Skip to content

Q
qemu

openeuler / qemu

通知 10
Star 0
Fork 0
Q
qemu

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 19 8月, 2010 3 次提交
  3. 16 8月, 2010 1 次提交
    • A
      sparc escc IUS improvements (SunOS 4.1.4 fix) · 9fc391f8
      由 Artyom Tarasenko 提交于 
      According to scc_escc_um.pdf:
 - Reset Highest IUS must update irq status to allow processing
   of the next priority interrupt.
 - rx interrupt has always higher priority than tx on same channel

The documentation only explicitly says that Reset Highest IUS
command (0x38) clears IUS bits, not that it clears the corresponding
interrupt too, so don't clear interrupts on this command.

The patch allows SunOS 4.1.4 to use the serial ports
Signed-off-by: NArtyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>
      9fc391f8
  5. 15 8月, 2010 7 次提交
  7. 11 8月, 2010 5 次提交
  9. 09 8月, 2010 2 次提交
  11. 08 8月, 2010 1 次提交
  13. 06 8月, 2010 3 次提交
  15. 04 8月, 2010 1 次提交
  17. 03 8月, 2010 7 次提交
    • A
      ide: Avoid canceling IDE DMA · 953844d1
      由 Andrea Arcangeli 提交于 
      The reason for not actually canceling the I/O is because with
virtualization and lots of VM running, a guest fs may mistake a
overload of the host, as an IDE timeout. So rather than canceling the
I/O, it's safer to wait I/O completion and simulate that the I/O has
completed just before the io cancellation was requested by the
guest. This way if ntfs or an app writes data without checking for
-EIO retval, and it thinks the write has succeeded, it's less likely
to run into troubles. Similar issues for reads.

Furthermore because the DMA operation is splitted into many synchronous
aio_read/write if there's more than one entry in the SG table, without this
patch the DMA would be cancelled in the middle, something we've no idea if it
happens on real hardware too or not. Overall this seems a great risk for zero
gain.

This approach is sure safer than previous code given we can't pretend all guest
fs code out there to check for errors and reply the DMA if it was completed
partially, given a timeout would never materialize on a real harddisk unless
there are defective blocks (and defective blocks are practically only an issue
for reads never for writes in any recent hardware as writing to blocks is the
way to fix them) or the harddisk breaks as a whole.
Signed-off-by: NIzik Eidus <ieidus@redhat.com>
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      953844d1
    • M
      block: Change bdrv_eject() not to drop the image · 4be9762a
      由 Markus Armbruster 提交于 
      bdrv_eject() gets called when a device model opens or closes the tray.

If the block driver implements method bdrv_eject(), that method gets
called.  Drivers host_cdrom implements it, and it opens and closes the
physical tray, and nothing else.  When a device model opens, then
closes the tray, media changes only if the user actively changes the
physical media while the tray is open.  This is matches how physical
hardware behaves.

If the block driver doesn't implement method bdrv_eject(), we do
something quite different: opening the tray severs the connection to
the image by calling bdrv_close(), and closing the tray does nothing.
When the device model opens, then closes the tray, media is gone,
unless the user actively inserts another one while the tray is open,
with a suitable change command in the monitor.  This isn't how
physical hardware behaves.  Rather inconvenient when programs
"helpfully" eject media to give you a chance to change it.  The way
bdrv_eject() behaves here turns that chance into a must, which is not
what these programs or their users expect.

Change the default action not to call bdrv_close().  Instead, note the
tray status in new BlockDriverState member tray_open.  Use it in
bdrv_is_inserted().

Arguably, the device models should keep track of tray status
themselves.  But this is less invasive.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      4be9762a
    • K
      block: Fix bdrv_has_zero_init · 336c1c12
      由 Kevin Wolf 提交于 
      Assuming that any image on a block device is not properly zero-initialized is
actually wrong: Only raw images have this problem. Any other image format
shouldn't care about it, they initialize everything properly themselves.
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      336c1c12
    • Y
      block migration: replace tabs by spaces. · bd0858bb
      由 Yoshiaki Tamura 提交于 
      Signed-off-by: NYoshiaki Tamura <tamura.yoshiaki@lab.ntt.co.jp>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      bd0858bb
    • M
      loadvm: improve tests before bdrv_snapshot_goto() · f0aa7a8b
      由 Miguel Di Ciurcio Filho 提交于 
      This patch improves the resilience of the load_vmstate() function, doing
further and better ordered tests.

In load_vmstate(), if there is any error on bdrv_snapshot_goto(), except if the
error is on VM state device, load_vmstate() will return zero and the VM will be
started with major corruption chances.

The current process:
- test if there is any writable device without snapshot support
    - if exists return -error
- get the device that saves the VM state, possible return -error but unlikely
because it was tested earlier
- flush I/O
- run bdrv_snapshot_goto() on devices
    - if fails, give an warning and goes to the next (not good!)
    - if fails on the VM state device, return zero (not good!)
- check if the requested snapshot exists on the device that saves the VM state
and the state is not zero
    - if fails return -error
- open the file with the VM state
    - if fails return -error
- load the VM state
    - if fails return -error
- return zero

New behavior:
- get the device that saves the VM state
    - if fails return -error
- check if the requested snapshot exists on the device that saves the VM state
and the state is not zero
    - if fails return -error
- test if there is any writable device without snapshot support
    - if exists return -error
- test if the devices with snapshot support have the requested snapshot
    - if anyone fails, return -error
- flush I/O
- run snapshot_goto() on devices
    - if anyone fails, return -error
- open the file with the VM state
    - if fails return -error
- load the VM state
    - if fails return -error
- return zero

do_loadvm must not call vm_start if any error has occurred in load_vmstate.
Signed-off-by: NMiguel Di Ciurcio Filho <miguel.filho@gmail.com>
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      f0aa7a8b
    • K
      block: Change bdrv_commit to handle multiple sectors at once · 8a426614
      由 Kevin Wolf 提交于 
      bdrv_commit copies the image to its backing file sector by sector, which
is (surprise!) relatively slow. Let's take a larger buffer and handle more
sectors at once if possible.

With a 1G qcow2 file, this brought the time bdrv_commit takes down from
5:06 min to 1:14 min for me.
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
      8a426614
    • A
      fix last cpu timer initialization · 5933e8a9
      由 Artyom Tarasenko 提交于 
      The timer #0 is the system timer, so the timer #num_cpu is the
timer of the last CPU, and it must be initialized in slavio_timer_reset.

Don't mark non-existing timers as running.
Signed-off-by: NArtyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>
      5933e8a9
  19. 01 8月, 2010 3 次提交
  21. 31 7月, 2010 7 次提交