Correct computation of vector offsets for EXCP_EXT_INTERRUPT.
For instance, if Cause.IV is 0 the vector offset should be 0x180.

Simplify the finding vector number logic for the Vectored Interrupts.
Signed-off-by: NYongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: NLeon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: cosmetic changes]
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NLeon Alrae <leon.alrae@imgtec.com>

Fix buglets for 2.4

# gpg: Signature made Mon Jul 27 15:26:48 2015 BST using RSA key ID 4DD0279B
# gpg: Good signature from "Richard Henderson <rth7680@gmail.com>"
# gpg:                 aka "Richard Henderson <rth@redhat.com>"
# gpg:                 aka "Richard Henderson <rth@twiddle.net>"

* remotes/rth/tags/pull-tcg-20150727:
  tcg: mark temps as mem_coherent = 0 for mov with a constant
  tcg: correctly mark dead inputs for mov with a constant
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

aio_notify can be optimized away, and in fact almost always will.  However,
qemu_notify_event is used in places where this is incorrect---most notably,
when handling SIGTERM.  When aio_notify is optimized away, it is possible that
QEMU enters a blocking ppoll immediately afterwards and stays there, without
reaching main_loop_should_exit().

Fix this by using a bottom half.  The bottom half can be optimized too, but
scheduling it is enough for the ppoll not to block.  The hang is thus avoided.
Reported-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1437738175-23624-1-git-send-email-pbonzini@redhat.com
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

Unfortunately Ubuntu's pkg-config information for gnutls is broken
for the static linking case, and outputs --libs options which the
compiler does not recognize. Work around this problem by testing
that the --cflags/--libs output will at least allow compilation
before enabling gnutls support.
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NDaniel P. Berrange <berrange@redhat.com>
Message-id: 1437758888-22486-1-git-send-email-peter.maydell@linaro.org

When a constant has to be loaded in a mov op, we fail to set
mem_coherent = 0. This patch fixes that.

Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Message-Id: <1437994568-7825-3-git-send-email-aurelien@aurel32.net>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

When tcg_reg_alloc_mov propagate a constant, we failed to correctly mark
a temp as dead if the liveness analysis hints so. This fixes the
following assert when configure with --enable-debug-tcg:

  qemu-x86_64: tcg/tcg.c:1827: tcg_reg_alloc_bb_end: Assertion `ts->val_type == TEMP_VAL_DEAD' failed.

Cc: Richard Henderson <rth@twiddle.net>
Reported-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Message-Id: <1437994568-7825-2-git-send-email-aurelien@aurel32.net>
Signed-off-by: NRichard Henderson <rth@twiddle.net>

Pull request

Here are NIC fixes from Fam Zheng that prevent rx hangs (caused by NIC models
where .can_receive() stops rx but qemu_flush_queued_packets() isn't called).

# gpg: Signature made Mon Jul 27 14:51:48 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg:                 aka "Stefan Hajnoczi <stefanha@gmail.com>"

* remotes/stefanha/tags/net-pull-request:
  axienet: Flush queued packets when rx is done
  dp8393x: Flush packets when link comes up
  stellaris_enet: Flush queued packets when read done
  mipsnet: Flush queued packets when receiving is enabled
  milkymist-minimac2: Flush queued packets when link comes up
  mcf_fec: Drop mcf_fec_can_receive
  etsec: Flush queue when rx buffer is consumed
  etsec: Move etsec_can_receive into etsec_receive
  usbnet: Drop usbnet_can_receive
  eepro100: Drop nic_can_receive
  pcnet: Drop pcnet_can_receive
  xgmac: Drop packets with eth_can_rx is false.
  hw/net: fix mcf_fec driver receiver
  hw/net: add simple phy support to mcf_fec driver
  hw/net: add ANLPAR bit definitions to generic mii
  hw/net: create common collection of MII definitions
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

eth_can_rx checks s->rxsize and returns false if it is non-zero. Because
of the .can_receive semantics change, this will make the incoming queue
disabled by peer, until it is explicitly flushed. So we should flush it
when s->rxsize is becoming zero.

Squash eth_can_rx semantics into etx_rx and drop .can_receive()
callback, also add flush when rx buffer becomes available again after a
packet gets queued.

The other conditions, "!axienet_rx_resetting(s) &&
axienet_rx_enabled(s)" are OK because enet_write already calls
qemu_flush_queued_packets when the register bits are changed.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-13-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

.can_receive callback changes semantics that once return 0, backend will
try sending again until explicitly flushed, change the device to meet
that.

dp8393x_can_receive checks SONIC_CR_RXEN bit in SONIC_CR register and
SONIC_ISR_RBE bit in SONIC_ISR register, try flushing the queue when
either bit is being updated.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-12-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

If s->np reaches 31, the queue will be disabled by peer when it sees
stellaris_enet_can_receive() returns false, until we explicitly flushes
it which notifies the peer. Do this when guest is done reading all
existing data.

Move the semantics to stellaris_enet_receive, by returning 0 when the
buffer is full, so that new packets will be queued.  In
stellaris_enet_read, flush and restart the queue when guest has done
reading.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-11-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

Drop .can_receive and move the semantics to mipsnet_receive, by
returning 0.

After 0 is returned, we must flush the queue explicitly to restart it:
Call qemu_flush_queued_packets when s->busy or s->rx_count is being
updated.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-10-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

Drop .can_receive and move the semantics into minimac2_rx, by returning
0.

That is once minimac2_rx returns 0, incoming packets will be queued
until the queue is explicitly flushed. We do this when s->regs[R_STATE0]
or s->regs[R_STATE1] is changed in minimac2_write.

Also drop the unused trace point.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-9-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

The semantics of .can_receive requires us to flush the queue explicitly
when s->rx_enabled becomes true after it returns 0, but the packet being
queued is not meaningful since the guest hasn't activated the card.
Let's just drop the packet in this case.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-8-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

The BH will be scheduled when etsec->rx_buffer_len is becoming 0, which
is the condition of queuing.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-7-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

When etsec_reset returns 0, peer would queue the packet as if
.can_receive returns false. Drop etsec_can_receive and let etsec_receive
carry the semantics.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-6-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

usbnet_receive already drops packet if rndis_state is not
RNDIS_DATA_INITIALIZED, and queues packet if in buffer is not available.
The only difference is s->dev.config but that is similar to rndis_state.

Drop usbnet_can_receive and move these checks to usbnet_receive, so that
we don't need to explicitly flush the queue when s->dev.config changes
value.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-5-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

nic_receive already checks the conditions and drop packets if false.
Due to the new semantics since 6e99c631 ("net/socket: Drop
net_socket_can_send"), having .can_receive returning 0 requires us to
explicitly flush the queued packets when the conditions are becoming
true, but queuing the packets when guest driver is not ready doesn't
make much sense.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-4-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

pcnet_receive already checks the conditions and drop packets if false.
Due to the new semantics since 6e99c631 ("net/socket: Drop
net_socket_can_send"), having .can_receive returning 0 requires us to
explicitly flush the queued packets when the conditions are becoming
true, but queuing the packets when guest driver is not ready doesn't
make much sense.
Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-3-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

Signed-off-by: NFam Zheng <famz@redhat.com>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-2-git-send-email-famz@redhat.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

The network mcf_fec driver emulated receive side method is returning a
result of 0 causing the network layer to disable receive for this emulated
device. This results in the guest only ever receiving one packet.

Fix the recieve side processing to return the number of bytes that we
passed back through to the guest.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-5-git-send-email-gerg@uclinux.org
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

The Linux fec driver needs at least basic phy support to probe and work.
The current qemu mcf_fec emulation has no support for the reading or
writing of the MDIO lines to access an attached phy.

This code adds a very simple set of register results for a fixed phy
setup - very similar to that used on an m5208evb board. This is enough
to probe and identify an emulated attached phy.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-4-git-send-email-gerg@uclinux.org
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

Add a base set of bit definitions for the standard MII phy "Auto-Negotiation
Link Partner Ability Register" (ANLPAR).

The original definitions moved into mii.h from the allwinner_emac driver
did not define these.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-3-git-send-email-gerg@uclinux.org
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

Create a common set of definitions of address and register values for
ethernet MII phys. A few of the current ethernet drivers have at least
a partial set of these definitions. Others just use hard coded raw
constant numbers.

This initial set is copied directly from the allwinner_emac code.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Reviewed-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-2-git-send-email-gerg@uclinux.org
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>

# gpg: Signature made Mon Jul 27 13:01:10 2015 BST using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: FAEB 9711 A12C F475 812F  18F2 88A9 064D 1835 61EB
#      Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76  CBD0 7DEF 8106 AAFC 390E

* remotes/jnsnow/tags/cve-2015-5154-pull-request:
  ide: Clear DRQ after handling all expected accesses
  ide/atapi: Fix START STOP UNIT command completion
  ide: Check array bounds before writing to io_buffer (CVE-2015-5154)
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

This is additional hardening against an end_transfer_func that fails to
clear the DRQ status bit. The bit must be unset as soon as the PIO
transfer has completed, so it's better to do this in a central place
instead of duplicating the code in all commands (and forgetting it in
some).
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NJohn Snow <jsnow@redhat.com>

The command must be completed on all code paths. START STOP UNIT with
pwrcnd set should succeed without doing anything.
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NJohn Snow <jsnow@redhat.com>

If the end_transfer_func of a command is called because enough data has
been read or written for the current PIO transfer, and it fails to
correctly call the command completion functions, the DRQ bit in the
status register and s->end_transfer_func may remain set. This allows the
guest to access further bytes in s->io_buffer beyond s->data_end, and
eventually overflowing the io_buffer.

One case where this currently happens is emulation of the ATAPI command
START STOP UNIT.

This patch fixes the problem by adding explicit array bounds checks
before accessing the buffer instead of relying on end_transfer_func to
function correctly.

Cc: qemu-stable@nongnu.org
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NJohn Snow <jsnow@redhat.com>

* qemu-char fixes
* SCSI fixes (including CVE-2015-5158)
* RCU fixes
* Framebuffer logic to set DIRTY_MEMORY_VGA
* Fix compiler warning for --disable-vnc
* qemu-doc fixes
* x86 TCG pasto fix

# gpg: Signature made Fri Jul 24 12:57:52 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg:                 aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg:          It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4  E2F7 7E15 100C CD36 69B1
#      Subkey fingerprint: F133 3857 4B66 2389 866C  7682 BFFB D25F 78C7 AE83

* remotes/bonzini/tags/for-upstream:
  target-i386/FPU: a misprint in helper_fistll_ST0
  qemu-doc: fix typos
  framebuffer: set DIRTY_MEMORY_VGA on RAM that is used for the framebuffer
  memory: count number of active VGA logging clients
  vl: Fix compiler warning for builds without VNC
  scsi: Handle no media case for scsi_get_configuration
  rcu: actually register threads that have RCU read-side critical sections
  scsi: fix buffer overflow in scsi_req_parse_cdb (CVE-2015-5158)
  vnc: fix memory leak
  qemu-char: Fix missed data on unix socket
  qemu-char: handle EINTR for TCP character devices
  exec.c: Use atomic_rcu_read() to access dispatch in memory_region_section_get_iotlb()
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

There is a cut-and-paste mistake in the patch
https://lists.gnu.org/archive/html/qemu-devel/2014-11/msg01657.html .
It cause errors in guest work.  Here is the bugfix.
Signed-off-by: NDmitry Poletaev <poletaev-qemu@yandex.ru>
Reported-by: NKirill Batuzov <batuzovk@ispras.ru>
Message-Id: <2692911436348920@web2m.yandex.ru>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Signed-off-by: NGonglei <arei.gonglei@huawei.com>
Message-Id: <1435917057-9396-1-git-send-email-arei.gonglei@huawei.com>
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The MemoryRegionSection contains enough information to access the
RAM region underlying the framebuffer, and can be cached inside the
display device.

By doing this, the new framebuffer_update_memory_section function can
enable dirty memory logging on the relevant RAM region.  The function
must be called whenever the stride or base of the framebuffer changes;
a simple way to cover these cases is to call it on every full frame
invalidation, which is a rare case.

framebuffer_update_display now works entirely on a MemoryRegionSection,
without going through cpu_physical_memory_map/unmap.
Reviewed-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

For a board that has multiple framebuffer devices, both of them
might want to use DIRTY_MEMORY_VGA on the same memory region.
The lack of reference counting in memory_region_set_log makes
this very awkward to implement.
Suggested-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

This regression was caused by commit 70b94331.

  CC    vl.o
vl.c: In function ‘select_display’:
vl.c:2064:12: error: unused variable ‘err’ [-Werror=unused-variable]
     Error *err = NULL;
            ^
Reported-by: NClaudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: NStefan Weil <sw@weilnetz.de>
Message-Id: <1437587610-26433-1-git-send-email-sw@weilnetz.de>
Reviewed-by: NWen Congyang <wency@cn.fujitsu.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Currently, scsi_get_configuration always returns a current
profile (DVD or CD), even when there is actually no media present.
By comparison, ide/atapi uses a default profile of 0 (MMC_PROFILE_NONE)
for this case and checks for tray_open, so let's do the same for scsi.

This fixes a problem I'm seeing with Fedora 22 guests where systemd
cdrom_id fails to unmount after a QEMU-initiated eject against a
scsi cdrom device because it believes the media is still present
(but unreadable).
Signed-off-by: NMatthew Rosato <mjrosato@linux.vnet.ibm.com>
Message-Id: <1436986352-10695-1-git-send-email-mjrosato@linux.vnet.ibm.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Otherwise, grace periods are detected too early!
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

This is a guest-triggerable buffer overflow present in QEMU 2.2.0
and newer.  scsi_cdb_length returns -1 as an error value, but the
caller does not check it.

Luckily, the massive overflow means that QEMU will just SIGSEGV,
making the impact much smaller.
Reported-by: NZhu Donghai (朱东海) <donghai.zdh@alibaba-inc.com>
Fixes: 1894df02Reviewed-by: NFam Zheng <famz@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

If vnc's password is configured, it will leak memory
which cipher variable pointed on every vnc connection.

Cc: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: NDaniel P. Berrange <berrange@redhat.com>
Signed-off-by: NGonglei <arei.gonglei@huawei.com>
Message-Id: <1437556133-11268-1-git-send-email-arei.gonglei@huawei.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

Last minute fixes for 2.4.

# gpg: Signature made Fri Jul 24 04:42:31 2015 BST using RSA key ID 4DD0279B
# gpg: Good signature from "Richard Henderson <rth7680@gmail.com>"
# gpg:                 aka "Richard Henderson <rth@redhat.com>"
# gpg:                 aka "Richard Henderson <rth@twiddle.net>"

* remotes/rth/tags/pull-tcg-20150723:
  tcg/optimize: fix tcg_opt_gen_movi
  tcg/aarch64: use 32-bit offset for 32-bit softmmu emulation
  tcg/aarch64: use 32-bit offset for 32-bit user-mode emulation
  tcg/aarch64: add ext argument to tcg_out_insn_3310
  tcg/i386: Extend addresses for 32-bit guests
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>

VFIO fixes for v2.4.0-rc3
- Fix Realtek NIC quirk (Alex Williamson)
- Restore bootindex functionality (Alex Williamson)

# gpg: Signature made Thu Jul 23 19:51:23 2015 BST using RSA key ID 3BB08B22
# gpg: Good signature from "Alex Williamson <alex.williamson@redhat.com>"
# gpg:                 aka "Alex Williamson <alex@shazbot.org>"
# gpg:                 aka "Alex Williamson <alwillia@redhat.com>"
# gpg:                 aka "Alex Williamson <alex.l.williamson@gmail.com>"

* remotes/awilliam/tags/vfio-fixes-20150723.0:
  vfio/pci: Fix bootindex
  vfio/pci: Fix RTL8168 NIC quirks
Signed-off-by: NPeter Maydell <peter.maydell@linaro.org>