Skip to content

Q
qemu

openeuler / qemu

通知 10
Star 0
Fork 0
Q
qemu
切换分支/标签
  1. 26 5月, 2016 1 次提交
  3. 24 5月, 2016 2 次提交
    • G
      migration: regain control of images when migration fails to complete · fe904ea8
      由 Greg Kurz 提交于 
      We currently have an error path during migration that can cause
the source QEMU to abort:

migration_thread()
  migration_completion()
    runstate_is_running() ----------------> true if guest is running
    bdrv_inactivate_all() ----------------> inactivate images
    qemu_savevm_state_complete_precopy()
     ... qemu_fflush()
           socket_writev_buffer() --------> error because destination fails
         qemu_fflush() -------------------> set error on migration stream
  migration_completion() -----------------> set migrate state to FAILED
migration_thread() -----------------------> break migration loop
  vm_start() -----------------------------> restart guest with inactive
                                            images

and you get:

qemu-system-ppc64: socket_writev_buffer: Got err=104 for (32768/18446744073709551615)
qemu-system-ppc64: /home/greg/Work/qemu/qemu-master/block/io.c:1342:bdrv_co_do_pwritev: Assertion `!(bs->open_flags & 0x0800)' failed.
Aborted (core dumped)

If we try postcopy with a similar scenario, we also get the writev error
message but QEMU leaves the guest paused because entered_postcopy is true.

We could possibly do the same with precopy and leave the guest paused.
But since the historical default for migration errors is to restart the
source, this patch adds a call to bdrv_invalidate_cache_all() instead.
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Message-Id: <146357896785.6003.11983081732454362715.stgit@bahia.huguette.org>
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
      fe904ea8
    • G
      savevm: fail if migration blockers are present · 24f3902b
      由 Greg Kurz 提交于 
      QEMU has currently two ways to prevent migration to occur:
- migration blocker when it depends on runtime state
- VMStateDescription.unmigratable when migration is not supported at all

This patch gathers all the logic into a single function to be called from
both the savevm and the migrate paths.

This fixes a bug with 9p, at least, where savevm would succeed and the
following would happen in the guest after loadvm:

$ ls /host
ls: cannot access /host: Protocol error

With this patch:

(qemu) savevm foo
Migration is disabled when VirtFS export path '/' is mounted in the guest
using mount_tag 'host'
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Message-Id: <146239057139.11271.9011797645454781543.stgit@bahia.huguette.org>

[Update subject according to Paolo's suggestion - Amit]
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
      24f3902b
  5. 23 5月, 2016 4 次提交
  7. 19 5月, 2016 2 次提交
  9. 18 5月, 2016 1 次提交
  11. 23 3月, 2016 2 次提交
    • V
      util: move declarations out of qemu-common.h · f348b6d1
      由 Veronia Bahaa 提交于 
      Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: NVeronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      f348b6d1
    • M
      include/qemu/osdep.h: Don't include qapi/error.h · da34e65c
      由 Markus Armbruster 提交于 
      Commit 57cb38b3 included qapi/error.h into qemu/osdep.h to get the
Error typedef.  Since then, we've moved to include qemu/osdep.h
everywhere.  Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h.  That's in excess of
100KiB of crap most .c files don't actually need.

Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h.  Include qapi/error.h in .c files that need it and don't
get it now.  Include qapi-types.h in qom/object.h for uint16List.

Update scripts/clean-includes accordingly.  Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h.  Update the list of includes in the qemu/osdep.h
comment quoted above similarly.

This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third.  Unfortunately, the number depending on
qapi-types.h shrinks only a little.  More work is needed for that one.
Signed-off-by: NMarkus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      da34e65c
  13. 11 3月, 2016 5 次提交
  15. 08 3月, 2016 1 次提交
  17. 28 2月, 2016 1 次提交
  19. 26 2月, 2016 4 次提交
  21. 25 2月, 2016 1 次提交
  23. 23 2月, 2016 1 次提交
    • D
      Postcopy+spice: Pass spice migration data earlier · b82fc321
      由 Dr. David Alan Gilbert 提交于 
      Spice hooks the migration status changes to figure out when to
transmit information to the new spice server; but the migration
status in postcopy doesn't quite fit - the destination starts
running before the end of the source migration.

It's not a case of hanging off the migration status change to
postcopy-active either, since that happens before we stop the
guest CPU.

Fix it by sending a notify just after sending the device state,
and adding a flag that can be tested by the notify receiver.

Symptom:
   spice handover doesn't work with the error:
   red_worker.c:11540:display_channel_wait_for_migrate_data: timeout
Signed-off-by: NDr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: NAmit Shah <amit.shah@redhat.com>
Message-id: 1456161452-25318-1-git-send-email-dgilbert@redhat.com
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
      b82fc321
  25. 22 2月, 2016 1 次提交
  27. 16 2月, 2016 1 次提交
  29. 11 2月, 2016 1 次提交
  31. 09 2月, 2016 1 次提交
    • S
      memory: RCU ram_list.dirty_memory[] for safe RAM hotplug · 5b82b703
      由 Stefan Hajnoczi 提交于 
      Although accesses to ram_list.dirty_memory[] use atomics so multiple
threads can safely dirty the bitmap, the data structure is not fully
thread-safe yet.

This patch handles the RAM hotplug case where ram_list.dirty_memory[] is
grown.  ram_list.dirty_memory[] is change from a regular bitmap to an
RCU array of pointers to fixed-size bitmap blocks.  Threads can continue
accessing bitmap blocks while the array is being extended.  See the
comments in the code for an in-depth explanation of struct
DirtyMemoryBlocks.

I have tested that live migration with virtio-blk dataplane works.
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Message-Id: <1453728801-5398-2-git-send-email-stefanha@redhat.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      5b82b703
  33. 05 2月, 2016 6 次提交
  35. 29 1月, 2016 1 次提交
  37. 22 1月, 2016 1 次提交
  39. 20 1月, 2016 1 次提交
    • K
      block: Inactivate BDS when migration completes · 76b1c7fe
      由 Kevin Wolf 提交于 
      So far, live migration with shared storage meant that the image is in a
not-really-ready don't-touch-me state on the destination while the
source is still actively using it, but after completing the migration,
the image was fully opened on both sides. This is bad.

This patch adds a block driver callback to inactivate images on the
source before completing the migration. Inactivation means that it goes
to a state as if it was just live migrated to the qemu instance on the
source (i.e. BDRV_O_INACTIVE is set). You're then supposed to continue
either on the source or on the destination, which takes ownership of the
image.

A typical migration looks like this now with respect to disk images:

1. Destination qemu is started, the image is opened with
   BDRV_O_INACTIVE. The image is fully opened on the source.

2. Migration is about to complete. The source flushes the image and
   inactivates it. Now both sides have the image opened with
   BDRV_O_INACTIVE and are expecting the other side to still modify it.

3. One side (the destination on success) continues and calls
   bdrv_invalidate_all() in order to take ownership of the image again.
   This removes BDRV_O_INACTIVE on the resuming side; the flag remains
   set on the other side.

This ensures that the same image isn't written to by both instances
(unless both are resumed, but then you get what you deserve). This is
important because .bdrv_close for non-BDRV_O_INACTIVE images could write
to the image file, which is definitely forbidden while another host is
using the image.
Signed-off-by: NKevin Wolf <kwolf@redhat.com>
Reviewed-by: NEric Blake <eblake@redhat.com>
Reviewed-by: NJohn Snow <jsnow@redhat.com>
      76b1c7fe
  41. 16 1月, 2016 2 次提交