Drops manual hole punching in PCI0._CRS on PIIX4 machine type
for CPU hotplug resources.
Resources will be consumed by Device(PRES) that is attached
to PCI bus. The same way how it currently works for mem hotlpug.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Drops manual hole punching in PCI0._CRS for PIIX4 machine type.
Resources will be consumed by Device(PHPR) that cwis attached
to PCI bus. The same way how it currently works for mem hotlpug.

Manual hole in PIIX4 _CRS wasn't correct anyway since it was
legacy size 0xF while current PCIHP MMIO region is of size 0x14.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Replace template patching and runtime calculation
in _CRS() method with static _CRS defined in SSDT.
No functional change except of as mentined above
and _CRS being moved from DSDT to SSDT.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Provide the TIS 1.3 capability flags.
The interface now looks like a TIS 1.3 interface. It's fully
compatible with previous TIS 1.2 and drivers written for
TIS 1.2 continue to work.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Extend the backend to check whether the TPM_ContinueSelfTest
finished successfully and provide a flag to the TIS front-end
if it successfully finished. The TIS then sets a flag in
all localities in the STS register and keeps it until the next
reset.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Support for the XFIFO register (range) of the TIS 1.3 specification.
We support a range of 64 bytes.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Improve the access to the registers with 32 and 16 bit reads and writes.
Also enable access to a non-base register address, such as reads of the
2nd byte of a register. Map the FIFO byte access to any byte within
its 4 byte register (following specs).
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

More recent TIS specs extend the STS register to 32 bit. While
we don't store the TIS interface state, yet, we can extend it
without sideeffects.
Signed-off-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

The idea is that all other virtio devices are calling this helper
to merge properties of the proxy device. This is the only difference
in between this helper and code in inside virtio_instance_init_common.
The patch should not cause any harm as property list in generic balloon
code is empty.

This also allows to avoid some dummy errors like fixed by this
    commit 91ba2120
    Author: Gonglei <arei.gonglei@huawei.com>
    Date:   Tue Sep 30 14:10:35 2014 +0800
    virtio-balloon: fix virtio-balloon child refcount in transports
Signed-off-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NRaushaniya Maksudova <rmaksudova@parallels.com>
Revieved-by: NCornelia Huck <cornelia.huck@de.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

A bunch of code moved from dsdt to ssdt,
plus we got trivial changes like 0->Zero which our test
dosn't recognize as identity yet.
Update expected files to suppress test warning.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

drop ssdt-mem.hex.generated and ssdt-proc.hex.generated:
dsl files have been removed previously.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Used for IASL builds.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it will be used later to dynamically reserve MMIO region
instead of manually punching holes in PCI0._CRS
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it replaces a static complied in DSDT MMIO region
for memory hotplug with one created at runtime
leaving only truly static memory hotplug related
ASL bits in DSDT. And replaces template patching
of MEMORY_SLOTS_NUMBER value with ASL API created
named value.

Later it also would make easier to reuse current
ACPI memory hotplug on other targets.

Also later it would be possible to move remaining
memory hotplug ASL methods into build_ssdt() and
add all memory hotplug related AML into SSDT only
when memory hotplug is enabled, further reducing
ACPI tables blob if memory hotplug isn't used.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

in addition it saves us ~330LOC and makes it one binary blob less
stored in QEMU source tree by removing need to keep and update
hw/i386/ssdt-mem.hex.generated file there.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

it replaces a static complied in DSDT MMIO region
for CPU hotplug with one created at runtime
leaving only truly static CPU hotplug related ASL
bits in DSDT.
It also puts CPU_HOTPLUG_RESOURCE_DEVICE into
PCI0 scope and reserves resources from it,
preparing for dropping manual hole punching
in PCI0._CRS.

Later it also would make easier to reuse current
ACPI CPU hotplug on other targets.

Also later it would be possible to move remaining
CPU hotplug ASL methods into build_ssdt() and
add all CPU hotplug related AML into SSDT only
when CPU hotplug is enabled, further reducing
ACPI tables blob if CPU hotplug isn't used.

impl. detail:
Windows XP can't handle /BSODs/ OperationRegion
declaration in DSDT when variable from SSDT is used
for specifying its address/length and also when
Field declared in DSDT with OperationRegion from
SSDT if DSDT is being parsed before SSDT.
But it works just fine when referencing named
fields from another table. Hence OperationRegion
and Field declaration are moved to SSDT to make
XP based editions work.

PS:
Later Windows editions seem to be fine with above
conditions.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

in addition it saves us ~400LOC and makes it
one binary blob less stored in QEMU source
tree by removing need to keep and update
hw/i386/ssdt-proc.hex.generated file there.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Drops AML template patching and allows to
save some space in SSDT if pvpanic device doesn't
exist by not including disabled device description
into SSDT. It also makes device description
smaller by replacing _STA method with named value
and dropping _INI method.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Named/Reserved{Field} definition uses PkgLength [1] encoding to specify
field length, however it doesn't include size of PkgLength field itself,
while other block objects that have explicit length of its body account
for PkgLength size while encoding it [2].
This special casing isn't mentioned in ACPI spec, but that's what 'iasl'
compiles NamedField to so add extra argument to build_prepend_pkg_length()
to allow it handle the case.

--
1. ACPI Spec 5.0, 20.2.5.2 Named Objects Encoding, page 822
2. ACPI Spec 5.0, 5.4 Definition Block Encoding
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Replaces template patching with packages composed
using AML API.

Note on behavior change:
If S3 or S4 is disabled, respective packages won't
be created and put into SSDT. Which saves us some
space in SSDT and doesn't confuse guest OS with
mangled package names as it was done originally.
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
Reviewed-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>