xen_domainbuild and xen_machine_pv are built only for i386 targets.
Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

And put braces for blocks with a single statement.
Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Acked-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAlexander Graf <agraf@suse.de>

With this new field, we can specified which accelerator use to run the
machine, if the accelerator is not already specified by either a
configuration file or the command line options.

Currently, the only use will be made in the xenfv machine.
Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This option gives the ability to switch one "accelerator" like kvm, xen
or the default one tcg. We can specify more than one accelerator by
separate them by a colon. QEMU will try each one and use the first whose
works.

So,
./qemu -machine accel=xen:kvm:tcg

which would try Xen support first, then KVM and finally TCG if none of
the other works.

By default, QEMU will use TCG. But we can specify another default in the
global configuration file.
Signed-off-by: NAnthony PERARD <anthony.perard@citrix.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This interrupt name is used by i386, CRIS, and MicroBlaze.
Copy the name into each target.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

SMI, VIRQ, INIT, SIPI, and MCE are all only used by the i386 port.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This interrupt name was only used by the ARM port.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

It is no longer used anywhere.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This bit is never set, therefore we should not read it either.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This bit is never set, therefore we should not read it either.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

This mask contains all of the bits that should be ignored while single
stepping in the debugger.  The mask contains 2 bits that are not currently
cleared, but are also never set.  The bits are included in the mask for
consistency in handling of the CPU_INTERRUPT_TGT_EXT_N bits.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

These defines will be place-holders for cpu-specific functionality.
Generic code will, at the end of the patch series, no longer have to
concern itself about how SMI, NMI, etc should be handled.  Instead,
generic code will know only that the interrupt is internal or external.
Signed-off-by: NRichard Henderson <rth@twiddle.net>
Signed-off-by: NBlue Swirl <blauwirbel@gmail.com>

Conflicts:
	exec.c

When we're trying to get a newly registered phys memory client updated
with the current page mappings, we end up passing the region offset
(a ram_addr_t) as the start address rather than the actual guest
physical memory address (target_phys_addr_t).  If your guest has less
than 3.5G of memory, these are coincidentally the same thing.  If
there's more, the region offset for the memory above 4G starts over
at 0, so the set_memory client will overwrite it's lower memory entries.

Instead, keep track of the guest phsyical address as we're walking the
tables and pass that to the set_memory client.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

When we register a physical memory client, we try to walk the page
tables, calling the set_memory hook for every entry.  Effectively
playing catchup for the client for everything already registered.
With this type, we only walk the 2nd entry of the l1 table,
typically missing all of the registered memory.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Used by HD audio controllers like our intel-hda.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

msi_init may fail, so we need to check on uninit if the cap was
actually installed. This also avoids that the users need to check.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

The general control register is a byte register.
Add support for byte reads.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

MDI control is a 32 bit register, but may be read or written using
8 or 16 bit access. Data is latched when the MSB is written.

Add support for byte/word read/write access.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

pointer is a 32 bit register, but may be written using 8 or 16 bit writes.
Add support for byte/word writes.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

port is a 32 bit register, but may be written using 8 or 16 bit writes.
Add support for byte/word writes.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Like other Intel devices, e100 (eepro100) uses little endian byte order.

This patch was tested with these combinations:

i386 host, i386 + mipsel guests (le-le)
mipsel host, i386 guest (le-le)
i386 host, mips + ppc guests (le-be)
mips host, i386 guest (be-le)

mips and mipsel hosts were emulated machines.

v2:
Use prefix for new functions. Add the same prefix to stl_le_phys.
Fix alignment of mem (needed for word/dword reads/writes).
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

QEMU sends frames smaller than 60 bytes to ethernet nics.
Such frames are rejected by real NICs and their emulations.
To avoid this behaviour, other NIC emulations pad received
frames. This patch enables this workaround for eepro100, too.

All related code is marked with CONFIG_PAD_RECEIVED_FRAMES,
so we can drop this in case QEMU's networking code is
ever changed.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

cppcheck reports that 'packet' is unused.

It was only used to calculate the size of the preceding data.
Removing it saves a lot of stack space (local variable rx).
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

When DEBUG_EEPRO100 was enabled, unsupported writes were logged twice.
Now logging in eepro100_write1 and eepro100_write2 is similar to the
logging in eepro100_write4 (which already was correct).
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Initialize scsi_len with zero when starting a new request, so any
stuff leftover from the previous request is cleared out.  This may
happen in case the data returned by the scsi command doesn't fit
into the buffer provided by the guest.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>

Windows allows control transfers to pass up to 4k of data, so raise our
control buffer size to 4k. For control out transfers the usb core code copies
the control request data to a buffer before calling the device's handle_control
callback. Add a check for overflowing the buffer before copying the data.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Extend the iso buffering code to also buffer iso out packets, this
fixes for example using usb speakers with usb redirection.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Currently we reserve room for endpoint data for 16 endpoints, but given
that we only use endpoint data for endpoints 1-15, and always index the
array with the endpoint-number - 1, 15 is enough.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Refuse iso usb packets when then max packet size for the endpoint is 0,
this avoids an abort in usb_host_alloc_iso() caused by trying to qemu_malloc
a 0 bytes large buffer.

If an endpoint is not in the usb descriptor we've no idea what kind of
endpoint it is and thus how to handle it, refuse packages in this case.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>