Mundt 已提交
11
	select EMBEDDED
L
Linus Torvalds 已提交
12 13 14 15 16 17 18 19 20 21 22 23 24
	help
	  The SuperH is a RISC processor targeted for use in embedded systems
	  and consumer electronics; it was also used in the Sega Dreamcast
	  gaming console.  The SuperH port has a home page at
	  <http://www.linux-sh.org/>.

config RWSEM_GENERIC_SPINLOCK
	bool
	default y

config RWSEM_XCHGADD_ALGORITHM
	bool

P
Paul Mundt 已提交
25 26 27 28
config GENERIC_BUG
	def_bool y
	depends on BUG

29 30 31 32 33 34 35 36
config GENERIC_FIND_NEXT_BIT
	bool
	default y

config GENERIC_HWEIGHT
	bool
	default y

L
Linus Torvalds 已提交
37 38 39 40 41 42 43 44 45 46 47 48
config GENERIC_HARDIRQS
	bool
	default y

config GENERIC_IRQ_PROBE
	bool
	default y

config GENERIC_CALIBRATE_DELAY
	bool
	default y

49 50 51
config GENERIC_IOMAP
	bool

52 53 54
config GENERIC_TIME
	def_bool n

55 56 57
config SYS_SUPPORTS_APM_EMULATION
	bool

58 59 60
config ARCH_MAY_HAVE_PC_FDC
	bool

61 62 63 64 65 66 67 68
config STACKTRACE_SUPPORT
	bool
	default y

config LOCKDEP_SUPPORT
	bool
	default y

69 70 71 72 73 74 75 76
config ARCH_HAS_ILOG2_U32
	bool
	default n

config ARCH_HAS_ILOG2_U64
	bool
	default n

L
Linus Torvalds 已提交
77 78 79 80
source "init/Kconfig"

menu "System type"

81 82 83
config SOLUTION_ENGINE
	bool

L
Linus Torvalds 已提交
84 85 86 87 88 89
choice
	prompt "SuperH system type"
	default SH_UNKNOWN

config SH_SOLUTION_ENGINE
	bool "SolutionEngine"
90
	select SOLUTION_ENGINE
L
Linus Torvalds 已提交
91 92 93 94
	help
	  Select SolutionEngine if configuring for a Hitachi SH7709
	  or SH7750 evaluation board.

95 96 97 98 99 100 101 102
config SH_7722_SOLUTION_ENGINE
	bool "SolutionEngine7722"
	select SOLUTION_ENGINE
	select CPU_SUBTYPE_SH7722
	help
	  Select 7722 SolutionEngine if configuring for a Hitachi SH772
	  evaluation board.

L
Linus Torvalds 已提交
103 104
config SH_7751_SOLUTION_ENGINE
	bool "SolutionEngine7751"
105
	select SOLUTION_ENGINE
106
	select CPU_SUBTYPE_SH7751
L
Linus Torvalds 已提交
107 108 109
	help
	  Select 7751 SolutionEngine if configuring for a Hitachi SH7751
	  evaluation board.
110 111 112 113 114 115 116 117
	  
config SH_7780_SOLUTION_ENGINE
	bool "SolutionEngine7780"
	select SOLUTION_ENGINE
	select CPU_SUBTYPE_SH7780
	help
	  Select 7780 SolutionEngine if configuring for a Renesas SH7780
	  evaluation board.
L
Linus Torvalds 已提交
118 119 120

config SH_7300_SOLUTION_ENGINE
	bool "SolutionEngine7300"
121
	select SOLUTION_ENGINE
122
	select CPU_SUBTYPE_SH7300
L
Linus Torvalds 已提交
123
	help
124 125 126 127 128 129 130 131 132 133
	  Select 7300 SolutionEngine if configuring for a Hitachi
	  SH7300(SH-Mobile V) evaluation board.

config SH_7343_SOLUTION_ENGINE
	bool "SolutionEngine7343"
	select SOLUTION_ENGINE
	select CPU_SUBTYPE_SH7343
	help
	  Select 7343 SolutionEngine if configuring for a Hitachi
	  SH7343 (SH-Mobile 3AS) evaluation board.
L
Linus Torvalds 已提交
134 135 136

config SH_73180_SOLUTION_ENGINE
       bool "SolutionEngine73180"
137 138 139 140 141
	select SOLUTION_ENGINE
	select CPU_SUBTYPE_SH73180
	help
	  Select 73180 SolutionEngine if configuring for a Hitachi
	  SH73180(SH-Mobile 3) evaluation board.
L
Linus Torvalds 已提交
142 143 144

config SH_7751_SYSTEMH
	bool "SystemH7751R"
145
	select CPU_SUBTYPE_SH7751R
L
Linus Torvalds 已提交
146 147 148 149
	help
	  Select SystemH if you are configuring for a Renesas SystemH
	  7751R evaluation board.

150 151
config SH_HP6XX
	bool "HP6XX"
152
	select SYS_SUPPORTS_APM_EMULATION
L
Linus Torvalds 已提交
153
	help
154
	  Select HP6XX if configuring for a HP jornada HP6xx.
L
Linus Torvalds 已提交
155 156 157 158 159
	  More information (hardware only) at
	  <http://www.hp.com/jornada/>.

config SH_SATURN
	bool "Saturn"
160
	select CPU_SUBTYPE_SH7604
L
Linus Torvalds 已提交
161 162 163 164 165
	help
	  Select Saturn if configuring for a SEGA Saturn.

config SH_DREAMCAST
	bool "Dreamcast"
166
	select CPU_SUBTYPE_SH7091
L
Linus Torvalds 已提交
167 168 169 170 171 172 173
	help
	  Select Dreamcast if configuring for a SEGA Dreamcast.
	  More information at
	  <http://www.m17n.org/linux-sh/dreamcast/>.  There is a
	  Dreamcast project is at <http://linuxdc.sourceforge.net/>.

config SH_MPC1211
174 175 176 177 178
	bool "Interface MPC1211"
	help
	  CTP/PCI-SH02 is a CPU module computer that is produced
	  by Interface Corporation.
	  More information at <http://www.interface.co.jp>
L
Linus Torvalds 已提交
179 180

config SH_SH03
181
	bool "Interface CTP/PCI-SH03"
L
Linus Torvalds 已提交
182
	help
183
	  CTP/PCI-SH03 is a CPU module computer that is produced
L
Linus Torvalds 已提交
184 185 186 187 188
	  by Interface Corporation.
	  More information at <http://www.interface.co.jp>

config SH_SECUREEDGE5410
	bool "SecureEdge5410"
189
	select CPU_SUBTYPE_SH7751R
L
Linus Torvalds 已提交
190 191 192 193 194 195 196
	help
	  Select SecureEdge5410 if configuring for a SnapGear SH board.
	  This includes both the OEM SecureEdge products as well as the
	  SME product line.

config SH_HS7751RVOIP
	bool "HS7751RVOIP"
197
	select CPU_SUBTYPE_SH7751R
L
Linus Torvalds 已提交
198 199 200 201
	help
	  Select HS7751RVOIP if configuring for a Renesas Technology
	  Sales VoIP board.

P
Paul Mundt 已提交
202 203 204 205 206 207 208
config SH_7710VOIPGW
	bool "SH7710-VOIP-GW"
	select CPU_SUBTYPE_SH7710
	help
	  Select this option to build a kernel for the SH7710 based
	  VOIP GW.

L
Linus Torvalds 已提交
209 210
config SH_RTS7751R2D
	bool "RTS7751R2D"
211
	select CPU_SUBTYPE_SH7751R
L
Linus Torvalds 已提交
212 213 214 215
	help
	  Select RTS7751R2D if configuring for a Renesas Technology
	  Sales SH-Graphics board.

216 217
config SH_HIGHLANDER
	bool "Highlander"
218

L
Linus Torvalds 已提交
219 220
config SH_EDOSK7705
	bool "EDOSK7705"
221
	select CPU_SUBTYPE_SH7705
L
Linus Torvalds 已提交
222 223 224

config SH_SH4202_MICRODEV
	bool "SH4-202 MicroDev"
225
	select CPU_SUBTYPE_SH4_202
L
Linus Torvalds 已提交
226 227 228 229
	help
	  Select SH4-202 MicroDev if configuring for a SuperH MicroDev board
	  with an SH4-202 CPU.

230 231 232 233 234 235 236 237 238 239 240 241 242
config SH_LANDISK
	bool "LANDISK"
	select CPU_SUBTYPE_SH7751R
	help
	  I-O DATA DEVICE, INC. "LANDISK Series" support.

config SH_TITAN
	bool "TITAN"
	select CPU_SUBTYPE_SH7751R
	help
	  Select Titan if you are configuring for a Nimble Microsystems
	  NetEngine NP51R.

T
Takashi YOSHII 已提交
243 244 245 246
config SH_SHMIN
	bool "SHMIN"
	select CPU_SUBTYPE_SH7706
	help
M
Matt LaPlante 已提交
247
	  Select SHMIN if configuring for the SHMIN board.
T
Takashi YOSHII 已提交
248

249 250 251 252 253 254 255 256 257 258 259 260 261
config SH_7206_SOLUTION_ENGINE
	bool "SolutionEngine7206"
	select CPU_SUBTYPE_SH7206
	help
	  Select 7206 SolutionEngine if configuring for a Hitachi SH7206
	  evaluation board.

config SH_7619_SOLUTION_ENGINE
	bool "SolutionEngine7619"
	select CPU_SUBTYPE_SH7619
	help
	  Select 7619 SolutionEngine if configuring for a Hitachi SH7619
	  evaluation board.
N
Nobuhiro Iwamatsu 已提交
262 263 264 265 266 267
	
config SH_LBOX_RE2
	bool "L-BOX RE2"
	select CPU_SUBTYPE_SH7751R
	help
	  Select L-BOX RE2 if configuring for the NTT COMWARE L-BOX RE2.
268

L
Linus Torvalds 已提交
269 270 271 272 273 274 275 276 277 278 279 280 281 282
config SH_UNKNOWN
	bool "BareCPU"
	help
	  "Bare CPU" aka "unknown" means an SH-based system which is not one
	  of the specific ones mentioned above, which means you need to enter
	  all sorts of stuff like CONFIG_MEMORY_START because the config
	  system doesn't already know what it is.  You get a machine vector
	  without any platform-specific code in it, so things like the RTC may
	  not work.

	  This option is for the early stages of porting to a new machine.

endchoice

283 284 285 286
source "arch/sh/boards/renesas/hs7751rvoip/Kconfig"
source "arch/sh/boards/renesas/rts7751r2d/Kconfig"
source "arch/sh/boards/renesas/r7780rp/Kconfig"

287
source "arch/sh/mm/Kconfig"
L
Linus Torvalds 已提交
288 289 290

config CF_ENABLER
	bool "Compact Flash Enabler support"
P
Paul Mundt 已提交
291
	depends on SH_SOLUTION_ENGINE || SH_UNKNOWN || SH_SH03
L
Linus Torvalds 已提交
292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318
	---help---
	  Compact Flash is a small, removable mass storage device introduced
	  in 1994 originally as a PCMCIA device.  If you say `Y' here, you
	  compile in support for Compact Flash devices directly connected to
	  a SuperH processor.  A Compact Flash FAQ is available at
	  <http://www.compactflash.org/faqs/faq.htm>.

	  If your board has "Directly Connected" CompactFlash at area 5 or 6,
	  you may want to enable this option.  Then, you can use CF as
	  primary IDE drive (only tested for SanDisk).

	  If in doubt, select 'N'.

choice
	prompt "Compact Flash Connection Area"
	depends on CF_ENABLER
	default CF_AREA6

config CF_AREA5
	bool "Area5"
	help
	  If your board has "Directly Connected" CompactFlash, You should
	  select the area where your CF is connected to.

	  - "Area5" if CompactFlash is connected to Area 5 (0x14000000)
	  - "Area6" if it is connected to Area 6 (0x18000000)

P
Paul Mundt 已提交
319
	  "Area6" will work for most boards.
L
Linus Torvalds 已提交
320 321 322 323 324 325 326 327 328 329 330 331

config CF_AREA6
	bool "Area6"

endchoice

config CF_BASE_ADDR
	hex
	depends on CF_ENABLER
	default "0xb8000000" if CF_AREA6
	default "0xb4000000" if CF_AREA5

332 333
menu "Processor features"

334 335 336
choice
	prompt "Endianess selection" 
	default CPU_LITTLE_ENDIAN
337 338
	help
	  Some SuperH machines can be configured for either little or big
339 340 341 342 343 344 345 346 347
	  endian byte order. These modes require different kernels.

config CPU_LITTLE_ENDIAN
	bool "Little Endian"

config CPU_BIG_ENDIAN
	bool "Big Endian"

endchoice
348

L
Linus Torvalds 已提交
349 350 351 352 353 354 355 356 357 358
config SH_FPU
	bool "FPU support"
	depends on !CPU_SH3
	default y
	help
	  Selecting this option will enable support for SH processors that
	  have FPU units (ie, SH77xx).

	  This option must be set in order to enable the FPU.

T
Takashi YOSHII 已提交
359 360 361 362 363 364 365 366 367
config SH_FPU_EMU
	bool "FPU emulation support"
	depends on !SH_FPU && EXPERIMENTAL
	default n
	help
	  Selecting this option will enable support for software FPU emulation.
	  Most SH-3 users will want to say Y here, whereas most SH-4 users will
	  want to say N.

L
Linus Torvalds 已提交
368 369
config SH_DSP
	bool "DSP support"
370 371
	default y if SH4AL_DSP || !CPU_SH4
	default n
L
Linus Torvalds 已提交
372 373
	help
	  Selecting this option will enable support for SH processors that
374
	  have DSP units (ie, SH2-DSP, SH3-DSP, and SH4AL-DSP).
L
Linus Torvalds 已提交
375 376 377 378 379 380 381 382 383 384 385 386 387

	  This option must be set in order to enable the DSP.

config SH_ADC
	bool "ADC support"
	depends on CPU_SH3
	default y
	help
	  Selecting this option will allow the Linux kernel to use SH3 on-chip
	  ADC module.

	  If unsure, say N.

388 389 390 391 392 393 394
config SH_STORE_QUEUES
	bool "Support for Store Queues"
	depends on CPU_SH4
	help
	  Selecting this option will enable an in-kernel API for manipulating
	  the store queues integrated in the SH-4 processors.

395 396 397 398 399 400 401 402 403 404
config SPECULATIVE_EXECUTION
	bool "Speculative subroutine return"
	depends on CPU_SUBTYPE_SH7780 && EXPERIMENTAL
	help
	  This enables support for a speculative instruction fetch for
	  subroutine return. There are various pitfalls associated with
	  this, as outlined in the SH7780 hardware manual.

	  If unsure, say N.

405
config CPU_HAS_INTEVT
L
Linus Torvalds 已提交
406 407
	bool

408 409
config CPU_HAS_PINT_IRQ
	bool
L
Linus Torvalds 已提交
410

P
Paul Mundt 已提交
411 412 413
config CPU_HAS_MASKREG_IRQ
	bool

414 415
config CPU_HAS_INTC2_IRQ
	bool
416

417 418 419
config CPU_HAS_IPR_IRQ
	bool

420 421 422 423
config CPU_HAS_SR_RB
	bool "CPU has SR.RB"
	depends on CPU_SH3 || CPU_SH4
	default y
L
Linus Torvalds 已提交
424
	help
425 426 427
	  This will enable the use of SR.RB register bank usage. Processors
	  that are lacking this bit must have another method in place for
	  accomplishing what is taken care of by the banked registers.
L
Linus Torvalds 已提交
428

429 430
	  See <file:Documentation/sh/register-banks.txt> for further
	  information on SR.RB and register banking in the kernel in general.
L
Linus Torvalds 已提交
431

432 433 434
config CPU_HAS_PTEA
	bool

435
endmenu
L
Linus Torvalds 已提交
436

437 438 439
menu "Timer and clock configuration"

if !GENERIC_TIME
L
Linus Torvalds 已提交
440

441 442
config SH_TMU
	bool "TMU timer support"
443
	depends on CPU_SH3 || CPU_SH4
L
Linus Torvalds 已提交
444 445
	default y
	help
446
	  This enables the use of the TMU as the system timer.
L
Linus Torvalds 已提交
447

448 449 450 451 452 453 454 455 456 457 458 459 460 461
config SH_CMT
	bool "CMT timer support"
	depends on CPU_SH2
	default y
	help
	  This enables the use of the CMT as the system timer.

config SH_MTU2
	bool "MTU2 timer support"
	depends on CPU_SH2A
	default n
	help
	  This enables the use of the MTU2 as the system timer.

462
endif
463

P
Paul Mundt 已提交
464 465
config SH_TIMER_IRQ
	int
466
	default "28" if CPU_SUBTYPE_SH7780 || CPU_SUBTYPE_SH7785
P
Paul Mundt 已提交
467 468 469 470
	default "86" if CPU_SUBTYPE_SH7619
	default "140" if CPU_SUBTYPE_SH7206
	default "16"

P
Paul Mundt 已提交
471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488
config NO_IDLE_HZ
	bool "Dynamic tick timer"
	help
	  Select this option if you want to disable continuous timer ticks
	  and have them programmed to occur as required. This option saves
	  power as the system can remain in idle state for longer.

	  By default dynamic tick is disabled during the boot, and can be
	  manually enabled with:

	    echo 1 > /sys/devices/system/timer/timer0/dyn_tick

	  Alternatively, if you want dynamic tick automatically enabled
	  during boot, pass "dyntick=enable" via the kernel command string.

	  Please note that dynamic tick may affect the accuracy of
	  timekeeping on some platforms depending on the implementation.

489 490
config SH_PCLK_FREQ
	int "Peripheral clock frequency (in Hz)"
491 492 493 494 495
	default "27000000" if CPU_SUBTYPE_SH73180 || CPU_SUBTYPE_SH7343
	default "31250000" if CPU_SUBTYPE_SH7619
	default "33333333" if CPU_SUBTYPE_SH7300 || CPU_SUBTYPE_SH7770 || \
			      CPU_SUBTYPE_SH7760 || CPU_SUBTYPE_SH7705 || \
			      CPU_SUBTYPE_SH7206
496 497
	default "50000000" if CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7780 || \
			      CPU_SUBTYPE_SH7785
498 499
	default "60000000" if CPU_SUBTYPE_SH7751
	default "66000000" if CPU_SUBTYPE_SH4_202
L
Linus Torvalds 已提交
500
	help
501 502 503
	  This option is used to specify the peripheral clock frequency.
	  This is necessary for determining the reference clock value on
	  platforms lacking an RTC.
L
Linus Torvalds 已提交
504

505 506
config SH_CLK_MD
	int "CPU Mode Pin Setting"
507
	default 0
508 509
	depends on CPU_SUBTYPE_SH7619 || CPU_SUBTYPE_SH7206
	help
510
	  MD2 - MD0 pin setting.
511

512 513
endmenu

514 515 516
menu "CPU Frequency scaling"

source "drivers/cpufreq/Kconfig"
L
Linus Torvalds 已提交
517

518 519 520 521
config SH_CPU_FREQ
	tristate "SuperH CPU Frequency driver"
	depends on CPU_FREQ
	select CPU_FREQ_TABLE
L
Linus Torvalds 已提交
522
	help
523 524
	  This adds the cpufreq driver for SuperH. At present, only
	  the SH-4 is supported.
L
Linus Torvalds 已提交
525

526
	  For details, take a look at <file:Documentation/cpu-freq>.
L
Linus Torvalds 已提交
527 528 529

	  If unsure, say N.

530 531
endmenu

P
Paul Mundt 已提交
532 533
source "arch/sh/drivers/Kconfig"

534
endmenu
L
Linus Torvalds 已提交
535

536 537
config ISA_DMA_API
	bool
538
	depends on SH_MPC1211
539
	default y
L
Linus Torvalds 已提交
540

541 542
menu "Kernel features"

P
Paul Mundt 已提交
543 544
source kernel/Kconfig.hz

545 546 547
config KEXEC
	bool "kexec system call (EXPERIMENTAL)"
	depends on EXPERIMENTAL
L
Linus Torvalds 已提交
548
	help
549 550
	  kexec is a system call that implements the ability to shutdown your
	  current kernel, and to start another kernel.  It is like a reboot
551
	  but it is independent of the system firmware.  And like a reboot
552 553
	  you can start any kernel with it, not just Linux.

554
	  The name comes from the similarity to the exec system call.
555 556 557 558 559 560 561

	  It is an ongoing process to be certain the hardware in a machine
	  is properly shutdown, so do not be surprised if this code does not
	  initially work for you.  It may help to enable device hotplugging
	  support.  As of this writing the exact hardware interface is
	  strongly in flux, so no good recommendation can be made.

P
Paul Mundt 已提交
562 563 564 565 566 567 568 569 570 571 572 573 574 575
config CRASH_DUMP
	bool "kernel crash dumps (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	help
	  Generate crash dump after being started by kexec.
	  This should be normally only set in special crash dump kernels
	  which are loaded in the main kernel with kexec-tools into
	  a specially reserved region and then later executed after
	  a crash by kdump/kexec. The crash dump kernel must be compiled
	  to a memory address not used by the main kernel using
	  MEMORY_START.

	  For more details see Documentation/kdump/kdump.txt

L
Linus Torvalds 已提交
576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610
config SMP
	bool "Symmetric multi-processing support"
	---help---
	  This enables support for systems with more than one CPU. If you have
	  a system with only one CPU, like most personal computers, say N. If
	  you have a system with more than one CPU, say Y.

	  If you say N here, the kernel will run on single and multiprocessor
	  machines, but will use only one CPU of a multiprocessor machine. If
	  you say Y here, the kernel will run on many, but not all,
	  singleprocessor machines. On a singleprocessor machine, the kernel
	  will run faster if you say N here.

	  People using multiprocessor machines who say Y here should also say
	  Y to "Enhanced Real Time Clock Support", below.

	  See also the <file:Documentation/smp.txt>,
	  <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available
	  at <http://www.tldp.org/docs.html#howto>.

	  If you don't know what to do here, say N.

config NR_CPUS
	int "Maximum number of CPUs (2-32)"
	range 2 32
	depends on SMP
	default "2"
	help
	  This allows you to specify the maximum number of CPUs which this
	  kernel will support.  The maximum supported value is 32 and the
	  minimum value which makes sense is 2.

	  This is purely to save memory - each supported CPU adds
	  approximately eight kilobytes to the kernel image.

P
Paul Mundt 已提交
611 612
source "kernel/Kconfig.preempt"

Y
Yasunori Goto 已提交
613 614 615 616 617
config NODES_SHIFT
	int
	default "1"
	depends on NEED_MULTIPLE_NODES

618
endmenu
L
Linus Torvalds 已提交
619

620
menu "Boot options"
L
Linus Torvalds 已提交
621

622 623 624
config ZERO_PAGE_OFFSET
	hex "Zero page offset"
	default "0x00004000" if SH_MPC1211 || SH_SH03
625 626
	default "0x00010000" if PAGE_SIZE_64KB
	default "0x00002000" if PAGE_SIZE_8KB
627
	default "0x00001000"
L
Linus Torvalds 已提交
628
	help
629
	  This sets the default offset of zero page.
L
Linus Torvalds 已提交
630

631 632 633 634 635 636 637
config BOOT_LINK_OFFSET
	hex "Link address offset for booting"
	default "0x00800000"
	help
	  This option allows you to set the link address offset of the zImage.
	  This can be useful if you are on a board which has a small amount of
	  memory.
L
Linus Torvalds 已提交
638

639 640 641 642 643 644 645
config UBC_WAKEUP
	bool "Wakeup UBC on startup"
	help
	  Selecting this option will wakeup the User Break Controller (UBC) on
	  startup. Although the UBC is left in an awake state when the processor
	  comes up, some boot loaders misbehave by putting the UBC to sleep in a
	  power saving state, which causes issues with things like ptrace().
L
Linus Torvalds 已提交
646

647
	  If unsure, say N.
L
Linus Torvalds 已提交
648

649 650
config CMDLINE_BOOL
	bool "Default bootloader kernel arguments"
L
Linus Torvalds 已提交
651

652 653 654 655
config CMDLINE
	string "Initial kernel command string"
	depends on CMDLINE_BOOL
	default "console=ttySC1,115200"
L
Linus Torvalds 已提交
656 657 658

endmenu

659
menu "Bus options"
L
Linus Torvalds 已提交
660 661 662 663 664 665 666 667 668 669

# Even on SuperH devices which don't have an ISA bus,
# this variable helps the PCMCIA modules handle
# IRQ requesting properly -- Greg Banks.
#
# Though we're generally not interested in it when
# we're not using PCMCIA, so we make it dependent on
# PCMCIA outright. -- PFM.
config ISA
	bool
670
	default y if PCMCIA
L
Linus Torvalds 已提交
671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703
	help
	  Find out whether you have ISA slots on your motherboard.  ISA is the
	  name of a bus system, i.e. the way the CPU talks to the other stuff
	  inside your box.  Other bus systems are PCI, EISA, MicroChannel
	  (MCA) or VESA.  ISA is an older system, now being displaced by PCI;
	  newer boards don't support it.  If you have ISA, say Y, otherwise N.

config EISA
	bool
	---help---
	  The Extended Industry Standard Architecture (EISA) bus was
	  developed as an open alternative to the IBM MicroChannel bus.

	  The EISA bus provided some of the features of the IBM MicroChannel
	  bus while maintaining backward compatibility with cards made for
	  the older ISA bus.  The EISA bus saw limited use between 1988 and
	  1995 when it was made obsolete by the PCI bus.

	  Say Y here if you are building a kernel for an EISA-based machine.

	  Otherwise, say N.

config MCA
	bool
	help
	  MicroChannel Architecture is found in some IBM PS/2 machines and
	  laptops.  It is a bus system similar to PCI or ISA. See
	  <file:Documentation/mca.txt> (and especially the web page given
	  there) before attempting to build an MCA bus kernel.

config SBUS
	bool

704 705 706
config SUPERHYWAY
	tristate "SuperHyway Bus support"
	depends on CPU_SUBTYPE_SH4_202
L
Linus Torvalds 已提交
707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723

source "arch/sh/drivers/pci/Kconfig"

source "drivers/pci/Kconfig"

source "drivers/pcmcia/Kconfig"

source "drivers/pci/hotplug/Kconfig"

endmenu

menu "Executable file formats"

source "fs/Kconfig.binfmt"

endmenu

A
Andriy Skulysh 已提交
724 725 726 727 728 729 730
menu "Power management options (EXPERIMENTAL)"
depends on EXPERIMENTAL

source kernel/power/Kconfig

endmenu

731 732
source "net/Kconfig"

L
Linus Torvalds 已提交
733 734 735 736 737 738 739 740 741 742 743 744 745
source "drivers/Kconfig"

source "fs/Kconfig"

source "arch/sh/oprofile/Kconfig"

source "arch/sh/Kconfig.debug"

source "security/Kconfig"

source "crypto/Kconfig"

source "lib/Kconfig"