saa7115.c

/* saa711x - Philips SAA711x video decoder driver
 * This driver can work with saa7111, saa7111a, saa7113, saa7114,
 *			     saa7115 and saa7118.
 *
 * Based on saa7114 driver by Maxim Yevtyushkin, which is based on
 * the saa7111 driver by Dave Perks.
 *
 * Copyright (C) 1998 Dave Perks <dperks@ibm.net>
 * Copyright (C) 2002 Maxim Yevtyushkin <max@linuxmedialabs.com>
 *
 * Slight changes for video timing and attachment output by
 * Wolfgang Scherr <scherr@net4you.net>
 *
 * Moved over to the linux >= 2.4.x i2c protocol (1/1/2003)
 * by Ronald Bultje <rbultje@ronald.bitfreak.net>
 *
 * Added saa7115 support by Kevin Thayer <nufan_wfk at yahoo.com>
 * (2/17/2003)
 *
 * VBI support (2004) and cleanups (2005) by Hans Verkuil <hverkuil@xs4all.nl>
 *
 * Copyright (c) 2005-2006 Mauro Carvalho Chehab <mchehab@infradead.org>
 *	SAA7111, SAA7113 and SAA7118 support
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version 2
 * of the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA.
 */

#include "saa711x_regs.h"

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/i2c.h>
#include <linux/videodev2.h>
#include <media/v4l2-common.h>
#include <media/saa7115.h>
#include <asm/div64.h>

MODULE_DESCRIPTION("Philips SAA7111/SAA7113/SAA7114/SAA7115/SAA7118 video decoder driver");
MODULE_AUTHOR(  "Maxim Yevtyushkin, Kevin Thayer, Chris Kennedy, "
		"Hans Verkuil, Mauro Carvalho Chehab");
MODULE_LICENSE("GPL");

static int debug = 0;
module_param(debug, bool, 0644);

MODULE_PARM_DESC(debug, "Debug level (0-1)");

static unsigned short normal_i2c[] = {
		0x4a >> 1, 0x48 >> 1,	/* SAA7111, SAA7111A and SAA7113 */
		0x42 >> 1, 0x40 >> 1,	/* SAA7114, SAA7115 and SAA7118 */
		I2C_CLIENT_END };


I2C_CLIENT_INSMOD;

struct saa711x_state {
	v4l2_std_id std;
	int input;
	int enable;
	int radio;
	int bright;
	int contrast;
	int hue;
	int sat;
	enum v4l2_chip_ident ident;
	u32 audclk_freq;
	u32 crystal_freq;
	u8 ucgc;
	u8 cgcdiv;
	u8 apll;
};

/* ----------------------------------------------------------------------- */

static inline int saa711x_write(struct i2c_client *client, u8 reg, u8 value)
{
	return i2c_smbus_write_byte_data(client, reg, value);
}

/* Sanity routine to check if a register is present */
static int saa711x_has_reg(const int id, const u8 reg)
{
	switch (id) {
	case V4L2_IDENT_SAA7111:
		if (reg>0x1f || reg==1 || reg==0x0f || reg==0x14 || reg==0x18
				       || reg==0x19 || reg==0x1d || reg==0x1e)
			return 0;
	case V4L2_IDENT_SAA7113:
		if (reg>0x62 || reg==0x14 || (reg>=0x18 && reg<=0x1e) ||
				    (reg>=0x20 && reg<=0x3f) ||reg==0x5f )
			return 0;
	case V4L2_IDENT_SAA7114:
		if (reg>=0xf0 || (reg>=0x1a && reg<=0x1e) ||
				  (reg>=0x20 && reg<=0x2f) ||
				  (reg>=0x63 && reg<=0x7f) )
			return 0;
	case V4L2_IDENT_SAA7115:
		if ((reg>=0x20 && reg<=0x2f) || (reg==0x5c) ||
				(reg>=0xfc && reg<=0xfe) )
			return 0;
	case V4L2_IDENT_SAA7118:
		if (reg>=0xf0 || (reg>=0x1a && reg<=0x1d) ||
					(reg>=0x63 && reg<=0x6f) )
			return 0;
	}

	/* Those registers are reserved for all family */
	if (unlikely((reg>=0x20 && reg<=0x22) ||
			(reg>=0x26 && reg<=0x28) ||
			(reg>=0x3b && reg<=0x3f) || (reg==0x5f) ||
			(reg>=0x63 && reg<=0x6f) ) )
		return 0;

	return 1;
}

static int saa711x_writeregs(struct i2c_client *client, const unsigned char *regs)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	unsigned char reg, data;

	while (*regs != 0x00) {
		reg = *(regs++);
		data = *(regs++);

		/* According with datasheets, reserved regs should be
		   filled with 0 - seems better not to touch on they */
		if (saa711x_has_reg(state->ident,reg)) {
			if (saa711x_write(client, reg, data) < 0)
				return -1;
		}
	}
	return 0;
}

static inline int saa711x_read(struct i2c_client *client, u8 reg)
{
	return i2c_smbus_read_byte_data(client, reg);
}

/* ----------------------------------------------------------------------- */

/* SAA7111 initialization table */
static const unsigned char saa7111_init_auto_input[] = {
	R_01_INC_DELAY, 0x00,		/* reserved */

	/*front end */
	R_02_INPUT_CNTL_1, 0xd0,	/* FUSE=3, GUDL=2, MODE=0 */
	R_03_INPUT_CNTL_2, 0x23,	/* HLNRS=0, VBSL=1, WPOFF=0, HOLDG=0,
					 * GAFIX=0, GAI1=256, GAI2=256 */
	R_04_INPUT_CNTL_3, 0x00,	/* GAI1=256 */
	R_05_INPUT_CNTL_4, 0x00,	/* GAI2=256 */

	/* decoder */
	R_06_H_SYNC_START, 0xf3,	/* HSB at  13(50Hz) /  17(60Hz)
					 * pixels after end of last line */
	R_07_H_SYNC_STOP, 0xe8,		/* HSS seems to be needed to
					 * work with NTSC, too */
	R_08_SYNC_CNTL, 0xc8,		/* AUFD=1, FSEL=1, EXFIL=0,
					 * VTRC=1, HPLL=0, VNOI=0 */
	R_09_LUMA_CNTL, 0x01,		/* BYPS=0, PREF=0, BPSS=0,
					 * VBLB=0, UPTCV=0, APER=1 */
	R_0A_LUMA_BRIGHT_CNTL, 0x80,
	R_0B_LUMA_CONTRAST_CNTL, 0x47,	/* 0b - CONT=1.109 */
	R_0C_CHROMA_SAT_CNTL, 0x40,
	R_0D_CHROMA_HUE_CNTL, 0x00,
	R_0E_CHROMA_CNTL_1, 0x01,	/* 0e - CDTO=0, CSTD=0, DCCF=0,
					 * FCTC=0, CHBW=1 */
	R_0F_CHROMA_GAIN_CNTL, 0x00,	/* reserved */
	R_10_CHROMA_CNTL_2, 0x48,	/* 10 - OFTS=1, HDEL=0, VRLN=1, YDEL=0 */
	R_11_MODE_DELAY_CNTL, 0x1c,	/* 11 - GPSW=0, CM99=0, FECO=0, COMPO=1,
					 * OEYC=1, OEHV=1, VIPB=0, COLO=0 */
	R_12_RT_SIGNAL_CNTL, 0x00,	/* 12 - output control 2 */
	R_13_RT_X_PORT_OUT_CNTL, 0x00,	/* 13 - output control 3 */
	R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
	R_15_VGATE_START_FID_CHG, 0x00,
	R_16_VGATE_STOP, 0x00,
	R_17_MISC_VGATE_CONF_AND_MSB, 0x00,

	0x00, 0x00
};

/* SAA7113 init codes */
static const unsigned char saa7113_init_auto_input[] = {
	R_01_INC_DELAY, 0x08,
	R_02_INPUT_CNTL_1, 0xc2,
	R_03_INPUT_CNTL_2, 0x30,
	R_04_INPUT_CNTL_3, 0x00,
	R_05_INPUT_CNTL_4, 0x00,
	R_06_H_SYNC_START, 0x89,
	R_07_H_SYNC_STOP, 0x0d,
	R_08_SYNC_CNTL, 0x88,
	R_09_LUMA_CNTL, 0x01,
	R_0A_LUMA_BRIGHT_CNTL, 0x80,
	R_0B_LUMA_CONTRAST_CNTL, 0x47,
	R_0C_CHROMA_SAT_CNTL, 0x40,
	R_0D_CHROMA_HUE_CNTL, 0x00,
	R_0E_CHROMA_CNTL_1, 0x01,
	R_0F_CHROMA_GAIN_CNTL, 0x2a,
	R_10_CHROMA_CNTL_2, 0x08,
	R_11_MODE_DELAY_CNTL, 0x0c,
	R_12_RT_SIGNAL_CNTL, 0x07,
	R_13_RT_X_PORT_OUT_CNTL, 0x00,
	R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
	R_15_VGATE_START_FID_CHG, 0x00,
	R_16_VGATE_STOP, 0x00,
	R_17_MISC_VGATE_CONF_AND_MSB, 0x00,

	0x00, 0x00
};

/* If a value differs from the Hauppauge driver values, then the comment starts with
   'was 0xXX' to denote the Hauppauge value. Otherwise the value is identical to what the
   Hauppauge driver sets. */

/* SAA7114 and SAA7115 initialization table */
static const unsigned char saa7115_init_auto_input[] = {
		/* Front-End Part */
	R_01_INC_DELAY, 0x48,			/* white peak control disabled */
	R_03_INPUT_CNTL_2, 0x20,		/* was 0x30. 0x20: long vertical blanking */
	R_04_INPUT_CNTL_3, 0x90,		/* analog gain set to 0 */
	R_05_INPUT_CNTL_4, 0x90,		/* analog gain set to 0 */
		/* Decoder Part */
	R_06_H_SYNC_START, 0xeb,		/* horiz sync begin = -21 */
	R_07_H_SYNC_STOP, 0xe0,			/* horiz sync stop = -17 */
	R_0A_LUMA_BRIGHT_CNTL, 0x80,		/* was 0x88. decoder brightness, 0x80 is itu standard */
	R_0B_LUMA_CONTRAST_CNTL, 0x44,		/* was 0x48. decoder contrast, 0x44 is itu standard */
	R_0C_CHROMA_SAT_CNTL, 0x40,		/* was 0x47. decoder saturation, 0x40 is itu standard */
	R_0D_CHROMA_HUE_CNTL, 0x00,
	R_0F_CHROMA_GAIN_CNTL, 0x00,		/* use automatic gain  */
	R_10_CHROMA_CNTL_2, 0x06,		/* chroma: active adaptive combfilter */
	R_11_MODE_DELAY_CNTL, 0x00,
	R_12_RT_SIGNAL_CNTL, 0x9d,		/* RTS0 output control: VGATE */
	R_13_RT_X_PORT_OUT_CNTL, 0x80,		/* ITU656 standard mode, RTCO output enable RTCE */
	R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
	R_18_RAW_DATA_GAIN_CNTL, 0x40,		/* gain 0x00 = nominal */
	R_19_RAW_DATA_OFF_CNTL, 0x80,
	R_1A_COLOR_KILL_LVL_CNTL, 0x77,		/* recommended value */
	R_1B_MISC_TVVCRDET, 0x42,		/* recommended value */
	R_1C_ENHAN_COMB_CTRL1, 0xa9,		/* recommended value */
	R_1D_ENHAN_COMB_CTRL2, 0x01,		/* recommended value */

		/* Power Device Control */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,	/* reset device */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,	/* set device programmed, all in operational mode */
	0x00, 0x00
};

/* Used to reset saa7113, saa7114 and saa7115 */
static const unsigned char saa7115_cfg_reset_scaler[] = {
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x00,	/* disable I-port output */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,		/* activate scaler */
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x01,	/* enable I-port output */
	0x00, 0x00
};

/* ============== SAA7715 VIDEO templates =============  */

static const unsigned char saa7115_cfg_60hz_video[] = {
	R_80_GLOBAL_CNTL_1, 0x00,			/* reset tasks */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler */

	R_15_VGATE_START_FID_CHG, 0x03,
	R_16_VGATE_STOP, 0x11,
	R_17_MISC_VGATE_CONF_AND_MSB, 0x9c,

	R_08_SYNC_CNTL, 0x68,			/* 0xBO: auto detection, 0x68 = NTSC */
	R_0E_CHROMA_CNTL_1, 0x07,		/* video autodetection is on */

	R_5A_V_OFF_FOR_SLICER, 0x06,		/* standard 60hz value for ITU656 line counting */

	/* Task A */
	R_90_A_TASK_HANDLING_CNTL, 0x80,
	R_91_A_X_PORT_FORMATS_AND_CONF, 0x48,
	R_92_A_X_PORT_INPUT_REFERENCE_SIGNAL, 0x40,
	R_93_A_I_PORT_OUTPUT_FORMATS_AND_CONF, 0x84,

	/* hoffset low (input), 0x0002 is minimum */
	R_94_A_HORIZ_INPUT_WINDOW_START, 0x01,
	R_95_A_HORIZ_INPUT_WINDOW_START_MSB, 0x00,

	/* hsize low (input), 0x02d0 = 720 */
	R_96_A_HORIZ_INPUT_WINDOW_LENGTH, 0xd0,
	R_97_A_HORIZ_INPUT_WINDOW_LENGTH_MSB, 0x02,

	R_98_A_VERT_INPUT_WINDOW_START, 0x05,
	R_99_A_VERT_INPUT_WINDOW_START_MSB, 0x00,

	R_9A_A_VERT_INPUT_WINDOW_LENGTH, 0x0c,
	R_9B_A_VERT_INPUT_WINDOW_LENGTH_MSB, 0x00,

	R_9C_A_HORIZ_OUTPUT_WINDOW_LENGTH, 0xa0,
	R_9D_A_HORIZ_OUTPUT_WINDOW_LENGTH_MSB, 0x05,

	R_9E_A_VERT_OUTPUT_WINDOW_LENGTH, 0x0c,
	R_9F_A_VERT_OUTPUT_WINDOW_LENGTH_MSB, 0x00,

	/* Task B */
	R_C0_B_TASK_HANDLING_CNTL, 0x00,
	R_C1_B_X_PORT_FORMATS_AND_CONF, 0x08,
	R_C2_B_INPUT_REFERENCE_SIGNAL_DEFINITION, 0x00,
	R_C3_B_I_PORT_FORMATS_AND_CONF, 0x80,

	/* 0x0002 is minimum */
	R_C4_B_HORIZ_INPUT_WINDOW_START, 0x02,
	R_C5_B_HORIZ_INPUT_WINDOW_START_MSB, 0x00,

	/* 0x02d0 = 720 */
	R_C6_B_HORIZ_INPUT_WINDOW_LENGTH, 0xd0,
	R_C7_B_HORIZ_INPUT_WINDOW_LENGTH_MSB, 0x02,

	/* vwindow start 0x12 = 18 */
	R_C8_B_VERT_INPUT_WINDOW_START, 0x12,
	R_C9_B_VERT_INPUT_WINDOW_START_MSB, 0x00,

	/* vwindow length 0xf8 = 248 */
	R_CA_B_VERT_INPUT_WINDOW_LENGTH, 0xf8,
	R_CB_B_VERT_INPUT_WINDOW_LENGTH_MSB, 0x00,

	/* hwindow 0x02d0 = 720 */
	R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH, 0xd0,
	R_CD_B_HORIZ_OUTPUT_WINDOW_LENGTH_MSB, 0x02,

	R_F0_LFCO_PER_LINE, 0xad,		/* Set PLL Register. 60hz 525 lines per frame, 27 MHz */
	R_F1_P_I_PARAM_SELECT, 0x05,		/* low bit with 0xF0 */
	R_F5_PULSGEN_LINE_LENGTH, 0xad,
	R_F6_PULSE_A_POS_LSB_AND_PULSEGEN_CONFIG, 0x01,

	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x00,	/* Disable I-port output */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler */
	R_80_GLOBAL_CNTL_1, 0x20,			/* Activate only task "B", continuous mode (was 0xA0) */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,		/* activate scaler */
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x01,	/* Enable I-port output */
	0x00, 0x00
};

static const unsigned char saa7115_cfg_50hz_video[] = {
	R_80_GLOBAL_CNTL_1, 0x00,
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,	/* reset scaler */

	R_15_VGATE_START_FID_CHG, 0x37,		/* VGATE start */
	R_16_VGATE_STOP, 0x16,
	R_17_MISC_VGATE_CONF_AND_MSB, 0x99,

	R_08_SYNC_CNTL, 0x28,			/* 0x28 = PAL */
	R_0E_CHROMA_CNTL_1, 0x07,

	R_5A_V_OFF_FOR_SLICER, 0x03,		/* standard 50hz value */

	/* Task A */
	R_90_A_TASK_HANDLING_CNTL, 0x81,
	R_91_A_X_PORT_FORMATS_AND_CONF, 0x48,
	R_92_A_X_PORT_INPUT_REFERENCE_SIGNAL, 0x40,
	R_93_A_I_PORT_OUTPUT_FORMATS_AND_CONF, 0x84,

	/* This is weird: the datasheet says that you should use 2 as the minimum value, */
	/* but Hauppauge uses 0, and changing that to 2 causes indeed problems (for 50hz) */
	/* hoffset low (input), 0x0002 is minimum */
	R_94_A_HORIZ_INPUT_WINDOW_START, 0x00,
	R_95_A_HORIZ_INPUT_WINDOW_START_MSB, 0x00,

	/* hsize low (input), 0x02d0 = 720 */
	R_96_A_HORIZ_INPUT_WINDOW_LENGTH, 0xd0,
	R_97_A_HORIZ_INPUT_WINDOW_LENGTH_MSB, 0x02,

	R_98_A_VERT_INPUT_WINDOW_START, 0x03,
	R_99_A_VERT_INPUT_WINDOW_START_MSB, 0x00,

	/* vsize 0x12 = 18 */
	R_9A_A_VERT_INPUT_WINDOW_LENGTH, 0x12,
	R_9B_A_VERT_INPUT_WINDOW_LENGTH_MSB, 0x00,

	/* hsize 0x05a0 = 1440 */
	R_9C_A_HORIZ_OUTPUT_WINDOW_LENGTH, 0xa0,
	R_9D_A_HORIZ_OUTPUT_WINDOW_LENGTH_MSB, 0x05,	/* hsize hi (output) */
	R_9E_A_VERT_OUTPUT_WINDOW_LENGTH, 0x12,		/* vsize low (output), 0x12 = 18 */
	R_9F_A_VERT_OUTPUT_WINDOW_LENGTH_MSB, 0x00,	/* vsize hi (output) */

	/* Task B */
	R_C0_B_TASK_HANDLING_CNTL, 0x00,
	R_C1_B_X_PORT_FORMATS_AND_CONF, 0x08,
	R_C2_B_INPUT_REFERENCE_SIGNAL_DEFINITION, 0x00,
	R_C3_B_I_PORT_FORMATS_AND_CONF, 0x80,

	/* This is weird: the datasheet says that you should use 2 as the minimum value, */
	/* but Hauppauge uses 0, and changing that to 2 causes indeed problems (for 50hz) */
	/* hoffset low (input), 0x0002 is minimum. See comment above. */
	R_C4_B_HORIZ_INPUT_WINDOW_START, 0x00,
	R_C5_B_HORIZ_INPUT_WINDOW_START_MSB, 0x00,

	/* hsize 0x02d0 = 720 */
	R_C6_B_HORIZ_INPUT_WINDOW_LENGTH, 0xd0,
	R_C7_B_HORIZ_INPUT_WINDOW_LENGTH_MSB, 0x02,

	/* voffset 0x16 = 22 */
	R_C8_B_VERT_INPUT_WINDOW_START, 0x16,
	R_C9_B_VERT_INPUT_WINDOW_START_MSB, 0x00,

	/* vsize 0x0120 = 288 */
	R_CA_B_VERT_INPUT_WINDOW_LENGTH, 0x20,
	R_CB_B_VERT_INPUT_WINDOW_LENGTH_MSB, 0x01,

	/* hsize 0x02d0 = 720 */
	R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH, 0xd0,
	R_CD_B_HORIZ_OUTPUT_WINDOW_LENGTH_MSB, 0x02,

	/* vsize 0x0120 = 288 */
	R_CE_B_VERT_OUTPUT_WINDOW_LENGTH, 0x20,
	R_CF_B_VERT_OUTPUT_WINDOW_LENGTH_MSB, 0x01,

	R_F0_LFCO_PER_LINE, 0xb0,		/* Set PLL Register. 50hz 625 lines per frame, 27 MHz */
	R_F1_P_I_PARAM_SELECT, 0x05,		/* low bit with 0xF0, (was 0x05) */
	R_F5_PULSGEN_LINE_LENGTH, 0xb0,
	R_F6_PULSE_A_POS_LSB_AND_PULSEGEN_CONFIG, 0x01,

	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x00,	/* Disable I-port output */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler (was 0xD0) */
	R_80_GLOBAL_CNTL_1, 0x20,			/* Activate only task "B" */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,		/* activate scaler */
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x01,	/* Enable I-port output */

	0x00, 0x00
};

/* ============== SAA7715 VIDEO templates (end) =======  */

static const unsigned char saa7115_cfg_vbi_on[] = {
	R_80_GLOBAL_CNTL_1, 0x00,			/* reset tasks */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler */
	R_80_GLOBAL_CNTL_1, 0x30,			/* Activate both tasks */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,		/* activate scaler */
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x01,	/* Enable I-port output */

	0x00, 0x00
};

static const unsigned char saa7115_cfg_vbi_off[] = {
	R_80_GLOBAL_CNTL_1, 0x00,			/* reset tasks */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,		/* reset scaler */
	R_80_GLOBAL_CNTL_1, 0x20,			/* Activate only task "B" */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,		/* activate scaler */
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x01,	/* Enable I-port output */

	0x00, 0x00
};


static const unsigned char saa7115_init_misc[] = {
	R_81_V_SYNC_FLD_ID_SRC_SEL_AND_RETIMED_V_F, 0x01,
	0x82, 0x00,		/* Reserved register - value should be zero*/
	R_83_X_PORT_I_O_ENA_AND_OUT_CLK, 0x01,
	R_84_I_PORT_SIGNAL_DEF, 0x20,
	R_85_I_PORT_SIGNAL_POLAR, 0x21,
	R_86_I_PORT_FIFO_FLAG_CNTL_AND_ARBIT, 0xc5,
	R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED, 0x01,

	/* Task A */
	R_A0_A_HORIZ_PRESCALING, 0x01,
	R_A1_A_ACCUMULATION_LENGTH, 0x00,
	R_A2_A_PRESCALER_DC_GAIN_AND_FIR_PREFILTER, 0x00,

	/* Configure controls at nominal value*/
	R_A4_A_LUMA_BRIGHTNESS_CNTL, 0x80,
	R_A5_A_LUMA_CONTRAST_CNTL, 0x40,
	R_A6_A_CHROMA_SATURATION_CNTL, 0x40,

	/* note: 2 x zoom ensures that VBI lines have same length as video lines. */
	R_A8_A_HORIZ_LUMA_SCALING_INC, 0x00,
	R_A9_A_HORIZ_LUMA_SCALING_INC_MSB, 0x02,

	R_AA_A_HORIZ_LUMA_PHASE_OFF, 0x00,

	/* must be horiz lum scaling / 2 */
	R_AC_A_HORIZ_CHROMA_SCALING_INC, 0x00,
	R_AD_A_HORIZ_CHROMA_SCALING_INC_MSB, 0x01,

	/* must be offset luma / 2 */
	R_AE_A_HORIZ_CHROMA_PHASE_OFF, 0x00,

	R_B0_A_VERT_LUMA_SCALING_INC, 0x00,
	R_B1_A_VERT_LUMA_SCALING_INC_MSB, 0x04,

	R_B2_A_VERT_CHROMA_SCALING_INC, 0x00,
	R_B3_A_VERT_CHROMA_SCALING_INC_MSB, 0x04,

	R_B4_A_VERT_SCALING_MODE_CNTL, 0x01,

	R_B8_A_VERT_CHROMA_PHASE_OFF_00, 0x00,
	R_B9_A_VERT_CHROMA_PHASE_OFF_01, 0x00,
	R_BA_A_VERT_CHROMA_PHASE_OFF_10, 0x00,
	R_BB_A_VERT_CHROMA_PHASE_OFF_11, 0x00,

	R_BC_A_VERT_LUMA_PHASE_OFF_00, 0x00,
	R_BD_A_VERT_LUMA_PHASE_OFF_01, 0x00,
	R_BE_A_VERT_LUMA_PHASE_OFF_10, 0x00,
	R_BF_A_VERT_LUMA_PHASE_OFF_11, 0x00,

	/* Task B */
	R_D0_B_HORIZ_PRESCALING, 0x01,
	R_D1_B_ACCUMULATION_LENGTH, 0x00,
	R_D2_B_PRESCALER_DC_GAIN_AND_FIR_PREFILTER, 0x00,

	/* Configure controls at nominal value*/
	R_D4_B_LUMA_BRIGHTNESS_CNTL, 0x80,
	R_D5_B_LUMA_CONTRAST_CNTL, 0x40,
	R_D6_B_CHROMA_SATURATION_CNTL, 0x40,

	/* hor lum scaling 0x0400 = 1 */
	R_D8_B_HORIZ_LUMA_SCALING_INC, 0x00,
	R_D9_B_HORIZ_LUMA_SCALING_INC_MSB, 0x04,

	R_DA_B_HORIZ_LUMA_PHASE_OFF, 0x00,

	/* must be hor lum scaling / 2 */
	R_DC_B_HORIZ_CHROMA_SCALING, 0x00,
	R_DD_B_HORIZ_CHROMA_SCALING_MSB, 0x02,

	/* must be offset luma / 2 */
	R_DE_B_HORIZ_PHASE_OFFSET_CRHOMA, 0x00,

	R_E0_B_VERT_LUMA_SCALING_INC, 0x00,
	R_E1_B_VERT_LUMA_SCALING_INC_MSB, 0x04,

	R_E2_B_VERT_CHROMA_SCALING_INC, 0x00,
	R_E3_B_VERT_CHROMA_SCALING_INC_MSB, 0x04,

	R_E4_B_VERT_SCALING_MODE_CNTL, 0x01,

	R_E8_B_VERT_CHROMA_PHASE_OFF_00, 0x00,
	R_E9_B_VERT_CHROMA_PHASE_OFF_01, 0x00,
	R_EA_B_VERT_CHROMA_PHASE_OFF_10, 0x00,
	R_EB_B_VERT_CHROMA_PHASE_OFF_11, 0x00,

	R_EC_B_VERT_LUMA_PHASE_OFF_00, 0x00,
	R_ED_B_VERT_LUMA_PHASE_OFF_01, 0x00,
	R_EE_B_VERT_LUMA_PHASE_OFF_10, 0x00,
	R_EF_B_VERT_LUMA_PHASE_OFF_11, 0x00,

	R_F2_NOMINAL_PLL2_DTO, 0x50,		/* crystal clock = 24.576 MHz, target = 27MHz */
	R_F3_PLL_INCREMENT, 0x46,
	R_F4_PLL2_STATUS, 0x00,
	R_F7_PULSE_A_POS_MSB, 0x4b,		/* not the recommended settings! */
	R_F8_PULSE_B_POS, 0x00,
	R_F9_PULSE_B_POS_MSB, 0x4b,
	R_FA_PULSE_C_POS, 0x00,
	R_FB_PULSE_C_POS_MSB, 0x4b,

	/* PLL2 lock detection settings: 71 lines 50% phase error */
	R_FF_S_PLL_MAX_PHASE_ERR_THRESH_NUM_LINES, 0x88,

	/* Turn off VBI */
	R_40_SLICER_CNTL_1, 0x20,             /* No framing code errors allowed. */
	R_41_LCR_BASE, 0xff,
	R_41_LCR_BASE+1, 0xff,
	R_41_LCR_BASE+2, 0xff,
	R_41_LCR_BASE+3, 0xff,
	R_41_LCR_BASE+4, 0xff,
	R_41_LCR_BASE+5, 0xff,
	R_41_LCR_BASE+6, 0xff,
	R_41_LCR_BASE+7, 0xff,
	R_41_LCR_BASE+8, 0xff,
	R_41_LCR_BASE+9, 0xff,
	R_41_LCR_BASE+10, 0xff,
	R_41_LCR_BASE+11, 0xff,
	R_41_LCR_BASE+12, 0xff,
	R_41_LCR_BASE+13, 0xff,
	R_41_LCR_BASE+14, 0xff,
	R_41_LCR_BASE+15, 0xff,
	R_41_LCR_BASE+16, 0xff,
	R_41_LCR_BASE+17, 0xff,
	R_41_LCR_BASE+18, 0xff,
	R_41_LCR_BASE+19, 0xff,
	R_41_LCR_BASE+20, 0xff,
	R_41_LCR_BASE+21, 0xff,
	R_41_LCR_BASE+22, 0xff,
	R_58_PROGRAM_FRAMING_CODE, 0x40,
	R_59_H_OFF_FOR_SLICER, 0x47,
	R_5B_FLD_OFF_AND_MSB_FOR_H_AND_V_OFF, 0x83,
	R_5D_DID, 0xbd,
	R_5E_SDID, 0x35,

	R_02_INPUT_CNTL_1, 0x84,		/* input tuner -> input 4, amplifier active */
	R_09_LUMA_CNTL, 0x53,			/* 0x53, was 0x56 for 60hz. luminance control */

	R_80_GLOBAL_CNTL_1, 0x20,		/* enable task B */
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xd0,
	R_88_POWER_SAVE_ADC_PORT_CNTL, 0xf0,
	0x00, 0x00
};

static int saa711x_odd_parity(u8 c)
{
	c ^= (c >> 4);
	c ^= (c >> 2);
	c ^= (c >> 1);

	return c & 1;
}

static int saa711x_decode_vps(u8 * dst, u8 * p)
{
	static const u8 biphase_tbl[] = {
		0xf0, 0x78, 0x70, 0xf0, 0xb4, 0x3c, 0x34, 0xb4,
		0xb0, 0x38, 0x30, 0xb0, 0xf0, 0x78, 0x70, 0xf0,
		0xd2, 0x5a, 0x52, 0xd2, 0x96, 0x1e, 0x16, 0x96,
		0x92, 0x1a, 0x12, 0x92, 0xd2, 0x5a, 0x52, 0xd2,
		0xd0, 0x58, 0x50, 0xd0, 0x94, 0x1c, 0x14, 0x94,
		0x90, 0x18, 0x10, 0x90, 0xd0, 0x58, 0x50, 0xd0,
		0xf0, 0x78, 0x70, 0xf0, 0xb4, 0x3c, 0x34, 0xb4,
		0xb0, 0x38, 0x30, 0xb0, 0xf0, 0x78, 0x70, 0xf0,
		0xe1, 0x69, 0x61, 0xe1, 0xa5, 0x2d, 0x25, 0xa5,
		0xa1, 0x29, 0x21, 0xa1, 0xe1, 0x69, 0x61, 0xe1,
		0xc3, 0x4b, 0x43, 0xc3, 0x87, 0x0f, 0x07, 0x87,
		0x83, 0x0b, 0x03, 0x83, 0xc3, 0x4b, 0x43, 0xc3,
		0xc1, 0x49, 0x41, 0xc1, 0x85, 0x0d, 0x05, 0x85,
		0x81, 0x09, 0x01, 0x81, 0xc1, 0x49, 0x41, 0xc1,
		0xe1, 0x69, 0x61, 0xe1, 0xa5, 0x2d, 0x25, 0xa5,
		0xa1, 0x29, 0x21, 0xa1, 0xe1, 0x69, 0x61, 0xe1,
		0xe0, 0x68, 0x60, 0xe0, 0xa4, 0x2c, 0x24, 0xa4,
		0xa0, 0x28, 0x20, 0xa0, 0xe0, 0x68, 0x60, 0xe0,
		0xc2, 0x4a, 0x42, 0xc2, 0x86, 0x0e, 0x06, 0x86,
		0x82, 0x0a, 0x02, 0x82, 0xc2, 0x4a, 0x42, 0xc2,
		0xc0, 0x48, 0x40, 0xc0, 0x84, 0x0c, 0x04, 0x84,
		0x80, 0x08, 0x00, 0x80, 0xc0, 0x48, 0x40, 0xc0,
		0xe0, 0x68, 0x60, 0xe0, 0xa4, 0x2c, 0x24, 0xa4,
		0xa0, 0x28, 0x20, 0xa0, 0xe0, 0x68, 0x60, 0xe0,
		0xf0, 0x78, 0x70, 0xf0, 0xb4, 0x3c, 0x34, 0xb4,
		0xb0, 0x38, 0x30, 0xb0, 0xf0, 0x78, 0x70, 0xf0,
		0xd2, 0x5a, 0x52, 0xd2, 0x96, 0x1e, 0x16, 0x96,
		0x92, 0x1a, 0x12, 0x92, 0xd2, 0x5a, 0x52, 0xd2,
		0xd0, 0x58, 0x50, 0xd0, 0x94, 0x1c, 0x14, 0x94,
		0x90, 0x18, 0x10, 0x90, 0xd0, 0x58, 0x50, 0xd0,
		0xf0, 0x78, 0x70, 0xf0, 0xb4, 0x3c, 0x34, 0xb4,
		0xb0, 0x38, 0x30, 0xb0, 0xf0, 0x78, 0x70, 0xf0,
	};
	int i;
	u8 c, err = 0;

	for (i = 0; i < 2 * 13; i += 2) {
		err |= biphase_tbl[p[i]] | biphase_tbl[p[i + 1]];
		c = (biphase_tbl[p[i + 1]] & 0xf) | ((biphase_tbl[p[i]] & 0xf) << 4);
		dst[i / 2] = c;
	}
	return err & 0xf0;
}

static int saa711x_decode_wss(u8 * p)
{
	static const int wss_bits[8] = {
		0, 0, 0, 1, 0, 1, 1, 1
	};
	unsigned char parity;
	int wss = 0;
	int i;

	for (i = 0; i < 16; i++) {
		int b1 = wss_bits[p[i] & 7];
		int b2 = wss_bits[(p[i] >> 3) & 7];

		if (b1 == b2)
			return -1;
		wss |= b2 << i;
	}
	parity = wss & 15;
	parity ^= parity >> 2;
	parity ^= parity >> 1;

	if (!(parity & 1))
		return -1;

	return wss;
}

static int saa711x_set_audio_clock_freq(struct i2c_client *client, u32 freq)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	u32 acpf;
	u32 acni;
	u32 hz;
	u64 f;
	u8 acc = 0; 	/* reg 0x3a, audio clock control */

	/* Checks for chips that don't have audio clock (saa7111, saa7113) */
	if (!saa711x_has_reg(state->ident,R_30_AUD_MAST_CLK_CYCLES_PER_FIELD))
		return 0;

	v4l_dbg(1, debug, client, "set audio clock freq: %d\n", freq);

	/* sanity check */
	if (freq < 32000 || freq > 48000)
		return -EINVAL;

	/* hz is the refresh rate times 100 */
	hz = (state->std & V4L2_STD_525_60) ? 5994 : 5000;
	/* acpf = (256 * freq) / field_frequency == (256 * 100 * freq) / hz */
	acpf = (25600 * freq) / hz;
	/* acni = (256 * freq * 2^23) / crystal_frequency =
		  (freq * 2^(8+23)) / crystal_frequency =
		  (freq << 31) / crystal_frequency */
	f = freq;
	f = f << 31;
	do_div(f, state->crystal_freq);
	acni = f;
	if (state->ucgc) {
		acpf = acpf * state->cgcdiv / 16;
		acni = acni * state->cgcdiv / 16;
		acc = 0x80;
		if (state->cgcdiv == 3)
			acc |= 0x40;
	}
	if (state->apll)
		acc |= 0x08;

	saa711x_write(client, R_38_CLK_RATIO_AMXCLK_TO_ASCLK, 0x03);
	saa711x_write(client, R_39_CLK_RATIO_ASCLK_TO_ALRCLK, 0x10);
	saa711x_write(client, R_3A_AUD_CLK_GEN_BASIC_SETUP, acc);

	saa711x_write(client, R_30_AUD_MAST_CLK_CYCLES_PER_FIELD, acpf & 0xff);
	saa711x_write(client, R_30_AUD_MAST_CLK_CYCLES_PER_FIELD+1,
							(acpf >> 8) & 0xff);
	saa711x_write(client, R_30_AUD_MAST_CLK_CYCLES_PER_FIELD+2,
							(acpf >> 16) & 0x03);

	saa711x_write(client, R_34_AUD_MAST_CLK_NOMINAL_INC, acni & 0xff);
	saa711x_write(client, R_34_AUD_MAST_CLK_NOMINAL_INC+1, (acni >> 8) & 0xff);
	saa711x_write(client, R_34_AUD_MAST_CLK_NOMINAL_INC+2, (acni >> 16) & 0x3f);
	state->audclk_freq = freq;
	return 0;
}

static int saa711x_set_v4lctrl(struct i2c_client *client, struct v4l2_control *ctrl)
{
	struct saa711x_state *state = i2c_get_clientdata(client);

	switch (ctrl->id) {
	case V4L2_CID_BRIGHTNESS:
		if (ctrl->value < 0 || ctrl->value > 255) {
			v4l_err(client, "invalid brightness setting %d\n", ctrl->value);
			return -ERANGE;
		}

		state->bright = ctrl->value;
		saa711x_write(client, R_0A_LUMA_BRIGHT_CNTL, state->bright);
		break;

	case V4L2_CID_CONTRAST:
		if (ctrl->value < 0 || ctrl->value > 127) {
			v4l_err(client, "invalid contrast setting %d\n", ctrl->value);
			return -ERANGE;
		}

		state->contrast = ctrl->value;
		saa711x_write(client, R_0B_LUMA_CONTRAST_CNTL, state->contrast);
		break;

	case V4L2_CID_SATURATION:
		if (ctrl->value < 0 || ctrl->value > 127) {
			v4l_err(client, "invalid saturation setting %d\n", ctrl->value);
			return -ERANGE;
		}

		state->sat = ctrl->value;
		saa711x_write(client, R_0C_CHROMA_SAT_CNTL, state->sat);
		break;

	case V4L2_CID_HUE:
		if (ctrl->value < -127 || ctrl->value > 127) {
			v4l_err(client, "invalid hue setting %d\n", ctrl->value);
			return -ERANGE;
		}

		state->hue = ctrl->value;
		saa711x_write(client, R_0D_CHROMA_HUE_CNTL, state->hue);
		break;

	default:
		return -EINVAL;
	}

	return 0;
}

static int saa711x_get_v4lctrl(struct i2c_client *client, struct v4l2_control *ctrl)
{
	struct saa711x_state *state = i2c_get_clientdata(client);

	switch (ctrl->id) {
	case V4L2_CID_BRIGHTNESS:
		ctrl->value = state->bright;
		break;
	case V4L2_CID_CONTRAST:
		ctrl->value = state->contrast;
		break;
	case V4L2_CID_SATURATION:
		ctrl->value = state->sat;
		break;
	case V4L2_CID_HUE:
		ctrl->value = state->hue;
		break;
	default:
		return -EINVAL;
	}

	return 0;
}

static void saa711x_set_v4lstd(struct i2c_client *client, v4l2_std_id std)
{
	struct saa711x_state *state = i2c_get_clientdata(client);

	/* Prevent unnecessary standard changes. During a standard
	   change the I-Port is temporarily disabled. Any devices
	   reading from that port can get confused.
	   Note that VIDIOC_S_STD is also used to switch from
	   radio to TV mode, so if a VIDIOC_S_STD is broadcast to
	   all I2C devices then you do not want to have an unwanted
	   side-effect here. */
	if (std == state->std)
		return;

	// This works for NTSC-M, SECAM-L and the 50Hz PAL variants.
	if (std & V4L2_STD_525_60) {
		v4l_dbg(1, debug, client, "decoder set standard 60 Hz\n");
		saa711x_writeregs(client, saa7115_cfg_60hz_video);
	} else {
		v4l_dbg(1, debug, client, "decoder set standard 50 Hz\n");
		saa711x_writeregs(client, saa7115_cfg_50hz_video);
	}

	/* Register 0E - Bits D6-D4 on NO-AUTO mode
		(SAA7111 and SAA7113 doesn't have auto mode)
	    50 Hz / 625 lines           60 Hz / 525 lines
	000 PAL BGDHI (4.43Mhz)         NTSC M (3.58MHz)
	001 NTSC 4.43 (50 Hz)           PAL 4.43 (60 Hz)
	010 Combination-PAL N (3.58MHz) NTSC 4.43 (60 Hz)
	011 NTSC N (3.58MHz)            PAL M (3.58MHz)
	100 reserved                    NTSC-Japan (3.58MHz)
	*/
	state->std = std;

	if (state->ident == V4L2_IDENT_SAA7111 ||
	    state->ident == V4L2_IDENT_SAA7113) {
		u8 reg = saa711x_read(client, R_0E_CHROMA_CNTL_1) & 0x8f;

		if (std == V4L2_STD_PAL_M) {
			reg |= 0x30;
		} else if (std == V4L2_STD_PAL_N) {
			reg |= 0x20;
		} else if (std == V4L2_STD_PAL_60) {
			reg |= 0x10;
		} else if (std == V4L2_STD_NTSC_M_JP) {
			reg |= 0x40;
		}
		saa711x_write(client, R_0E_CHROMA_CNTL_1, reg);
	} else {
		/* restart task B if needed */
		int taskb = saa711x_read(client, R_80_GLOBAL_CNTL_1) & 0x10;

		if (taskb && state->ident == V4L2_IDENT_SAA7114) {
			saa711x_writeregs(client, saa7115_cfg_vbi_on);
		}

		/* switch audio mode too! */
		saa711x_set_audio_clock_freq(client, state->audclk_freq);
	}
}

static v4l2_std_id saa711x_get_v4lstd(struct i2c_client *client)
{
	struct saa711x_state *state = i2c_get_clientdata(client);

	return state->std;
}

static void saa711x_log_status(struct i2c_client *client)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	int reg1e, reg1f;
	int signalOk;
	int vcr;

	v4l_info(client, "Audio frequency: %d Hz\n", state->audclk_freq);
	if (state->ident != V4L2_IDENT_SAA7115) {
		/* status for the saa7114 */
		reg1f = saa711x_read(client, R_1F_STATUS_BYTE_2_VD_DEC);
		signalOk = (reg1f & 0xc1) == 0x81;
		v4l_info(client, "Video signal:    %s\n", signalOk ? "ok" : "bad");
		v4l_info(client, "Frequency:       %s\n", (reg1f & 0x20) ? "60 Hz" : "50 Hz");
		return;
	}

	/* status for the saa7115 */
	reg1e = saa711x_read(client, R_1E_STATUS_BYTE_1_VD_DEC);
	reg1f = saa711x_read(client, R_1F_STATUS_BYTE_2_VD_DEC);

	signalOk = (reg1f & 0xc1) == 0x81 && (reg1e & 0xc0) == 0x80;
	vcr = !(reg1f & 0x10);

	if (state->input >= 6) {
		v4l_info(client, "Input:           S-Video %d\n", state->input - 6);
	} else {
		v4l_info(client, "Input:           Composite %d\n", state->input);
	}
	v4l_info(client, "Video signal:    %s\n", signalOk ? (vcr ? "VCR" : "broadcast/DVD") : "bad");
	v4l_info(client, "Frequency:       %s\n", (reg1f & 0x20) ? "60 Hz" : "50 Hz");

	switch (reg1e & 0x03) {
		case 1:
			v4l_info(client, "Detected format: NTSC\n");
			break;
		case 2:
			v4l_info(client, "Detected format: PAL\n");
			break;
		case 3:
			v4l_info(client, "Detected format: SECAM\n");
			break;
		default:
			v4l_info(client, "Detected format: BW/No color\n");
			break;
	}
}

/* setup the sliced VBI lcr registers according to the sliced VBI format */
static void saa711x_set_lcr(struct i2c_client *client, struct v4l2_sliced_vbi_format *fmt)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	int is_50hz = (state->std & V4L2_STD_625_50);
	u8 lcr[24];
	int i, x;

#if 1
	/* saa7113/7114/7118 VBI support are experimental */
	if (!saa711x_has_reg(state->ident,R_41_LCR_BASE))
		return;

#else
	/* SAA7113 and SAA7118 also should support VBI - Need testing */
	if (state->ident != V4L2_IDENT_SAA7115)
		return;
#endif

	for (i = 0; i <= 23; i++)
		lcr[i] = 0xff;

	if (fmt->service_set == 0) {
		/* raw VBI */
		if (is_50hz)
			for (i = 6; i <= 23; i++)
				lcr[i] = 0xdd;
		else
			for (i = 10; i <= 21; i++)
				lcr[i] = 0xdd;
	} else {
		/* sliced VBI */
		/* first clear lines that cannot be captured */
		if (is_50hz) {
			for (i = 0; i <= 5; i++)
				fmt->service_lines[0][i] =
					fmt->service_lines[1][i] = 0;
		}
		else {
			for (i = 0; i <= 9; i++)
				fmt->service_lines[0][i] =
					fmt->service_lines[1][i] = 0;
			for (i = 22; i <= 23; i++)
				fmt->service_lines[0][i] =
					fmt->service_lines[1][i] = 0;
		}

		/* Now set the lcr values according to the specified service */
		for (i = 6; i <= 23; i++) {
			lcr[i] = 0;
			for (x = 0; x <= 1; x++) {
				switch (fmt->service_lines[1-x][i]) {
					case 0:
						lcr[i] |= 0xf << (4 * x);
						break;
					case V4L2_SLICED_TELETEXT_B:
						lcr[i] |= 1 << (4 * x);
						break;
					case V4L2_SLICED_CAPTION_525:
						lcr[i] |= 4 << (4 * x);
						break;
					case V4L2_SLICED_WSS_625:
						lcr[i] |= 5 << (4 * x);
						break;
					case V4L2_SLICED_VPS:
						lcr[i] |= 7 << (4 * x);
						break;
				}
			}
		}
	}

	/* write the lcr registers */
	for (i = 2; i <= 23; i++) {
		saa711x_write(client, i - 2 + R_41_LCR_BASE, lcr[i]);
	}

	/* enable/disable raw VBI capturing */
	saa711x_writeregs(client, fmt->service_set == 0 ?
				saa7115_cfg_vbi_on :
				saa7115_cfg_vbi_off);
}

static int saa711x_get_v4lfmt(struct i2c_client *client, struct v4l2_format *fmt)
{
	static u16 lcr2vbi[] = {
		0, V4L2_SLICED_TELETEXT_B, 0,	/* 1 */
		0, V4L2_SLICED_CAPTION_525,	/* 4 */
		V4L2_SLICED_WSS_625, 0,		/* 5 */
		V4L2_SLICED_VPS, 0, 0, 0, 0,	/* 7 */
		0, 0, 0, 0
	};
	struct v4l2_sliced_vbi_format *sliced = &fmt->fmt.sliced;
	int i;

	if (fmt->type != V4L2_BUF_TYPE_SLICED_VBI_CAPTURE)
		return -EINVAL;
	memset(sliced, 0, sizeof(*sliced));
	/* done if using raw VBI */
	if (saa711x_read(client, R_80_GLOBAL_CNTL_1) & 0x10)
		return 0;
	for (i = 2; i <= 23; i++) {
		u8 v = saa711x_read(client, i - 2 + R_41_LCR_BASE);

		sliced->service_lines[0][i] = lcr2vbi[v >> 4];
		sliced->service_lines[1][i] = lcr2vbi[v & 0xf];
		sliced->service_set |=
			sliced->service_lines[0][i] | sliced->service_lines[1][i];
	}
	return 0;
}

static int saa711x_set_size(struct i2c_client *client, int width, int height)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	int HPSC, HFSC;
	int VSCY;
	int res;
	int is_50hz = state->std & V4L2_STD_625_50;
	int Vsrc = is_50hz ? 576 : 480+16;

	v4l_dbg(1, debug, client, "decoder set size to %ix%i\n",width,height);

	/* FIXME need better bounds checking here */
	if ((width < 1) || (width > 1440))
		return -EINVAL;
	if ((height < 1) || (height > 960))
		return -EINVAL;

	if (!saa711x_has_reg(state->ident,R_D0_B_HORIZ_PRESCALING)) {
		/* Decoder only supports 720 columns and 480 or 576 lines */
		if (width != 720)
			return -EINVAL;
		if (height != Vsrc)
			return -EINVAL;
	}
	if (!saa711x_has_reg(state->ident,R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH))
		return 0;

	/* probably have a valid size, let's set it */
	/* Set output width/height */
	/* width */

	saa711x_write(client, R_CC_B_HORIZ_OUTPUT_WINDOW_LENGTH,
					(u8) (width & 0xff));
	saa711x_write(client, R_CD_B_HORIZ_OUTPUT_WINDOW_LENGTH_MSB,
					(u8) ((width >> 8) & 0xff));

	/* Vertical Scaling uses height/2 */
	res=height/2;

		/* height */
	saa711x_write(client, R_CE_B_VERT_OUTPUT_WINDOW_LENGTH,
					(u8) (res & 0xff));
	saa711x_write(client, R_CF_B_VERT_OUTPUT_WINDOW_LENGTH_MSB,
					(u8) ((res >> 8) & 0xff));

	/* Scaling settings */
	/* Hprescaler is floor(inres/outres) */
	HPSC = (int)(720 / width);
	/* 0 is not allowed (div. by zero) */
	HPSC = HPSC ? HPSC : 1;
	HFSC = (int)((1024 * 720) / (HPSC * width));
	/* FIXME hardcodes to "Task B"
	 * write H prescaler integer */
	saa711x_write(client, R_D0_B_HORIZ_PRESCALING,
				(u8) (HPSC & 0x3f));

	v4l_dbg(1, debug, client, "Hpsc: 0x%05x, Hfsc: 0x%05x\n", HPSC, HFSC);
	/* write H fine-scaling (luminance) */
	saa711x_write(client, R_D8_B_HORIZ_LUMA_SCALING_INC,
				(u8) (HFSC & 0xff));
	saa711x_write(client, R_D9_B_HORIZ_LUMA_SCALING_INC_MSB,
				(u8) ((HFSC >> 8) & 0xff));
	/* write H fine-scaling (chrominance)
	 * must be lum/2, so i'll just bitshift :) */
	saa711x_write(client, R_DC_B_HORIZ_CHROMA_SCALING,
				(u8) ((HFSC >> 1) & 0xff));
	saa711x_write(client, R_DD_B_HORIZ_CHROMA_SCALING_MSB,
				(u8) ((HFSC >> 9) & 0xff));

	VSCY = (int)((1024 * Vsrc) / height);
	v4l_dbg(1, debug, client, "Vsrc: %d, Vscy: 0x%05x\n", Vsrc, VSCY);

	/* Correct Contrast and Luminance */
	saa711x_write(client, R_D5_B_LUMA_CONTRAST_CNTL,
					(u8) (64 * 1024 / VSCY));
	saa711x_write(client, R_D6_B_CHROMA_SATURATION_CNTL,
					(u8) (64 * 1024 / VSCY));

		/* write V fine-scaling (luminance) */
	saa711x_write(client, R_E0_B_VERT_LUMA_SCALING_INC,
					(u8) (VSCY & 0xff));
	saa711x_write(client, R_E1_B_VERT_LUMA_SCALING_INC_MSB,
					(u8) ((VSCY >> 8) & 0xff));
		/* write V fine-scaling (chrominance) */
	saa711x_write(client, R_E2_B_VERT_CHROMA_SCALING_INC,
					(u8) (VSCY & 0xff));
	saa711x_write(client, R_E3_B_VERT_CHROMA_SCALING_INC_MSB,
					(u8) ((VSCY >> 8) & 0xff));

	saa711x_writeregs(client, saa7115_cfg_reset_scaler);

	return 0;
}

static int saa711x_set_v4lfmt(struct i2c_client *client, struct v4l2_format *fmt)
{
	if (fmt->type == V4L2_BUF_TYPE_SLICED_VBI_CAPTURE) {
		saa711x_set_lcr(client, &fmt->fmt.sliced);
		return 0;
	}
	if (fmt->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
		return -EINVAL;

	return saa711x_set_size(client,fmt->fmt.pix.width,fmt->fmt.pix.height);
}

/* Decode the sliced VBI data stream as created by the saa7115.
   The format is described in the saa7115 datasheet in Tables 25 and 26
   and in Figure 33.
   The current implementation uses SAV/EAV codes and not the ancillary data
   headers. The vbi->p pointer points to the R_5E_SDID byte right after the SAV
   code. */
static void saa711x_decode_vbi_line(struct i2c_client *client,
				    struct v4l2_decode_vbi_line *vbi)
{
	static const char vbi_no_data_pattern[] = {
		0xa0, 0xa0, 0xa0, 0xa0, 0xa0, 0xa0, 0xa0, 0xa0, 0xa0, 0xa0
	};
	struct saa711x_state *state = i2c_get_clientdata(client);
	u8 *p = vbi->p;
	u32 wss;
	int id1, id2;   /* the ID1 and ID2 bytes from the internal header */

	vbi->type = 0;  /* mark result as a failure */
	id1 = p[2];
	id2 = p[3];
	/* Note: the field bit is inverted for 60 Hz video */
	if (state->std & V4L2_STD_525_60)
		id1 ^= 0x40;

	/* Skip internal header, p now points to the start of the payload */
	p += 4;
	vbi->p = p;

	/* calculate field and line number of the VBI packet (1-23) */
	vbi->is_second_field = ((id1 & 0x40) != 0);
	vbi->line = (id1 & 0x3f) << 3;
	vbi->line |= (id2 & 0x70) >> 4;

	/* Obtain data type */
	id2 &= 0xf;

	/* If the VBI slicer does not detect any signal it will fill up
	   the payload buffer with 0xa0 bytes. */
	if (!memcmp(p, vbi_no_data_pattern, sizeof(vbi_no_data_pattern)))
		return;

	/* decode payloads */
	switch (id2) {
	case 1:
		vbi->type = V4L2_SLICED_TELETEXT_B;
		break;
	case 4:
		if (!saa711x_odd_parity(p[0]) || !saa711x_odd_parity(p[1]))
			return;
		vbi->type = V4L2_SLICED_CAPTION_525;
		break;
	case 5:
		wss = saa711x_decode_wss(p);
		if (wss == -1)
			return;
		p[0] = wss & 0xff;
		p[1] = wss >> 8;
		vbi->type = V4L2_SLICED_WSS_625;
		break;
	case 7:
		if (saa711x_decode_vps(p, p) != 0)
			return;
		vbi->type = V4L2_SLICED_VPS;
		break;
	default:
		return;
	}
}

/* ============ SAA7115 AUDIO settings (end) ============= */

static int saa711x_command(struct i2c_client *client, unsigned int cmd, void *arg)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	int *iarg = arg;

	/* ioctls to allow direct access to the saa7115 registers for testing */
	switch (cmd) {
	case VIDIOC_S_FMT:
		return saa711x_set_v4lfmt(client, (struct v4l2_format *)arg);

	case VIDIOC_G_FMT:
		return saa711x_get_v4lfmt(client, (struct v4l2_format *)arg);

	case VIDIOC_INT_AUDIO_CLOCK_FREQ:
		return saa711x_set_audio_clock_freq(client, *(u32 *)arg);

	case VIDIOC_G_TUNER:
	{
		struct v4l2_tuner *vt = arg;
		int status;

		if (state->radio)
			break;
		status = saa711x_read(client, R_1F_STATUS_BYTE_2_VD_DEC);

		v4l_dbg(1, debug, client, "status: 0x%02x\n", status);
		vt->signal = ((status & (1 << 6)) == 0) ? 0xffff : 0x0;
		break;
	}

	case VIDIOC_LOG_STATUS:
		saa711x_log_status(client);
		break;

	case VIDIOC_G_CTRL:
		return saa711x_get_v4lctrl(client, (struct v4l2_control *)arg);

	case VIDIOC_S_CTRL:
		return saa711x_set_v4lctrl(client, (struct v4l2_control *)arg);

	case VIDIOC_QUERYCTRL:
	{
		struct v4l2_queryctrl *qc = arg;

		switch (qc->id) {
			case V4L2_CID_BRIGHTNESS:
			case V4L2_CID_CONTRAST:
			case V4L2_CID_SATURATION:
			case V4L2_CID_HUE:
				return v4l2_ctrl_query_fill_std(qc);
			default:
				return -EINVAL;
		}
	}

	case VIDIOC_G_STD:
		*(v4l2_std_id *)arg = saa711x_get_v4lstd(client);
		break;

	case VIDIOC_S_STD:
		state->radio = 0;
		saa711x_set_v4lstd(client, *(v4l2_std_id *)arg);
		break;

	case AUDC_SET_RADIO:
		state->radio = 1;
		break;

	case VIDIOC_INT_G_VIDEO_ROUTING:
	{
		struct v4l2_routing *route = arg;

		route->input = state->input;
		route->output = 0;
		break;
	}

	case VIDIOC_INT_S_VIDEO_ROUTING:
	{
		struct v4l2_routing *route = arg;

		v4l_dbg(1, debug, client, "decoder set input %d\n", route->input);
		/* saa7113 does not have these inputs */
		if (state->ident == V4L2_IDENT_SAA7113 &&
		    (route->input == SAA7115_COMPOSITE4 ||
		     route->input == SAA7115_COMPOSITE5)) {
			return -EINVAL;
		}
		if (route->input > SAA7115_SVIDEO3)
			return -EINVAL;
		if (state->input == route->input)
			break;
		v4l_dbg(1, debug, client, "now setting %s input\n",
			(route->input >= SAA7115_SVIDEO0) ? "S-Video" : "Composite");
		state->input = route->input;

		/* select mode */
		saa711x_write(client, R_02_INPUT_CNTL_1,
			      (saa711x_read(client, R_02_INPUT_CNTL_1) & 0xf0) |
			       state->input);

		/* bypass chrominance trap for S-Video modes */
		saa711x_write(client, R_09_LUMA_CNTL,
			      (saa711x_read(client, R_09_LUMA_CNTL) & 0x7f) |
			       (state->input >= SAA7115_SVIDEO0 ? 0x80 : 0x0));
		break;
	}

	case VIDIOC_STREAMON:
	case VIDIOC_STREAMOFF:
		v4l_dbg(1, debug, client, "%s output\n",
			(cmd == VIDIOC_STREAMON) ? "enable" : "disable");

		if (state->enable != (cmd == VIDIOC_STREAMON)) {
			state->enable = (cmd == VIDIOC_STREAMON);
			saa711x_write(client,
				R_87_I_PORT_I_O_ENA_OUT_CLK_AND_GATED,
				state->enable);
		}
		break;

	case VIDIOC_INT_S_CRYSTAL_FREQ:
	{
		struct v4l2_crystal_freq *freq = arg;

		if (freq->freq != SAA7115_FREQ_32_11_MHZ &&
		    freq->freq != SAA7115_FREQ_24_576_MHZ)
			return -EINVAL;
		state->crystal_freq = freq->freq;
		state->cgcdiv = (freq->flags & SAA7115_FREQ_FL_CGCDIV) ? 3 : 4;
		state->ucgc = (freq->flags & SAA7115_FREQ_FL_UCGC) ? 1 : 0;
		state->apll = (freq->flags & SAA7115_FREQ_FL_APLL) ? 1 : 0;
		saa711x_set_audio_clock_freq(client, state->audclk_freq);
		break;
	}

	case VIDIOC_INT_DECODE_VBI_LINE:
		saa711x_decode_vbi_line(client, arg);
		break;

	case VIDIOC_INT_RESET:
		v4l_dbg(1, debug, client, "decoder RESET\n");
		saa711x_writeregs(client, saa7115_cfg_reset_scaler);
		break;

	case VIDIOC_INT_G_VBI_DATA:
	{
		struct v4l2_sliced_vbi_data *data = arg;

		switch (data->id) {
		case V4L2_SLICED_WSS_625:
			if (saa711x_read(client, 0x6b) & 0xc0)
				return -EIO;
			data->data[0] = saa711x_read(client, 0x6c);
			data->data[1] = saa711x_read(client, 0x6d);
			return 0;
		case V4L2_SLICED_CAPTION_525:
			if (data->field == 0) {
				/* CC */
				if (saa711x_read(client, 0x66) & 0xc0)
					return -EIO;
				data->data[0] = saa711x_read(client, 0x67);
				data->data[1] = saa711x_read(client, 0x68);
				return 0;
			}
			/* XDS */
			if (saa711x_read(client, 0x66) & 0x30)
				return -EIO;
			data->data[0] = saa711x_read(client, 0x69);
			data->data[1] = saa711x_read(client, 0x6a);
			return 0;
		default:
			return -EINVAL;
		}
		break;
	}

#ifdef CONFIG_VIDEO_ADV_DEBUG
	case VIDIOC_INT_G_REGISTER:
	{
		struct v4l2_register *reg = arg;

		if (reg->i2c_id != I2C_DRIVERID_SAA711X)
			return -EINVAL;
		reg->val = saa711x_read(client, reg->reg & 0xff);
		break;
	}

	case VIDIOC_INT_S_REGISTER:
	{
		struct v4l2_register *reg = arg;

		if (reg->i2c_id != I2C_DRIVERID_SAA711X)
			return -EINVAL;
		if (!capable(CAP_SYS_ADMIN))
			return -EPERM;
		saa711x_write(client, reg->reg & 0xff, reg->val & 0xff);
		break;
	}
#endif

	case VIDIOC_INT_G_CHIP_IDENT:
		*iarg = state->ident;
		break;

	default:
		return -EINVAL;
	}

	return 0;
}

/* ----------------------------------------------------------------------- */

static struct i2c_driver i2c_driver_saa711x;

static int saa711x_attach(struct i2c_adapter *adapter, int address, int kind)
{
	struct i2c_client *client;
	struct saa711x_state *state;
	int	i;
	char	name[17];
	u8 chip_id;

	/* Check if the adapter supports the needed features */
	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
		return 0;

	client = kzalloc(sizeof(struct i2c_client), GFP_KERNEL);
	if (client == 0)
		return -ENOMEM;
	client->addr = address;
	client->adapter = adapter;
	client->driver = &i2c_driver_saa711x;
	snprintf(client->name, sizeof(client->name) - 1, "saa7115");

	v4l_dbg(1, debug, client, "detecting saa7115 client on address 0x%x\n", address << 1);

	for (i=0;i<0x0f;i++) {
		saa711x_write(client, 0, i);
		name[i] = (saa711x_read(client, 0) &0x0f) +'0';
		if (name[i]>'9')
			name[i]+='a'-'9'-1;
	}
	name[i]='\0';

	saa711x_write(client, 0, 5);
	chip_id = saa711x_read(client, 0) & 0x0f;
	if (chip_id < 3 && chip_id > 5) {
		v4l_dbg(1, debug, client, "saa7115 not found\n");
		kfree(client);
		return 0;
	}
	snprintf(client->name, sizeof(client->name) - 1, "saa711%d",chip_id);
	v4l_info(client, "saa711%d found (%s) @ 0x%x (%s)\n", chip_id, name, address << 1, adapter->name);

	state = kzalloc(sizeof(struct saa711x_state), GFP_KERNEL);
	i2c_set_clientdata(client, state);
	if (state == NULL) {
		kfree(client);
		return -ENOMEM;
	}
	state->input = -1;
	state->enable = 1;
	state->radio = 0;
	state->bright = 128;
	state->contrast = 64;
	state->hue = 0;
	state->sat = 64;
	switch (chip_id) {
	case 1:
		state->ident = V4L2_IDENT_SAA7111;
		break;
	case 3:
		state->ident = V4L2_IDENT_SAA7113;
		break;
	case 4:
		state->ident = V4L2_IDENT_SAA7114;
		break;
	case 5:
		state->ident = V4L2_IDENT_SAA7115;
		break;
	case 8:
		state->ident = V4L2_IDENT_SAA7118;
		break;
	default:
		state->ident = V4L2_IDENT_SAA7111;
		v4l_info(client, "WARNING: Chip is not known - Falling back to saa7111\n");

	}

	state->audclk_freq = 48000;

	v4l_dbg(1, debug, client, "writing init values\n");

	/* init to 60hz/48khz */
	if (state->ident == V4L2_IDENT_SAA7111 ||
			state->ident == V4L2_IDENT_SAA7113) {
		state->crystal_freq = SAA7115_FREQ_24_576_MHZ;
		saa711x_writeregs(client, saa7113_init_auto_input);
	} else {
		state->crystal_freq = SAA7115_FREQ_32_11_MHZ;
		saa711x_writeregs(client, saa7115_init_auto_input);
	}
	saa711x_writeregs(client, saa7115_init_misc);
	state->std = V4L2_STD_NTSC;
	saa711x_set_size(client, 720, 480);
	saa711x_writeregs(client, saa7115_cfg_60hz_video);
	saa711x_set_audio_clock_freq(client, state->audclk_freq);
	saa711x_writeregs(client, saa7115_cfg_reset_scaler);

	i2c_attach_client(client);

	v4l_dbg(1, debug, client, "status: (1E) 0x%02x, (1F) 0x%02x\n",
		saa711x_read(client, R_1E_STATUS_BYTE_1_VD_DEC), saa711x_read(client, R_1F_STATUS_BYTE_2_VD_DEC));

	return 0;
}

static int saa711x_probe(struct i2c_adapter *adapter)
{
	if (adapter->class & I2C_CLASS_TV_ANALOG)
		return i2c_probe(adapter, &addr_data, &saa711x_attach);
	return 0;
}

static int saa711x_detach(struct i2c_client *client)
{
	struct saa711x_state *state = i2c_get_clientdata(client);
	int err;

	err = i2c_detach_client(client);
	if (err) {
		return err;
	}

	kfree(state);
	kfree(client);
	return 0;
}

/* ----------------------------------------------------------------------- */

/* i2c implementation */
static struct i2c_driver i2c_driver_saa711x = {
	.driver = {
		.name = "saa7115",
	},
	.id = I2C_DRIVERID_SAA711X,
	.attach_adapter = saa711x_probe,
	.detach_client = saa711x_detach,
	.command = saa711x_command,
};


static int __init saa711x_init_module(void)
{
	return i2c_add_driver(&i2c_driver_saa711x);
}

static void __exit saa711x_cleanup_module(void)
{
	i2c_del_driver(&i2c_driver_saa711x);
}

module_init(saa711x_init_module);
module_exit(saa711x_cleanup_module);