dm355evm_keys.c 8.5 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98
/*
 * dm355evm_keys.c - support buttons and IR remote on DM355 EVM board
 *
 * Copyright (c) 2008 by David Brownell
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version
 * 2 of the License, or (at your option) any later version.
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/input.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>

#include <linux/i2c/dm355evm_msp.h>


/*
 * The MSP430 firmware on the DM355 EVM monitors on-board pushbuttons
 * and an IR receptor used for the remote control.  When any key is
 * pressed, or its autorepeat kicks in, an event is sent.  This driver
 * read those events from the small (32 event) queue and reports them.
 *
 * Note that physically there can only be one of these devices.
 *
 * This driver was tested with firmware revision A4.
 */
struct dm355evm_keys {
	struct input_dev	*input;
	struct device		*dev;
	int			irq;
};

/* These initial keycodes can be remapped by dm355evm_setkeycode(). */
static struct {
	u16	event;
	u16	keycode;
} dm355evm_keys[] = {

	/*
	 * Pushbuttons on the EVM board ... note that the labels for these
	 * are SW10/SW11/etc on the PC board.  The left/right orientation
	 * comes only from the firmware's documentation, and presumes the
	 * power connector is immediately in front of you and the IR sensor
	 * is to the right.  (That is, rotate the board counter-clockwise
	 * by 90 degrees from the SW10/etc and "DM355 EVM" labels.)
	 */
	{ 0x00d8, KEY_OK, },		/* SW12 */
	{ 0x00b8, KEY_UP, },		/* SW13 */
	{ 0x00e8, KEY_DOWN, },		/* SW11 */
	{ 0x0078, KEY_LEFT, },		/* SW14 */
	{ 0x00f0, KEY_RIGHT, },		/* SW10 */

	/*
	 * IR buttons ... codes assigned to match the universal remote
	 * provided with the EVM (Philips PM4S) using DVD code 0020.
	 *
	 * These event codes match firmware documentation, but other
	 * remote controls could easily send more RC5-encoded events.
	 * The PM4S manual was used in several cases to help select
	 * a keycode reflecting the intended usage.
	 *
	 * RC5 codes are 14 bits, with two start bits (0x3 prefix)
	 * and a toggle bit (masked out below).
	 */
	{ 0x300c, KEY_POWER, },		/* NOTE: docs omit this */
	{ 0x3000, KEY_NUMERIC_0, },
	{ 0x3001, KEY_NUMERIC_1, },
	{ 0x3002, KEY_NUMERIC_2, },
	{ 0x3003, KEY_NUMERIC_3, },
	{ 0x3004, KEY_NUMERIC_4, },
	{ 0x3005, KEY_NUMERIC_5, },
	{ 0x3006, KEY_NUMERIC_6, },
	{ 0x3007, KEY_NUMERIC_7, },
	{ 0x3008, KEY_NUMERIC_8, },
	{ 0x3009, KEY_NUMERIC_9, },
	{ 0x3022, KEY_ENTER, },
	{ 0x30ec, KEY_MODE, },		/* "tv/vcr/..." */
	{ 0x300f, KEY_SELECT, },	/* "info" */
	{ 0x3020, KEY_CHANNELUP, },	/* "up" */
	{ 0x302e, KEY_MENU, },		/* "in/out" */
	{ 0x3011, KEY_VOLUMEDOWN, },	/* "left" */
	{ 0x300d, KEY_MUTE, },		/* "ok" */
	{ 0x3010, KEY_VOLUMEUP, },	/* "right" */
	{ 0x301e, KEY_SUBTITLE, },	/* "cc" */
	{ 0x3021, KEY_CHANNELDOWN, },	/* "down" */
	{ 0x3022, KEY_PREVIOUS, },
	{ 0x3026, KEY_SLEEP, },
	{ 0x3172, KEY_REWIND, },	/* NOTE: docs wrongly say 0x30ca */
	{ 0x3175, KEY_PLAY, },
	{ 0x3174, KEY_FASTFORWARD, },
	{ 0x3177, KEY_RECORD, },
	{ 0x3176, KEY_STOP, },
	{ 0x3169, KEY_PAUSE, },
};

99 100 101 102 103 104 105
/*
 * Because we communicate with the MSP430 using I2C, and all I2C calls
 * in Linux sleep, we use a threaded IRQ handler.  The IRQ itself is
 * active low, but we go through the GPIO controller so we can trigger
 * on falling edges and not worry about enabling/disabling the IRQ in
 * the keypress handling path.
 */
106
static irqreturn_t dm355evm_keys_irq(int irq, void *_keys)
107
{
108
	struct dm355evm_keys	*keys = _keys;
109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176
	int			status;

	/* For simplicity we ignore INPUT_COUNT and just read
	 * events until we get the "queue empty" indicator.
	 * Reading INPUT_LOW decrements the count.
	 */
	for (;;) {
		static u16	last_event;
		u16		event;
		int		keycode;
		int		i;

		status = dm355evm_msp_read(DM355EVM_MSP_INPUT_HIGH);
		if (status < 0) {
			dev_dbg(keys->dev, "input high err %d\n",
					status);
			break;
		}
		event = status << 8;

		status = dm355evm_msp_read(DM355EVM_MSP_INPUT_LOW);
		if (status < 0) {
			dev_dbg(keys->dev, "input low err %d\n",
					status);
			break;
		}
		event |= status;
		if (event == 0xdead)
			break;

		/* Press and release a button:  two events, same code.
		 * Press and hold (autorepeat), then release: N events
		 * (N > 2), same code.  For RC5 buttons the toggle bits
		 * distinguish (for example) "1-autorepeat" from "1 1";
		 * but PCB buttons don't support that bit.
		 *
		 * So we must synthesize release events.  We do that by
		 * mapping events to a press/release event pair; then
		 * to avoid adding extra events, skip the second event
		 * of each pair.
		 */
		if (event == last_event) {
			last_event = 0;
			continue;
		}
		last_event = event;

		/* ignore the RC5 toggle bit */
		event &= ~0x0800;

		/* find the key, or leave it as unknown */
		keycode = KEY_UNKNOWN;
		for (i = 0; i < ARRAY_SIZE(dm355evm_keys); i++) {
			if (dm355evm_keys[i].event != event)
				continue;
			keycode = dm355evm_keys[i].keycode;
			break;
		}
		dev_dbg(keys->dev,
			"input event 0x%04x--> keycode %d\n",
			event, keycode);

		/* report press + release */
		input_report_key(keys->input, keycode, 1);
		input_sync(keys->input);
		input_report_key(keys->input, keycode, 0);
		input_sync(keys->input);
	}
177 178 179
	return IRQ_HANDLED;
}

180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253
static int dm355evm_setkeycode(struct input_dev *dev, int index, int keycode)
{
	u16		old_keycode;
	unsigned	i;

	if (((unsigned)index) >= ARRAY_SIZE(dm355evm_keys))
		return -EINVAL;

	old_keycode = dm355evm_keys[index].keycode;
	dm355evm_keys[index].keycode = keycode;
	set_bit(keycode, dev->keybit);

	for (i = 0; i < ARRAY_SIZE(dm355evm_keys); i++) {
		if (dm355evm_keys[index].keycode == old_keycode)
			goto done;
	}
	clear_bit(old_keycode, dev->keybit);
done:
	return 0;
}

static int dm355evm_getkeycode(struct input_dev *dev, int index, int *keycode)
{
	if (((unsigned)index) >= ARRAY_SIZE(dm355evm_keys))
		return -EINVAL;

	return dm355evm_keys[index].keycode;
}

/*----------------------------------------------------------------------*/

static int __devinit dm355evm_keys_probe(struct platform_device *pdev)
{
	struct dm355evm_keys	*keys;
	struct input_dev	*input;
	int			status;
	int			i;

	/* allocate instance struct and input dev */
	keys = kzalloc(sizeof *keys, GFP_KERNEL);
	input = input_allocate_device();
	if (!keys || !input) {
		status = -ENOMEM;
		goto fail1;
	}

	keys->dev = &pdev->dev;
	keys->input = input;

	/* set up "threaded IRQ handler" */
	status = platform_get_irq(pdev, 0);
	if (status < 0)
		goto fail1;
	keys->irq = status;

	input_set_drvdata(input, keys);

	input->name = "DM355 EVM Controls";
	input->phys = "dm355evm/input0";
	input->dev.parent = &pdev->dev;

	input->id.bustype = BUS_I2C;
	input->id.product = 0x0355;
	input->id.version = dm355evm_msp_read(DM355EVM_MSP_FIRMREV);

	input->evbit[0] = BIT(EV_KEY);
	for (i = 0; i < ARRAY_SIZE(dm355evm_keys); i++)
		__set_bit(dm355evm_keys[i].keycode, input->keybit);

	input->setkeycode = dm355evm_setkeycode;
	input->getkeycode = dm355evm_getkeycode;

	/* REVISIT:  flush the event queue? */

254 255
	status = request_threaded_irq(keys->irq, NULL, dm355evm_keys_irq,
			IRQF_TRIGGER_FALLING, dev_name(&pdev->dev), keys);
256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319
	if (status < 0)
		goto fail1;

	/* register */
	status = input_register_device(input);
	if (status < 0)
		goto fail2;

	platform_set_drvdata(pdev, keys);

	return 0;

fail2:
	free_irq(keys->irq, keys);
fail1:
	input_free_device(input);
	kfree(keys);
	dev_err(&pdev->dev, "can't register, err %d\n", status);

	return status;
}

static int __devexit dm355evm_keys_remove(struct platform_device *pdev)
{
	struct dm355evm_keys	*keys = platform_get_drvdata(pdev);

	free_irq(keys->irq, keys);
	input_unregister_device(keys->input);
	kfree(keys);

	return 0;
}

/* REVISIT:  add suspend/resume when DaVinci supports it.  The IRQ should
 * be able to wake up the system.  When device_may_wakeup(&pdev->dev), call
 * enable_irq_wake() on suspend, and disable_irq_wake() on resume.
 */

/*
 * I2C is used to talk to the MSP430, but this platform device is
 * exposed by an MFD driver that manages I2C communications.
 */
static struct platform_driver dm355evm_keys_driver = {
	.probe		= dm355evm_keys_probe,
	.remove		= __devexit_p(dm355evm_keys_remove),
	.driver		= {
		.owner	= THIS_MODULE,
		.name	= "dm355evm_keys",
	},
};

static int __init dm355evm_keys_init(void)
{
	return platform_driver_register(&dm355evm_keys_driver);
}
module_init(dm355evm_keys_init);

static void __exit dm355evm_keys_exit(void)
{
	platform_driver_unregister(&dm355evm_keys_driver);
}
module_exit(dm355evm_keys_exit);

MODULE_LICENSE("GPL");
新手
引导
客服 返回
顶部